Pasar al contenido principal

EVALUACION DEL EFECTO DE LA TRANSMISION DE CALOR EN LA CAMARA SOBRE LA EFICIENCIA DE MOTORES DIESEL DE PEQUEÑA CILINDRADA

TRA2013-41348-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of in-cylinder swirl on engine efficiency and heat rejection in a light-duty diesel engine

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Blanco-Cavero, Diego
  • Warey, A.
  • Domenech, V.
[EN] During the last years, the growing awareness about the impacts of climate change lead to an increase in the importance of the efficiency over other criteria in the design of internal combustion engines. In this framework, the heat transfer to the combustion chamber walls can be considered as one of the main sources of indicated efficiency diminution. Hence, the main objective of this research is to thoroughly assess the effect of the swirl ratio on the heat rejection to the chamber walls, and thus on the efficiency, of a fully instrumented four-cylinder direct-injection diesel engine with variable swirl ratio (covering the range from 1.4 to 3). The analysis, based on the engine global energy balance, includes a combination of theoretical and experimental tools such as thermal flow measurement and dedicated thermocouples in the cylinder head and liner. Considering the results, it is shown that an increase in swirl ratio leads to a heat transfer enhancement, along with important changes on the combustion development. As a result of the combination of these two effects, it is shown that intermediate swirl ratios can slightly improve engine efficiency at low load, while increasing swirl worsens the combustion process and efficiency at high load. However, convective heat transfer increases about 3% of the fuel energy in the chamber when swirl ratio increases from 1.4 to 3. The heat rejection characterization is completed with the analysis of the wall temperatures. Despite the observed trends, heat transfer does not seem to be the only key issue for explaining the indicated and brake efficiencies, thus the pumping work plays an important role due to the effect of reducing the intake section to generate the swirl motion., This work was supported by GM Global R&D and the Spanish Ministry of Economy and Competitiveness (TRA2013-41348-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thermal analysis of a light-duty CI engine operating with diesel-gasoline dual-fuel combustion mode

  • Martín, Jaime|||0000-0002-0496-3176
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • García Martínez, Antonio
  • Carreño-Arango, Ricardo
  • Heuser, Benedikt
  • Kremer, Florian
  • Pischinger, Stefan
Reactivity Controlled Compression Ignition (RCCI) is one of the most promising premixed combustion modes, aimed at reducing simultaneously engine emissions and fuel consumption. In this work, the global energy balance (GEB) of a single-cylinder engine operating with dual-fuel and RCCI modes is analysed. The methodology used allows determining the energy degradation from the energy release during the combustion to the final work output, thus evaluating the performance of such combustion mode. The weight of each GEB term is analysed using two references: the injected and the burned fuel energies, thus decoupling the combustion and thermal processes. The analysis is performed by evaluating the effect of some key parameters: low/high reactivity fuel ratio, injection timing and EGR rate. The results show that increasing the low reactivity fuel leads to a better shape of the heat release rate, with a reduction of heat transfer and exhaust losses, thus improving the thermal efficiency about 1% with respect to a conventional Diesel combustion. Injection timing swept shows that a suitable optimization leads to further thermal efficiency increase up to 4%, while EGR has a limited effect. It is also concluded that there is still room for further improvement by reducing incomplete combustion losses., The support of the Spanish Ministry of Economy and Competitiveness (TRA2013-41348-R) is greatly acknowledged. This work was performed in the frame of the Cluster of Excellence "Tailor-Made Fuels from Biomass", which is funded by the Excellence Initiative by the German federal and state governments. Thus, the authors would like to thank the Institute for Combustion Engines, RWTH Aachen University, for all the support to perform the research activities.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimal control as a method for diesel engine efficiency assessment including pressure and NOx constraints

  • Guardiola, Carlos|||0000-0002-3150-8566
  • Climent, H.|||0000-0002-2407-5651
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Reig, Alberto
[EN] The present paper studies the optimal heat release law in a Diesel engine to maximise the indicated efficiency subject to different constraints, namely: maximum cylinder pressure, maximum cylinder pressure derivative, and NOx emission restrictions. With this objective, a simple but also representative model of the combustion process has been implemented. The model consists of a OD energy balance model aimed to provide the pressure and temperature evolutions in the high pressure loop of the engine thermodynamic cycle from the gas conditions at the intake valve closing and the heat release law. The gas pressure and temperature evolutions allow to compute the engine efficiency and NOx emissions. The comparison between model and experimental results shows that despite the model simplicity, it is able to reproduce the engine efficiency and NOx emissions. After the model identification and validation, the optimal control problem is posed and solved by means of Dynamic Programming (DP). Also, if only pressure constraints are considered, the paper proposes a solution that reduces the computation cost of the DP strategy in two orders of magnitude for the case being analysed. The solution provides a target heat release law to define injection strategies but also a more realistic maximum efficiency boundary than the ideal thermodynamic cycles usually employed to estimate the maximum engine efficiency. (C) 2017 Elsevier Ltd. All rights reserved., Thanks are due to the Ministerio de Economia y Competitividad by its financial support through project mu-Balance (TRA2013-41348-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental analysis of the global energy balance in a DI diesel engine

  • Payri, F.|||0000-0002-3314-4911
  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Carreño, Ricardo
The increasingly stringent internal combustion engines (ICE) emissions regulations, has led to the extended use of after-treatment systems, giving progressively more importance to the engine efficiency optimization. In this context, the experimental methodologies to perform and analyse the energy balance show as a key issue to evaluate the potential of different engine strategies aimed at the consumption optimization and the improvement paths identification. This works deals with the complete description of an experimental energy balance tool, including the comprehensive description of the specific designed experimental installation used to the determination of each energy term involved in the energy balance. After the tool description, a study of the energy balance in the engine map of a DI Diesel engine was carried out, with the objective of determining the engine speed and load influence on each energy term. A subsequent parametric study varying the coolant temperature, the intake air temperature and the start of the injection (SOI) and their influence in the engine efficiency has been performed. The results shows that the variation of the coolant temperature has an almost negligible effect in terms of efficiency whilst cooling the air yields in an improvement about 1% and advancing the SOI about 1.5%., The support of the Spanish Ministry of Economy and Competitiveness (TRA2013-41348-R) is greatly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of swirl effect on the Global Energy Balance of a HSDI Diesel engine

  • Benajes, Jesús|||0000-0002-1653-9188
  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Blanco-Cavero, Diego
  • Warey, Alok
[EN] In the last years, a growing interest about increasing engine efficiency has led to the development of new engine technologies. Since air motion in the chamber is a key issue in internal combustion engines to improve the air-fuel mixing process and achieve faster burning rates, modern Diesel engines are designed to generate gas vorticity (swirl) that lead to enhanced turbulence in the combustion chamber. However, the use of swirl has a direct effect on fuel consumption due to the changes in the in-cylinder processes, affecting indicated efficiency, and also on the air management. An analysis, based on the engine Global Energy Balance (GEB), is presented to thoroughly assess the behavior of a high speed direct injection Diesel engine under variable swirl levels at different operating points. The tests have been performed keeping constant both the conditions at intake valve closing and combustion phasing, thus minimizing the variability due to in-cylinder conditions and the combustion process. The analysis includes a combination of theoretical (0D models) and experimental tools (heat rejection and wall temperature measurement) used to ensure control of in-cylinder conditions and to provide detailed explanation of the different phenomena affecting engine efficiency when swirl ratio is modified. Based on these tools, impact of swirl on the engine GEB is analyzed in detail paying special attention to engine efficiency and heat transfer in the chamber. Results show that increasing swirl has two main effects regarding the gross indicated efficiency (eta(i)): on one hand chamber heat rejection increases and therefore eta(i) diminishes about -0.5% at low load and 0.4% at high load; on the other hand combustion development is affected and thus a eta(i) improvement higher to 1.5% is achieved at low load and speed. The combination of these effects leads to a gross indicated efficiency increase higher to 1% at an optimum swirl ratio that diminishes when engine speed increases. In addition, pumping losses effect dominates brake efficiency behavior, which always diminishes (from 0.9% to 1.4%) when swirl increases. (C) 2017 Elsevier Ltd. All rights reserved., The support of GM Global R&D and the Spanish Ministry of Economy and Competitiveness (TRA2013-41348-R) is greatly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An adapted heat transfer model for engines with tumble motion

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Carreño, Ricardo
In the last years, a growing interest about increasing the engine efficiency has led to the development of new engine technologies. The accurate determination of the heat transfer across the combustion chamber walls is highly relevant to perform a valid thermal balance while evaluating the potential of new engine concepts. Several works dealing with heat transfer correlations that consider the swirl motion are found in the literature; however, there is a lack of works dealing with heat transfer correlations which take into account the effect of the tumble movement. In this work, a new heat transfer model accounting for the tumble motion is presented. A two stroke HSDI Diesel engine with high tumble and no swirl is used to perform the theoretical study, the model development and its final calibration. Initially, a theoretical analysis of the gas movement phenomena is carried out based on CFD results and then, a model is developed and calibrated based on a skip-fire testing technique. Finally, a sensitivity study focused on evaluating the model robustness is performed. The results confirm an average RMSE reduction of 70% with respect to the Woschni model, being this consistent improvement qualitatively evidenced in the instantaneous heat transfer evolution, The support of the Spanish Ministry of Economy and Competitiveness (TRA2013-41348-R) is greatly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement and application of a methodology to perform the Global Energy Balance in internal combustion engines. Part 1: Global Energy Balance tool development and calibration

  • López, J. Javier|||0000-0002-9486-2511
  • Payri, F.|||0000-0002-3314-4911
  • Martín, Jaime|||0000-0002-0496-3176
  • Carreño-Arango, Ricardo
[EN] The increasingly stringent internal combustion engines emissions regulations, has led to the extended use of after-treatment systems, giving progressively more importance to the engine efficiency optimization. In this framework, the combined modelling and experimental methodologies to perform and analyse the energy balance are key to evaluate the potential of different engine strategies aimed at the consumption optimization and the identification of the improvement paths. This work has been divided into two parts, dealing separately with the development and application of a Global Energy Balance tool. This article corresponds to the first part, which comprises the description of the models required to perform a detailed energy balance and the calibration methodologies followed to achieve accurate energy terms estimation. The models are calibrated based on experimental information, thus, a thermodynamic analysis aimed at defining comparable quantities between experimental and modelled terms is performed. The uncertainty analysis of the tool shows a deviation in the determination of the heat transfer to the coolant and the oil of about ±2%, and in terms of fuel energy about ±1%., This work was partially funded by the Government of Spain through Project TRA2013-41348-R. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Application of a zero-dimensional model to assess the effect of swirl on indicated efficiency

  • Broatch, A.|||0000-0001-9991-1039
  • Martín, Jaime|||0000-0002-0496-3176
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Blanco-Cavero, Diego
  • Warey, Alok
  • Domenech, Vicent
[EN] Increasing internal combustion engine efficiency continues being one of the main goals of engine research. To achieve this objective, different engine strategies are being developed continuously. However, the assessment of these techniques is not straightforward due to their influence on various intermediate phenomena inherent to the combustion process, which finally result in indicated efficiency trade-offs. During this work, a new methodology to assess these intermediate imperfections on gross indicated efficiency using a zero-dimensional model is developed. This methodology is applied to a swirl parametric study, where it has been concluded that the heat transfer and the rate of heat release are the single relevant changing phenomena. Results show that heat transfer always increases with swirl affecting negatively gross indicated efficiency (around -0.5%), while the impact of combustion velocity is not monotonous. It is enhanced up to a certain swirl ratio (it changes with engine speed) at low engine speed (resulting in an increment of +1.7% in gross indicated efficiency), but it is slowed down at high engine speed with the consequent worsening of gross indicated efficiency (-0.8%)., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partially funded by GM Global R&D and the Government of Spain through Project TRA2013-41348-R. D. B.-C. was partially supported through contract FPI-S2-2016-1356 of the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.