Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dynamics and design of systems for geological storage of dissolved CO2

  • Pool, María
  • Carrera, Jesús
  • Vilarrasa, Víctor
  • Silva, Orlando
  • Ayora, Carlos
The standard approach for geologic storage of CO2 consists of injecting it as a supercritical CO2 phase. This approach places stringent requirements on the caprock, which must display: (1) high entry pressure to prevent the buoyancy driven upwards escape of CO2; (2) low permeability to minimize the upwards flux of brine displaced by the CO2; and (3) high strength to ensure that pressure build up does not cause caprock failure. We propose an alternative approach for cases when the above requirements are not met. The approach consists of extracting brine from the storage formation and then re-injecting it so that it mixes with CO2 at depth in the injection well. Mixing at depth reduces the pressure required for brine and CO2 at the surface. This CO2-saturated brine will sink to the aquifer bottom because it is denser than resident brine, which eliminates the risk of buoyant escape of CO2. The method is particularly favorable when the aquifer dips, because CO2-saturated brine will tend to flow downslope. We perform two- and three-dimensional numerical simulations to study how far upslope the extraction well needs to be located to ensure a very long operation without CO2 ever breaking through. Several sets of simulations were carried out to evaluate the effect of slope, temperature, pressure and CO2 concentration, which is significantly reduced if flue gas (i.e., without capture) is mixed with the brine. We analyze energy requirements to find that the system requires high permeability to be viable, but its performance is improved by taking advantage of the thermal energy of the extracted brine. © 2013 Elsevier Ltd., This work has been funded by Fundacin Ciudad de la Energa (Spanish Government) (www.ciuden.es) through the project ALM/09/018 and by the European Union through the “European Energy Programme for Recovery” and the Compostilla OXYCFB300 project. We also want to acknowledge the financial support received from the ‘TRUST’ (trust-co2.org) and ‘PANACEA’ (www.panacea-co2.org) projects (from the European Community’s Seventh Framework Programme FP7/2007-2013 under grant agreements n 309607 and n 282900, respectively)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A methodology to detect and locate low-permeability faults to reduce the risk of inducing seismicity of fluid injection operations in deep saline formations

  • Vilarrasa, Víctor
  • Bustarret, Gil
  • Laloui, Lyesse
  • Zeidouni, Mehdi
Fluid injection in the subsurface has significantly increased over the last decades. Since fluid injection causes pressure buildup, reducing effective stresses, shear failure conditions may eventually occur, inducing microseismic and seismic events. Anticipating felt induced earthquakes that may be triggered in undetected faults is crucial for the success of fluid injection projects. We propose a methodology to detect and locate such low-permeability faults to reduce the risk of inducing felt seismic events. The methodology consists in using diagnostic plots to identify the divergence time between the logarithmic derivative of overpressure evolution measured in the field and the one that would correspond to an aquifer including the previously identified heterogeneities. We apply the proposed methodology to water and CO2 injection through a horizontal well in a confined aquifer that has faults parallel to the well. We numerically obtain type curves that allow locating low-permeability faults once the divergence time is determined from the logarithmic derivative of overpressure for both water and CO2 injection. Furthermore, we illustrate how to apply the methodology to detect multiple low-permeability faults. To perform a proper pressure management based on fault stability analysis to minimize the risk of inducing felt seismic events, the proposed methodology should be complemented with other multidisciplinary tools. This methodology can be extended to other geological settings and be used in several fluid injection applications. © 2017 Elsevier Ltd, V.V. acknowledges support from the ‘EPFL Fellows’ fellowship programme co-funded by Marie Curie, FP7 Grant agreement no. 291771. This work was funded in part by the “TRUST” project (European Community’s Seventh Framework Programme FP7/2007-2013 under grant agreement n 309607) and from “FracRisk” project (European Community’s Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement n 640979). Technical review comments of Dr. Paul Hsieh (USGS) are greatly appreciated., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of faults on stress path evolution during reservoir pressurization

  • Gheibi, Sohrab
  • Holt, Rune M.
  • Vilarrasa, Víctor
Fluid injection operations, such as CO2 storage and enhanced oil recovery (EOR), imply reservoir pressurization, which changes the effective and total stresses due to poroelastic effects. These stress changes control the geomechanical stability of discontinuities like faults and fractures. Though the effect of these pre-existing discontinuities on stress path is sometimes neglected, the stress state is altered around them. We investigate the effect of a fault on the stress path evolution when pressurizing a reservoir using an in-house hybrid FEM-DEM code called “MDEM”. Simulation results indicate that the stress path is affected by the presence of faults considered to deform elastically, especially in the vicinity of the fault in the reservoir-caprock interfaces. The stress path perturbation is caused by the shear deformation of the fault plane, which is different in the reservoir and the caprock sections. Actually, the magnitude and the extension of the stress path perturbation around a fault become larger for faults with lower shear stiffness. The upper hanging wall and the lower footwall of the fault in the reservoir-caprock interface experience a higher stress path in the horizontal and the vertical directions. Furthermore, the stress paths decrease (negative in the vertical direction) in the upper footwall and the lower hanging wall in the reservoir-caprock interfaces. The fault effect on the stress path increases as the aspect ratio of the reservoir becomes lower. Moreover, the results indicated that both the caprock and the reservoir in the footwall experience a greater change for lower Poisson's ratio of the caprock. These stress changes are independent of the in situ stress regime as long as the fault deforms elastically. However, the impact of the stress path perturbation on the stability of the reservoir and the caprock is different in a compressional (reverse faulting) and an extensional (normal faulting) stress regimes. The stress state becomes less stable in the vicinity of the fault in the reservoir and in the caprock in a compressional stress regime than in an extensional stress regime. Therefore, a compressional stress regime leads to a less stable situation due to the fault effect on the evolution of the stress path. Overall, the presence of faults alters the stress state around them, which may lead to a stress state that is closer to failure conditions than predicted by models that do not explicitly include faults. © 2017 Elsevier Ltd, This publication has been produced with partial support from the BIGCCS Centre, performed under the Norwegian research program Centres for Environment-friendly Energy Research (FME). The first two authors acknowledge the following partners for their contributions: Gassco, Shell, Statoil, TOTAL, ENGIE, and the Research Council of Norway (193816/S60). V.V. acknowledges financial support from the “TRUST” project (European Community's Seventh Framework Programme FP7/2007-2013 under grant agreement no. 309607) and from “FracRisk” project (European Community's Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement no. 640979). Authors are also grateful to SINTEF Petroleum Research provding the MDEM code., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Geomechanical analysis of the influence of CO2 injection location on fault stability

  • Vilarrasa, Víctor
  • Makhnenko, Roman Y.
  • Gheibi, Sohrab
Large amounts of carbon dioxide (CO2) should be injected in deep saline formations to mitigate climate change, implying geomechanical challenges that require further understanding. Pressure build-up induced by CO2 injection will decrease the effective stresses and may affect fault stability. Geomechanical effects of overpressure induced by CO2 injection either in the hanging wall or in the foot wall on fault stability are investigated. CO2 injection in the presence of a low-permeable fault induces pressurization of the storage formation between the injection well and the fault. The low permeability of the fault hinders fluid flow across it and leads to smaller overpressure on the other side of the fault. This variability in the fluid pressure distribution gives rise to differential total stress changes around the fault that reduce its stability. Despite a significant pressure build-up induced by the fault, caprock stability around the injection well is not compromised and thus, CO2 leakage across the caprock is unlikely to happen. The decrease in fault stability is similar regardless of the side of the fault where CO2 is injected. Simulation results show that fault core permeability has a significant effect on fault stability, becoming less affected for high-permeable faults. An appropriate pressure management will allow storing large quantities of CO2 without inducing fault reactivation. © 2016 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, The first author acknowledges the support from the “EPFL Fellows” fellowship program co-funded by Marie Curie, FP7 (Grant No. 291771) and partial support from the “TRUST” project of the European Community's Seventh Framework Programme FP7/2007–2013 (Grant No. 309607) and the “FracRisk” project of the European Community's Horizon 2020 Framework Programme H2020-EU.3.3.2.3 (Grant No. 640979). Activities of the second author are sponsored by SCCER-SoE (Switzerland) (Grant No. KTI.2013.288) and Swiss Federal Office of Energy (SFOE) project CAPROCK (Grant No. 810008154). This publication has also been produced with partial support from the BIGCCS Centre (for the third author), performed under the Norwegian research program Centers for Environment-friendly Energy Research (FME). The third author acknowledges the following partners for their contributions: Gassco, Shell, Statoil, TOTAL, ENGIE, and the Research Council of Norway (193816/S60)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Geologic Carbon Storage for Shale Gas Recovery

  • Molina, Oscar M.
  • Vilarrasa, Víctor
  • Zeidouni, Mehdi
We consider the feasibility of a novel Carbon Capture, Utilization and Storage (CCUS) concept that consists in producing oil and gas from hydrocarbon-rich shales overlying deep saline aquifers that are candidates for CO2 storage. Such geological overlapping between candidate aquifers for CO2 storage and shale plays exists in several sedimentary basins across the continental US. Since CO2 reaches the storage formation at a lower temperature than the in-situ temperature, a thermal stress reduction occurs, which may lead to hydraulic fracturing of the caprock overlying the aquifer. In this work, we use a thermo-hydro-mechanical approach for modelling a caprock-aquifer-baserock system. We show that hydraulic fracturing conditions are induced within the aquifer by thermal stress reduction caused by cooling and that hydraulic fractures eventually propagate into the lower portion of the shale play. Nonetheless, fracture height of penetration in the caprock is considerably short after 10 years of injection, so the overall caprock sealing capacity is maintained. To maximize the benefit of the proposed CCUS method, CO2 injection should be maintained as long as possible to promote the penetration depth of cooling-induced hydraulic fractures into organic-rich shales. Though drilling a horizontal well in the lower portion of the shale to produce hydrocarbons from the induced hydraulic fractures may not be technically feasible, hydrocarbons can still be produced through the injection well. The production of hydrocarbons at the end of the CO2 storage project will partly compensate the costs of CCS operations. © 2017 The Authors., This study was partially supported by the Louisiana Board of Regents — Research Competitiveness Subprogram (RCS) under contract #43950. V.V. acknowledges financial support from the “TRUST" project (European Community's Seventh Framework Programme FP7/2007-2013 under grant agreement n 309607) and from “FracRisk" project (European Community's Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement n 640979)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Long-term thermal effects on injectivity evolution during CO2 storage

  • Vilarrasa, Víctor
  • Rinaldi, Antonio Pio
  • Rutqvist, Jonny
Carbon dioxide (CO2) is likely to reach the bottom of injection wells at a colder temperature than that of the storage formation, causing cooling of the rock. This cooling, together with overpressure, tends to open up fractures, which may enhance injectivity. We investigate cooling effects on injectivity enhancement by modeling the In Salah CO2 storage site and a theoretical, long-term injection case. We use stress-dependent permeability functions that predict an increase in permeability as the effective stress acting normal to fractures decreases. Normal effective stress can decrease either due to overpressure or cooling. We calibrate our In Salah model, which includes a fracture zone perpendicular to the well, obtaining a good fitting with the injection pressure measured at KB-502 and the rapid CO2 breakthrough that occurred at the observation well KB-5 located 2 km away from the injection well. CO2 preferentially advances through the fracture zone, which becomes two orders of magnitude more permeable than the rest of the reservoir. Nevertheless, the effect of cooling on the long-term injectivity enhancement is limited in pressure dominated storage sites, like at In Salah, because most of the permeability enhancement is due to overpressure. However, thermal effects enhance injectivity in cooling dominated storage sites, which may decrease the injection pressure by 20%, saving a significant amount of compression energy all over the duration of storage projects. Overall, our simulation results show that cooling has the potential to enhance injectivity in fractured reservoirs. © 2017 Elsevier Ltd, This work was supported by the Assistant Secretary for Fossil Energy, Office of Natural Gas and Petroleum Technology, through the National Energy Technology Laboratory, under the U.S. Department of Energy Contract No. DE-AC02-05CH11231. V. Vilarrasa acknowledges financial support from the “TRUST" project (European Community's Seventh Framework Programme FP7/2007-2013 under grant agreement n. 309607) and from “FracRisk" project (European Community's Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement n. 640979). A.P. Rinaldi is currently funded by Swiss National Science Foundation (SNSF) Ambizione Energy grant (PZENP2_160555). The authors would like to thank the In Salah JIP and their partners BP, Statoil, and Sonatrach for providing field data and technical input over the past 10 years as well as for financial support during LBNL's participation in the In Salah JIP, 2011–2013, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Caprock Integrity and Induced Seismicity from Laboratory and Numerical Experiments

  • Vilarrasa, Víctor
  • Makhnenko, Roman Y.
CO2 leakage is a major concern for geologic carbon storage. To assess the caprock sealing capacity and the strength of faults, we test in the laboratory the rock types involved in CO2 storage at representative in-situ conditions. We use the measured parameters as input data to a numerical model that simulates CO2 injection in a deep saline aquifer bounded by a low-permeable fault. We find that the caprock sealing capacity is maintained and that, even if a fault undergoes a series of microseismic events or aseismic slip, leakage is unlikely to occur through ductile clay-rich faults. © 2017 The Authors. Published by Elsevier Ltd., V.V. acknowledges financial support from the “TRUST" project (European Community's Seventh Framework Programme FP7/2007-2013 under grant agreement n. 309607) and from “FracRisk" project (European Community's Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement n. 640979). R.M. acknowledges partial support from the Center for Geologic Storage of CO2, an EFRC funded by the U.S. DOE, Office of Science, BES, under Award DE-SC0C12504., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal effects on geologic carbon storage

  • Vilarrasa, Víctor
  • Rutqvist, Jonny
One of the most promising ways to significantly reduce greenhouse gases emissions, while carbon-free energy sources are developed, is Carbon Capture and Storage (CCS). Non-isothermal effects play a major role in all stages of CCS. In this paper, we review the literature on thermal effects related to CCS, which is receiving an increasing interest as a result of the awareness that the comprehension of non-isothermal processes is crucial for a successful deployment of CCS projects. We start by reviewing CO2 transport, which connects the regions where CO2 is captured with suitable geostorage sites. The optimal conditions for CO2 transport, both onshore (through pipelines) and offshore (through pipelines or ships), are such that CO2 stays in liquid state. To minimize costs, CO2 should ideally be injected at the wellhead in similar pressure and temperature conditions as it is delivered by transport. To optimize the injection conditions, coupled wellbore and reservoir simulators that solve the strongly non-linear problem of CO2 pressure, temperature and density within the wellbore and non-isothermal two-phase flow within the storage formation have been developed. CO2 in its way down the injection well heats up due to compression and friction at a lower rate than the geothermal gradient, and thus, reaches the storage formation at a lower temperature than that of the rock. Inside the storage formation, CO2 injection induces temperature changes due to the advection of the cool injected CO2, the Joule-Thomson cooling effect, endothermic water vaporization and exothermic CO2 dissolution. These thermal effects lead to thermo-hydro-mechanical-chemical coupled processes with non-trivial interpretations. These coupled processes also play a relevant role in “Utilization” options that may provide an added value to the injected CO2, such as Enhanced Oil Recovery (EOR), Enhanced Coal Bed Methane (ECBM) and geothermal energy extraction combined with CO2 storage. If the injected CO2 leaks through faults, the caprock or wellbores, strong cooling will occur due to the expansion of CO2 as pressure decreases with depth. Finally, we conclude by identifying research gaps and challenges of thermal effects related to CCS. © 2016 Elsevier B.V., V.V. acknowledges financial support from the “TRUST” project (European Commission Seventh Framework Programme FP7/2007–2013 under grant agreement n 309607) and from “FracRisk” project (European Community's Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement n 640979). This work was funded in part by the Assistant Secretary for Fossil Energy, National Energy Technology Laboratory, National Risk Assessment Partnership, of the U.S. Department of Energy under Contract No. DEAC02-05CH11231. The authors would like to thank Patricia Lopez for drawing Fig. 1., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Numerical analysis of mixed-mode rupture propagation of faults in reservoir-caprock system in CO2 storage

  • Gheibi, Sohrab
  • Vilarrasa, Víctor
  • Holt, Rune M.
Injection-induced seismicity and caprock integrity are among the most important concerns in CO2 storage operations. Understanding and minimizing fault/fracture reactivation in the first place, and rupture growth/propagation beyond its surface afterwards, are fundamental to achieve a successful deployment of geologic carbon storage projects. Rock fracture mechanics provides useful concepts to study the propagation of discontinuities such as pre-existing faults and fractures. In this paper, we aim at developing a methodology to investigate the rupture propagation likelihood of faults/fractures inside a reservoir and its surrounding (including the caprock) as a result of reservoir pressurization. In this methodology, mode I (tensile) and mode II (shear) stress intensity factors of a given fault/fracture are calculated based on Linear Elastic Fracture Mechanics. A fault/fracture can propagate either in mode I, mode II or a combination of both (also called mixed-mode) based on the comparison of the stress intensity factors and fracture toughness. The proposed methodology, which has been embedded into a hybrid Finite Element Method-Discrete Element Method in-house code called MDEM, has the capability to obtain the direction of mode I and mode II rupture in front of a fault/fracture tip. Two coefficients are defined as stress intensity paths (κ) for a fault/fracture, as the change of stress intensity factors for the two failure modes of a given discontinuity per unit pore pressure change of the reservoir after injection. Based on these stress intensity path coefficients, a relationship is given to calculate the threshold pressure buildup above which the two propagation modes may occur. We use the proposed methodology to investigate the rupture growth likelihood of faults in and around a closed reservoir due to its pressurization. Simulation results indicate that mode I failure is likely to occur inside the reservoir for faults with low dip angle in compressional stress regimes. However, the initiated mode I failure may not have the chance to grow upwards because the minimum principal is in the vertical direction and thus, the initiated rupture tends to rotate and grow horizontally. In contrast, mode I rupture is likely to occur in the caprock for faults with high dip angle in extensional stress regimes. The initiated rupture may grow upwards if the newly created fracture becomes hydraulically connected with the reservoir. We find that mode II rupture is not likely to occur in any of the investigated scenarios. Simulation results show that the coefficients of the stress intensity factors depend on the faults location, dipping angle, fault length, presence of other faults, reservoir aspect ratio and reservoir and caprock stiffness., This publication has been produced with partial support from the BIGCCS Centre, performed under the Norwegian research program Centres for Environment-friendly Energy Research (FME). The first two authors acknowledge the following partners for their contributions: Gassco, Shell, Statoil, TOTAL, ENGIE, and the Research Council of Norway (193816/S60). V.V. acknowledges financial support from the “TRUST” project (European Community's Seventh Framework Programme FP7/2007-2013 under grant agreement no. 309607) and from “FracRisk” project (European Community's Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement no. 636811). Authors are also grateful to SINTEF Petroleum Research providing the MDEM code., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Field and laboratory studies of geomechanical response to the injection of CO2.

  • Vilarrasa, Víctor
  • Makhnenko, Roman Y.
  • Rutqvist, J.
V. Vilarrasa acknowledges financial support from the “TRUST" project (European Community’s Seventh Framework Programme FP7/ 2007 2013 under grant agreement no. 309607) and from “FracRisk" project (European Community’s Horizon 2020 Framework Programme H2020-EU.3.3.2.3 under grant agreement no. 636811). R. Makhnenko acknowledges support from the Center for Geologic Storage of CO2, an EFRC funded by the U.S. DOE, Office of Science, BES, under Award DE-SC0C12504. J. Rutqvist acknowledges funding by the Assistant Secretary for Fossil Energy, National Energy Technology Laboratory, National Risk Assessment Partnership of the U.S. Department of Energy under Contract No. DEAC02-05CH11231.