Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Linking extraction conditions to yield, structure, and techno-functional properties of lupin proteins

  • Taberner-Pibernat, Pau
  • Sabenya, Gerard
  • Ribas-Agustí, Albert
  • Bou, Ricard
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Yellow lupin (Lupinus luteus) is an emerging alternative protein source that is still underutilized in food applications. Consequently, unlike soy and pea, the effects of extraction conditions on lupin protein isolate (LPI) properties remain largely unexplored. This study examined how salt (0.6 M NaCl), heat (80 ¿C, 3 min), and highpH (pH 13) treatments during alkaline solubilization influence LPI yield, composition, structure, and technofunctional properties compared to control conditions (no salt, no heating and pH 10). Salt addition reduced protein yield (¿ 48%) and purity (¿ 13%) by selectively limiting ¿-conglutin extractability, with technofunctional changes driven primarily by compositional rather than structural alterations. Heat treatment was the only extraction condition capable of achieving higher protein yields (+28%) than those under conventional mild extraction conditions, albeit at the expense of reduced purity (¿ 3%). Additionally, despite inducing protein aggregation and decreasing solubility, the heat treatment maintained emulsifying and foaming properties, while improved gelling capacity. Extraction at pH 13 markedly reduced yield (¿ 25%) and purity (¿ 18%) through extensive chemical modifications, without offering recovery advantages over milder conditions, yet emulsifying and foaming performance remained comparable, while gelling improved. Although extraction treatments affected lupin proteins similarly to other legume proteins, the resulting isolates displayed distinctive extraction yield behaviour due to the unique composition of yellow lupin, especially its ¿-conglutin fraction that contributed to the lowest recovery in the salt and high-pH treatments. Overall, these results underscore the importance of tailored extraction strategies to optimize both the extraction process and subsequent food applications., This research was supported by the LUPIPROTECH project (grant PID2020-114422RR-C51), funded by the Spanish Ministry of Science, Innovation and Universities and the State Research Agency (MICIU/AEI/10.13039/501100011033), as well as by the European Union. Additional support was provided by the CERCA Programme of the Government of Catalonia (Generalitat de Catalunya). Pau Taberner-Pibernat received a doctoral contract under grant FI_B 00093 (2022), funded by the Government of Catalonia (Generalitat de Catalunya), and grant FPU22/00656, funded by the Spanish Ministry of Science, Innovation and Universities and the State Research Agency (MICIU/AEI/10.13039/501100011033), with co-funding from the European Social Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhancing lupin protein isolation: Modulation of extraction parameters to maximize protein and phytochemical recovery, and phytase treatment for improved functionality

  • Taberner-Pibernat, Pau
  • Bou, Ricard
  • Castellari, Massimo
  • Trigka, Christina
  • Ribas-Agustí, Albert
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
[EN] The growing demand for plant-based proteins has positioned lupin (Lupinus spp.) as a promising alternative to soy. However, bioactive phytochemicals in lupin seeds ¿although offering valorisation potential¿ pose challenges due to their antinutritional effects and impact on protein functionality. This study investigated how ethanol concentration (EtOH), solvent-to-solute ratio (SSR), and fast heat treatment (HT) using a microwave oven influence the mass yield and composition of lupin protein isolate (LPI), as well as the recovery of phytochemicals in the extraction solvent (ES), using response surface methodology (RSM). Analysis of variance revealed that EtOH and SSR were the most significant factors. The maximum LPI yield was obtained at 11 % EtOH and a 23:1 SSR. Increasing EtOH up to 23 % increased protein content but caused a linear decrease in phytic acid and total phenolic content (TPC) and a linear increase in saponins in LPI, with opposite trends observed in the ES. Increasing SSR reduced LPI protein and phytochemical contents, except for phytic acid, which increased. Conversely, alkaloids, saponins and TPC generally increased with higher SSR in the ES. The addition of phytase during extraction significantly reduced phytic acid levels, improved LPI solubility, and the stability of its emulsifying and foaming properties. However, phytase treatment slightly reduced protein yield and LPI protein content, with changes being statistically significant but of limited practical relevance. These findings demonstrate the importance of tailoring extraction strategies to balance protein yield, content, and phytochemical management, enabling the production of LPI ingredients while facilitating the valorisation of phytochemical-rich side streams., This research was supported by the LUPIPROTECH project, grant PID2020-114422RR-C51, funded by Spanish Ministerio de Ciencia, Innovacion y Universidades and the Agencia Estatal de Investigacion MICIU/AEI/10.13039/501100011033 and by the European Union. Additionally, the CERCA program from the Catalan Government Generalitat de Catalunya. Christina Trigka received the grant PRE2021-099690, funded by the Spanish Ministerio de Ciencia, Innovacion ¿ y Universidades and the Agencia Estatal de Investigacion ¿ MCIN/AEI/10.13039/501100011033 and ESF+. Pau Taberner-Pibernat received the grant FI_B 00093 (2022) doctoral contract grant funded by the Catalan Government Generalitat de Catalunya and the grant FPU22/00656 funded by the Spanish Ministerio de Ciencia, Innovacion ¿ y Universidades and the Agencia Estatal de Investigacion ¿ MICIU/AEI/10.13039/501100011033 and by ESF investing in your future.