Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 58
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of the improvement of internal combustion engines cooling system using nanofluids and nanoencapsulated phase change materials

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Dreif-Bennany, Amin
[EN] In recent years, due to the increasing need to reduce consumption of reciprocating internal combustion engines, new researches on different subsystems have raised. Among them, the use of nanofluids as a coolant medium seems to be an interesting alternative. In this work, the potential benefits of using nanofluids in the cooling system using an engine lumped model are studied. The methodology of the study starts with a whole description and validation of the model in both steady and transient conditions by means of a comparison with experimental results. Then, the potential benefits that could be obtained with the use of nanofluids are studied in a theoretical way. After that, the model is used to estimate the behavior of the system using different nanofluids in both stationary and transient conditions. The main results show that the advantages of using these new refrigerants are limited., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT)'' (grant number FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Spanish Government.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Velocity field analysis of the high density, high pressure diesel spray

  • Payri, Raul|||0000-0001-7428-5510
  • Viera-Sotillo, Juan Pablo
  • Wang, Huan
  • Malbec, Louis-Marie
In this study, particle image velocimetry (PIV) measurements have been performed extensively on a non-reactive dense diesel spray injected from a single orifice injector, under various injection pressure and steady ambient conditions, in a constant flow chamber. Details of PIV setup for diesel spray measurement without additional seeding are explained first. The measured velocity profiles are compared to those obtained from other similar measurements performed in a different institution, as well as those obtained from a 1D spray model simulation, presenting in both cases a good level of agreement. In addition, the velocity fields under various injection pressures and ambient densities show the dominant effects of these parameters on the behavior of diesel spray. The self-similarity of the transverse cut profiles of axial velocity is evaluated, showing that the measurements are in agreement with the hypothesis of self-similar velocity profiles. Finally, the effect of injection pressure and ambient density on the velocity fluctuations is presented and analyzed as well. While the experimental results presented here could help to understand the complex diesel fuel-air mixing process during injection, they also provide additional spray velocity data for future computational model validation, following the main idea of the Engine Combustion Network., This work was sponsored by "Ministerio de Economia y Competitividad" of the Spanish Government in the frame of the Project "Comprension de la influencia de combustibles no convencionales en el proceso de injeccion y combustion tipo diesel", Reference TRA2012-36932. Additionally, the optical equipment used for the project was purchased with funding from Ministerio de Economia y Competitividad FEDER-ICTS-2012-06.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational fluid dynamics assessment of subcooled flow boiling in internal-combustion engine-like conditions at low flow velocities with a volume-of-fluid model and a two-fluid model

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Olmeda, P.|||0000-0002-3161-0165
  • Gil, A.|||0000-0001-7192-6992
  • Cornejo, Omar
The use of subcooled flow boiling is a convenient option for the thermal management of downsized engines, but proper control of the phenomenon requires the accurate prediction of heat transfer at the coolant side, for which the use of computational fluid dynamics is a suitable alternative. While in most of the applications found to engine cooling a single-fluid equivalent method is used, in this paper the performance of a twofluid method is evaluated in engine-like conditions with special interest in the low velocity range. The results indicate that the description of the process at low velocities provided by the two-fluid method is better than that of a single-fluid model, while model calibration is simpler and more robust and the computational cost is substantially reduced., The equipment used in this work was partially supported by FEDER project funds 'Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte' (grant number FEDER-ICTS-2012-06), framed in the operational program of the unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. This work was partially supported by Senacyt Panama (Omar Cornejo, grant 797-7-2)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of the injector design on the combustion noise of gasoline partially premixed combustion in a 2-stroke engine

  • Broatch, A.|||0000-0001-9991-1039
  • Margot , Xandra|||0000-0002-2639-0444
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] In this paper, a numerical Computational Fluid Dynamics (CFD) study is carried out with the purpose of understanding how the injector design may impact on the in-cylinder processes, which cause noise emission. This study is based on a combination of the gasoline partially premixed combustion concept with a new high speed direct injection 2-stroke engine, which emerges as a promising solution able to comply with nitrous oxides and particulate matter emissions standards, while ensuring combustion control and stability. The original engine configuration is varied by modifying the included spray angle and the number of injector nozzles in order to evaluate other design solutions for mitigating combustion noise. Results show that the maximum pressure time-derivative achieved during the combustion is the most influential parameter on the acoustic response of the in-cylinder noise source. However, they also evidence that for some operation conditions the resonance phenomena can enhance their contribution, thus playing a relevant role in the engine noise level. Further analysis allowed to identify three combustion related parameters, which characterise this phenomenon and allow identifying key paths to minimize its levels. (C) 2017 Elsevier Ltd. All rights reserved., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" from the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. J. Gomez-Soriano is partially supported by an FPI contract (FPI-S2-2016-1353) of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-16)" of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Redesign and characterization of a single-cylinder optical research engine to allow full optical access and fast cleaning during combustion studies

  • Benajes, Jesús|||0000-0002-1653-9188
  • Pastor, José V.|||0000-0003-4113-4681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
[EN] This work describes the update of an optical engine design with the aim of increasing its capabilities when used for combustion studies. The criteria followed to perform the optical engine redesign were: maximize the optical accessibility to the combustion chamber, minimize the time consumed to clean the optical parts, and minimize the adaptation costs. To meet these requirements, a modular design using window-holders to fit the windows in the optical flange, was proposed. This novel solution allows optical access near the cylinder-head plane while maintaining high operating flexibility (i.e. fast transition between optical and metal engine, and very fast cleaning procedure). The new engine design has three additional optical accesses to the combustion chamber and resulted in more efficient operation compared to the original design, reducing the time consumed to clean the optical parts from 40 down to 10 min. Two main parameters of the new engine were characterized, the effective compression ratio and the rotatory flow field velocity (swirl). The characterization process revealed very similar values between the effective and geometric compression ratios (14.7:1 vs 14.2:1), which confirms the use of appropriate dimensional tolerances during the machining process and low amount of blow-by. Finally, the swirl ratio was characterized through particle image velocimetry measurements for different crank timings at 1200 rpm and motored conditions, using the optical piston with a cylindrical bowl. This method revealed swirl ratios varying from 1 to 1.7 depending on the timing considered, with increasing trend as the piston moves towards the top dead center., This work has been partially funded by the Spanish Government under the project HiReCo TRA2014-58870-R. The equipment used has been partially funded by FEDER project ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. The author J. Monsalve-Serrano acknowledges the financial support from the Universitat Politecnica de Valencia under the grant "Ayudas Para la Contratacion de Doctores para el Acceso al Sistema Espanol de Ciencia, Tecnologia e Innovacion". The authors wish to thank Daniel Lerida for his technical work during the redesign process.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the influence of pre-DPF water injection technique on pollutants emission

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Campos, Daniel
The pressure drop across DPFs directly affects the exhaust back-pressure and fuel economy of compression ignition engines. Pressure drop is related to the soot trapped inside the DPF, increasing exhaust back-pressure as the soot mass loading does. Consequently, regeneration strategies are required to remove the soot collected in the DPF. However, these processes usually involve additional fuel consumption. Considering this context, control techniques to reduce the exhaust back-pressure dependence on DPF soot loading are arising. One technique is based on the pre-DPF water injection events to get an optimum redistribution of the soot layer leading to a reduction of DPF pressure drop. This paper is focused to establish a comprehensive analysis of the change in pollutants emitted due to this technique application. The effects of this technique on filtration efficiency and particle size distribution are also analysed during and after a DPF loading test. Results have shown a dilution effect on gaseous compounds and a negligible particle emission during the pre-DPF water injection event (<2 mg), increasing PSD mode downstream the DPF to the mode of the raw emission. Nevertheless, there are not relevant effects on overall filtration efficiency, which keeps value comparable to baseline operation clearly higher than 99%., This work has been partially supported by Government of Spain through grant number FEDER-ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation, and through grant number TRA2013-40853-R of the Ministry of Economy and Competitiveness.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Simulations and measurements of automotive turbocharger compressor whoosh noise

  • Broatch, A.|||0000-0001-9991-1039
  • Galindo, José|||0000-0001-6068-182X
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Daglish, Andrew
  • Sharma, Raj K.
Turbocharger noise has become a major concern in downsized automotive engine development. In this paper, the analysis is focused on the whoosh noise produced by the compressor when it is working near surge. A centrifugal compressor has been acoustically characterized on a turbocharger test rig mounted on an anechoic chamber. Three in-duct pressure signals forming a linear array are registered in order to obtain pressure components. In this way, meaningful pressure spectra and sound intensity level (SIL) compressor maps are obtained, showing an increase of SIL in the frequency window corresponding to whoosh noise. Besides, detached eddy simulations (DES) of the centrifugal compressor flow in two operating conditions near surge are performed. Good agreement is found between the experimental measurements and the CFD solutions in terms of predicted pressure spectra. Flow analysis is used to identify patterns responsible for the different features of the pressure spectra. At the simulated conditions, rotating instabilities in the compressor diffuser and inducer cause pressure oscillations in the frequency range of whoosh noise., The equipment used in this work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant no. TRA2012-36954 and by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Measuring turbocharger compressor inlet backflow through particle image velocimetry

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Pastor, José V.|||0000-0003-4113-4681
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Sharma, Raj K.
  • Cheung, R.
[EN] An experimental measurement campaign is presented where particle image velocimetry (PIV) was used in an effort to characterize the velocity field in a turbocharger compressor when unstable operating conditions lead to flow reversing from the diffuser into the inlet pipe. Previous studies have successfully used this and similar techniques, but the most relevant results have been obtained in an open compressor where the backflow can diffuse into the ambient. In this work a glass pipe long enough to confine the full extent of the backflow has been used. Advantage was taken from the fact that this backflow is at higher temperature due to the compression process, enabling a preliminary work where a thermocouple array was used to estimate its maximum length across the compressor map. Using these results as a reference both axial and transversal velocity fields were measured. Issues associated with each one are described, along with relevant results that show how the technique correctly identifies the reversed flow, a conclusion that is supported by the comparison of the velocity average and standard deviation profiles with those of measured temperature., This work has been partially supported by Jaguar Land Rover Limited, Abbey Road, Whitley, Coventry CV3 4LF, UK. The equipment used in this work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant no DPI2015-70464-R and by FEDER - EU project funds "Dotaciem de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. J. Garcia-Tiscar was partially supported through contract FPI-S22015-1530 of the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Internal flow characterization on an ECN GDi injector

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Vaquerizo, Daniel
In the past years the awareness on climate change, air pollution and fossil fuel availability has been growing, this has pushed the automotive industry to search for new combustion systems as well as for the optimization of the current ones. In this respect, the gasoline engine has much potential for improvement especially in regard to fuel consumption. GDi engines are the natural upgrade of PFI gasoline engines and their share is expected to grow over the years. This paper explores the use of rate of injection (ROI) and rate of momentum (ROM) to characterize the internal flow of an ECN gasoline injector. Rate of momentum has been successfully used in Diesel injectors with this objective and for the first time, the measurements have been made on a GDi injector. The paper focuses on the experimental set-up used and the different uncertainties and difficulties to translate the typically mea-sured Diesel techniques to a gasoline injector and it presents the measurements obtained for rate of injection and for the different methodologies used for rate of momentum. The paper also contains internal flow simulations performed with CONVERGE to compare the results with those gathered experimentally, the comparison between the computational simulations and the experimental data resulted in good agreement., This research was performed in the frame of project "Estudio de la interaccion chorropared en condiciones realistas de motor" reference TRA2015-67679-c2-1-R from Ministerio de Economia y Competitividad (Spanish Ministry of Economy). The equipment used in this work has been partially supported by FEDER Project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)," framed in the operation program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental methodology for turbocompressor in-duct noise evaluation based on beamforming wave decomposition

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Margot , Xandra|||0000-0002-2639-0444
  • García-Tíscar, Jorge|||0000-0003-4934-4587
An experimental methodology is proposed to assess the noise emission of centrifugal turbocompressors like those of automotive turbochargers. A step-by-step procedure is detailed, starting from the theoretical considerations of sound measurement in flow ducts and examining specific experimental setup guidelines and signal processing routines. Special care is taken regarding some limiting factors that adversely affect the measuring of sound intensity in ducts, namely calibration, sensor placement and frequency ranges and restrictions. In order to provide illustrative examples of the proposed techniques and results, the methodology has been applied to the acoustic evaluation of a small automotive turbocharger in a flow bench. Samples of raw pressure spectra, decomposed pressure waves, calibration results, accurate surge characterization and final compressor noise maps and estimated spectrograms are provided. The analysis of selected frequency bands successfully shows how different, known noise phenomena of particular interest such as mid-frequency "whoosh noise" and low-frequency surge onset are correlated with operating conditions of the turbocharger. Comparison against external inlet orifice intensity measurements shows good correlation and improvement with respect to alternative wave decomposition techniques., The equipment used in this work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant no. TRA2012-36954 and by FEDER project funds "Dotacion de infraestructuras cientifico-tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. J. Garcia-Tiscar is partially supported through contract FPI-S2-2015-1530 of the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of laser induced plasma ignition timing and location on Diesel spray combustion

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Pinotti, Mattia
[EN] An experimental study about the influence of the local conditions at the ignition location on combustion development of a direct injection spray is carried out in an optical engine. A laser induced plasma ignition system has been used to force the spray ignition, allowing comparison of combustion's evolution and stability with the case of conventional autoignition on the Diesel fuel in terms of ignition delay, rate of heat release, spray penetration and soot location evolution. The local equivalence ratio variation along the spray axis during the injection process was determined with a 1D spray model, previously calibrated and validated. Upper equivalence ratios limits for the ignition event of a direct injected Diesel spray, both in terms of ignition success possibilities and stability of the phenomena, could been determined thanks to application of the laser plasma ignition system. In all laser plasma induced ignition cases, heat release was found to be higher than for the autoignition reference cases, and it was found to be linked to a decrease of ignition delay, with the premixed peak in the rate of heat release curve progressively disappearing as the ignition delay time gets shorter. Ignition delay has been analyzed as a function of the laser position, too. It was found that ignition delay increases for plasma positions closer to the nozzle, indicating that the amount of energy introduced by the laser induced plasma is not the only parameter affecting combustion initiation, but local equivalence ratio plays a major role, too. (C) 2016 Elsevier Ltd. All rights reserved., The authors acknowledge that this research work has been partly funded by the Government of Spain under the project HiR-eCo TRA2014-58870-R and grant BES-2015-072119. The equipment used in this work has been partially supported by FEDER project ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the influence of inlet elbow radius on recirculating backflow, whoosh noise and efficiency in turbocharger compressors

  • Broatch, A.|||0000-0001-9991-1039
  • Ruiz-Rosales, Santiago|||0000-0001-9536-3696
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Roig-Villanueva, Ferran
[EN] While the influence of inlet geometry on turbocharger compressor behaviour has usually been investigated in terms of performance, surge margin and efficiency, data is scarce regarding the impact of the inlet flow field onto the noise emission. In many applications where tight packaging is required, a 90° elbow is placed just upstream of the compressor inducer. This can create a distortion of the incoming flow that affects the turbocharger operation; a distortion that is related to the radius of the elbow. In this experimental investigation three 90° elbow inlets are tested, measuring the in-duct sound intensity through acoustic beamforming, the spectral signature of the noise, and the distortion of the high temperature backflow typical of partially stalled conditions by means of thermocouple arrays. Results show that a tighter elbow radius not only impacts efficiency but also increases inlet noise at conditions close to surge. Spectral analysis shows that this increase is mainly produced in the form of a medium frequency broadband noise usually known as `whoosh¿ in the literature. On the other hand, effect on the outlet is less noticeable. Measurements of the recirculated backflow distortion in terms of circumferential skewness show good correlation with whoosh noise increase, indicating that flow distortion caused by tighter elbows at marginal surge conditions facilitates the transmission of whoosh noise oscillations to the inlet duct, worsening the acoustic behaviour of the system., The equipment used in this work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant DPI2015-70464-R and by FEDER project funds 'Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)' framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. F. Roig is partially supported through the Programa de Apoyo para la Investigacion y Desarrollo of Universitat Politecnica de Valencia (PAID-01-17).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of pollutants emission and aftertreatment efficiency in a GTDi engine including cooled LP-EGR system under different steady-state operating conditions

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Luján, José M.|||0000-0001-6133-8943
  • Climent, H.|||0000-0002-2407-5651
  • Campos, Daniel
Nowadays, EGR systems are being incorporated in the research focused on spark-ignition direct-injection engines as a solution to the problems presented by them; i.e. knock risk and high combustion temperature which produces high NOx emission. Since the major part of the investigations are centered on engine performance or engine simulation aside pollutants emission and aftertreatment evaluation, this paper focuses on these topics: gaseous and particle emission analysis and aftertreatment efficiency evaluation when cooled LP-EGR system is applied to a GTDi engine. This work has been performed in a 4-cylinder, turbocharged, direct-injection gasoline engine with 2.0 L displacement. The equipment used in this study are TSI-EEPS for particle measurement and HORIBA MEXA 1230-PM for soot measurement being HORIBA MEXA 7100-DEGR with a heated line selector the system employed for regulated gaseous emission measurement and aftertreatment evaluation. A reduction around 50% of NOx with an increase of HC and CO emissions was found in medium-load operating points. At full-load conditions, the suppression of fuel enrichment including EGR leads in a drastically reduction in CO maintaining similar HC and NOx emissions. Furthermore, PN and soot emissions also decrease as EGR is included and spark timing advanced in all the tested conditions., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER- ICTS-2012-06)", framed in the operational program of singular scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Understanding the unsteady pressure field inside combustion chambers of compression-ignited engines using a computational fluid dynamics approach

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Margot , Xandra|||0000-0002-2639-0444
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] In this article, a numerical methodology for assessing combustion noise in compression ignition engines is described with the specific purpose of analysing the unsteady pressure field inside the combustion chamber. The numerical results show consistent agreement with experimental measurements in both the time and frequency domains. Nonetheless, an exhaustive analysis of the calculation convergence is needed to guarantee an independent solution. These results contribute to the understanding of in-cylinder unsteady processes, especially of those related to combustion chamber resonances, and their effects on the radiated noise levels. The method was applied to different combustion system configurations by modifying the spray angle of the injector, evidencing that controlling the ignition location through this design parameter, it is possible to decrease the combustion noise by minimizing the resonance contribution. Important efficiency losses were, however, observed due to the injector/bowl matching worsening which compromises the performance and emissions levels., The authors want to express their gratitude to CONVERGENT SCIENCE Inc. and Convergent Science GmbH for their kind support for performing the CFD calculations using CONVERGE software.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental verification of hydrodynamic similarity in hot flows

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Roig-Villanueva, Ferran
[EN] This paper examines a common hypothesis in the design of internal combustion engine exhaust lines, namely that the ratio of the total pressure drop across the line to the inlet dynamic head should be a function only of the Reynolds number. While incompressible flow theory, provided that some simplifications are considered, is often used in support of this hypothesis, detailed experimental verification in actual exhaust lines is absent from the literature. Production exhaust lines contain non-trivial flow complexities such as muffler devices and catalytic converters and, in the case of high-performance engines, often operate at high temperature and high mass flow conditions, thereby rendering the usual theoretical simplifications doubtful. In this work, a production exhaust line composed of cold and hot ends, featuring a muffler and a catalytic converter, is tested at a variety of conditions. Analysis of the results shows that compressibility corrections must be factored in at certain conditions routinely found in actual high-performance engines, and that for hot ends, laminar flow at the converter monolith channels may pose a challenge to the hydrodynamic similarity hypothesis., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), [FEDER-ICTS-2012-06]" framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. F. Roig is supported through the Programa de Apoyo para la Investigation y Desarrollo of the Universitat Politecnica de Valencia [PAID-01-17]
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Diesel ignition delay and lift-off length through different methodologies using a multi-hole injector

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Viera Sotillo, Alberto Antonio
  • Manin, Julien
In this paper, lift-off length has been measured via both broadband luminosity and OH chemiluminescence. In addition, ignition delay has also been measured via broadband chemiluminescence and Schlieren imaging. A 3 orifice injector from the Engine Combustion Network (ECN) set, referred to as Spray B, and a single component fuel (n-dodecane) was used. Experiments were carried out in a constant flow and pressure facility, that allowed to reproduce engine-like thermodynamic conditions, and enabled the study to be performed over a wide range of test conditions with a very high repetition rate. Data obtained was also compared with results from a single orifice injector also from the Engine Combustion Network, with analog orifice characteristics (90 lm outlet diameter and convergent shape) and technology as the injector used. Results showed that there is good correlation between the ignition delay measured through both methodologies, that oxygen concentration and injection pressure plays a minor role in the ignition delay, being ambient temperature and density the parameters with the highest influence. Lift-off length measurements showed significant differences between methodologies. Minor deviation was observed between injectors with different nozzle geometry (seat inclination angle), due to temperature variations along the chamber, highlighting the importance of temperature distribution along combustion vessels. Empirical correlations for lift-off and ignition delay were calculated, underlining the effect of the conditions on the parameters studied. Coefficients of the correlations were compared with results for the single orifice injector, this showed that variations of test conditions have the same impact on ignition delay and lift-off length regardless the nozzle orifice configuration., This work was sponsored by "Ministerio de Economia y Competitividad" of the Spanish Government in the frame of the Project "Comprension de la influencia de combustibles no convencionales en el proceso de injeccion y combustion tipo Diesel", Reference TRA2012-36932. Additionally, the optical equipment used for the project was purchased with funding from Ministerio de Economia y Competitividad FEDER-ICTS-2012-06.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modal decomposition of the unsteady flow field in compression-ignited combustion chambers

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] In this paper, the unsteady behaviour of a compression-ignited (CI) engine combustion chamber is studied by analysing the results of a Computational Fluid Dynamics (CFD) model through the application of different flow decomposition techniques, aiming to resolve the underlying modal structure of the process. Experimental validation for the combustion simulation is provided, and a methodology for extracting coherent pressure information is proposed in order to provide a suitable input for different analysis methods. These range from straightforward Fourier transform techniques to more sophisticated modal decomposition approaches. In particular Proper Orthogonal Decomposition (POD) is shown to provide valuable insight into the time-spatial structure of the combustion flow field, allowing the establishment of correlations between pressure modes and physical parameters of the combustion, such as the injection timing or the chamber geometry. Dynamic Mode Decomposition (DMD) on the other hand is proven to successfully highlight the link between the frequency of the unsteady energy components and their spatial distribution within the chamber. Advantage is then taken of the modal characterization of the unsteady behaviour in the chamber to showcase how physical parameters such as the spray angle can be modified to optimize the acoustic signature of the combustion process, helping CI internal combustion engines reduce their acoustic environmental impact (C) 2017 The Combustion Institute. Published by Elsevier Inc. All rights reserved., The equipment used in this work has been partially supported by FEDER project funds "Dotacidn de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT)" [grant number FEDER-ICTS-2012-06], framed in the operational program of unique scientific and technical infrastructure of the Spanish Government.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Methodology for Phase Doppler Anemometry Measurements on a Multi-Hole Diesel Injector

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • GIRALDO-VALDERRAMA, JHOAN SEBASTIAN
[EN] In this paper, a methodology for Phase Doppler Anemometry (PDPA) measurements on a multi-hole diesel injector is developed. Several key considerations were taken into account in this methodology: The windows for PDPA optical access must be clean, since fuel impregnated in these could preclude the droplets velocity acquisition. Some parts, including a device for spray isolation, were designed and manufactured to fulfill this goal. Taking into account that only one spray is measured, the isolation device captures all except three of the sprays (including the spray of interest). The two plumes accompanying the main spray were thought to conserve the actual air entrainment and thus the spray behavior. The spray of interest was aligned horizontally to ease the way that the PDPA measurements are carried out. The plume was lined up by means of the MIE-Scattering macroscopic optical technique. Images were acquired for several injection events and spray contours were detected and processed with a purpose-built Matlab tool. At each time step a spray axis inclination was estimated using the centroids from instantaneous contours. Also, preliminary droplet velocity measurements were made to check the effectiveness of the alignment and spray isolation strategies. Both geometrical characterization and spray alignment had very low measurement error. Radial velocity profiles show that PDPA measurements with this set-up configuration preserved the spray behavior., This research was performed in the frame of the project "Estudio de la interaccion chorro-pared en condiciones realistas de motor" reference TRA2015-67679-c2-1-R from Ministerio de Economia y Competitividad (Spanish Ministry of Economy). The equipment used in this work has been partially supported by FEDER Project funds "Dotacion de infraestructuras cientifico tectinas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", framed in the operation program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. Jhoan S. Giraldo was supported by a research grant from Generalitat Valenciana (Programa Santiago Grisolia, GRISOLIA/2013/007).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of the injection conditions influence over n-dodecane and diesel sprays with two ECN single-hole nozzles. Part I: Inert atmosphere

  • Gimeno, Jaime|||0000-0003-3317-9994
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Peraza, Jesús E
In this research, two Engine Combustion Network (ECN) mono-orifice nozzles, referred to as Spray C and Spray D. respectively, were analyzed by performing visualization tests through Schlieren and Diffused Backlight Illumination (DBI) techniques under a wide range of ambient conditions in a non-reactive atmosphere. Spray C presents a straight nozzle designed with a sharp fillet in opposition to Spray D that has similar hydraulic properties, but with a convergent nozzle construction and a smoother corner. The experiments were carried out injecting two distinct fuels at different injection pressure ranges, from 50 MPa to 150 MPa with n-dodecane and to 200 MPa for diesel. The images were processed with Matlab home-built routines to calculate parameters as spray penetration, spreading angle, quasi steady liquid length, as well as the spray penetration derivative respect to the square root of time, presented in this document as R-parameter. The results showed a clear influence of nozzle geometry in all measured parameters, due mainly to the nature of Spray C to cavitation, which increase the spreading angle and consequently a reduction in vapor penetration. On the other hand, fuel properties also affected spray penetration due to its dependency on viscous forces expressed in terms of the Reynolds number and its volatility in case of liquid length. This last parameter was calculated employing two processing methodologies, finding a good general agreement between them., This work was supported by "Ministerio de Economia y Competitividad" of the Spanish Government in the frame of the projects "Estudio de la interaccion chorro-pared en condiciones realistas de motor", Ref. TRA2015-67679-c2-1-R. Moreover, the optical equipment employed in the project was purchased with investment from "Ministerio de Economia y Competitividad" FEDER-ICTS-2012-06.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical simulation of primary atomization in diesel spray at low injection pressure

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Romero, José-Vicente|||0000-0003-3366-6557
  • Roselló, María-Dolores|||0000-0002-5724-7683
  • Jaramillo-Císcar, David
[EN] Atomization involves complex physical processes and gas liquid interaction. Primary atomization on diesel spray is not well understood due to the difficulties to perform experimental measurements in the near nozzle field. Hence computational fluid dynamics (CFD) has been used as a key element to understand and improve diesel spray. A recent new code for incompressible multiphase flow with adaptive octree mesh refinement has been used to perform simulations of atomization at low injection pressure conditions. The multiphase flow strategy to manage different flows is the volume of fluid (VOF) method. The adaptive mesh allows to locally refine the mesh at each time step where a better resolution is needed to capture important gradients instead of using a static mesh with a fixed and high number of cells which, in turn, would lead to an unaffordable computational cost. Even with this approach, the cell number is very high to achieve a Direct Numerical Simulation (DNS) at reasonable computational cost. To reduce the computational cost, an idea has been explored, the possibility of setting a maximum number of cells of the domain. Following this idea, the code has been tested with different configurations to understand their effects on numerical stability, the change in different spray parameters and the benefits achieved in terms of execution time. The outcomes have been validated against a theoretical model., This work was sponsored by "Ministerio de Economa y Competitividad" of the Spanish Government in the frame of the Project "Comprensin de la influencia de combustibles no convencionales en el proceso de injeccin y combustin tipo diesel", Reference TRA2012-36932 and MTM2013-41765-P. Additionally, the hardware used for the project was purchased with funding from Ministerio de economia y competitividad FEDER-ICTS-2012-06. The authors would also like to thank the computer resources, technical expertise and assistance provided by the Universitat de Valencia in the use of the supercomputer "Tirant".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of gasoline and Diesel blends on combustion noise and pollutant emissions in Premixed Charge Compression Ignition engines

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Monico Muñoz, Luisa Fernanda
[EN] Research efforts in the automotive sector focus on developing new combustion concepts for mitigating the emissions of nitrous oxides and soot of conventional Diesel combustion. One of the most promising concept is the Premixed Charge Compression Ignition. In this, the fuel burns in premixed conditions, avoiding the formation of soot whereas nitrous oxides are controlled using large amounts of exhaust gas recirculation. Because of the premixed combustion, high fuel-burning velocities are produced, whence combustion noise is deteriorated. In order to mitigate this drawback, different blends of gasoline and Diesel fuels are being considered due to their suitability for this combustion characteristics. The effect of these fuel blends on emissions, performance and engine noise is analysed in this paper with the aim to provide additional knowledge of the fundamental issues of this particular combustion mode. The study also includes sweeps of both the start of injection and the amount of exhaust gas recirculation, in order to evaluate further degrees of freedom in the optimisation of the engine settings. Results show that the consideration of the engine noise together with both performance and emissions, reduces dramatically the margin of variation of the combustion settings, limiting therefore the operation range of the engine. (C) 2017 Elsevier Ltd. All rights reserved., The equipment used in this work has been partially supported by the Spanish Ministerio de Economía y Competitividad through grant no DPI2015-70464-R and by FEDER project funds Dotación de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06) framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economía y Competitividad. J. Gomez-Soriano is partially supported through contract FPI-S2-2016-1353 of the Programa de Apoyo para la Investigación y Desarrollo (PAID-01-16) of Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of dual spray injectors for optimising the noise emission of gasoline partially premixed combustion in a 2-stroke HSDI CI engine

  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] This paper evaluates the potential advantages of introducing a new injector concept with a dual set of orifices in a 2-stroke engine operating with gasoline partially premixed combustion (PPC gasoline), specially in terms of combustion noise reduction. The injector is based on a configuration with two concentric needle valves and dual actuators, which allows to switch among two independent crowns of holes. The first set of orifices is controlled by the primary needle valve while an additional needle valve manages the secondary holes crown. Moreover, both valves are coupled with the two actuators separately, providing enhanced selective control over injection with an extra degree of freedom. In this investigation, a combination of Computational Fluid Dynamics (CFD) simulations and the Design of Experiments (DoE) technique is proposed with the specific purpose of optimizing this new injector configuration. In addition to determining the most convenient design, this method is extremely useful to establish cause/effect relationships between the injection design parameters and their impact on the engine performance and emissions. Results show how this solution could increase the operating range of the PPC gasoline concept by improving the combustion stability while acoustic emissions are reduced, The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" from the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of swirl on in-cylinder heat transfer in a light-duty diesel engine

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Salvador-Iborra, Josep
  • Warey, Alok
[EN] One of the key strategies to reduce CO2 emissions is to improve the efficiency of engines in order to diminish fuel consumption. A way to increase engine efficiency is to reduce the heat losses. Internal heat transfer in engines depends on combustion chamber conditions. Swirl is an important parameter for combustion that also changes in-cylinder variables relevant to heat transfer. In this work, influence of swirl on combustion chamber heat fluxes was investigated employing wall temperature data and a 0-D thermal model. Local wall temperatures were measured at various locations of the cylinder liner and the cylinder head using thermocouples. A sweep of swirl ratios was carried out at different engine operating conditions. It was observed that the effect of swirl effect was highly dependent on location and was more important near the center of the firedeck. Results from the 0-D thermal model were evaluated by comparing measured and predicted wall temperatures. Using a convenient arrangement of thermocouples and the 0-D thermal model, it was possible to calculate heat flux from combustion chamber to cylinder walls. By analyzing heat flux through the firedeck, an increase in heat losses between 4 and 12% was observed for each unit that swirl number was increased. Results from the 0-D thermal model indicate that similar effects occur for other surfaces in the combustion chamber. (C) 2016 Elsevier Ltd. All rights reserved., The authors acknowledge General Motors Global R&D for supporting this research. The equipment used in this work was partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of combustion acoustic phenomena in compression-ignition engines using large eddy simulation

  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Pal, P.
[EN] As computational capabilities continue to grow, exploring the limits of computational fluid dynamics to capture complex and elusive phenomena, which are otherwise difficult to study by experimental techniques, is one of the main targets for the research community. This paper presents a detailed analysis of the physical processes that lead to combustion noise emissions in internal combustion engines. In particular, diesel combustion in a compression-ignition (CI) engine is studied in order to understand the singular behavior of the in-cylinder flow field responsible for the acoustic emissions. The main objective is, therefore, to improve the understanding of the phenomena involved in CI engine noise using large eddy simulations. Several visualization methods are employed to investigate the connection between combustion behavior and its effects on the pressure field. In addition, proper orthogonal decomposition is used to analyze the modal energy distribution among all the acoustic modes. The results show that the acoustic signature is fundamentally conditioned by the intensity of the premixed combustion rather than by the pressure oscillations generated by turbulent fluctuations in the flame surface established during the diffusion stage., The submitted manuscript was created partly by UChicago Argonne, LLC, Operator of Argonne National Laboratory. Argonne, a U.S. Department of Energy Office of Science laboratory, is operated under Contract No. DE-AC02-06CH11357. This research was partly funded by the U.S. DOE Office of Vehicle Technologies, Office of Energy Efficiency and Renewable Energy, under Contract No. DE-AC02-06CH11357. The authors wish to thank Gurpreet Singh and Michael Weismiller, program managers at the DOE, for their support. In addition, the authors would like to acknowledge the Laboratory Computing Resource Center (LCRC) at the Argonne National Laboratory for computing time on the Bebop cluster that was used in this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Acoustic characterization of automotive turbocompressors

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Tíscar, Jorge|||0000-0003-4934-4587
The performance of different experimental techniques proposed in the literature for acoustic characterization was assessed through the study of the noise generated by the compressor of an automotive turbocharger under different working conditions in an engine test cell. The most critical restrictions of in-duct intensimetry methods regarding frequency limitations are presented and experimentally demonstrated. The results provided by those methods were correlated against a reference intensity probe. A beamforming method based on three-sensor-phased arrays appears to be the most reliable approach in the plane wave range, presenting higher accuracy than the more common two-microphone method and simple pressure level measurements. Also, preliminary results from a novel radiated noise quantification technique based on acoustic particle velocity are presented and discussed. The results indicate that further research on this topic is required., This work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant no. TRA2012-36954. The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06),'' framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic Characterization of Diesel Engine Single-Hole Injectors

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Cuisano, J.
  • Arco, J.
Due to world trend on the emission regulations and greater demand of fuel economy, the research on advanced diesel injector designs is a key factor for the next generation diesel engines. For that reason, it is well established that understanding the effects of the nozzle geometry on the spray development, fuel-air mixing, combustion and pollutants formation is of crucial importance to achieve these goals. In the present research, the influence of the injector nozzle geometry on the internal flow characteristics is studied. For this purpose, ten single-hole diesel injectors differing in the orifices degree of conicity (five cylindrical, five conical) but with similar nozzle flow capacity have been characterized geometrically (measurements of nozzle outlet section) and hydraulically. The mass flow and momentum flux rates have been measured for a wide range of experimental conditions. Special attention is given to study the cavitation phenomenon since the cylindrically-shaped nozzle orifices are expected to propitiate cavitation due to abrupt changes in flow direction. The study has been carried out with two different fuels: n-dodecane and commercial diesel, thereby the effect of the fuel properties is also analyzed. The results show that the measured nozzle outlet diameters are higher than the nominal specification for both nozzle types. As expected, the onset of cavitation on the cylindrical nozzles has been identified causing a reduction on the injected mass for all tested conditions. The effective diameter for the cylindrical nozzles have been found to be around 175 mu m (geometrical diameter approximate to 212 mu m) and around 185 mu m (geometrical diameter approximate to 191 mu m) for the conical ones. Finally, the higher density of diesel with respect to n-dodecane have resulted on mass flow rates around 8% over the n-dodecane values for the same test conditions., This work was sponsored by "Ministerio de Economia y Competitividad" of the Spanish Government in the frame of the Project "Estudio de la interaccion chorro-pared en condiciones realistas de motor", Reference TRA2015-67679-c2-1-R. Additionally, the hardware used for the project was purchased with funding from Ministerio de economia y competitividad FEDER-ICTS-2012-06. Julio Cuisano E. was financed by a postdoctoral fellowship from Fundacion Carolina and Pontifica Universidad Catolica del Peru.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Laser induced plasma methodology for ignition control in direct injection sprays

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio
  • Pinotti, Mattia
New combustion modes for internal combustion engines represent one of the main fields of investigation for emissions control in transportation Industry. However, the implementation of lean fuel mixture condition and low temperature combustion in real engines is limited by different unsolved practical issues. To achieve an appropriate combustion phasing and cycle-to-cycle control of the process, the laser plasma ignition system arises as a valid alternative to the traditional electrical spark ignition system. This paper proposes a methodology to set-up and optimize a laser induced plasma ignition system that allows ensuring reliability through the quantification of the system effectiveness in the plasma generation and positional stability, in order to reach optimal ignition performance. For this purpose, experimental tests have been carried out in an optical test rig. At first the system has been optimized in an atmospheric environment, based on the statistical analysis of the plasma records taken with a high speed camera to evaluate the induction effectiveness and consequently regulate and control the system settings. The same optimization method has then been applied under engine-like conditions, analyzing the effect of thermodynamic ambient conditions on the plasma induction success and repeatability, which have shown to depend mainly on ambient density. Once optimized for selected engine conditions, the laser plasma induction system has been used to ignite a direct injection Diesel spray, and to compare the evolution of combustion with that of a conventional auto-ignited Diesel spray., The authors acknowledge that this research work has been partly funded by the Government of Spain under the project HiReCo TRA2014-58870-R and grant BES-2015-072119. The equipment used in this work has been partially supported by FEDER project ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental analysis of cyclical dispersion in compression-ignited versus spark-ignited engines and its significance for combustion noise numerical modeling

  • Broatch, A.|||0000-0001-9991-1039
  • López, J. Javier|||0000-0002-9486-2511
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] As noise pollution remains one of the biggest hurdles posed by thermal engines, increasing efforts are made to alleviate the generation of combustion noise from the early design stage of the chamber. Since the complexity of both modern chamber geometries and the combustion process itself precludes robust analytic solutions, and since the resonant, highly 3D pressure field is difficult to be measured experimentally, focus is put on the numerical modelling of the process. However, in order to optimize the resources devoted to this simulation, an informed decision must be made on which formulations are followed. In this work, the experimental cyclic dispersion of the in-cylinder pressure is analyzed in two typical compression-ignited (CI) and spark-ignited (SI) engines. Acoustic signatures and pressure rise rates are derived from this data, showing how while the preponderance of flame front propagation and dependency of previous cycle in SI engine noise usually calls for multi-cycle, more complex turbulence modelling such as Large Eddy Simulation (LES), simpler Unsteady Reynolds-Averaged Navier-Stokes (URANS) formulations can accurately characterize the more consistent pressure spectra of CI thermal engines, which feature sudden autoignition as the main noise source., European Regional Development Fund (Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte, CiMeT) (FEDER-ICTS-2012-06). Programa de Apoyo para la Investigacion y Desarrollo (PAID) Universitat Politecnica de Valencia (FPI-S2-2016-1353).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the combined effect of hydrogrinding process and inclination angle on hydraulic performance of diesel injection nozzles

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • Jaramillo Císcar, David
  • Martínez López, Jorge
A computational study to investigate the influence of the orifices inclination and the rounding radius at the orifice inlet (consequence of the hydro-erosive grinding process applied after the orifices machining) over the internal nozzle flow is performed in this paper. The study starts with the analysis of experimental results where the mass flow and momentum flux of two nozzles with very different values of these two variables are compared. This analysis shows relatively small differences in terms of mass flow and momentum flux, since the higher losses associated to the higher deflection of the streamlines with a higher inclination of the orifices are counteracted by the higher rounding radius, which favors the flow entrance to the orifice. To explain this experimental outcome, an extensive computational study involving nine geometries that combine different inclination angles and rounding radius is conducted, in order to quantify the influence of both parameters on the flow separately, as well as to assess the potential of their combination. These geometries are compared in terms of discharge coefficient, critical cavitation conditions and effective injection velocity, among others. Results show differences up to 15% in terms of mass flow rate and 8% for the effective injection velocity among the two extreme cases (lowest inclination and highest hydro-erosion level versus the nozzle with the highest inclination and lowest hydro-erosion level). Given the importance of these phenomena on the subsequent mixing and combustion processes, the results hereby presented are of interest for Diesel engines injectors and combustion chambers designers., This work was partly sponsored by "Ministerio de Economia y Competitividad" in the frame of the project "Comprension de la influencia de combustibles no convencionales en el proceso de inyeccion y combustion tipo diesel", Reference TRA2012-36932. The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", in the frame of the operation program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical and experimental analysis of automotive turbocharger compressor aeroacoustics at different operating conditions

  • Broatch Meza, Alberto
  • Galindo, José|||0000-0001-6068-182X
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Tíscar, Jorge|||0000-0003-4934-4587
Centrifugal compressor aeroacoustics are analyzed by means of a three-dimensional CFD model. Three operating points at nominal compressor speed are simulated ranging from best efficiency point to near-surge conditions. Experimental measurements are obtained using a steady flow rig mounted on an anechoic chamber. URANS and DES predictions of compressor global variables and pressure spectra are compared against experimental measurements. Flow-induced noise increases as the operating point moves toward surge line. Stall at the suction side of the blades exists even for high mass flow conditions, causing a high frequency boundary layer oscillation. Low momentum cells rotating at the diffuser are found at points closer to surge, causing the so-called whoosh noise. Inducer rotating stall is also present at these conditions. Point closest to surge shows a rotating tornado-type vortex at the inducer, determining a moving low pressure region that increases low frequency noise content., The equipment used in this work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant no. TRA2012-36954 and by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. Part of the computational resources used in this work have been provided by Super computing Center of Universitat Politecnica de Valencia and are thus gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

New European Driving Cycle assessment by means of particle size distributions in a light-duty diesel engine fuelled with different fuel formulations

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Luján, José M.|||0000-0001-6133-8943
  • Ruiz-Rosales, Santiago|||0000-0001-9536-3696
  • Campos, Daniel
  • Linares Rodríguez, Waldemar Gregorio
In this study, an experimental investigation of particle size distribution emission over performance of transient conditions in a high speed diesel engine fuelled with diesel, biodiesel and Fischer Tropsch fuels have been assessed. Six fuels with different properties have been tested in a 4-cylinder light-duty diesel engine typically used for European passenger cars. The cycle used in this study was the New European Driving Cycle (NEDC) and each test was carried out after a stabilization warming period in order to avoid cold start effects. A comparative analysis between nucleation and accumulation particle mode concentration, particle size distributions and a geometric mean diameter calculation are presented in this paper. In this sense, a reduction in the range of particle diameter emitted and a decrease in accumulation particle mode concentration with Fischer Tropsch fuel during the EUDC were found. In contrast, all biofuels used show an increase of particle number concentration in nucleation-mode during the urban cycles (ECE-15) related to combustion damage at low load conditions. Finally, an increase in the sulfur content diesel fuel leads to an increase in the geometric mean diameter of particle size distribution related to the increase in accumulation particle concentration during the entire cycle., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)'', framed in the operational program of singular scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental analysis on the influence of nozzle geometry over the dispersion of liquid n-dodecane sprays

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Viera-Sotillo, Juan Pablo
[EN] Understanding and controlling mixing and combustion processes is fundamental in order to face the challenges set by the ever more demanding pollutant regulations and fuel consumption standards of direct injection diesel engines. The fundamentals of these processes haven been long studied by the diesel spray community from both experimental and numerical perspectives. However, certain topics, such as the influence of nozzle geometry over the spray atomization, mixing, and combustion process, are still not completely well understood and predicted by numerical models. The present study seeks to contribute to the current understanding of this subject, by performing state of the art optical diagnostics to liquid sprays injected through two singe-hole nozzles of different conicity. The experiments were carried out in a nitrogen-filled constantpressure-flow facility. Back pressures were set to produce the desired engine-like density conditions in the chamber, at room temperature. The experimental setup consists in a diffused back-illumination setup with a fast pulsed LED light source and a high-speed camera. The diagnostics focused on detecting the liquid spray contour and evaluating the influence of nozzle geometry over the time-resolved and quasi-steady response of the spray dispersion, at similar injection conditions. Results show a clear influence of nozzle geometry on spray contour fluctuations, where the cylindrical nozzle seems to produce larger dispersion in both time-resolved fluctuations and quasi-steady values, when compared to the conical nozzle. This evidences that the turbulence and radial velocity profiles originated at the cylindrical nozzle geometry are able to affect not only the microscopic scales inside the nozzle, but also macroscopic scales, such as the steady spray. Observations from this study indicate that the effects of the flow characteristics within the nozzle are carried on to the first millimeters of the spray, in which the rest of the spray formation downstream is pre-defined., This work was sponsored by Ministerio de Economía y Competitividad of the Spanish Government in the frame of the Project “Comprensión de la influencia de combustibles no convencionales en el proceso de inyección y combustión tipo diesel,” Reference TRA2012-36932. Additionally, the optical equipment used for the project was purchased with funding from Ministerio de Economía y Competitividad FEDER-ICTS-2012-06. The authors would finally like to thank José Enrique Del Rey and María del Carmen Tomás for their collaboration in the setup of the experiments and laboratory work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the shift of acoustic characteristics of compression-ignited engines when operating with gasoline partially premixed combustion

  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] As the focus of research and development is put into innovative combustion concepts with the goal of reducing harmful chemical pollutants while keeping or even improving the efficiency of conventional Diesel combustion, it is necessary to consider the impact on noise pollution brought by those innovative concepts. However, the question arises as to what extent the noise characterization and optimization strategies currently applied to conventional Diesel compression-ignited engines are applicable to these innovative combustion concepts. In this paper, we apply experimental noise characterization techniques based on pressure trace decomposition to two compression-ignited engines: a baseline conventional Diesel engine and an innovative 2-stroke engine operating with the gasoline partially premixed combustion concept. Analysis of the results reveals that the underlying physical phenomena responsible for the spectral signature of the noise are still shared between the new and the conventional concepts. However, results evince a significant change in the relevance of these physical sources, leading to necessary changes in optimization strategies for future compression-ignited engine development., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT)" [Grant No. FEDER-ICTS-2012-06], framed in the operational program of unique scientific and technical infrastructure of the Spanish Government. J. Gomez-Soriano is partially supported through the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia [Grant No. FPI-S2-2016-1353]
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fuel temperature influence on the performance of a last generation common-rail diesel ballistic injector. Part I: Experimental mass flow rate measurements and discussion

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Carreres, Marcos|||0000-0001-6430-6613
  • Crialesi Esposito, Marco
An experimental study is conducted in this paper in order to assess the influence of the fuel temperature on the performance of a last generation common-rail ballistic solenoid injector. Mass flow rate measurements are performed for a wide range of temperatures, extending from 253 to 373 K, representative of all the possible operating conditions of the injector in a real diesel engine, including cold start. The high pressure line and the injector holder were refrigerated, making it possible to carefully control the fuel temperature, whereas measurements at cold conditions were carried out with the help of a climatic chamber. Relevant features such as stationary mass flow, injection delay or the behaviour at the opening and closing stages are analysed together with parameters governing the flow, such as the injector discharge coefficient. Results show an important influence of the fuel temperature, especially at low injection pressure. A low injection temperature results in a lower stationary mass flow rate, whereas injection duration is also reduced. These results will be explained mainly through the fuel properties variation induced by temperature, together with the ballistic nature of the injector used for the study. A second part of the paper introduces a one-dimensional model that makes it possible to reproduce these results and further explain them through the analysis of other relevant variables, such as the needle lift., This work was partly sponsored by "Ministerio de Economia y Competitividad" (Spain) in the frame of the project "Comprension de la influencia de combustibles no convencionales en el proceso de inyeccion y combustion tipo diesel", reference TRA2012-36932. The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", in the frame of the operation program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Near field visualization of diesel spray for different nozzle inclination angles in non-vaporizing conditions

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Viera-Sotillo, Alberto Antonio
[EN] Accurate experimental data are often needed to validate computational fluid dynamics models. These models regularly rely on experimental results from single-orifice axially drilled nozzles that do not fully represent real injectors, as the difference in inclination angles creates turbulent conditions at the nozzle outlet, consequences of which on the spray development are not yet fully understood. In this work, near-field visualization was done for two nozzle inclination angles in non-vaporizing conditions. Spray tip penetration, spreading angle, and axis angle fluctuations are reported. Three hypotheses are analyzed: liquid jet breakup mechanism, internal flow development, and cavitation. Experiments were carried out using n-Dodecane, testing a single orifice axially drilled and a three-orifice injector, from the Engine Combustion Network. The spray was observed with a diffused back-illumination technique and a long distance microscope, only visualizing the first 6 mm of spray tip penetration, for three injection pressures and four gas densities at ambient temperature. The multi-orifice injector produced a spray with wider spreading angle, which resulted in smaller penetration values. Additionally, higher spray axis angle fluctuations were observed for the multi-orifice injector, which increased for higher injection pressure and, to a lesser extent, with decreasing chamber density. Further analysis was performed with spreading angle fluctuations measurements, where results showed good agreement with spray axis angle fluctuations trends, implying that complex internal flow structures, and even incipient cavitation, could be present in the multi-orifice injector and be the cause of these spray axis angle fluctuations., This work was sponsored by "Ministerio de Economia y Competitividad" of the Spanish Government in the frame of the project " Estudio de la interaccion chorro-pared en condiciones realistas de motor," reference TRA2015-67679-c2-1-R. Additionally, the optical equipment used for the project was purchased with funding from Ministerio de Economia y Competitividad FEDER-ICTS-2012-06.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of tip clearance on flow behavior and noise generation of centrifugal compressors in near-surge conditions

  • Galindo, José|||0000-0001-6068-182X
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Navarro, Roberto|||0000-0003-2587-4954
  • López Hidalgo, Miguel Andrés
CFD has become an essential tool for researchers to analyze centrifugal compressors. Tip leakage flow is usually considered one of the main mechanisms that dictate compressor flow field and stability. However, it is a common practice to rely on CAD tip clearance, even though the gap between blades and shroud changes when compressor is running. In this paper, sensitivity of centrifugal compressor flow field and noise prediction to tip clearance ratio is investigated. 3D CFD simulations are performed with three different tip clearance ratios in accordance to expected operating values, extracted from shaft motion measurements and FEM predictions of temperature and rotational deformation. Near-surge operating conditions are simulated with URANS and DES. DES shows superior performance for acoustic predictions. Cases with reduced tip clearance present higher pressure ratio and isentropic efficiency, but no significant changes in compressor acoustic signature are found when varying clearance. In this working point, tip clearance is immersed in a region of strongly swirling backflow. Therefore, tip leakage cannot establish any coherent noise source mechanism., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. The authors wish to thank Mr. Pau Raga for his worthy assistance during the meshing process.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational Methodology for Knocking Combustion Analysis in Compression-Ignited Advanced Concepts

  • Serrano, J.R.|||0000-0003-0692-3917
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Martínez-Hernándiz, Pablo José
[EN] In the present work, a numerical methodology based on three-dimensional (3D) computational fluid dynamics (CFD) was developed to predict knock in a 2-Stroke engine operating with gasoline Partially Premixed Combustion (PPC) concept. Single-cycle Unsteady Reynolds-Averaged Navier Stokes (URANS) simulations using the renormalization group (RNG) k - epsilon model were performed in parallel while the initial conditions are accordingly perturbed in order to imitate the variability in the in-cylinder conditions due to engine operation. Results showed a good agreement between experiment and CFD simulation with respect to cycle-averaged and deviation of the ignition timing, combustion phasing, peak pressure magnitude and location. Moreover, the numerical method was also demonstrated to be capable of predicting knock features, such as maximum pressure rise rate and knock intensity, with good accuracy. Finally, the CFD solution allowed to give more insight about in-cylinder processes that lead to the knocking combustion and its subsequent effects., The work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant number TRA2016-79185-R. The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" from the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. In addition, J. Gomez-Soriano is partially supported by an FPI contract (FPI-S2-2016-1353) of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-16)" of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An Experimental Study on Diesel Spray Injection into a Non-Quiescent Chamber

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Micó, Carlos|||0000-0001-5787-6212
  • Zhong, Wenjun
  • Xuan, Tiemin
[EN] Visualization of single-hole nozzles into quiescent ambient has been used extensively in the literature to characterize spray mixing and combustion. However in-cylinder flow may have some meaningful impact on the spray evolution. In the present work, visualization of direct diesel injection spray under both non-reacting and reacting operating conditions was conducted in an optically accessible two-stroke engine equipped with a single-hole injector. Two different high-speed imaging techniques, Schlieren and UV-Light Absorption, were applied here to quantify vapor penetration for non-reacting spray. Meanwhile, Mie-scattering was used to measure the liquid length. As for reacting conditions, Schlieren and OH* chemiluminescence were simultaneously applied to obtain the spray tip penetration and flame lift-off length under the same TDC density and temperature. Additionally, PIV was used to characterize in-cylinder flow motion. Results were compared with those from the Engine Combustion Network database obtained under quiescent ambient conditions in a high pressure high temperature vessel. Because of the air flow induced by piston movement, in-cylinder conditions in the two-stroke engine during the spray injection are highly unsteady, which has a significant impact on the spray development and interference on the spray visualization. From the comparison with quiescent data from the Engine Combustion Network, air flow induced by piston movement was found to slow down tip penetration. Moreover, both ignition delay and lift-off length under unsteady flow conditions show less sensitivity with ambient temperature than that of quasi-steady conditions., This work was partially funded by the Government of Spain through COMEFF Project (TRA2014-59483-R). In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. The authors want also to express their gratitude to CONVERGENT SCIENCE Inc for their kind support for this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Local flow measurements in a turbocharger compressor inlet

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Margot , Xandra|||0000-0002-2639-0444
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Narvekar, Y.
  • Cheung, R.
[EN] This paper describes an experimental study carried out with the objective of characterizing flow instabilities in turbocharger compressors, specially the distribution of the high-temperature compressed back flow that appears upstream of the impeller at marginal surge conditions. The inlet of a test compressor was fitted with linear and circumferential thermocouple arrays in order to measure the temperature distribution caused by this backflow, whose independence of duct wall temperature was validated through thermographic imaging. Miniaturized pressure probes at the inducer and diffuser showed how pressure spectra varied during the different operating conditions. In-duct acoustic intensity was measured in both the inlet and the outlet to investigate the correlation between a known super synchronous broadband issue known as whoosh noise and the backflow behaviour as characterized by local pressure and temperature. Analysis of the results points to inlet whoosh noise being boosted by this reversed flow but not caused by it, the source probably being located at or downstream of the compressor impeller., This work has been partially supported by Jaguar Land Rover Limited, Abbey Road, Whitley, Coventry CV3 4LF, UK. The equipment used in this work has been partially supported by the Spanish Ministerio de Economía y Competitividad through the grant no DPI2015-70464-R and by FEDER project funds “Dotaciön de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)” framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economía y Competitividad. J. García-Tíscar is partially supported through contract FPI-S2-2015-1530 of the Programa de Apoyo para la Investigación y Desarrollo (PAID) of Universitat Politécnica de Valéncia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical approach for assessing combustion noise in compression-ignited Diesel engines

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Gil, A.|||0000-0001-7192-6992
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] Diesel combustion noise has become a crucial aspect for the engine manufacturers due to its impact on human health and influence on the customer purchasing decision. The interaction of the pressure waves after mixture self-ignition induces cavity resonances inside the combustion chamber. This complex phenomenon produces high-frequency pressure oscillations, hence traditional in-cylinder measurements do not provide enough information to characterise the in-cylinder acoustic field. In this paper, a numerical methodology is proposed for assessing the Diesel combustion as a noise source and to overcome measurement limitations. An optimisation procedure is also presented in order to determine the numerical calculation parameters, boundary conditions definition and initialization. Results show that local flow conditions at the start of combustion have a strong influence on the acoustic response of the in-cylinder noise source. These particular conditions are only achievable by the proposed methodology which considers entire engine cycle simulations with the complete cylinder domain. Therefore, traditional Computational Fluid Dynamic (CFD) approaches, such those used for predicting combustion stability or pollutant emissions, are not suitable for reproducing the physical mechanisms of noise generation and they cannot be used for acoustic purposes. The reliability of the proposed methodology to simulate the acoustic field accurately inside the combustion chamber has been validated by comparison with experiments., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energdtica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. J. Gomez-Soriano is partially supported through the "Programa de Apoyo para la Investigacion y Desarrollo (PAID)" of Universitat Politecnica de Valencia [Grant No. FPI-S2-2016-1353].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of the nozzle holder on injected fuel temperature for experimental test rigs and its influence on diesel sprays

  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Carreres, Marcos|||0000-0001-6430-6613
  • Peraza, Jesús E
[EN] One of the test boundary conditions whose control is necessary for both experimental and numerical studies about the automotive engines research field is the temperature of the fuel inside the injector body during the injection. However, it is a difficult parameter to be directly measured in a non-intrusive way due to the injector architecture and the nature of the standard experiments that are done to characterize sprays. An experimental analysis is performed in this work employing a continuous flow test chamber, normally used in the optical diagnosis of diesel sprays, in order to compare and characterize two different designs for the nozzle holder of the test rig. The first one consisted in an aluminum holder that coats the nozzle until its tip, while the second one is made of steel and only supports the nozzle without covering it from the environment. The employed methodology was to set the test rig at a wide range of thermodynamic conditions inside the vessel such as ambient temperature and density and also the coolant temperature at the outlet of the injector casing for both cooling pieces. In this case, a dummy injector provided with a thermocouple was used to measure the tip temperature. In this way, correlations are obtained to estimate the injector body temperature out of the measurement points. Further experiments with a real single-hole diesel injector, controlling its tip temperature according to the previous results, are also discussed in this article in order to analyze the effect of this parameter on the spray evaporation process. Liquid length at inert conditions and both ignition delay and lift-off length at reactive ones were measured employing the same test vessel. All those parameters showed to be shortened with an increment of injected fuel temperature, and the lower the ambient temperature, the stronger this influence is., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was supported by "Ministerio de Economia y Competitividad" of the Spanish Government in the frame of the project "Estudio de la interaccion chorro-pared en condiciones realistas de motor (SPRAY WALL)," Ref. TRA2015-67679-c2-1-R. Moreover, the optical equipment employed in the project was purchased with investment from "Ministerio de Economia y Competitividad" FEDER-ICTS-2012-06 project. J.E.P. was supported through contract FPI-S2-2016-1362 of "Programa de Apoyo para la Investigacion y Desarrollo (PAID)" of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Application of optical diagnostics to the quantification of soot in n-alkane flames under diesel conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • Micó, Carlos|||0000-0001-5787-6212
  • Möller, Sebastian
  • García Martínez, Antonio
The present work pursues a twofold objective. On the one hand, the effect of fuel properties on soot formation has been analysed, under different engine operating conditions. On the other hand, sensitivity and performance of the three optical techniques has been evaluated, identifying their main advantages and drawbacks in the framework of the current study. LEM has been considered as the reference technique, as the measurement principle can be implemented without important limitations associated to the other two. Results highlight that larger molecules produce more soot than the smaller ones, with both reactivity and soot formation changing with the proportion of the heavier fraction. Despite describing similar trends, LEM and 2C do not provide the same KL values, with the pyrometry reaching some sort of saturation when increasing flame soot. A detailed analysis confirms that 2-Colar measurements are strongly biased by soot and temperature distribution inside the flame. Nevertheless, it could still be a good option for low sooting conditions. On the other hand, an attempt to calibrate LII signal by means of LEM measurements has been reported. This approach should make it possible to obtain additional information on the soot spatial distribution. However, inconsistencies have been identified which stem from the inherent limitations of LII technique in highly sooting conditions. (c) 2015 The Combustion Institute. Published by Elsevier Inc. All rights reserved., Authors wold like to acknowledge that part of this work has been funded by the Spanish Ministry of Science and Technology through project TRA2011-26359 and grant BES-2012-059721. Some other parts of this works were financially supported by "COMET K2 - Competence Centres for Excellent Technologies Programme" (project B03T02). In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06)", framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical Methodology for Optimization of Compression-Ignited Engines Considering Combustion Noise Control

  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Pinaki, Pal
  • Som, Sibendu
[EN] It is challenging to develop highly efficient and clean engines while meeting user expectations in terms of performance, comfort and drivability. One of the critical aspects in this regard is combustion noise control. Combustion noise accounts for about 40 percent of the overall engine noise in typical turbocharged diesel engines. The experimental investigation of noise generation is difficult due to its inherent complexity and measurement limitations. Therefore, it is important to develop efficient numerical strategies in order to gain a better understanding of the combustion noise mechanisms. In this work, a novel methodology was developed, combining computational fluid dynamics (CFD) modeling and genetic algorithm (GA) technique to optimize the combustion system hardware design of a high-speed direct injection (HSDI) diesel engine, with respect to various emissions and performance targets including combustion noise. The CFD model was specifically set up to reproduce the unsteady pressure field inside the combustion chamber, thereby allowing an accurate prediction of the acoustic response of the combustion phenomena. The model was validated by simulating several steady operating conditions and comparing the numerical results against experimental data, in both temporal and frequency domains. Thereafter, a GA optimization was performed with the goal of minimizing indicated specific fuel consumption (ISFC) and combustion noise, while restricting pollutant (soot and NOx) emissions to their respective baseline values. Eight design variables were selected pertaining to piston bowl geometry, nozzle inclusion angle, number of injector nozzle holes and in-cylinder swirl. An objective merit function based on the emissions, ISFC and combustion noise, was constructed to quantify the strength of the engine designs, and was determined using the CFD model as the function evaluator. The in-cylinder noise level was characterized by the total resonance energy of local pressure oscillations. The optimum engine configuration thus obtained, showed a significant improvement in terms of efficiency and combustion noise compared to the baseline system, along with both soot and NOx emissions within their respective constraints. This optimum configuration included a deeper and tighter bowl geometry with higher swirl and larger number of nozzle holes. Subsequently, a more detailed acoustics analysis based on proper orthogonal decomposition (POD) technique was carried out to further explore the combustion noise benefits achieved by the GA optimum. This computational study is a first of its kind (to the best of the authors¿ knowledge), which demonstrates a comprehensive framework to incorporate combustion noise into a numerical optimization strategy for engine design., The equipment used in this work was partially supported by FEDER and the Spanish Government through grant no. DPI2015-70464-R and by Fondo Europeo de Desarrollo Regional (FEDER) project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)," framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. J. Gomez-Soriano was partially supported through contract FPI-S2-2016-1353 of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-16)" of Universitat Politecnica de Valencia. The submitted manuscript was created partly by UChicago Argonne, LLC, Operator of Argonne National Laboratory. Argonne, a US Department of Energy (DOE) Office of Science laboratory, is operated under Contract No. DE-AC02-06CH11357. This research was partly funded by the US DOE Office of Vehicle Technologies, Office of Energy Efficiency and Renewable Energy under Contract No. DE-AC02-06CH11357. The authors wish to thank Gurpreet Singh and Leo Breton, program managers at DOE, for their support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A one-dimensional modeling study on the effect of advanced insulation coatings on internal combustión engine efficiency

  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Margot , Xandra|||0000-0002-2639-0444
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
[EN] This article presents a study of the impact on engine efficiency of the heat loss reduction due to in-cylinder coating insulation. A numerical methodology based on one-dimensional heat transfer model is developed. Since there is no analytic solution for engines, the one-dimensional model was validated with the results of a simple "equivalent" problem, and then applied to different engine boundary conditions. Later on, the analysis of the effect of different coating properties on the heat transfer using the simplified one-dimensional heat transfer model is performed. After that, the model is coupled with a complete virtual engine that includes both thermodynamic and thermal modeling. Next, the thermal flows across the cylinder parts coated with the insulation material (piston and cylinder head) are predicted and the effect of the coating on engine indicated efficiency is analyzed in detail. The results show the gain limits, in terms of engine efficiency, that may be obtained with advanced coating solutions., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The equipment used in this work has been partially supported by FEDER project funds "otacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT)'' (Grant No. FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Spanish Government. This project has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No. 724084.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Investigation of the effects of turbulence modeling on the prediction of compression-ignition combustion unsteadiness

  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Pal, P.
[EN] Adverse effects of global warming due to the greenhouse gas emissions is changing the actual paradigm for the use energy resources. In the absence of a mid-term solution for reducing these emissions in transportation, internal combustion (IC) engines are going to coexist in the social spheres in the foreseeable future. Therefore, the study of other IC engine-related problems remains relevant to ensuring the health of the society. In this investigation, a numerical methodology for comprehensive understanding of Noise, Vibration and Harshness in internal combustion engines is proposed. Due to its inherent complexity and lack of awareness, the main objective is to evaluate the impact of the turbulence modeling framework on the in-cylinder acoustic field recreation. Modal decomposition methods have been applied to isolate the coherent flow structures and to analyze how they change with the turbulence approach. Results demonstrate that the choice of the turbulence model is a critical aspect for noise modeling. Unsteady Reynolds-Averaged Navier-Stokes schemes predict a raw estimation of the internal acoustic field with the added value of being computationally less expensive. However, the use of more complex turbulence approaches such us large eddy simulation offers an accurate prediction of the acoustic structures and their cyclic dispersion., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT)'' [grant number FEDER-ICTS-2012-06], framed in the operational program of unique scientific and technical infrastructure of the Spanish Government. The submitted manuscript was created partly by UChicago Argonne, LLC, Operator of Argonne National Laboratory. Argonne, a U.S. Department of Energy Office of Science laboratory, is operated under Contract No. DE-AC02-06CH11357. This research was partly funded by U.S. DOE Office of Vehicle Technologies, Office of Energy Efficiency and Renewable Energy under Contract No. DE-AC0206CH11357.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Combustion noise analysis of partially premixed combustion concept using gasoline fuel in a 2-stroke engine

  • Broatch, A.|||0000-0001-9991-1039
  • Margot , Xandra|||0000-0002-2639-0444
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
In the last decade, different advanced combustion concepts based on generating totally or partially premixed conditions have been investigated in CI (compression ignition) engines with the aim of achieving lower NOx (nitrous oxides) and soot emissions. Most of the drawbacks inherent to this type of combustions, such as the combustion phasing control or combustion stability, can be mitigated by combining the PPC (Partially Premixed Combustion) concept fueled by gasoline and a small 2-stroke HSDI (high speed direct ignition) engine. However, combustion noise issue remains unsolved while it is a critical aspect due to its strong influence in the customer purchasing decision and compliance of more stringent regulations. In this work, an analysis of the combustion noise generated by PPC combustion concept is performed in order to identify the most influential parameters and to define key paths for controlling the noise level. In addition, 3D CFD (Computational Fluid Dynamics) simulations have been performed to further understand the combustion noise generation mechanisms. Results evidence how the strong impact of the maximum pressure time-derivative achieved during combustion process renders all other sources of noise generation irrelevant. The trade-off between combustion noise and combustion efficiency of this PPC concept has been confirmed, while the intrinsic relation between such parameters and the engine efficiency has been also evaluated., The authors kindly recognize the technical support provided by Mr. Pascal Tribotte from RENAULT SAS in the frame of the DREAM-DELTA-68530-13-3205 Project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dynamic mode decomposition of the acoustic field in radial compressors

  • Broatch, A.|||0000-0001-9991-1039
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Roig-Villanueva, Ferran
  • Sharma, Sidharath
[EN] Widely recognized since the beginning of air travel as a major issue, noise reduction remains nowadays a pressing concern for all stakeholders in the aviation industry. While aeroengine compressors, specially at the approach phase, have been historically identified as a leading source of noise, most of the research has been conducted on compressors of the axial type. However, radial compressors are found in a wide array of applications: smaller business jets, helicopters, unmanned aerial vehicles (UAVs), auxiliary power units (APUs), turbochargers for reciprocating engines, etc. Owing to their geometrical particularities, radial compressors feature flow patterns that differ from their axial counterparts, leading to different acoustic performance but also opening the door for different optimization approaches. Yet, classical modal decomposition techniques focused on duct propagation may fail to reveal the complex interactions between geometry and flow features that act as noise sources. In this paper we apply, in addition to the classical approach, a data-driven Dynamic Mode Decomposition (DMD) to pressure data coming from a Detached Eddy Simulation (DES), in which we have experimentally validated the correct reproduction of the modal behaviour of the compressor, thus obtaining in-depth details of the link between flow phenomena and noise generation and transmission across the inlet and outlet ducts. (C) 2019 Elsevier Masson SAS. All rights reserved., The equipment used in this work has been partially supported by the Spanish Ministerio de Economía y Competitividad through grant [DPI2015-70464-R] and by FEDER project funds Dotación de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), [FEDER-ICTS-2012-06] framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economía y Competitividad. F. Roig is supported through the Programa de Apoyo para la Investigación y Desarrollo of the Universitat Politècnica de València [PAID-01-17].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of turbulent model closure and type of inlet boundary condition on a Large Eddy Simulation of a non-reacting jet with co-flow stream

  • Payri, Raul|||0000-0001-7428-5510
  • López, J. Javier|||0000-0002-9486-2511
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Giraldo Valderrama, Jhoan Sebastián
[EN] In this paper, the behavior and turbulence structure of a non-reacting jet with a co-flow stream is described by means of Large Eddy Simulations (LES) carried out with the computational tool OpenFoam. In order to study the influence of the sub-grid scale (SGS) model on the main flow statistics, Smagorinsky (SMAG) and One Equation Eddy (OEE) approaches are used to model the smallest scales involved in the turbulence of the jet. The impact of cell size and turbulent inlet boundary condition in resulting velocity profiles is analyzed as well. Four different tasks have been performed to accomplish these objectives. Firstly, the simulation of a turbulent pipe, which is necessary to generate and map coherent turbulence structure into the inlet of the non-reacting jet domain. Secondly, a structured mesh based on hexahedrons has been built for the jet and its co-flow. The third task consists on performing four different simulations. In those, mapping statistics from the turbulent pipe is compared with the use of fluctuating inlet boundary condition available in OpenFoam; OEE and SMAG approaches are contrasted; and the effect of changing cell size is investigated. Finally, as forth task, the obtained results are compared with experimental data. As main conclusions of this comparison, it has been proved that the fluctuating boundary condition requires much less computational cost, but some inaccuracies were found close to the nozzle. Also, both SGS models are capable to simulate this kind of jets with a co-flow stream with exactitude., This research was performed in the frame of the project "Estudio de la interaccion chorro-pared en condiciones realistas de motor" reference TRA2015-67679-c2-1-R from Ministerio de Economia y Competitividad (Spanish Ministry of Economy). The equipment used in this work has been partially supported by FEDER Project funds "Dotacion de infraestructuras cientifico tectinas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", framed in the operation program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. Jhoan S. Giraldo was supported by a research grant from Generalitat Valenciana (Programa Santiago Grisolia, GRISOLIA/2013/007).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessing the optimum combustion under constrained conditions

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Blanco-Cavero, Diego
[EN] This work studies the optimum heat release law of a direct injection diesel engine under constrained conditions. For this purpose, a zero-dimensional predictive model of a diesel engine is coupled to an optimization tool used to shape the heat release law in order to optimize some outputs (maximize gross indicated efficiency and minimize NOx emissions) while keeping several restrictions (mechanical limits such as maximum peak pressure and maximum pressure rise rate). In a first step, this methodology is applied under different heat transfer scenarios without restrictions to evaluate the possible gain obtained through the thermal isolation of the combustion chamber. Results derived from this study show that heat transfer has a negative effect on gross indicated efficiency ranging from -4% of the fuel energy (m(f)H(v)), at high engine speed and load, up to -8% m(f)H(v), at low engine speed and load. In a second step, different mechanical limits are applied resulting in a gross indicated efficiency worsening from -1.4% m(f)H(v) up to -2.8% m(f)H(v) compared to the previous step when nominal constraints are applied. In these conditions, a temperature swing coating that covers the piston top and cylinder head is considered obtaining a maximum gross indicated efficiency improvement of +0.5% m(f)H(v) at low load and engine speed. Finally, NOx emissions are also included in the optimization obtaining the expected tradeoff between gross indicated efficiency and NOx. Under this optimization, cutting down the experimental emissions by 50% supposes a gross indicated efficiency penalty up to -8% m(f)H(v) when compared to the optimum combustion under nominal limits, while maintaining the experimental gross indicated efficiency allows to reduce the experimental emissions 30% at high load and 65% at low load and engine speed., This work was partially funded by GM Global R&D and the Government of Spain through Project TRA2017-89894-R. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational programme of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. Diego Blanco-Cavero is partially supported through contract FPI-S2-2016-1356 of the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politcenica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A study on diesel spray tip penetration and radial expansion under reacting conditions

  • Payri, Raul|||0000-0001-7428-5510
  • García-Oliver, José M|||0000-0002-2676-9681
  • Xuan, Tiemin
  • Bardi, Michele
The shape of Diesel spray was investigated at real engine conditions in a constant pressure combustion chamber. Schlieren imaging technique was used to make quantitative measurements of spray tip penetration and radial width stressing the impact that the fuel combustion and heat release have on the spray shape. The heat-release region and the Lift-off length were identified measuring OH* chem-iluminescence. The fuel (n-dodecane) as well as the operating conditions and the injector used (single axially-oriented hole, 89 mu m-diameter) were chosen following the guidelines of the Engine Combustion Network. The effects of different operating parameters on the axial and radial expansion were also investigated. According to the results the reacting spray can be divided into three parts: an inert part, a transient one, and a quasi-steady one that lays between the two other regions. A new method for evaluating this radial expansion of reacting spray was developed, which was evaluated under the different operating conditions. Results show that the radial expansion increases with increasing injection pressure and decreasing ambient temperature and ambient density. The oxygen concentration has no obvious effect on the radial expansion. (C) 2015 Elsevier Ltd. All rights reserved., Authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of simple surge-enhancing inlet geometries on the acoustic behaviour of a turbocompressor

  • Broatch, A.|||0000-0001-9991-1039
  • Margot , Xandra|||0000-0002-2639-0444
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Roig-Villanueva, Ferran
[EN] This paper reports the results of an experimental campaign where four different inlet geometries for the compressor of an automotive turbocharger were acoustically characterized. These four geometries (a straight pipe for reference, a tapered duct, a 90º elbow and a reservoir) were selected for their potential for deep surge margin enhancement, while being simple enough to be commonly found in production vehicles. A detailed measurement of this surge margin enhancement was performed, together with acoustic measurements of both radiated and orifice noise at design conditions of best isentropic efficiency and also close to the deep surge limit. Results demonstrated that while all the proposed geometries indeed enlarged the usable air mass flow range, changes in the acoustic behaviour of the system could be positive, neutral, or even negative. It is therefore important to carefully consider accurate noise measurements before implementing these geometric solutions in production vehicles, and to further pursue research on the link between the characteristic flow pattern produced by each inlet geometry and the noise emission of the turbocompressor., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The equipment used in this work has been partially supported by FEDER project funds ‘‘Dotacio´n de infraestructuras cientı´fico te´cnicas para el Centro Integral de Mejora Energe´tica y Medioambiental de Sistemas de Transporte (CiMeT)’’ (grant number FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Spanish Government.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of the injection conditions influence over n-dodecane and diesel sprays with two ECN single-hole nozzles. Part II: Reactive atmosphere

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Peraza, Jesús E
The second part of this experimental analysis, presented in this paper, seeks to go deep on the characterization of the Spray C and Spray D nozzles from the Engine Combustion Network, investigating the penetration of fuel spray at reacting conditions alongside characteristic parameters of combustion such as ignition delay and lift-off length. Both ECN mono-orifice injectors have similar nozzle flow capacity but different conicity degrees and corner sharpness, being Spray C more susceptible to cavitate. Schlieren imaging technique was employed to quantitatively measure reactive penetration and ignition delay, while lift-off length was identified through OH* chemiluminescence. As in the inert part of this research, n-dodecane and commercial diesel were selected for the tests, thereby the effect of the fuel properties in the measured parameters was analyzed. Also, once again the concept of R-parameter, defined as the penetration derivative respect to the square root of time was calculated to delve into the penetration behavior. The experiments were performed in a constant pressure-flow facility able to reproduce engine-like thermodynamic conditions. Results revealed that R-parameter evolution can be divided in four stages: an inert zone, a 'bump', a 'valley' part and a quasi-steady one that overlaps the previous inert part. Those stages are highly governed by ambient temperature and oxygen concentration. Nozzle geometry and fuel properties demonstrated to have a noteworthy influence on all measured parameters., This work was supported by "Ministerio de Economia y Cornpetitividad" of the Spanish Government in the frame of the projects "Estudio de la interaccion chorro-pared en condiciones realistas de motor", Ref. TRA2015-67679-c2-1-R. Moreover, the optical equipment employed in the project was purchased with investment from "Ministerio de Economia y Competitividad" FEDER-ICTS-2012-06.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A study on the internal convection in small turbochargers. Proposal of heat transfer convective coefficients

  • Serrano, J.R.|||0000-0003-0692-3917
  • Olmeda, P.|||0000-0002-3161-0165
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Reyes Belmonte, Miguel Ángel
  • Tartoussi, Hadi
Nowadays turbochargers play an important role in improving internal combustion engines (ICE) performance. Usually, engine manufacturers use computer codes to predict the behaviour of both engine and turbocharger, the later by means of measured look-up maps. Using look-up maps different problems arise, being one of the most important the difference in heat transfer between the current operating condition and the conditions at which maps were measured. These effects are very important at low to medium turbocharger speeds (typical condition of urban driving conditions) where heat transfer can even be higher than mechanical power. In this work, the different convective heat transfer phenomena inside these kind of machines have been measured and analysed. Besides, general correlations for these flows, based on dimensionless numbers, are fitted and validated in three different turbochargers. The applicability of the model is shown by comparison the main results obtained when the model is used and not, improving up to 20 C the predicted turbine outlet temperature. The main advantages of applying these correlations rely on predicting fluids outlet temperatures (compressor, turbine, oil and coolant). The former is needed to feed accurately ICE model, turbine outlet temperature is important for aftertreatment device modelling while oil and coolant temperatures are important in order to design optimum cooling systems., This work has been partially supported by the Spanish Ministerio de Economa y Competitividad through grant no. TRA2012-36954. The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of Regulated Pollutant Emissions and Aftertreatment Efficiency in a GTDi Engine Using Different SOI Strategies

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Luján, José M.|||0000-0001-6133-8943
  • Climent, H.|||0000-0002-2407-5651
  • Soto-Izquierdo, Lian
  • Campos-Navarro, Daniel
[EN] In order to improve performance and minimize pollutant emissions in gasoline turbocharged direct-injection (GTDi) engines, different injection strategies and technologies are being investigated. The inclusion of exhaust gas recirculation (EGR) and the variation of the start of injection (SOI) are some of these strategies that can influence the air-to-fuel (AF) mixture formation and consequently in the combustion process and pollutant emissions. This article presents a complete study of the engine performance, pollutant emissions and aftertreatment efficiency that produces the SOI variation with a fixed EGR rate in a 4-cylinder, turbocharged, gasoline direct-injection engine with 2.0 L displacement. The equipment used in this study are TSI-EEPS for particle measurement and HORIBA MEXA 1230-PM for soot measurement being HORIBA MEXA 7100-DEGR with a heated line selector the system employed for regulated gaseous emission measurement and aftertreatment evaluation. The experimental results confirm how the use of an adequate SOI strategy is indispensable to obtain low exhaust emissions values and a balance between the different pollutants. There was found a slight reduction in brake specific fuel consumption (BSFC) with the SOI advance. The experiments showed a decrease in CO, a non-sensible variation of THC and an increase in NOx emissions with SOI delay. Additionally, a significant increase in particle emissions was observed with early SOIs. Finally, with the SOI delay the aftertreatment performance revealed an increase in the oxidation of CO and a decrease in the reduction of NOx., The equipment used in this work has been partially supported by FEDER project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", framed in the operational program of singular scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Application of UV Visible Light Absorption and Scattering technique to low absorption fuels under diesel-like conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • López, J. Javier|||0000-0002-9486-2511
  • Micó, Carlos|||0000-0001-5787-6212
Light Absorption and Scattering technique (LAS) has been applied for the measurement of fuel vapour distribution in diesel-type sprays. This technique is usually limited to fuels with relatively high absorptivity, which are sometimes not commonly used as surrogate fuels. In the present paper, a comparison of fuels with very different absorptive properties has been made to determine the range of application of the methodology. A calibration procedure has been applied to n-decane (DEC), a binary blend of n-decane and n-hexadecane (50DEC) and three blends of n-heptane with a highly-absorpting fuel (HEPB1, HEPB2 and HEPB3). This methodology enables the in-situ quantification of absorption coefficients at high pressure and temperature by creating a uniform mixture inside the cylinder. Results have been later applied for the quantification of fuel vapour distribution in sprays for DEC, 50DEC and HEPB3. Results obtained with these range of fuels have enabled to establish the limit in terms of absorption coefficient needed to get consistent results with the technique., This work was partially funded by the Government of Spain through Project TRA2011-26359 and Grant BES-2012-059721. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement and application of a methodology to perform the Global Energy Balance in internal combustion engines. Part 1: Global Energy Balance tool development and calibration

  • López, J. Javier|||0000-0002-9486-2511
  • Payri, F.|||0000-0002-3314-4911
  • Martín, Jaime|||0000-0002-0496-3176
  • Carreño-Arango, Ricardo
[EN] The increasingly stringent internal combustion engines emissions regulations, has led to the extended use of after-treatment systems, giving progressively more importance to the engine efficiency optimization. In this framework, the combined modelling and experimental methodologies to perform and analyse the energy balance are key to evaluate the potential of different engine strategies aimed at the consumption optimization and the identification of the improvement paths. This work has been divided into two parts, dealing separately with the development and application of a Global Energy Balance tool. This article corresponds to the first part, which comprises the description of the models required to perform a detailed energy balance and the calibration methodologies followed to achieve accurate energy terms estimation. The models are calibrated based on experimental information, thus, a thermodynamic analysis aimed at defining comparable quantities between experimental and modelled terms is performed. The uncertainty analysis of the tool shows a deviation in the determination of the heat transfer to the coolant and the oil of about ±2%, and in terms of fuel energy about ±1%., This work was partially funded by the Government of Spain through Project TRA2013-41348-R. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fuel temperature influence on the performance of a last generation common-rail diesel ballistic injector. Part II: 1D model development, validation and analysis

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • De La Morena, Joaquín|||0000-0003-0208-508X
A one-dimensional model of a solenoid-driven common-rail diesel injector has been developed in order to study the influence of fuel temperature on the injection process. The model has been implemented after a thorough characterization of the injector, both from the dimensional and the hydraulic point of view. In this sense, experimental tools for the determination of the geometry of the injector lines and orifices have been described in the paper, together with the hydraulic setup introduced to characterize the flow behaviour through the calibrated orifices. An extensive validation of the model has been performed by comparing the modelled mass flow rate against the experimental results introduced in the first part of the paper, which were performed for different engine-like operating conditions involving a wide range of fuel temperatures, injection pressures and energizing times. In that first part of the study, an important influence of the fuel temperature was reported, especially in terms of the dynamic behaviour of the injector, due to its ballistic nature. The results from the model have allowed to explain and further extend the findings of the experimental study by analyzing key features of the injector dynamics, such as the pressure drop established in the control volume due to the control orifices performance or the forces due to viscous friction, also assessing their influence on the needle lift laws., This work was partly sponsored by "Ministerio de Economia y Competitividad" (Spain) in the frame of the project "Comprension de la influencia de combustibles no convencionales en el proceso de inyeccion y combustion tipo diesel", reference TRA2012-36932. The equipment used in this work has been partially supported by FEDER (Spain) project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)", in the frame of the operation program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. This support is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of the influence of exhaust gas recirculation on heat transfer in the firedeck of a direct injection diesel engine

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Salvador-Iborra, Josep
  • Warey, Alok
[EN] Emissions control is a key topic for internal combustion engine development. One of the most widespread technologies to reduce the formation of nitrogen oxides is the recirculation of exhaust gas to the engine intake. Besides, carbon dioxide emissions from internal combustion engines can be reduced by increasing engine efficiency. A relevant factor for engine efficiency is heat rejection. The interaction between heat transfer and exhaust gas recirculation is not fully understood. In this paper, an experimental study is presented which aims to shed light on the influence of high pressure exhaust gas recirculation on heat transfer. Three operating points were analyzed. Heat flux was calculated at several locations of the firedeck from temperature measurements. The results showed that the influence of exhaust gas recirculation on heat transfer was significant. Reductions of heat flux up to 18% were observed. The largest reduction was found in the area near the center of the firedeck. To contextualize the findings in the framework of emissions reduction, the trade-off between nitrogen oxides and carbon dioxide was assessed for all test points., The authors acknowledge General Motors Global R&D for supporting this research. The equipment used in this work was partially supported by FEDER project funds Dotación de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06) , framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. Josep Salvador-Iborra was partially supported through contract FPI-S2-2016-1357 of Programa de Apoyo para la Investigación y Desarrollo (PAID-01-16) of Universitat Politècnica de València.