Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Semianalytical Solution for CO2 Plume Shape and Pressure Evolution During CO2 Injection in Deep Saline Formations

  • Vilarrasa, Víctor
  • Carrera, Jesús
  • Bolster, Diogo
  • Dentz, Marco
The injection of supercritical carbon dioxide (CO2) in deep saline aquifers leads to the formation of a CO2 rich phase plume that tends to float over the resident brine. As pressure builds up, CO2 density will increase because of its high compressibility. Current analytical solutions do not account for CO2 compressibility and consider a volumetric injection rate that is uniformly distributed along the whole thickness of the aquifer, which is unrealistic. Furthermore, the slope of the CO2 pressure with respect to the logarithm of distance obtained from these solutions differs from that of numerical solutions. We develop a semianalytical solution for the CO2 plume geometry and fluid pressure evolution, accounting for CO2 compressibility and buoyancy effects in the injection well, so CO2 is not uniformly injected along the aquifer thickness. We formulate the problem in terms of a CO2 potential that facilitates solution in horizontal layers, with which we discretize the aquifer. Capillary pressure is considered at the interface between the CO2 rich phase and the aqueous phase. When a prescribed CO2 mass flow rate is injected, CO2 advances initially through the top portion of the aquifer. As CO2 is being injected, the CO2 plume advances not only laterally, but also vertically downwards. However, the CO2 plume does not necessarily occupy the whole thickness of the aquifer. We found that even in the cases in which the CO2 plume reaches the bottom of the aquifer, most of the injected CO2 enters the aquifer through the layers at the top. Both CO2 plume position and fluid pressure compare well with numerical simulations. This solution permits quick evaluations of the CO2 plume position and fluid pressure distribution when injecting supercritical CO2 in a deep saline aquifer. © 2013 Springer Science+Business Media Dordrecht., This work has been funded by Fundación Ciudad de la Energía (Spanish Government) (www.ciuden.es) and 35 by the European Union through the “European Energy Programme for Recovery” and the Compostilla OXYCFB300 project. We also want to acknowledge the financial support received from the ‘MUSTANG’ (www.co2mustang.eu) and ‘PANACEA’ (www.panacea-co2.org) projects (from the European Community’s Seventh Framework Programme FP7/2007-2013 under grant agreements nº 227286 and nº 282900, respectively)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Liquid CO2 injection for geological storage in deep saline aquifers

  • Vilarrasa, Víctor
  • Silva, Orlando
  • Carrera, Jesús
  • Olivella, Sebastià
CO2 will remain in supercritical (SC) state (i.e. p>7.382MPa and T>31.04°C) under the pressure (p) and temperature (T) conditions appropriate for geological storage. Thus, it is usually assumed that CO2 will reach the aquifer in SC conditions. However, inflowing CO2 does not need to be in thermal equilibrium with the aquifer. In fact, surface operations are simpler for liquid than for SC CO2, because CO2 is transported in liquid state. Yet, problems might arise because of thermal stresses induced by cold CO2 injection and because of phase changes in the injection tubing or in the formation. Here, we propose liquid CO2 injection and analyze its evolution and the thermo-hydro-mechanical response of the formation and the caprock. We find that injecting CO2 in liquid state is energetically more efficient than in SC state because liquid CO2 is denser than SC CO2, leading to a lower overpressure not only at the wellhead, but also in the reservoir because a smaller fluid volume is displaced. Cold CO2 injection cools down the formation around the injection well. Further away, CO2 equilibrates thermally with the medium in an abrupt front. The liquid CO2 region close to the injection well advances far behind the SC CO2 interface. While the SC CO2 region is dominated by gravity override, the liquid CO2 region displays a steeper front because viscous forces dominate (liquid CO2 is not only denser, but also more viscous than SC CO2). The temperature decrease close to the injection well induces a stress reduction due to thermal contraction of the media. This can lead to shear slip of pre-existing fractures in the aquifer for large temperature contrasts in stiff rocks, which could enhance injectivity. In contrast, the mechanical stability of the caprock is improved in stress regimes where the maximum principal stress is the vertical. © 2013 Elsevier Ltd., V.V. wishes to acknowledge the Spanish Ministry of Science and Innovation (MCI), through the “Formación de Profesorado Universitario” Program, and the “Colegio de Ingenieros de Caminos, Canales y Puertos – Catalunya” for their financial support. This work has been funded by Fundación Ciudad de la Energía (Spanish Government) (www.ciuden.es) through the project ALM/09/018 and by the European Union through the “European Energy Programme for Recovery” and the Compostilla OXYCFB300 project. We also want to acknowledge the financial support received from the ‘MUSTANG’ (www.co2mustang.eu) and ‘PANACEA’ (www.panacea-co2.org) projects (from the European Community's Seventh Framework Programme FP7/2007–2013 under grant agreements nos. 227286 and 282900, respectively)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Calcite interaction with acidic sulphate solutions: a vertical scanning interferometry and energy-dispersive XRF study

  • Atanassova, Radostina
  • Cama, Jordi
  • Soler, Josep M.
  • Offeddu, Francesco G.
  • Queralt Mitjans, Ignacio
  • Casanova, Ignasi
Calcite dissolution on (10 (1) over bar4) cleavage surface was investigated by means of ex situ vertical scanning interferometry (VSI) measurements using flow-through and batch experiments at ambient pCO(2), pH 1-7 and room temperature in metal (Fe(II), Zn, Cu and Cd) and metal-free chloride solutions, and metal sulphate and metal-free sulphate solutions, undersaturated with respect to calcite and undersaturated or in equilibrium with respect to gypsum.Based on the VSI measurements, surface retreat was quantified at different pH and Delta G(r) < -8.1 kcal mol(-1), yielding intrinsic dissolution rate constants of calcite. These rates were used to derive an empirical rate law that takes into account the pH effect on calcite dissolution at room temperature and far from equilibrium with respect to calcite and is expressed asRate(calcite)(mol . cm(-2) . s(-1)) = 3.3 +/- 1. 8 x 10(-6) . (a(H+))(0.94+0.08) + k(2)where a(H+) is the proton activity and k(2) equals 2.5 +/- 0.8 x 10(-11) mol cm(-2) s(-1). The rhombic etch pit morphology changes at very low pH (pH < 3) due to the catalytic effect of pH on calcite dissolution, yielding rounded pseudo-rhombic etch pits.The presence of Fe(II), Cu, Zn and Cd inhibits calcite dissolution at pH 3, in contrast to the presence of sulphate, which does not affect calcite dissolution. The presence of Zn affected the etch pit morphology, yielding triangular etch pits. Under gypsum saturation conditions, gypsum (or other metal-bearing sulphate phases) precipitated on calcite as calcite dissolved, yielding a decrease in dissolution rate with time due to loss of calcite reactivity. Based on energy-dispersive X-ray fluorescence (EDXRF) measurements the precipitation rates of Zn4SO4(OH)(6) center dot 5H(2)O and Cu4SO4(OH)(6) center dot 2H(2)O were calculated to be between 1 x 10(-7) and 6 x 10(-7) mol m(-2)s(-1)., This work was financially supported by the CYCIT Project CGL2010-20984-C02-01, by Fundacio´n Ciudad de la Energı´a (Spanish Government) (project ALM11/009) and by the European Union through the ‘‘European Energy Programme for Recovery’’ and the Compostilla OXYCFB300 project and by the PANACEA project (European Community’s Seventh framework Programme FP7/2007-2013 under grant agreement number 282900). The first author is grateful to the National Science Fund of the Bulgarian Ministry of Education and Science (NZMU-1503 and DO1-904)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydromechanical characterization of CO2 injection sites

  • Vilarrasa, Víctor
  • Carrera, Jesús
  • Olivella, Sebastià
Clear understanding of coupled hydromechanical effects, such as ground deformation, induced microseismicity and fault reactivation, will be crucial to convince the public that geologic carbon storage is secure. These effects depend on hydromechanical properties, which are usually determined at metric scale. However, their value at the field scale may differ in orders of magnitude. To address this shortcoming, we propose a hydromechanical characterization test to estimate the hydromechanical properties of the aquifer and caprock at the field scale. We propose injecting water at high pressure and, possibly, low temperature while monitoring fluid pressure and rock deformation. Here, we analyze the problem and perform numerical simulations and a dimensional analysis of the hydromechanical equations to obtain curves for overpressure and vertical displacement as a function of the volumetric strain term. We find that these curves do not depend much on the Poisson ratio, except for the dimensionless vertical displacement at the top of the caprock, which does. We can then estimate the values of the Young's modulus and the Poisson ratio of the aquifer and the caprock by introducing field measurements in these plots. Hydraulic parameters can be determined from the interpretation of fluid pressure evolution in the aquifer. Reverse-water level fluctuations are observed, i.e. fluid pressure drops in the caprock as a result of the induced deformation that undergoes the aquifer-caprock system when injecting in the aquifer. We find that induced microseismicity is more likely to occur in the aquifer than in the caprock and depends little on their stiffness. Monitoring microseismicity is a useful tool to track the opening of fractures. The propagation pattern depends on the stress regime, i.e. normal, strike slip or reverse faulting. The onset of microseismicity in the caprock can be used to define the maximum sustainable injection pressure to ensure a permanent CO2 storage., This work has been funded by Fundación Ciudad de la Energía (Spanish Government) (www.ciuden.es) through the project ALM/09/018 and by the European Union through the “European Energy Programme for Recovery” and the Compostilla OXYCFB300 project. We also want to acknowledge the financial support received from the ‘MUSTANG’ (www.co2mustang.eu) and ‘PANACEA’ (www.panacea-co2.org) projects (from the European Community's Seventh Framework Programme FP7/2007-2013 under grant agreements n° 227286 and n° 282900, respectively)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dynamics of convective dissolution from a migrating current of carbon dioxide

  • Hidalgo, Juan J.
  • MacMinn, Christopher W.
  • Juanes, Rubén
During geologic storage of carbon dioxide (CO2), trapping of the buoyant CO2 after injection is essential in order to minimize the risk of leakage into shallower formations through a fracture or abandoned well. Models for the subsurface behavior of the CO2 are useful for the design, implementation, and long-term monitoring of injection sites, but traditional reservoir-simulation tools are currently unable to resolve the impact of small-scale trapping processes on fluid flow at the scale of a geologic basin. Here, we study the impact of solubility trapping from convective dissolution on the up-dip migration of a buoyant gravity current in a sloping aquifer. To do so, we conduct high-resolution numerical simulations of the gravity current that forms from a pair of miscible analogue fluids. Our simulations fully resolve the dense, sinking fingers that drive the convective dissolution process. We analyze the dynamics of the dissolution flux along the moving CO2-brine interface, including its decay as dissolved buoyant fluid accumulates beneath the buoyant current. We show that the dynamics of the dissolution flux and the macroscopic features of the migrating current can be captured with an upscaled sharp-interface model. © 2013 Elsevier Ltd., JJH acknowledges the support from the FP7 Marie Curie Actions of the European Commission, via the CO2-MATE project (PIOF-GA-2009-253678), and the FP7 EU project PANACEA (Grant Agreement No. 282900). CWM gratefully acknowledges the support of a postdoctoral fellowship from the Yale Climate & Energy Institute. RJ acknowledges funding by the US Department of Energy (DE-FE0009738)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dynamics and design of systems for geological storage of dissolved CO2

  • Pool, María
  • Carrera, Jesús
  • Vilarrasa, Víctor
  • Silva, Orlando
  • Ayora, Carlos
The standard approach for geologic storage of CO2 consists of injecting it as a supercritical CO2 phase. This approach places stringent requirements on the caprock, which must display: (1) high entry pressure to prevent the buoyancy driven upwards escape of CO2; (2) low permeability to minimize the upwards flux of brine displaced by the CO2; and (3) high strength to ensure that pressure build up does not cause caprock failure. We propose an alternative approach for cases when the above requirements are not met. The approach consists of extracting brine from the storage formation and then re-injecting it so that it mixes with CO2 at depth in the injection well. Mixing at depth reduces the pressure required for brine and CO2 at the surface. This CO2-saturated brine will sink to the aquifer bottom because it is denser than resident brine, which eliminates the risk of buoyant escape of CO2. The method is particularly favorable when the aquifer dips, because CO2-saturated brine will tend to flow downslope. We perform two- and three-dimensional numerical simulations to study how far upslope the extraction well needs to be located to ensure a very long operation without CO2 ever breaking through. Several sets of simulations were carried out to evaluate the effect of slope, temperature, pressure and CO2 concentration, which is significantly reduced if flue gas (i.e., without capture) is mixed with the brine. We analyze energy requirements to find that the system requires high permeability to be viable, but its performance is improved by taking advantage of the thermal energy of the extracted brine. © 2013 Elsevier Ltd., This work has been funded by Fundacin Ciudad de la Energa (Spanish Government) (www.ciuden.es) through the project ALM/09/018 and by the European Union through the “European Energy Programme for Recovery” and the Compostilla OXYCFB300 project. We also want to acknowledge the financial support received from the ‘TRUST’ (trust-co2.org) and ‘PANACEA’ (www.panacea-co2.org) projects (from the European Community’s Seventh Framework Programme FP7/2007-2013 under grant agreements n 309607 and n 282900, respectively)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A method for incorporating equilibrium chemical reactions into multiphase flow models for CO2 storage

  • Saaltink, Maarten W.
  • Vilarrasa, Víctor
  • De Gaspari, F.
  • Silva, Orlando
  • Carrera, Jesús
  • Rötting, Tobias
CO2 injection and storage in deep saline aquifers involves many coupled processes, including multiphase flow, heat and mass transport, rock deformation and mineral precipitation and dissolution. Coupling is especially critical in carbonate aquifers, where minerals will tend to dissolve in response to the dissolution of CO2 into the brine. The resulting neutralization will drive further dissolution of both CO2 and calcite. This suggests that large cavities may be formed and that proper simulation may require full coupling of reactive transport and multiphase flow. We show that solving the latter may suffice whenever two requirements are met: (1) all reactions can be assumed to occur in equilibrium and (2) the chemical system can be calculated as a function of the state variables of the multiphase flow model (i.e., liquid and gas pressure, and temperature). We redefine the components of multiphase flow codes (traditionally, water and CO2), so that they are conservative for all reactions of the chemical system. This requires modifying the traditional constitutive relationships of the multiphase flow codes, but yields the concentrations of all species and all reaction rates by simply performing speciation and mass balance calculations at the end of each time step. We applied this method to the H2O-CO2-Na-Cl-CaCO3 system, so as to model CO2 injection into a carbonate aquifer containing brine. Results were very similar to those obtained with traditional formulations, which implies that full coupling of reactive transport and multi-phase flow is not really needed for this kind of systems, but the resulting simplifications may make it advisable even for cases where the above requirements are not met. Regarding the behavior of carbonate rocks, we find that porosity development near the injection well is small because of the low solubility of calcite. Moreover, dissolution concentrates at the front of the advancing CO2 plume because the brine below the plume tends to reach high CO2 concentrations quite rapidly. We conclude that carbonate dissolution needs not to be feared. © 2013 Elsevier Ltd., This work was supported by the European Commission through the MUSTANG and the PANACEA projects (Seventh Framework Programme FP7/2007-2013 under Grant agreements nos. 227286 and 282900, respectively). We also want to acknowledge the financial support received from Instituto para la Diversificación y Ahorro de la Energía (IDAE, Spanish Government) and by the European Union through the “European Energy Programme for Recovery” and the Compostilla OXYCFB300 project., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dispersion variance for transport in heterogeneous porous media

  • Dentz, Marco
  • Barros, Felipe P. J. de
We study dispersion in heterogeneous porous media for solutes evolving from point-like and extended source distributions in d=2 and d=3 spatial dimensions. The impact of heterogeneity on the dispersion behavior is captured by a stochastic modeling approach that represents the spatially fluctuating flow velocity as a spatial random field. We focus here on the sample-to-sample fluctuations of the dispersion coefficients about their ensemble mean. For finite source sizes, the definition of dispersion coefficients in single realizations is not unique. We consider dispersion measures that describe the extension of the solute distribution, as well as dispersion coefficients that quantify the solute spreading relative to injection points of the partial plumes that constitute the solute distribution. While the ensemble averages of these dispersion quantities may be identical, their fluctuation behavior is found to be different. Using a perturbation approach in the fluctuations of the random flow field, we derive explicit expressions for the temporal evolution of the variances of the dispersion coefficients between realizations. Their evolution is governed by the typical dispersion time over the characteristic heterogeneity scale and the dimensions of the source distribution. We find that the dispersion variance decreases toward zero with time in d=3 spatial dimensions, while in d=2 it converges toward a finite long time value that is independent of the source dimensions. © 2013. American Geophysical Union. All Rights Reserved., F.P.J.B. acknowledges the partial support of the Spanish Juan de la Cierva program. MD acknowledges the support of the FP7 EU project PANACEA (grant agreement 282900) and the Spanish Ministry of Economy and Competitivity through the project HEART (CGL2010–18450)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A non-local two-phase flow model for immiscible displacement in highly heterogeneous porous media and its parametrization

  • Tecklenburg, Jan
  • Neuweiler, Insa
  • Dentz, Marco
  • Carrera, Jesús
  • Geiger, Sebastian
  • Abramowski, Christian
  • Silva, Orlando
In this paper, we present an upscaled model for horizontal immiscible displacement in highly heterogeneous media. This type of heterogeneity can be found, for instance, in fractured rock, which consists of two flow domains, a mobile fracture and a virtually immobile matrix. We derive an upscaled double-continuum model capable of predicting flow in mobile-immobile domains using homogenization theory. The model consists of a flow equation for the saturation of displacing fluid in the fracture domain, and a capillary flow equation for saturation in the matrix, which are coupled via a source term. By linearizing capillary counter current flow in the matrix domain, we combine this system of equations into a non-local single-equation model for the fracture saturation, which can be interpreted as a multi-rate mass-transfer (MRMT) model for immiscible displacement. We discuss this simplification and the parametrization of the upscaled model equation from local hydraulic parameters obtained from rock samples and from knowledge of the average flow properties of the fracture network. We demonstrate its performance for predicting two-phase flow by considering a single fracture with imbibition into a rectangular matrix domain. The upscaled model is parameterized directly from geometry and hydraulic parameters of matrix and fracture of the reference model, which means that no parameters need to be fitted. We compare the detailed and upscaled models in terms of breakthrough curves for the displaced fluid at a control plane within the medium. Both the detailed numerical simulations and the upscaled model show a preasymptotic t - 1 / 2 scaling and a breakoff at the characteristic time scale for filling the matrix by counter current flow. © 2013 Elsevier Ltd., M. D. and J. C. acknowledge the support of the FP7 EU project PANACEA (Grant No. 282900), and the Spanish Ministry of Economy and Competitivity through the project HEART (CGL2010-18450)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Flow intermittency, dispersion, and correlated continuous time random walks in porous media

  • De Anna, Pietro
  • Le Borgne, Tanguy
  • Dentz, Marco
  • Tartakovsky, Alexandre M.
  • Bolster, Diogo
  • Davy, Philippe
We study the intermittency of fluid velocities in porous media and its relation to anomalous dispersion. Lagrangian velocities measured at equidistant points along streamlines are shown to form a spatial Markov process. As a consequence of this remarkable property, the dispersion of fluid particles can be described by a continuous time random walk with correlated temporal increments. This new dynamical picture of intermittency provides a direct link between the microscale flow, its intermittent properties, and non-Fickian dispersion. © 2013 American Physical Society., P. de Anna and T. Le Borgne acknowledge the financial support of the European Commission through FP7 ITN project IMVUL (Grant No. 212298), and Marie Curie ERG grant ReactiveFlows (Grant No. 230947). A. Tartakovsky was supported by the ASCR Office of the U.S. Department of Energy. D. Bolster was supported by NSF Grant No. EAR-1113704. M. Dentz acknowledges the support of the FP7 EU project PANACEA (Grant No. 282900)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Laboratory-scale interaction between CO dos-rich brine and reservoir rocks (Limestone and sandstone)

  • García Rios, María
  • Liquot, Linda
  • Soler, Josep M.
  • Cama, Jordi
In the laboratory, synthetically fractured cores of limestone and sandstone were reacted with CO2-rich brines at flow rates ranging from 0.2 to 60 mL h−1 and 80 bar pCO2 and 60 °C (supercritical CO2 conditions). Interaction between the sulfate-CO2-rich brines and the primary minerals of the rock caused significant permeability variations. Calcite dissolution was clearly identified and in some case associated with gypsum (or anhydrite) precipitation., This work was financially supported by the CY CIT Project CGL2010-20984-C02-01, by Fundación Ciudad de la Energía (Spanish Government) (pro ject ALM11/009) and by th e European Union through the “European Energy Programme for Recovery” and the Compostilla OXYCFB300 project and by the PANACEA project (European Community’s Sevent h Framework Programme FP7/2007-2013 under grant agreement number 282900)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Semianalytical solution for CO2 plume shape and pressure evolution during CO2 injection in deep saline formations

  • Vilarrasa Riaño, Víctor|||0000-0003-1169-4469
  • Carrera Ramírez, Jesús|||0000-0002-8054-4352
  • Bolster, Diogo
  • Dentz, Marco|||0000-0002-3940-282X
The injection of supercritical carbon dioxide (CO2) in deep saline aquifers leads to the formation of a CO2 rich phase plume that tends to float over the resident brine. As pressure builds up, CO2 density will increase because of its high compressibility. Current analytical solutions do not account for CO2 compressibility and consider a volumetric injection rate that is uniformly distributed along the whole thickness of the aquifer, which is unrealistic. Furthermore, the slope of the CO2 pressure with respect to the logarithm of distance obtained from these solutions differs from that of numerical solutions. We develop a semianalytical solution for the CO2 plume geometry and fluid pressure evolution, accounting for CO2 compressibility and buoyancy effects in the injection well, so CO2 is not uniformly injected along the aquifer thickness. We formulate the problem in terms of a CO2 potential that facilitates solution in horizontal layers, with which we discretize the aquifer. Capillary pressure is considered at the interface between the CO2 rich phase and the aqueous phase. When a prescribed CO2 mass flow rate is injected, CO2 advances initially through the top portion of the aquifer. As CO2 is being injected, the CO2 plume advances not only laterally, but also vertically downwards. However, the CO2 plume does not necessarily occupy the whole thickness of the aquifer. We found that even in the cases in which the CO2 plume reaches the bottom of the aquifer, most of the injected CO2 enters the aquifer through the layers at the top. Both CO2 plume position and fluid pressure compare well with numerical simulations. This solution permits quick evaluations of the CO2 plume position and fluid pressure distribution when injecting supercritical CO2 in a deep saline aquifer., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A fractal model to describe the evolution of multiphase flow properties during mineral dissolution

  • Guarracino, Luis
  • Roetting, Tobias Stefan|||0000-0001-7675-3541
  • Carrera Ramírez, Jesús|||0000-0002-8054-4352
Understanding the changes in multiphase flow parameters caused by mineral dissolution-precipitation is required for multiple applications ranging from geological storage of CO2, enhanced geothermal energy production or ground water pollution. We present a physically-based theoretical model for describing the temporal evolution of porosity, saturated and relative permeabilities, retention curve and diffusion coefficient during rock dissolution by reactive fluids. The derivation of the model is based on the assumption that the pore structure of the rock can be represented by an ensemble of capillary tubes with fractal tortuosity and cumulative pore size distribution. Therefore, the model depends only on the minimum and maximum pore radii, the size of the representative elementary volume and the fractal dimensions of pore size and tortuosity, but do not need any other fitting parameters. Using this fractal description and known physical properties, we obtain analytical expressions for the hydrodynamic properties required by continuum (i.e., Darcy scale) multiphase flow models. Further, assuming periodic fluctuations in the radius of the pores, it is also possible to represent constrictivity and hysteresis. Finally, assuming a constant rate dissolution reaction it is possible to derive closed-form analytical expressions for the time evolution of porosity, retention curve, saturated and relative permeabilities and diffusion coefficient. (C) 2014 Elsevier Ltd. All rights reserved., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Semianalytical solution for CO2 plume shape and pressure evolution during CO2 injection in deep saline formations

  • Vilarrasa Riaño, Víctor
  • Carrera Ramírez, Jesús
  • Bolster, Diogo
  • Dentz, Marco
The injection of supercritical carbon dioxide (CO2) in deep saline aquifers leads to the formation of a CO2 rich phase plume that tends to float over the resident brine. As pressure builds up, CO2 density will increase because of its high compressibility. Current analytical solutions do not account for CO2 compressibility and consider a volumetric injection rate that is uniformly distributed along the whole thickness of the aquifer, which is unrealistic. Furthermore, the slope of the CO2 pressure with respect to the logarithm of distance obtained from these solutions differs from that of numerical solutions. We develop a semianalytical solution for the CO2 plume geometry and fluid pressure evolution, accounting for CO2 compressibility and buoyancy effects in the injection well, so CO2 is not uniformly injected along the aquifer thickness. We formulate the problem in terms of a CO2 potential that facilitates solution in horizontal layers, with which we discretize the aquifer. Capillary pressure is considered at the interface between the CO2 rich phase and the aqueous phase. When a prescribed CO2 mass flow rate is injected, CO2 advances initially through the top portion of the aquifer. As CO2 is being injected, the CO2 plume advances not only laterally, but also vertically downwards. However, the CO2 plume does not necessarily occupy the whole thickness of the aquifer. We found that even in the cases in which the CO2 plume reaches the bottom of the aquifer, most of the injected CO2 enters the aquifer through the layers at the top. Both CO2 plume position and fluid pressure compare well with numerical simulations. This solution permits quick evaluations of the CO2 plume position and fluid pressure distribution when injecting supercritical CO2 in a deep saline aquifer., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A fractal model to describe the evolution of multiphase flow properties during mineral dissolution

  • Guarracino, Luis
  • Roetting, Tobias Stefan
  • Carrera Ramírez, Jesús
Understanding the changes in multiphase flow parameters caused by mineral dissolution-precipitation is required for multiple applications ranging from geological storage of CO2, enhanced geothermal energy production or ground water pollution. We present a physically-based theoretical model for describing the temporal evolution of porosity, saturated and relative permeabilities, retention curve and diffusion coefficient during rock dissolution by reactive fluids. The derivation of the model is based on the assumption that the pore structure of the rock can be represented by an ensemble of capillary tubes with fractal tortuosity and cumulative pore size distribution. Therefore, the model depends only on the minimum and maximum pore radii, the size of the representative elementary volume and the fractal dimensions of pore size and tortuosity, but do not need any other fitting parameters. Using this fractal description and known physical properties, we obtain analytical expressions for the hydrodynamic properties required by continuum (i.e., Darcy scale) multiphase flow models. Further, assuming periodic fluctuations in the radius of the pores, it is also possible to represent constrictivity and hysteresis. Finally, assuming a constant rate dissolution reaction it is possible to derive closed-form analytical expressions for the time evolution of porosity, retention curve, saturated and relative permeabilities and diffusion coefficient. (C) 2014 Elsevier Ltd. All rights reserved., Peer Reviewed, Postprint (published version)