Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Ultra High-Capacity Band and Space Division Multiplexing Backbone EONs: Multi-core v.s Multi-fiber

  • Arpanaei, Farhad
  • Ranjbar Zefreh, Mahdi
  • Natalino, Carlos
  • Lechowicz, Piotr
  • Yan, Shuangyi
  • Rivas Moscoso, José Manuel
  • González de Dios, Óscar
  • Fernández Palacios, Juan Pedro
  • Rabbani, Hami
  • Brandt-Pearce, Maïté
  • Sánchez-Macián, Alfonso
  • Hernández Gutiérrez, José Alberto
  • Larrabeiti López, David
  • Monti, Paolo
Both multi-band and space division multiplexing (SDM) independently represent cost-effective approaches for next-generation optical backbone networks, particularly as data exchange between core data centers reaches the petabit-per-second scale. This paper focuses on different strategies for implementing band and SDM elastic optical network (BSDM EON) technology and analyzes the total network capacity of three sizes of backbone metro-core networks: ultra-long-, long-, and medium-distance networks related to the United States, Japan, and Spain, respectively. Two BSDM strategies are considered, namely, multi-core fibers (MCFs) and BSDM based on standard single-mode fiber (SSMF) bundles of multi-fiber pairs (BuMFPs). For MCF-based BSDM, we evaluated the performance of four manufactured trench-assisted weakly coupled (TAWC) MCFs with 4, 7, 13, and 19 cores. Simulation results reveal that, in the regime of ultra-low (UL) loss and inter-core crosstalk (ICXT), MCF-based throughput can be up to 14% higher than SSMF BuMFP-based BSDM when the core pitch exceeds 43 µm and the loss coefficient is lower than that of standard single-mode fibers. However, increasing the number of cores with (non-)standard cladding diameters, UL loss, and ICXT coefficient is not beneficial. As core counts increase up to 13 for non-standard cladding diameters (µ), the core pitch and loss coefficient also increase, leading to degraded performance of MCF-based BSDM compared to SSMF BuMFP-based BSDM. The results indicate that, in scenarios with 19 MFPs, SSFM BuMFP-based BSDM outperforms 19-core MCF-based scenarios, increasing the throughput by 55% to 73%, from medium-backbone networks to ultra-long ones., Farhad Arpanaei acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union’s Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agree-ment No. 801538. The authors would like to acknowledge the support of EU-funded SEASON project (grant No. 101096120), and Spanish-funded Fun4date-Redes project (grant No.PID2022-136684OB-C21).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

A Generalized Cost Model for Techno-Economic Analysis in Optical Networks

  • Souza, André
  • Quagliotti, Marco
  • Hosseini, Mohammad M.
  • Marotta, Andrea
  • Centofanti, Carlo
  • Arpanaei, Farhad
  • Villavicencio Paz, Arantxa
  • Rivas Moscoso, José Manuel
  • Gambari, Gianluca
  • Nadal, Laia
  • Ruiz, Marc
  • Parker, Stephen
  • Pedro, Joao
Techno-economic analysis (TEA) plays a vital role in assessing the feasibility and scalability of emerging technologies, especially in the context of innovation and development. Central to any effective TEA is a reliable and detailed model of capital and operational costs. This paper reports the development of such a model for optical networks in the framework of the SEASON project, aimed at supporting a broad spectrum of techno-economic evaluations. The model is constructed using publicly available data and expert insights from project participants. Its generalizable design allows it to be used both within the SEASON project and as a reference for other studies. By harmonizing assumptions and cost parameters, the model fosters consistency across different analyses. It includes cost and power consumption data for a wide range of commercially available optical network components (including transceivers for point-to-multipoint communications), introduces a statistical framework for estimating values for emerging technologies, and provides a cost model for multiband-doped fiber amplifiers. To demonstrate its practical relevance, the paper applies the model to two case studies: an evaluation of how the cost of various multiband node architectures scales with network traffic in meshed topologies and a comparison of different transport solutions to carry fronthaul flows in the radio access network., This research is supported by the SNS Joint Undertaken—European Union’s Horizon RIA research and innovation programme under grant agreement No. 101096120 (SEASON).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Generating realistic optical topologies for techno-economic studies using MoleNetwork

  • Sánchez-Macián, Alfonso
  • Koneva, Nataliia
  • Quagliotti, Marco
  • Rivas Moscoso, José Manuel
  • Arpanaei, Farhad
  • Hernández Gutiérrez, José Alberto
  • Fernández Palacios, Juan Pedro
Model networks and their underlying topologies have been used as a reference for techno-economic studies for several decades. Existing reference topologies for optical networks may cover different network segments such as backbone, metro core, metro aggregation, access, and/or data center. While telecommunication operators work on the optimization of their own existing deployed optical networks, the availability of different topologies is useful for researchers and technology developers to test their solutions in a variety of scenarios and validate the performance in terms of energy efficiency or cost reduction. This paper presents an open-source tool, MoleNetwork, to generate graphs (backbone, metro core, and metro aggregation) inspired by real network topologies of telecommunication operators that can be used as benchmarks for techno-economic studies. A new topology, to our knowledge, Italy2k, is generated based on the structure of a real operator"s network. Then, the tool is tested by validating that the expected operator parameters are matched in the generated topology and by using the topology to forecast technical demands in a 10-year period in one of its metro regions (core and aggregation networks)., The authors would like to acknowledge the support of EUfunded ALLEGRO (grant No. 101092766) and SEASON (grant No. 101096120) projects, R&D project PID2022-136684OB-C21 (Fun4Date) funded by the Spanish Ministry of Science and Innovation MCIN/AEI/ 10.13039/501100011033 and TUCAN6-CM (TEC- 2024/COM-460), funded by CM (ORDEN 5696/2024)
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

On Designing Transport Networks With Latency Guarantees for Next-Generation Services

  • Koneva, Nataliia
  • Arpanaei, Farhad
  • Sánchez-Macián, Alfonso
  • Hernández Gutiérrez, José Alberto
This article presents an open-source network simulator and digital twin focused on the analysis of latency in Metropolitan Area Networks (MAN). Our tool can estimate delay percentiles between pairs of nodes, aiming to see if the MAN can support emerging services and applications with strict latency requirements. We show that probability bounds like Vysochanskij-Petunin (VP) inequality can be used to accurately estimate latency percentiles between pairs of nodes with minimal computational effort. Theoretical results are validated with extensive simulations leveraging the simmer package, an open-source Discrete Event Simulator (DES) written in R, along with igraph for visualization of networks and shortest path calculations. Two versions of the simulator are provided as open-source on GitHub for the research community to use and build upon: One for local PC and a second one optimized to be executed in the cloud with multiple cores and massive memory., This work was supported by the European Commission, Ministerio de Ciencia e Innovación, Project ITACA (Grant No. PDC2022-133888-I00) funded by Agencia Estatal de Investigación (MCIN, Spain); project SNS project SEASON (Grant No. 101096120) funded by the EU Horizon-Europe Program. This work is also supported by the R&D project PID2022-136684OB-C21 (Fun4Date-Redes) funded by the Spanish Ministry of Science and Innovation MCIN/AEI/10.13039/501100011033.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Digital twin-assisted lightpath provisioning and nonlinear mitigation in C+L+S multiband optical networks

  • Ghasrizadeh Dezfouli, Mohammad Sadegh
  • Khare, Prasunika
  • Costa, Nelson
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
  • Napoli, Antonio
  • Pedro, João|||0000-0003-4471-7401
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
Multiband (MB) optical transmission targets increasing the capacity of operators’ optical transport networks. However, nonlinear impairments (NLI) affect each optical channel in the C+L+S bands differently, and, therefore, the routing and spectrum assignment (RSA) problem needs to be complemented with fast and accurate tools to consider the quality of transmission (QoT) within the provisioning process. This paper proposes a digital twin-assisted approach for lightpath provisioning to provide a complete solution for the RSA problem that ensures the required QoT in MB optical networks. The OCATA time domain digital twin is proposed, not only to estimate the QoT of a selected path but also to support the QoT-based channel assignment process. OCATA is based on a Deep Neural Network (DNN) to model the propagation of the optical signal. However, because of the different impacts of nonlinear noise on each channel and the large number of channels that need to be considered in C+L+S MB scenarios, OCATA needs to be adapted to make it scalable, while keeping its high accuracy and fast QoT estimation characteristics. In consequence, a complete methodology is proposed in this work that limits the number of channels being modeled to just a few. Moreover, OCATA-MB helps to mitigate NLI noise by programming the receiver at the provisioning time and thus with very little complexity compared to its equivalent implemented during the operation. NLI noise mitigation can be applied in the case when a lightpath cannot be provisioned because none of the available channels can provide the required QoT, making it an advantageous tool for reducing connection blocking. Exhaustive simulation results demonstrate the remarkable accuracy of OCATA-MB in estimating the QoT for any channel. Interestingly, by utilizing the proposed OCATA-MB-assisted lightpath provisioning approach, a reduction of the blocking ratio exceeding 50% when compared to traditional approaches is shown when NLI noise mitigation is not applied. If NLI mitigation is implemented, an additional over 50% blocking reduction is achieved., The research leading to these results has received funding from the European Commission MSCA-DN NESTOR (G.A. 101119983) and MSCA-EID MENTOR (G.A. 956713), from the SNS JU under the European Union’s Horizon Europe SEASON (G.A. 101096120), and from the ICREA Institution., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Context-based e2e autonomous operation in B5G networks

  • Wang, Shaoxuan
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
The research and innovation related to fifth-generation (5G) networks that has been carried out in recent years has decided on the fundamentals of the smart slice in radio access networks (RANs), as well as the autonomous fixed network operation. One of the most challenging objectives of beyond 5G (B5G) and sixth-generation (6G) networks is the deployment of mechanisms that enable smart end-to-end (e2e) network operation, which is required for the achievement of the stringent service requirements of the envisioned use cases to be supported in the short term. Therefore, smart actions, such as dynamic capacity allocation, flexible functional split, and dynamic slice management need to be performed in tight coordination with the autonomous capacity management of the fixed transport network infrastructure. Otherwise, the benefits of smart slice operation (i.e., cost and energy savings while ensuring per-slice service requirements) might be cancelled due to uncoordinated autonomous fixed network operation. Notably, the transport network in charge of supporting slices from the user equipment (UE) to the core expands across access and metro fixed networks. The required coordination needs to be performed while keeping the privacy of the radio and fixed network domains, which is important in multi-tenant scenarios where both network segments are managed by different operators. In this paper, we propose a novel approach that explores the concept of context-aware network operation, where the slice control anticipates the aggregated and anonymized information of the expected slice operation that is sent to the fixed network orchestrator in an asynchronous way. The context is then used as the input for the artificial intelligence (AI)-based models used by the fixed network control for the predictive capacity management of optical connections in support of RAN slices. This context-aware network operation aims at enabling accurate and reliable autonomous fixed network operation under extremely dynamic traffic originated by smart RAN operation. The exhaustive numerical results show that slice context availability improves the benchmarking fixed network predictive methods (90% reduction in prediction maximum error) remarkably in the foreseen B5G scenarios, for both access and metro segments and in heterogeneous service demand scenarios. Moreover, context-aware network operation enables robust and efficient operation of optical networks in support of dense RAN cells (>32 base stations per cell), while the benchmarking methods fail to guarantee different operational objectives., This work is partially supported by the SNS Joint Undertaken under grant agreement No. 101096120 (SEASON), the MICINN IBON (PID2020-114135RB-I00) project, and from the ICREA Institution., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Twining digital subcarrier multiplexed optical signals with OCATA for lightpath provisioning

  • Devigili, Mariano|||0000-0003-0613-5195
  • Sequeira, Diogo Gonçalo
  • Torres Ferrera, Pablo
  • Srivallapanondh, Sasipim
  • Costa, Nelson
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
  • Castro, Carlos|||0000-0003-2411-2907
  • Napoli, Antonio
  • Pedro, João|||0000-0003-4471-7401
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
Digital Twins (DT) are needed in elastic optical networks to enable further advance and pave the way towards autonomous networks. Dynamical models self-adjusting with their physical counterpart have to maintain low computational complexity and guarantee good accuracy, regardless of the network topology and the technology supporting the optical lightpath. In this work, we propose data-driven models based on cascaded learning for single carrier signal as well as digital subcarrier multiplexing signals. Firstly, we explore the potentials of such a DT by proposing an algorithm for lightpath provisioning. In addition, the performances of the proposed models are compared with the ones of analytical models. Secondly, we experimentally evaluate its accuracy to predict the impact of optical filtering penalties. The simulations show an overall good accuracy for different signal formats and demonstrate their viability for lightpath provisioning. Similarly, the experimental results demonstrate the feasibility of implementing such models to estimate the quality of transmission for digital subcarrier multiplexed signals., The research leading to these results has received funding from the European Community through the MSCA MENTOR (G.A. 956713), the European Union's Horizon Europe research and innovation programme SEASON (G.A. 101096120), the MICINN IBON (PID2020-114135RB-I00) and from the ICREA Institution., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Traffic-aware ONU grouping and downstream bandwidth allocation for multicast services in flexible-rate PONs

  • Lu, Xiang
  • Wei, Xinshui
  • Zhong, Zhiyuan
  • Li, Jun
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
In flexible-rate passive optical networks (PONs), optical network units (ONUs) with different channel conditions can achieve different data rates by implementing flexible transmission parameters, e.g., modulation format, thereby enhancing system capacity. Correspondingly, the downstream frame is divided into multiple subframes, each being received and processed only by ONUs in its targeted group. However, for downstream multicast services, the data need to be duplicated and encapsulated into multiple subframes for ONUs belonging to different groups, resulting in data redundancy and degradation of effective throughput (i.e., throughput without redundant data). To improve resource utilization, ONU grouping should be dynamically adjusted according to both channel conditions and time-varying network factors, e.g., traffic loads and multicast memberships. For this, we first enhance the current downstream scheduling protocol to support dynamic ONU grouping in a multicast scenario and propose a traffic-aware ONU grouping (TAOG) algorithm to improve effective throughput, which optimizes ONU grouping by considering time-varying network conditions. As ONUs belonging to different groups have different data rates, we further propose a group-based downstream time slot allocation (GBDTA) algorithm to adjust time slots for each service by considering their demands and ONU data rates. Exhaustive simulation results show that the integrated TAOG-GBDTA scheme adapts effectively to dynamic network conditions and, compared to conventional schemes, it effectively improves effective throughput, reduces redundancy, and achieves lower packet latency under various multicast scenarios., Leading Youth Talents of Innovation and Entrepreneurship of Gusu (ZXL2023162); European Commission MSCA-DN NESTOR (G.A.101119983); HORIZON EUROPE Framework Programme SEASON (G.A. 101096120); ICREA Institution., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Near-real-time 6G service operation enabled by distributed intelligence and in-band telemetry

  • González Pacheco, Pol|||0000-0003-4751-2380
  • Alhamed, Faris
  • Shakespear Miles, Hailey Josephine|||0000-0002-0845-474X
  • Barzegar, Sima|||0000-0003-1916-7217
  • Paolucci, Francesco
  • Sgambelluri, Andrea
  • Vegas Olmos, Juan J.
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
The combination of highly dynamic network services requiring stringent quality of service (QoS), especially in terms of end-to-end (e2e) delay, together with capital and operational cost reduction cannot be faced using centralized software-defined networking (SDN) solutions only. In particular, such expected dynamicity requires autonomous near-real-time operation fed with pervasive telemetry to make per-service decisions that ensure the committed QoS, while reducing overprovisioning as much as possible. In this paper, we propose a distributed control architecture based on multi-agent systems (MASs) to assist the SDN controller in the control of network services near-real-time. Per-traffic flow telemetry data are collected from the packet nodes, distributed through the agents in the control plane, and analyzed to assure performance and to anticipate any degradation. Measurements feed flow agents, which are based on deep reinforcement learning (DRL) models, to make routing decisions aiming at ensuring flow performance. In the case when QoS degradation is detected, we propose algorithms to analyze its cause, which can be a result of some bottleneck in the network. We show how the latter is detected and additional capacity is requested of the SDN controller, which in turn creates an optical bypass to provide additional capacity. The proposed solution is demonstrated experimentally on a federated testbed connecting UPC and CNIT premises. Focused first on the control plane, the feasibility of the proposed architecture and workflows is experimentally assessed. After that, the performance of the near-real-time operation is evaluated at the data plane to verify that the maximum e2e delay is not exceeded for multiple flows, showing the effectiveness of predictive QoS evaluation together with infrastructure and service reconfiguration., The research leading to these results has received funding from the SNS JU under the European Union's Horizon Europe research and innovation programme under Grant Agreement No. 101096120 (SEASON) and from the ICREA Institution., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Distributed intelligence for pervasive optical network telemetry

  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
  • González Pacheco, Pol|||0000-0003-4751-2380
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
Optical network automation and failure management require measuring the status and the performance of the different network devices to anticipate any degradation and ensure the quality of the provided services, i.e., optical connectivity. Such pervasive network telemetry entails collecting large amounts of measurements and events from different sources and with very fine granularity, which given the amount and variety of telemetry sources and the size of each measurement and event, imposes requirements that are hard to achieve without large investments. In this paper, we analyze the main limitations of telemetry architectures relying exclusively on centralized systems for data analysis and propose an architecture with distributed intelligence. Data aggregation techniques, especially conceived for optical network telemetry, are presented with the objective of reducing data dimensionality. Illustrative results from our experimental telemetry system reveal a reduction of 3 orders of magnitude in terms of total data volume without introducing significant error and processing delay and, more importantly, helping network automation algorithms to identify meaningful changes in the network status., HORIZON EUROPE Framework Programme [SEASON (101096120)]; Agencia Estatal de Investigación [IBON (PID2020-114135RB-I00)]; Institució Catalana de Recerca i Estudis Avançats., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Applications of the OCATA time domain digital twin: from QoT estimation to failure management

  • Devigili, Mariano|||0000-0003-0613-5195
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
  • Costa, Nelson
  • Castro, Carlos|||0000-0003-2411-2907
  • Napoli, Antonio
  • Pedro, João|||0000-0003-4471-7401
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
Optical in-phase and quadrature (IQ) constellations enclose valuable information regarding the optical elements traversed by the optical signal. Such information can be extracted and exploited by algorithms and models within an optical layer digital twin. In this paper, we investigate the feasibility of extracting information from IQ constellations and its use for both accurate quality of transmission (QoT) estimation and efficient failure management within. First, we observe the correlations between the measured QoT of lightpaths and the value of specific features extracted from IQ constellation samples collected from the optical receiver and design deep neural network (DNN) models for QoT estimation. Next, specific DNN models and algorithms that exploit IQ constellation features are proposed for soft-failure detection, identification, and severity estimation. Results from both simulation and experiments show noticeable accuracy on the estimation of QoT and on the prediction of failures affecting the transmitter, optical filters, and amplifiers., HORIZON EUROPE Framework Programme [SEASON (101096120)]; Horizon 2020 Framework Programme [MSCA-EID MENTOR (956713)]; Ministerio de Ciencia e Innovación [IBON (PID2020-114135RB-I00)]; Institució Catalana de Recerca i Estudis Avançats., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Centralized and distributed approaches to control optical point-to-multipoint systems near-real-time

  • Shakespear Miles, Hailey Josephine|||0000-0002-0845-474X
  • Lin, Q.
  • Barzegar, Sima|||0000-0003-1916-7217
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
  • Chen, X.
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
Optical point-to-multipoint (P2MP) connectivity based on digital subcarrier multiplexing (DSCM) has been shown as a solution for the metro-access segment that is able to reduce capital and operational costs and support the capacity and high dynamicity needs of future 6G services. To achieve maximum performance, activation and deactivation of subcarriers must be done near-real-time to provide just the capacity needed to support the input traffic. In this paper, we investigate the applicability of various approaches capable of supporting the near-real-time operation requirement. Starting from the centralized approach that can be carried out on the centralized software-defined networking (SDN) controller, we also explore distributed approaches that might relieve the SDN controller from near-real-time operation. In particular, we explore the performance of deploying a multiagent system (MAS), where intelligent agents run on top of the nodes in the P2MP tree and communicate among them. Illustrative results show that the distributed approaches can achieve a performance close to that of the centralized one, while reducing communication needs. Results also show the importance of traffic/capacity prediction to anticipate the activation of subcarriers., The research leading to these results has received funding from the Smart Networks and Services Joint Undertaking under the European Union's Horizon Europe research and innovation programme under Grant Agreement No. 101096120 (SEASON), the MICINN IBON (PID2020-114135RB-I00) project and from the ICREA Institution., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Simulation and modelling of C+L+S multiband optical transmission for the OCATA time domain digital twin

  • Khare, Prasunika
  • Costa, Nelson
  • Ruiz Ramírez, Marc|||0000-0001-6429-6347
  • Napoli, Antonio
  • Comellas Colomé, Jaume|||0000-0002-9129-0562
  • Pedro, João|||0000-0003-4471-7401
  • Velasco Esteban, Luis Domingo|||0000-0002-7345-296X
This paper is an extended version of our published paper: Khare, P.; Costa, N.; Pedro, J.; Napoli, A.; Arpanaei, F.; Comellas, J.; Ruiz, M.; Velasco, L. SSMS: A Split Step MultiBand Simulation Software. In Proceedings of the IEEE International Conference on Transparent Optical Networks (ICTON), Bucharest, Romania, 2–6 July 2023., C+L+S multiband (MB) optical transmission has the potential to increase the capacity of optical transport networks, and thus, it is a possible solution to cope with the traffic increase expected in the years to come. However, the introduction of MB optical technology needs to come together with the needed tools that support network planning and operation. In particular, quality of transmission (QoT) estimation is needed for provisioning optical MB connections. In this paper, we concentrate on modelling MB optical transmission for provide fast and accurate QoT estimation and propose machine learning (ML) approaches based on neural networks, which can be easily integrated into an optical layer digital twin (DT) solution. We start by considering approaches that can be used for accurate signal propagation modelling. Even though solutions such as the split-step Fourier method (SSFM) for solving the nonlinear Schrödinger equation (NLSE) have limited application for QoT estimation during provisioning because of their very high complexity and time consumption, they could be used to generate datasets for ML model creation. However, even that can be hard to carry out on a fully loaded MB system with hundreds of channels. In addition, in MB optical transmission, interchannel stimulated Raman scattering (ISRS) becomes a major effect, which adds more complexity. In view of that, the fourth-order Runge–Kutta in the interaction picture (RK4IP) method, complemented with an adaptive step size algorithm to further reduce the computation time, is evaluated as an alternative to reduce time complexity. We show that RK4IP provided an accuracy comparable to that of the SSFM with reduced computation time, which enables its application for MB optical transmission simulation. Once datasets were generated using the adaptive step size RK4IP method, two ML modelling approaches were considered to be integrated in the OCATA DT, where models predict optical signal propagation in the time domain. Being able to predict the optical signal in the time domain, as it will be received after propagation, opens opportunities for automating network operation, including connection provisioning and failure management. In this paper, we focus on comparing the proposed ML modelling approaches in terms of the models’ general and QoT estimation accuracy., The research leading to these results has received funding from the European Commission MSCA-EID MENTOR (G.A. 956713), from the SNS JU under the European Union’s Horizon Europe SEASON (G.A. 101096120), and from the ICREA Institution., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Applications of the OCATA time domain digital twin: from QoT estimation to failure management

  • Devigili, Mariano
  • Ruiz Ramírez, Marc
  • Costa, Nelson
  • Castro, Carlos
  • Napoli, Antonio
  • Pedro, João
  • Velasco Esteban, Luis Domingo
Optical in-phase and quadrature (IQ) constellations enclose valuable information regarding the optical elements traversed by the optical signal. Such information can be extracted and exploited by algorithms and models within an optical layer digital twin. In this paper, we investigate the feasibility of extracting information from IQ constellations and its use for both accurate quality of transmission (QoT) estimation and efficient failure management within. First, we observe the correlations between the measured QoT of lightpaths and the value of specific features extracted from IQ constellation samples collected from the optical receiver and design deep neural network (DNN) models for QoT estimation. Next, specific DNN models and algorithms that exploit IQ constellation features are proposed for soft-failure detection, identification, and severity estimation. Results from both simulation and experiments show noticeable accuracy on the estimation of QoT and on the prediction of failures affecting the transmitter, optical filters, and amplifiers., HORIZON EUROPE Framework Programme [SEASON (101096120)]; Horizon 2020 Framework Programme [MSCA-EID MENTOR (956713)]; Ministerio de Ciencia e Innovación [IBON (PID2020-114135RB-I00)]; Institució Catalana de Recerca i Estudis Avançats., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Twining digital subcarrier multiplexed optical signals with OCATA for lightpath provisioning

  • Devigili, Mariano
  • Sequeira, Diogo Gonçalo
  • Torres Ferrera, Pablo
  • Srivallapanondh, Sasipim
  • Costa, Nelson
  • Ruiz Ramírez, Marc
  • Castro, Carlos
  • Napoli, Antonio
  • Pedro, João
  • Velasco Esteban, Luis Domingo
Digital Twins (DT) are needed in elastic optical networks to enable further advance and pave the way towards autonomous networks. Dynamical models self-adjusting with their physical counterpart have to maintain low computational complexity and guarantee good accuracy, regardless of the network topology and the technology supporting the optical lightpath. In this work, we propose data-driven models based on cascaded learning for single carrier signal as well as digital subcarrier multiplexing signals. Firstly, we explore the potentials of such a DT by proposing an algorithm for lightpath provisioning. In addition, the performances of the proposed models are compared with the ones of analytical models. Secondly, we experimentally evaluate its accuracy to predict the impact of optical filtering penalties. The simulations show an overall good accuracy for different signal formats and demonstrate their viability for lightpath provisioning. Similarly, the experimental results demonstrate the feasibility of implementing such models to estimate the quality of transmission for digital subcarrier multiplexed signals., The research leading to these results has received funding from the European Community through the MSCA MENTOR (G.A. 956713), the European Union's Horizon Europe research and innovation programme SEASON (G.A. 101096120), the MICINN IBON (PID2020-114135RB-I00) and from the ICREA Institution., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Near-real-time 6G service operation enabled by distributed intelligence and in-band telemetry

  • González Pacheco, Pol
  • Alhamed, Faris
  • Shakespear Miles, Hailey Josephine
  • Barzegar, Sima
  • Paolucci, Francesco
  • Sgambelluri, Andrea
  • Vegas Olmos, Juan J.
  • Ruiz Ramírez, Marc
  • Velasco Esteban, Luis Domingo
The combination of highly dynamic network services requiring stringent quality of service (QoS), especially in terms of end-to-end (e2e) delay, together with capital and operational cost reduction cannot be faced using centralized software-defined networking (SDN) solutions only. In particular, such expected dynamicity requires autonomous near-real-time operation fed with pervasive telemetry to make per-service decisions that ensure the committed QoS, while reducing overprovisioning as much as possible. In this paper, we propose a distributed control architecture based on multi-agent systems (MASs) to assist the SDN controller in the control of network services near-real-time. Per-traffic flow telemetry data are collected from the packet nodes, distributed through the agents in the control plane, and analyzed to assure performance and to anticipate any degradation. Measurements feed flow agents, which are based on deep reinforcement learning (DRL) models, to make routing decisions aiming at ensuring flow performance. In the case when QoS degradation is detected, we propose algorithms to analyze its cause, which can be a result of some bottleneck in the network. We show how the latter is detected and additional capacity is requested of the SDN controller, which in turn creates an optical bypass to provide additional capacity. The proposed solution is demonstrated experimentally on a federated testbed connecting UPC and CNIT premises. Focused first on the control plane, the feasibility of the proposed architecture and workflows is experimentally assessed. After that, the performance of the near-real-time operation is evaluated at the data plane to verify that the maximum e2e delay is not exceeded for multiple flows, showing the effectiveness of predictive QoS evaluation together with infrastructure and service reconfiguration., The research leading to these results has received funding from the SNS JU under the European Union's Horizon Europe research and innovation programme under Grant Agreement No. 101096120 (SEASON) and from the ICREA Institution., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Traffic-aware ONU grouping and downstream bandwidth allocation for multicast services in flexible-rate PONs

  • Lu, Xiang
  • Wei, Xinshui
  • Zhong, Zhiyuan
  • Li, Jun
  • Velasco Esteban, Luis Domingo
In flexible-rate passive optical networks (PONs), optical network units (ONUs) with different channel conditions can achieve different data rates by implementing flexible transmission parameters, e.g., modulation format, thereby enhancing system capacity. Correspondingly, the downstream frame is divided into multiple subframes, each being received and processed only by ONUs in its targeted group. However, for downstream multicast services, the data need to be duplicated and encapsulated into multiple subframes for ONUs belonging to different groups, resulting in data redundancy and degradation of effective throughput (i.e., throughput without redundant data). To improve resource utilization, ONU grouping should be dynamically adjusted according to both channel conditions and time-varying network factors, e.g., traffic loads and multicast memberships. For this, we first enhance the current downstream scheduling protocol to support dynamic ONU grouping in a multicast scenario and propose a traffic-aware ONU grouping (TAOG) algorithm to improve effective throughput, which optimizes ONU grouping by considering time-varying network conditions. As ONUs belonging to different groups have different data rates, we further propose a group-based downstream time slot allocation (GBDTA) algorithm to adjust time slots for each service by considering their demands and ONU data rates. Exhaustive simulation results show that the integrated TAOG-GBDTA scheme adapts effectively to dynamic network conditions and, compared to conventional schemes, it effectively improves effective throughput, reduces redundancy, and achieves lower packet latency under various multicast scenarios., Leading Youth Talents of Innovation and Entrepreneurship of Gusu (ZXL2023162); European Commission MSCA-DN NESTOR (G.A.101119983); HORIZON EUROPE Framework Programme SEASON (G.A. 101096120); ICREA Institution., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Digital twin-assisted lightpath provisioning and nonlinear mitigation in C+L+S multiband optical networks

  • Ghasrizadeh Dezfouli, Mohammad Sadegh
  • Khare, Prasunika
  • Costa, Nelson
  • Ruiz Ramírez, Marc
  • Napoli, Antonio
  • Pedro, João
  • Velasco Esteban, Luis Domingo
Multiband (MB) optical transmission targets increasing the capacity of operators’ optical transport networks. However, nonlinear impairments (NLI) affect each optical channel in the C+L+S bands differently, and, therefore, the routing and spectrum assignment (RSA) problem needs to be complemented with fast and accurate tools to consider the quality of transmission (QoT) within the provisioning process. This paper proposes a digital twin-assisted approach for lightpath provisioning to provide a complete solution for the RSA problem that ensures the required QoT in MB optical networks. The OCATA time domain digital twin is proposed, not only to estimate the QoT of a selected path but also to support the QoT-based channel assignment process. OCATA is based on a Deep Neural Network (DNN) to model the propagation of the optical signal. However, because of the different impacts of nonlinear noise on each channel and the large number of channels that need to be considered in C+L+S MB scenarios, OCATA needs to be adapted to make it scalable, while keeping its high accuracy and fast QoT estimation characteristics. In consequence, a complete methodology is proposed in this work that limits the number of channels being modeled to just a few. Moreover, OCATA-MB helps to mitigate NLI noise by programming the receiver at the provisioning time and thus with very little complexity compared to its equivalent implemented during the operation. NLI noise mitigation can be applied in the case when a lightpath cannot be provisioned because none of the available channels can provide the required QoT, making it an advantageous tool for reducing connection blocking. Exhaustive simulation results demonstrate the remarkable accuracy of OCATA-MB in estimating the QoT for any channel. Interestingly, by utilizing the proposed OCATA-MB-assisted lightpath provisioning approach, a reduction of the blocking ratio exceeding 50% when compared to traditional approaches is shown when NLI noise mitigation is not applied. If NLI mitigation is implemented, an additional over 50% blocking reduction is achieved., The research leading to these results has received funding from the European Commission MSCA-DN NESTOR (G.A. 101119983) and MSCA-EID MENTOR (G.A. 956713), from the SNS JU under the European Union’s Horizon Europe SEASON (G.A. 101096120), and from the ICREA Institution., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Distributed intelligence for pervasive optical network telemetry

  • Velasco Esteban, Luis Domingo
  • González Pacheco, Pol
  • Ruiz Ramírez, Marc
Optical network automation and failure management require measuring the status and the performance of the different network devices to anticipate any degradation and ensure the quality of the provided services, i.e., optical connectivity. Such pervasive network telemetry entails collecting large amounts of measurements and events from different sources and with very fine granularity, which given the amount and variety of telemetry sources and the size of each measurement and event, imposes requirements that are hard to achieve without large investments. In this paper, we analyze the main limitations of telemetry architectures relying exclusively on centralized systems for data analysis and propose an architecture with distributed intelligence. Data aggregation techniques, especially conceived for optical network telemetry, are presented with the objective of reducing data dimensionality. Illustrative results from our experimental telemetry system reveal a reduction of 3 orders of magnitude in terms of total data volume without introducing significant error and processing delay and, more importantly, helping network automation algorithms to identify meaningful changes in the network status., HORIZON EUROPE Framework Programme [SEASON (101096120)]; Agencia Estatal de Investigación [IBON (PID2020-114135RB-I00)]; Institució Catalana de Recerca i Estudis Avançats., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Context-based e2e autonomous operation in B5G networks

  • Wang, Shaoxuan
  • Ruiz Ramírez, Marc
  • Velasco Esteban, Luis Domingo
The research and innovation related to fifth-generation (5G) networks that has been carried out in recent years has decided on the fundamentals of the smart slice in radio access networks (RANs), as well as the autonomous fixed network operation. One of the most challenging objectives of beyond 5G (B5G) and sixth-generation (6G) networks is the deployment of mechanisms that enable smart end-to-end (e2e) network operation, which is required for the achievement of the stringent service requirements of the envisioned use cases to be supported in the short term. Therefore, smart actions, such as dynamic capacity allocation, flexible functional split, and dynamic slice management need to be performed in tight coordination with the autonomous capacity management of the fixed transport network infrastructure. Otherwise, the benefits of smart slice operation (i.e., cost and energy savings while ensuring per-slice service requirements) might be cancelled due to uncoordinated autonomous fixed network operation. Notably, the transport network in charge of supporting slices from the user equipment (UE) to the core expands across access and metro fixed networks. The required coordination needs to be performed while keeping the privacy of the radio and fixed network domains, which is important in multi-tenant scenarios where both network segments are managed by different operators. In this paper, we propose a novel approach that explores the concept of context-aware network operation, where the slice control anticipates the aggregated and anonymized information of the expected slice operation that is sent to the fixed network orchestrator in an asynchronous way. The context is then used as the input for the artificial intelligence (AI)-based models used by the fixed network control for the predictive capacity management of optical connections in support of RAN slices. This context-aware network operation aims at enabling accurate and reliable autonomous fixed network operation under extremely dynamic traffic originated by smart RAN operation. The exhaustive numerical results show that slice context availability improves the benchmarking fixed network predictive methods (90% reduction in prediction maximum error) remarkably in the foreseen B5G scenarios, for both access and metro segments and in heterogeneous service demand scenarios. Moreover, context-aware network operation enables robust and efficient operation of optical networks in support of dense RAN cells (>32 base stations per cell), while the benchmarking methods fail to guarantee different operational objectives., This work is partially supported by the SNS Joint Undertaken under grant agreement No. 101096120 (SEASON), the MICINN IBON (PID2020-114135RB-I00) project, and from the ICREA Institution., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Simulation and modelling of C+L+S multiband optical transmission for the OCATA time domain digital twin

  • Khare, Prasunika
  • Costa, Nelson
  • Ruiz Ramírez, Marc
  • Napoli, Antonio
  • Comellas Colomé, Jaume
  • Pedro, João
  • Velasco Esteban, Luis Domingo
This paper is an extended version of our published paper: Khare, P.; Costa, N.; Pedro, J.; Napoli, A.; Arpanaei, F.; Comellas, J.; Ruiz, M.; Velasco, L. SSMS: A Split Step MultiBand Simulation Software. In Proceedings of the IEEE International Conference on Transparent Optical Networks (ICTON), Bucharest, Romania, 2–6 July 2023., C+L+S multiband (MB) optical transmission has the potential to increase the capacity of optical transport networks, and thus, it is a possible solution to cope with the traffic increase expected in the years to come. However, the introduction of MB optical technology needs to come together with the needed tools that support network planning and operation. In particular, quality of transmission (QoT) estimation is needed for provisioning optical MB connections. In this paper, we concentrate on modelling MB optical transmission for provide fast and accurate QoT estimation and propose machine learning (ML) approaches based on neural networks, which can be easily integrated into an optical layer digital twin (DT) solution. We start by considering approaches that can be used for accurate signal propagation modelling. Even though solutions such as the split-step Fourier method (SSFM) for solving the nonlinear Schrödinger equation (NLSE) have limited application for QoT estimation during provisioning because of their very high complexity and time consumption, they could be used to generate datasets for ML model creation. However, even that can be hard to carry out on a fully loaded MB system with hundreds of channels. In addition, in MB optical transmission, interchannel stimulated Raman scattering (ISRS) becomes a major effect, which adds more complexity. In view of that, the fourth-order Runge–Kutta in the interaction picture (RK4IP) method, complemented with an adaptive step size algorithm to further reduce the computation time, is evaluated as an alternative to reduce time complexity. We show that RK4IP provided an accuracy comparable to that of the SSFM with reduced computation time, which enables its application for MB optical transmission simulation. Once datasets were generated using the adaptive step size RK4IP method, two ML modelling approaches were considered to be integrated in the OCATA DT, where models predict optical signal propagation in the time domain. Being able to predict the optical signal in the time domain, as it will be received after propagation, opens opportunities for automating network operation, including connection provisioning and failure management. In this paper, we focus on comparing the proposed ML modelling approaches in terms of the models’ general and QoT estimation accuracy., The research leading to these results has received funding from the European Commission MSCA-EID MENTOR (G.A. 956713), from the SNS JU under the European Union’s Horizon Europe SEASON (G.A. 101096120), and from the ICREA Institution., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Centralized and distributed approaches to control optical point-to-multipoint systems near-real-time

  • Shakespear Miles, Hailey Josephine
  • Lin, Q.
  • Barzegar, Sima
  • Ruiz Ramírez, Marc
  • Chen, X.
  • Velasco Esteban, Luis Domingo
Optical point-to-multipoint (P2MP) connectivity based on digital subcarrier multiplexing (DSCM) has been shown as a solution for the metro-access segment that is able to reduce capital and operational costs and support the capacity and high dynamicity needs of future 6G services. To achieve maximum performance, activation and deactivation of subcarriers must be done near-real-time to provide just the capacity needed to support the input traffic. In this paper, we investigate the applicability of various approaches capable of supporting the near-real-time operation requirement. Starting from the centralized approach that can be carried out on the centralized software-defined networking (SDN) controller, we also explore distributed approaches that might relieve the SDN controller from near-real-time operation. In particular, we explore the performance of deploying a multiagent system (MAS), where intelligent agents run on top of the nodes in the P2MP tree and communicate among them. Illustrative results show that the distributed approaches can achieve a performance close to that of the centralized one, while reducing communication needs. Results also show the importance of traffic/capacity prediction to anticipate the activation of subcarriers., The research leading to these results has received funding from the Smart Networks and Services Joint Undertaking under the European Union's Horizon Europe research and innovation programme under Grant Agreement No. 101096120 (SEASON), the MICINN IBON (PID2020-114135RB-I00) project and from the ICREA Institution., Peer Reviewed, Postprint (author's final draft)