Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical simulations for evaluating the impact of advanced insulation coatings on H2 additivated gasoline lean combustion in a turbocharged

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Margot , Xandra|||0000-0002-2639-0444
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] This paper presents a numerical methodology based on Computational Fluid Dynamics (CFD) simulations to understand the physics of heat losses through the cylinder walls coated with different materials, taking into account other important factors such as surface roughness and near wall flow velocity in a turbocharged spark-ignited (SI) engine. Engine closed cycle simulations have been performed to estimate the thermodynamic evolution of the charge inside the cylinder and therefore, to evaluate the effect of roughness on heat transfer and combustion at real operating conditions. The model has been validated by using experimental data for two different steady-state operation conditions of a fully instrumented engine. In general, the maximum rate of heat release is reduced as the roughness is increased. Observed trends indicate that the heat transfer variation is mainly caused by changes in the combustion process due to the surface roughness, rather than to the effects of the coating material properties/characteristics (the increase of the effective contact area, porosity, etc.). Lastly, the comparison between uncoated and coated engine have shown that maximal gains around 5% in heat loss could be achieved, with very limited efficiency improvement, whereas the knock tendency increases., J. Gomez-Soriano is partially supported through the Programa de Apoyo para la Investigation y Desarrollo (PAID) of Universitat Politecnica de Valencia [Grant No. FPI-S2-2016-1353].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

New approach to study the heat transfer in internal combustion engines by 3D modelling

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Margot , Xandra|||0000-0002-2639-0444
  • Escalona-Cornejo, Johan Enrique
[EN] The stringent environmental constraints have led the industry to look for new technologies that improve the design of internal combustion engines (ICE), mainly focused on achieving higher thermal efficiency and reducing pollutant emissions. Numerical simulations play a key role for optimizing engine design, but modelling the physical processes such as the combustion and the heat transfer to the walls, represents a challenge due to the complexity of the phenomena involved. Combustion has to be modeled properly, and heat transfer models from gas to wall require coupling with solid wall models (CHT Conjugate Heat Transfer calculations). In this paper, a new approach is presented, focused on optimizing the computing time needed to perform CHT simulations. It is based on the use of the Rate of Heat Release (RoHR) obtained from a CFD calculation to replace the combustion process. The study is performed for a spark ignition (SI) engine. The proposed approach is validated for the heat transfer to the piston wall. The study shows that the CHT-RoHR approach yields very good results in terms of spatially averaged values during the whole engine cycle and allows considerable reduction in computational cost. It is therefore very useful to perform parametric studies., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 724084.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A one-dimensional modeling study on the effect of advanced insulation coatings on internal combustión engine efficiency

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Margot , Xandra|||0000-0002-2639-0444
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] This article presents a study of the impact on engine efficiency of the heat loss reduction due to in-cylinder coating insulation. A numerical methodology based on one-dimensional heat transfer model is developed. Since there is no analytic solution for engines, the one-dimensional model was validated with the results of a simple "equivalent" problem, and then applied to different engine boundary conditions. Later on, the analysis of the effect of different coating properties on the heat transfer using the simplified one-dimensional heat transfer model is performed. After that, the model is coupled with a complete virtual engine that includes both thermodynamic and thermal modeling. Next, the thermal flows across the cylinder parts coated with the insulation material (piston and cylinder head) are predicted and the effect of the coating on engine indicated efficiency is analyzed in detail. The results show the gain limits, in terms of engine efficiency, that may be obtained with advanced coating solutions., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The equipment used in this work has been partially supported by FEDER project funds "otacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT)'' (Grant No. FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Spanish Government. This project has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No. 724084.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Conjugate heat transfer study of the impact of &quot, thermo-swing&quot, coatings on internal combustion engines heat losses

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Margot , Xandra|||0000-0002-2639-0444
  • Escalona-Cornejo, Johan Enrique
[EN] To comply with the very strict emissions regulation the automotive industry is succeeding in developing ever more efficient engines, and there is scope for more improvements. In this regard, some investigations have suggested that insulating the combustion chamber walls of an internal combustion engine (ICE) yield low thermal losses. Most of the literature available on this topic presents simplified models that do not allow studying in detail the coating impact on engine efficiency. A more precise approach that consists in the combination of Computational Fluid Dynamics (CFD) and Conjugate Heat Transfer (CHT) simulations is used in this paper to predict the heat losses through the combustion chamber walls of a spark ignition (SI) engine. Two configurations are considered for the single cylinder engine: the metallic case and the same engine with coated piston and cylinder head. The insulation material has a low thermal conductivity (k < 1.0W/(mK)). The numerical results are validated by comparison with the results of a 1D heat transfer model and with experimental data for a medium load operation point (3000 rpm -7 bar IMEP). The solutions obtained are analysed in detail in terms of wall temperature distribution and heat transfer. The impact of the coating on the engine efficiency is thus assessed. The CFD-CHT calculations yields very good results in terms of heat transfer prediction during the whole engine cycle., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 724084.