Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Testing the performance of one and two box models as tools for risk assessment of particle exposure during packing of inorganic fertilizer

  • Ribalta, Carla
  • Koivisto, Antti J.
  • López-Lilao, Ana
  • Estupiñá, Sara
  • Minguillón, María Cruz
  • Monfort, Eliseo
  • Viana, Mar
Modelling of particle exposure is a useful tool for preliminary exposure assessment in workplaces with low and high exposure concentrations. However, actual exposure measurements are needed to assess models reliability. Worker exposure was monitored during packing of an inorganic granulate fertilizer at industrial scale using small and big bags. Particle concentrations were modelled with one and two box models, where the emission source was estimated with the fertilizer's dustiness index. The exposure levels were used to calculate inhaled dose rates and test accuracy of the exposure modellings. The particle number concentrations were measured from worker area by using a mobility and optical particle sizer which were used to calculate surface area and mass concentrations. The concentrations in the worker area during pre-activity ranged 63,797–81,073 cm−3, 4.6 × 106 to 7.5 × 106 μm2 cm−3, and 354 to 634 μg m−3 (respirable mass fraction) and during packing 50,300 to 85,949 cm−3, 4.3 × 106 to 7.6 × 106 μm2 cm−3, and 279 to 668 μg m−3 (respirable mass fraction). Thus, the packing process did not significantly increase the exposure levels. Chemical exposure was also under control based on REACH standards. The particle surface area deposition rate in respiratory tract was up to 7.6 × 106 μm2 min−1 during packing, with 52%–61% of deposition occurring in the alveolar region. Ratios of the modelled and measured concentrations were 0.98 ± 0.19 and 0.84 ± 0.12 for small and big bags, respectively, when using the one box model, and 0.88 ± 0.25 and 0.82 ± 0.12, when using the two box model. The modelling precision improved for both models when outdoor particle concentrations were included. This study shows that exposure concentrations in a low emission industrial scenario, e.g. during packing of a fertilizer, can be predicted with a reasonable accuracy by using the concept of dustiness and mass balance models., This research was founded by the Spanish MINECO (CGL2015-66777-C2-1-R, 2-R), Generalitat de Catalunya AGAUR 2017 SGR41, the Spanish Ministry of the Environment (13CAES006), FEDER (European Regional Development Fund) “Una manera de hacer Europa” and H2020 project caLIBRAte (Work Package 7). M.C. Minguillón acknowledges the Ramón y Cajal Fellowship awarded by the Spanish Ministry of Economy, Industry and Competitiveness. The authors also acknowledge the company in which the measurements were carried out for their support. The authors declare no conflict of interest relating to the material presented in this article., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Health risk assessment from exposure to particles during packing in working environments

  • Ribalta, Carla
  • López-Lilao, Ana
  • Estupiñá, Sara;
  • Fonseca, Ana Sofía
  • Tobías, Aurelio
  • García-Cobos, A.
  • Minguillón, María Cruz
  • Monfort, E.
  • Viana, Mar
Packing of raw materials in work environments is a known source of potential health impacts (respiratory, cardiovascular) due to exposure to airborne particles. This activity was selected to test different exposure and risk assessment tools, aiming to understand the effectiveness of source enclosure as a strategy to mitigate particle release. Worker exposure to particle mass and number concentrations was monitored during packing of 7 ceramic materials in 3 packing lines in different settings, with low (L), medium (M) and high (H) degrees of source enclosure. Results showed that packing lines L and M significantly increased exposure concentrations (119–609 μg m−3 respirable, 1150–4705 μg m−3 inhalable, 24,755–51,645 cm−3 particle number), while non-significant increases were detected in line H. These results evidence the effectiveness of source enclosure as a mitigation strategy, in the case of packing of ceramic materials. Total deposited particle surface area during packing ranged between 5.4 and 11.8 × 105 μm2 min−1, with particles depositing mainly in the alveoli (51–64%) followed by head airways (27–41%) and trachea bronchi (7–10%). The comparison between the results from different risk assessment tools (Stoffenmanager, ART, NanoSafer) and the actual measured exposure concentrations evidenced that all of the tools overestimated exposure concentrations, by factors of 1.5–8. Further research is necessary to bridge the current gap between measured and modelled health risk assessments., This research was founded by the Spanish MINECO (CGL2015-66777-C2-1-R, 2-R), Generalitat de Catalunya AGAUR 2017 SGR41, the Spanish Ministry of the Environment (13CAES006), and FEDER (European Regional Development Fund) “Una manera de hacer Europa”. Additional support was provided by caLIBRAte project funded by the European Union‘s Horizon 2020 research and innovation programme under grant agreement No 686239. M.C. Minguillón acknowledges the Ramón y Cajal Fellowship awarded by the Spanish Ministry of Economy, Industry and Competitiveness. The authors also acknowledge the company in which the measurements were carried out for their support. The authors declare no conflict of interest relating to the material presented in this article., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pulmonary toxicity of synthetic amorphous silica–effects of porosity and copper oxide doping

  • Hadrup, N.
  • Aimonen, K.
  • Ilves, M.
  • Lindberg, H.
  • Atluri, R.
  • Sahlgren, N.M.
  • Jacobsen, N.R.
  • Barfod, K.K.
  • Berthing, T.
  • Lawlor, A.
  • Norppa, H.
  • Wolff, H.
  • Jensen, K.A.
  • Hougaard, K.S.
  • Alenius, H.
  • Catalan, J.
  • Vogel, U.
Materials can be modified for improved functionality. Our aim was to test whether pulmonary toxicity of silica nanomaterials is increased by the introduction of: a) porosity; and b) surface doping with CuO; and whether c) these modifications act synergistically. Mice were exposed by intratracheal instillation and for some doses also oropharyngeal aspiration to: 1) solid silica 100 nm; 2) porous silica 100 nm; 3) porous silica 100 nm with CuO doping; 4) solid silica 300 nm; 5) porous silica 300 nm; 6) solid silica 300 nm with CuO doping; 7) porous silica 300 nm with CuO doping; 8) CuO nanoparticles 9.8 nm; or 9) carbon black Printex 90 as benchmark. Based on a pilot study, dose levels were between 0.5 and 162 µg/mouse (0.2 and 8.1 mg/kg bw). Endpoints included pulmonary inflammation (neutrophil numbers in bronchoalveolar fluid), acute phase response, histopathology, and genotoxicity assessed by the comet assay, micronucleus test, and the gamma-H2AX assay. The porous silica materials induced greater pulmonary inflammation than their solid counterparts. A similar pattern was seen for acute phase response induction and histologic changes. This could be explained by a higher specific surface area per mass unit for the most toxic particles. CuO doping further increased the acute phase response normalized according to the deposited surface area. We identified no consistent evidence of synergism between surface area and CuO doping. In conclusion, porosity and CuO doping each increased the toxicity of silica nanomaterials and there was no indication of synergy when the modifications co-occurred.