Pasar al contenido principal

REDUCCION DE LAS EMISIONES DE CO2 EN VEHICULOS PARA TRANSPORTE USANDO COMBUSTION DUAL NATURAL GAS-DIESEL

TRA2014-58870-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2014
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of Air Flow Interaction with Pilot Injections in a Diesel Engine by Means of PIV Measurements

  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Gil, A.|||0000-0001-7192-6992
  • Pachano-Prieto, Leonardo Manuel
[EN] With ever-demanding emission legislations in Compression Ignition (CI) engines, new premixed combustion strategies have been developed in recent years seeking both, emissions and performance improvements. Since it has been shown that in-cylinder air flow affects the combustion process, and hence the overall engine performance, the study of swirling structures and its interaction with fuel injection are of great interest. In this regard, possible Turbulent Kinetic Energy (TKE) distribution changes after fuel injection may be a key parameter for achieving performance improvements by reducing in-cylinder heat transfer. Consequently, this paper aims to gain an insight into spray-swirl interaction through the analysis of in-cylinder velocity fields measured by Particle Image Velocimetry (PIV) when PCCI conditions are proposed. Experiments are carried out in a single cylinder optical Diesel engine with bowl-in-piston geometry. A standard 2D PIV system is used for measuring instantaneous velocity fields in a cross section (swirl-plane) inside the combustion chamber. The test matrix is based on an advanced single pilot injection with energizing time and injection pressure sweeps at different crank-angles. Results show that swirl ratio decreases with the increase of injected fuel mass. The decrease in swirl ratio also comes with a homogenization of the flow field. This homogenization along with lower swirl ratios might decrease heat transfer to cylinder walls., The support of the Spanish Ministry of Economy and Competitiveness (TRA2014-58870-R,) is greatly acknowledged through HiReCo project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluating the emissions and performance of two dual-mode RCCI combustion strategies under the World Harmonized Vehicle Cycle (WHVC)

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Roso, Vinícius Rückert
  • Santos Martins, Mario Eduardo
[EN] This work compares the emissions and performance of two dual-mode reactivity controlled compression ignition (RCCI) combustion strategies under the World Harmonized Vehicle Cycle (WHVC), a chassis dynamometer version of the World Harmonized Transient Cycle (WHTC) test proposed by the EURO VI emission regulation for heavy-duty engines. The major difference between the two dual-mode combustion strategies investigated is that, while one of them relies on covering with conventional diesel combustion (CDC) the part of the map that cannot be covered by RCCI regime (RCCI/CDC dual-mode), the other does it relying on dual-fuel diffusion combustion (dual-mode dual-fuel). The influence of the gear shifting strategy on the emissions and performance over the WHVC is discussed first. Later, both dual-mode concepts are compared considering the optimal gear shifting strategy. The results suggest that dual-mode dual-fuel concept allows reducing the specific fuel consumption by 7% in average versus RCCI/CDC concept. Moreover, NOx emissions are around 87% lower with dual mode dual-fuel, meeting the EURO VI requirements without the need for an SCR aftertreatment system. In counterpart, HC and CO emissions are near 2 and 10 times greater, respectively, for dual-mode dual fuel than for RCCI/CDC. (C) 2017 Elsevier Ltd. All rights reserved., The experimental results used in this work come from an investigation funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R). The author J. Monsalve-Serrano acknowledges the financial support from the Universitat Politecnica de Valencia under the Grant "Ayudas Para la Contratacion de Doctores para el Acceso al Sistema Espafiol de Ciencia, Tecnologia e InnovaciOn". The author Vinicius Ruckert Roso would like to acknowledge the financial support from CAPES in providing the necessary bursary and to the Universidade Federal de Santa Maria and Universidade Federal de Minas Gerais-Brazil by the financial support in acquiring the software licenses needed for this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Redesign and characterization of a single-cylinder optical research engine to allow full optical access and fast cleaning during combustion studies

  • Benajes, Jesús|||0000-0002-1653-9188
  • Pastor, José V.|||0000-0003-4113-4681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
[EN] This work describes the update of an optical engine design with the aim of increasing its capabilities when used for combustion studies. The criteria followed to perform the optical engine redesign were: maximize the optical accessibility to the combustion chamber, minimize the time consumed to clean the optical parts, and minimize the adaptation costs. To meet these requirements, a modular design using window-holders to fit the windows in the optical flange, was proposed. This novel solution allows optical access near the cylinder-head plane while maintaining high operating flexibility (i.e. fast transition between optical and metal engine, and very fast cleaning procedure). The new engine design has three additional optical accesses to the combustion chamber and resulted in more efficient operation compared to the original design, reducing the time consumed to clean the optical parts from 40 down to 10 min. Two main parameters of the new engine were characterized, the effective compression ratio and the rotatory flow field velocity (swirl). The characterization process revealed very similar values between the effective and geometric compression ratios (14.7:1 vs 14.2:1), which confirms the use of appropriate dimensional tolerances during the machining process and low amount of blow-by. Finally, the swirl ratio was characterized through particle image velocimetry measurements for different crank timings at 1200 rpm and motored conditions, using the optical piston with a cylindrical bowl. This method revealed swirl ratios varying from 1 to 1.7 depending on the timing considered, with increasing trend as the piston moves towards the top dead center., This work has been partially funded by the Spanish Government under the project HiReCo TRA2014-58870-R. The equipment used has been partially funded by FEDER project ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. The author J. Monsalve-Serrano acknowledges the financial support from the Universitat Politecnica de Valencia under the grant "Ayudas Para la Contratacion de Doctores para el Acceso al Sistema Espanol de Ciencia, Tecnologia e Innovacion". The authors wish to thank Daniel Lerida for his technical work during the redesign process.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Exploring the limits of the reactivity controlled compression ignition combustion concept in a light-duty diesel engine and the influence of the direct-injected fuel properties

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
[EN] This experimental work investigates the operational limits of the reactivity controlled compression ignition combustion concept in a light-duty single-cylinder diesel engine using the stock compression ratio (17.1:1) with specific constraints. In addition, the effects of using different direct-injected fuels on engine-out emissions and performance are analyzed. First, an engine mapping was performed using diesel and gasoline as direct-injected and port-injected fuels, respectively. The operational limits of the reactivity controlled compression ignition concept have been found to be confined in the region defined from 2 to 5 bar indicated mean effective pressure at 1000 rev/min and from 4 to 8 bar indicated mean effective pressure at 3000 rev/min. In that portion of the map, nitrogen oxides and smoke emissions were below 0.4 g/kW h and 0.1 filter smoke number simultaneously, and the engine mechanical limits were respected. Later, the effects of the direct-injected fuel properties have been evaluated at the points that define the frontiers of maximum and minimum engine load in the baseline engine map (diesel/gasoline). To do this, three additional fuels based on diesel-gasoline mixings at different ratios (90%-10%, 70%-30% and 50%-50%), also known as dieseline, were used as direct-injected fuel instead of 100% diesel. To isolate the effects of each direct-injected fuel, the same engine settings were used for the comparison. The results show that, as the reactivity gradient between the high and low reactivity fuel diminishes, the sequential autoignition achieved in reactivity controlled compression ignition due to local combustion reactions switches to a more kinetically controlled homogeneous charge compression ignition-like combustion process. Finally, all the fuels were found to be capable of operating inside the emissions restrictions imposed by doing little modifications on the baseline calibration. However, no clear potential was found versus using 100% diesel as high-reactivity fuel., The authors gratefully acknowledge General Motors Global Research & Development for providing the engine used in this investigation. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through HiReCo project (TRA2014-58870-R). The author J. Monsalve-Serrano acknowledges the financial support from the Universitat Politecnica de Valencia under the grant "Ayudas Para la Contratacion de Doctores para el Acceso al Sistema Espanol de Ciencia, Tecnologia e Innovacion".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Benefits of E85 versus gasoline as low reactivity fuel for an automotive diesel engine operating in reactivity controlled compression ignition combustion mode

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
[EN] This work shows the capabilities of E85 fuel to be used as low reactivity fuel in a high compression ratio light-duty diesel engine (17.1:1) running under reactivity controlled compression ignition concept. To do this, experimental steady-state engine maps are obtained in a single-cylinder engine with diesel-E85 fuel combination. The engine mapping was performed following the same procedure used in previous works with other fuel combinations to allow the results comparison. Considering the mechanical and emissions limits imposed during the engine mapping, it was found that with diesel-E85 the combustion concept is limited to the region defined from 2 to 7 bar at 1000 rpm, and from 1.5 to 9 bar indicated mean effective pressure at 3000 rpm. This operating region was satisfied with nitrogen oxides, soot and pressure rise rate levels below 0.4 g/kWh, 0.01 g/kWh and 10 bar/CAD, respectively. The reactivity controlled compression ignition maps with diesel-E85 were obtained taking as reference the total fuel energy used in a previous work to map the engine with diesel-gasoline. The direct comparison of both combustion concepts (diesel-E85 and diesel-gasoline) revealed that E85 allows to extend the engine map around 2 bar indicated mean effective pressure towards the high load region. Moreover, the minimum load achieved at high engine speeds was decreased down to 1.5 indicated mean effective pressure. Finally, the differences in terms of emissions and performance between both reactivity controlled compression ignition concepts are highlighted by doing the difference between the maps of several variables., The authors gratefully acknowledge General Motors Global Research & Development for providing the engine used in this investigation. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through HiReCo project (TRA2014-58870-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of laser induced plasma ignition timing and location on Diesel spray combustion

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Pinotti, Mattia
[EN] An experimental study about the influence of the local conditions at the ignition location on combustion development of a direct injection spray is carried out in an optical engine. A laser induced plasma ignition system has been used to force the spray ignition, allowing comparison of combustion's evolution and stability with the case of conventional autoignition on the Diesel fuel in terms of ignition delay, rate of heat release, spray penetration and soot location evolution. The local equivalence ratio variation along the spray axis during the injection process was determined with a 1D spray model, previously calibrated and validated. Upper equivalence ratios limits for the ignition event of a direct injected Diesel spray, both in terms of ignition success possibilities and stability of the phenomena, could been determined thanks to application of the laser plasma ignition system. In all laser plasma induced ignition cases, heat release was found to be higher than for the autoignition reference cases, and it was found to be linked to a decrease of ignition delay, with the premixed peak in the rate of heat release curve progressively disappearing as the ignition delay time gets shorter. Ignition delay has been analyzed as a function of the laser position, too. It was found that ignition delay increases for plasma positions closer to the nozzle, indicating that the amount of energy introduced by the laser induced plasma is not the only parameter affecting combustion initiation, but local equivalence ratio plays a major role, too. (C) 2016 Elsevier Ltd. All rights reserved., The authors acknowledge that this research work has been partly funded by the Government of Spain under the project HiR-eCo TRA2014-58870-R and grant BES-2015-072119. The equipment used in this work has been partially supported by FEDER project ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of injection settings on gaseous emissions and particle size distribution in the dual-mode dual-fuel concept

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Macian Martinez, Vicente
  • Villalta-Lara, David
  • Soto, Lian
[EN] Reactivity controlled compression ignition concept has been highlighted among the low temperature combustion strategies. However, this combustion strategy presents some problems related to high levels of hydrocarbon and carbon monoxide emissions at low load and high-pressure rise rate at high load. Therefore, to diminish these limitations, the dual-mode dual-fuel concept has been presented as an excellent alternative. This concept uses two fuels of different reactivity and switches from a dual-fuel fully premixed strategy (based on the reactivity controlled compression ignition concept) during low load to a diffusive nature during high load operation. However, the success of dual-mode dual-fuel concept depends to a large extent on the low reactivity/high reactivity fuel ratio and the injection settings. In this study, parametric variations of injection pressure and injection timing were experimentally performed to analyze the effect over each combustion process that encompasses the dual-mode dual-fuel concept and its consequent impact on gaseous and particles emissions, including an analysis of particle size distribution. The experimental results confirm how the use of an adequate injection strategy is indispensable to obtain low exhaust emission and a balance between the different pollutants. In the fully premixed reactivity controlled compression ignition strategy, the particles concentrations were dominated by nucleation mode; however, the increase in injection pressure and the advance of the diesel main injection timing provided a simultaneous reduction of nitrogen oxide and solid particles (accumulation mode). During the highly premixed reactivity controlled compression ignition strategy, the accumulation-mode particles increased, and their concentrations were higher when the diesel main injection timing advanced and injection pressure decreased, as well as there was a slight increase in nitrogen oxide emissions. Finally, in the dual-fuel diffusion strategy, the concentrations of accumulation-mode particles were higher and there was a considerable increase of these particles with the advance of the diesel main injection timing and the reduction of the injection pressure, while the nitrogen oxide emissions decreased., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fuel consumption and engine-out emissions estimations of a light-duty engine running in dual-mode RCCI/CDC with different fuels and driving cycles

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] This work compares the performance and emissions of two dual-mode combustion concepts over different driving cycles by means of vehicle systems simulations. The dual-mode concept relies on switching between the dual-fuel concept known as reactivity controlled compression ignition (RCCI) and conventional diesel combustion (CDC) to cover the whole engine map. The experimental RCCI maps obtained with diesel-E85 and diesel-gasoline used as inputs to perform the simulations were obtained in a high compression ratio light-duty diesel engine (17.1:1) following the same mapping procedure in both cases. The driving cycles simulated to perform the comparison were the Real Driving Emissions cycle (Europe), Worldwide harmonized Light vehicles Test Cycle (Europe), Federal Test Procedure FTP-75 (United States) and JC08 (Japan). The results show that the dual-mode concept has potential to be implemented in flexible-fuel vehicles. Using gasoline as low reactivity fuel (LRF) for RCCI, the vehicle mileage would be equal to CDC, but having reductions in NOx and soot emissions of 16% and 50%, respectively, along the RDE cycle. Using E85 instead of gasoline, the reductions in NOx and soot emissions increase up to 50% and 85%, respectively, but in this case promoting higher thermal efficiency than CDC. (C) 2018 Elsevier Ltd. All rights reserved., The authors gratefully acknowledge General Motors Global Research & Development for providing the engine used to acquire the experimental data shown in this investigation. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through HiReCo project (TRA2014-58870-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Particulates Size Distribution of Reactivity Controlled Compression Ignition (RCCI) on a Medium-Duty Engine Fueled with Diesel and Gasoline at Different Engine Speeds

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Boronat-Colomer, Vicente
[EN] This work investigates the particulates size distribution of reactivity controlled compression ignition combustion, a dual-fuel concept which combines the port fuel injection of low-reactive/gasoline-like fuels with direct injection of highly reactive/diesel-like fuels. The particulates size distributions from 5-250 nm were measured using a scanning mobility particle sizer at six engine speeds, from 950 to 2200 rpm, and 25% engine load. The same procedure was followed for conventional diesel combustion. The study was performed in a single-cylinder engine derived from a stock medium-duty multi-cylinder diesel engine of 15.3:1 compression ratio. The combustion strategy proposed during the tests campaign was limited to accomplish both mechanical and emissions constraints. The results confirms that reactivity controlled compression ignition promotes ultra-low levels of nitrogen oxides and smoke emissions in the points tested. However, in spite of having similar or lower smoke emissions, the number of particles in some conditions is higher for the reactivity controlled compression ignition than for conventional diesel combustion. Nucleation mode dominates the particle formation for the reactivity controlled compression ignition mode, while accumulation mode dominates the particle formation for conventional diesel combustion. Thus, it is confirmed that the smoke measurement in filter smoke number units cannot be used to correlate the total particle mass for the reactivity controlled compression ignition mode, as typically done for conventional diesel combustion., This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R). The predoctoral contract of the author V. Boronat (FPI-S2-2017-2882) is granted by the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of the Universitat Politecnica de Valencia. The author J. Monsalve-Serrano acknowledges the financial support from the Universitat Politecnica de Valencia under the grant "Ayudas Para la Contratacion de Doctores para el Acceso al Sistema Espanol de Ciencia, Tecnologia e Innovacion".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dual-Fuel Combustion for Future Clean and Efficient Compression Ignition Engines

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Boronat-Colomer, Vicente
[EN] Stringent emissions limits introduced for internal combustion engines impose a major challenge for the research community. The technological solution adopted by the manufactures of diesel engines to meet the NOx and particle matter values imposed in the EURO VI regulation relies on using selective catalytic reduction and particulate filter systems, which increases the complexity and cost of the engine. Alternatively, several new combustion modes aimed at avoiding the formation of these two pollutants by promoting low temperature combustion reactions, are the focus of study nowadays. Among these new concepts, the dual-fuel combustion mode known as reactivity controlled compression ignition (RCCI) seems more promising because it allows better control of the combustion process by means of modulating the fuel reactivity depending on the engine operating conditions. The present experimental work explores the potential of different strategies for reducing the energy losses with RCCI in a single-cylinder research engine, with the final goal of providing the guidelines to define an efficient dual-fuel combustion system. The results demonstrate that the engine settings combination, piston geometry modification, and fuel properties variation are good methods to increase the RCCI efficiency while maintaining ultra-low NOx and soot emissions for a wide range of operating conditions., The authors acknowledge VOLVO Group Trucks Technology for supporting this research and express their gratitude to the Spanish economy and competitiveness ministry for partially funding this investigation under the project HiReCo (TRA2014-58870-R). The author J. Monsalve-Serrano thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-S2-2015-1531), which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

An investigation on the particulate number and size distributions over the whole engine map from an optimized combustion strategy combining RCCI and dual-fuel diesel-gasoline

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Boronat-Colomer, Vicente
[EN] Literature demonstrates that, for premixed low temperature combustion concepts, particulate matter cannot be directly extrapolated from soot emissions measurements, as typically done for conventional diesel combustion. This is because the particulate matter from low temperature combustion has low fraction of carbonaceous compounds and great amount of soluble organic fraction, which is not captured by the smoke measurement techniques such as the optical reflectometry. By this reason, the study of the particulate matter characteristics from this combustion techniques requires using specific equipment. The aim of the current work is to gain understanding on the particulate matter characteristics from the dual-mode dual-fuel combustion, which is an optimized combustion strategy that combines fully and highly premixed RCCI regimes at low and medium loads, and switches to dual-fuel diffusion combustion at full load. The study was performed over the whole engine map, using a 15.3:1 compression ratio medium-duty EURO VI diesel engine. In particular, the particulate number and size distributions were sampled using a scanning mobility particle sizer and a condensation particle counter, which allow measuring the size distribution and total number of particles from 5 to 250 nm. Results demonstrate that the fully premixed RCCI combustion is dominated by small particles (less than 30 nm in mobility diameter), the dual-fuel diffusion mode is dominated by larger particles (around 100 nm in mobility diameter) showing more diesel-like particle size distributions, and the highly premixed reactivity controlled compression ignition regime shows a transitional particle size distribution with two peaks of mobility diameters around 20 and 80 nm. (C) 2017 Elsevier Ltd. All rights reserved., This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R). The predoctoral contract of the author V. Boronat (FPI-S2-2017-2882) is granted by the Programa de Apoyo para la Investigación y Desarrollo (PAID) of the Universitat Politècnica de València. The author J. Monsalve-Serrano acknowledges the financial support from the Universitat Politècnica de València under the Grant Ayudas Para la Contratación de Doctores para el Acceso al Sistema Español de Ciencia, Tecnología e Innovación .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Laser induced plasma methodology for ignition control in direct injection sprays

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio
  • Pinotti, Mattia
New combustion modes for internal combustion engines represent one of the main fields of investigation for emissions control in transportation Industry. However, the implementation of lean fuel mixture condition and low temperature combustion in real engines is limited by different unsolved practical issues. To achieve an appropriate combustion phasing and cycle-to-cycle control of the process, the laser plasma ignition system arises as a valid alternative to the traditional electrical spark ignition system. This paper proposes a methodology to set-up and optimize a laser induced plasma ignition system that allows ensuring reliability through the quantification of the system effectiveness in the plasma generation and positional stability, in order to reach optimal ignition performance. For this purpose, experimental tests have been carried out in an optical test rig. At first the system has been optimized in an atmospheric environment, based on the statistical analysis of the plasma records taken with a high speed camera to evaluate the induction effectiveness and consequently regulate and control the system settings. The same optimization method has then been applied under engine-like conditions, analyzing the effect of thermodynamic ambient conditions on the plasma induction success and repeatability, which have shown to depend mainly on ambient density. Once optimized for selected engine conditions, the laser plasma induction system has been used to ignite a direct injection Diesel spray, and to compare the evolution of combustion with that of a conventional auto-ignited Diesel spray., The authors acknowledge that this research work has been partly funded by the Government of Spain under the project HiReCo TRA2014-58870-R and grant BES-2015-072119. The equipment used in this work has been partially supported by FEDER project ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

In-cylinder soot radiation heat transfer in direct-injection diesel engines

  • Benajes, Jesús|||0000-0002-1653-9188
  • Martín, Jaime|||0000-0002-0496-3176
  • García Martínez, Antonio
  • Villalta Lara, David
  • Warey, Alok
The efficiency and CO2 are one of the main concerns of automotive manufacturers. There are several strategies under investigation to solve this problem. In the present work, the research effort has been focused on improving knowledge of in-cylinder heat transfer and its impact on engine efficiency. In particular, soot radiation was studied since it can be considered a significant source of the efficiency losses in modern diesel engines. Considering previous studies, the portion of total chemical energy released during combustion lost due to radiation heat transfer varies widely from 0.5% up to 10%, depending on engine parameters and combustion process. Thus, the main objective of this work was to evaluate the amount of energy lost to soot radiation relative to the input fuel chemical energy during the combustion event under different operating conditions in a completely controlled environment provided by an optical engine. Under these simplified conditions, two-color method was applied by using high speed imaging pyrometer with cameras (two dimensional results) and optoelectronic pyrometer (zero dimensional results). Once a detailed comparison between both diagnostics was performed, optoelectronic pyrometer was used to characterize radiant energy losses in a fully instrumented 4-cylinder direct-injection lightduty diesel engine. In particular swirl ratio, 'EGR and combustion phasing effects on radiation heat transfer were evaluated., The authors acknowledge General Motors Global R&D for supporting this research and to express their gratitude to Spanish economy and competitiveness ministry for partially funding this research under the project HiReCo TRA2014-58870-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Gaseous emissions and particle size distribution of dual-mode dual-fuel diesel-gasoline concept from low to full load

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Boronat-Colomer, Vicente
[EN] Low temperature combustion concepts are in focus of study nowadays as a method to avoid the NOx-soot trade-off existing with conventional diesel combustion. One of the most promising strategy is known as reactivity controlled compression ignition because of its high thermal efficiency and the ultra-low nitrogen oxides and soot emissions. However, this concept presents several challenges such as the high levels of carbon monoxide and unburned hydrocarbons promoted at low load and unacceptable levels of pressure rise rate at high load. Therefore, to mitigate these shortcomings the dual-mode dual-fuel concept, combining reactivity controlled compression ignition and diffusive dual-fuel diesel-gasoline combustion, has been developed. Total number of particles is also limited by the emission standards. Previous studies focused in particles emissions carried out by the research community present particle size distribution, composition and mass of the particles on reactivity controlled compression ignition combustion mode. Additional studies were carried out in order to identify the components of these particles, being partially formed of volatiles, and reflects that particles are smaller than at conventional diesel combustion, presenting higher number of particles from nucleation mode than from accumulation mode. Dual-Mode Dual-Fuel concept may present a different behavior for particle distribution with respect to the conventional diesel combustion or the traditional low temperature concepts due to the nature of the particles. The objective of the present study is to measure the particle size distribution as well as gaseous emissions of this new Dual-Mode Dual-Fuel concept from low load to full load for a representative engine speed of 1200 rpm. Main results of this study suggest that Dual-Mode Dual-Fuel concept promotes higher quantity of particles than conventional diesel combustion despite of providing less smoke. In addition, nucleation mode particles dominate the particle size distribution for the new combustion concept at low load and moves towards accumulation mode domination at full load. (C) 2017 Elsevier Ltd. All rights reserved., This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R). The predoctoral contract of the author V. Boronat (FPI-S2-2017-2882) is granted by the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of the Universitat Politecnica de Valencia. The author J. Monsalve-Serrano acknowledges the financial support from the Universitat Politecnica de Valencia under the grant "Ayudas Para la Contratacion de Doctores para el Acceso al Sistema Espahol de Ciencia, Tecnologia e Innovacion".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The potential of RCCI concept to meet EURO VI NOx limitation and ultra-low soot emissions in a heavy-duty engine over the whole engine map

  • Benajes, Jesús|||0000-0002-1653-9188
  • Pastor, José V.|||0000-0003-4113-4681
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • García Martínez, Antonio
This work investigates the potential of RCCI concept to achieve ultra-low NOx and soot emissions over a wide range of engine speed and loads. For this purpose, a detailed experimental methodology has been defined and applied in a heavy-duty single-cylinder engine fueled with diesel and gasoline. In addition, to assess the influence of the engine compression ratio on RCCI capabilities two different compression ratios, 14.4:1 and 11:1, have been tested. Results suggest that a low compression ratio allows to fulfill all the self-imposed constraints (maximum cylinder pressure rise rate of 25 bar/CAD, NOx < 0.4 g/kW h and soot* < 0.01 g/kW h) from idle to full load and engine speeds from 900 to 1800 rpm. However, the use of higher compression ratio requires a delayed injection strategy to avoid excessive knocking levels, which results in unacceptable soot emissions at loads higher than 50%, even when gasoline fractions around 90% are used., The authors would like to acknowledge VOLVO Group Trucks Technology for supporting this research and to express their gratitude to Spanish economy and competitiveness ministry for partially funding this research under the project HiReCo TRA2014-58870-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Miller cycle for improved efficiency, load range and emissions in a heavy-duty engine running under reactivity controlled compression ignition combustion

  • Molina, Santiago|||0000-0001-7879-2421
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Estepa-Ruiz, Daniel
[EN] The low temperature, premixed combustion strategies are being investigated in the recent years as a mean to break the NOx-soot trade-off appearing during the diffusive conventional diesel combustion. This approach relies on promoting premixed combustion events with shortened duration, which reduces the heat transfer losses, improves the thermal efficiency, and allows a simultaneous reduction of engine-out NOx and soot emissions. However, since the combustion onset only depends on chemical kinetics, most of these strategies cannot be implemented at medium and high loads due to excessive pressure gradients, which lead to unacceptable noise levels and reliability issues. This experimental work investigates the potential of the Miller cycle as a strategy to minimize the aforementioned challenges when operating under reactivity controlled compression ignition combustion. Moreover, the coupled effect of the Miller cycle with the fuel reactivity modulation is also explored as a way for improving the combustion control. For this purpose, parametric studies varying the effective compression ratio and gasoline fraction have been done in a single-cylinder heavy-duty engine operating at 14 bar indicated mean effective pressure and 1200 rev/min as a baseline condition. The results show that this strategy allows better control of the in-cylinder thermodynamic conditions, enabling a simultaneous reduction of nitrogen oxides and soot emissions down to the EURO VI limits, while keeping a reduced fuel consumption and suitable in-cylinder maximum pressure gradients., The authors thanks VOLVO Group Trucks Technology for supporting this research. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R). Daniel Estepa is partially supported through contract FPI-S2-2015-1091 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Achieving clean and efficient engine operation up to full load by combining optimized RCCI and dual-fuel diesel-gasoline combustion strategies

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Boronat-Colomer, Vicente
[EN] This experimental work investigates the capabilities of the reactivity controlled compression ignition combustion concept to be operated in the whole engine map and discusses its benefits when compared to conventional diesel combustion. The experiments were conducted using a single-cylinder medium duty diesel engine fueled with regular gasoline and diesel fuels. The main modification on the stock engine architecture was the addition of a port fuel injector in the intake manifold. In addition, with the aim of extending the reactivity controlled compression ignition operating range towards higher loads, the piston bowl volume was increased to reduce the compression ratio of the engine from 17.5:1 (stock) down to 15.3:1. To allow the dual-fuel operation over the whole engine map without exceeding the mechanical limitations of the engine, an optimized dual-fuel combustion strategy is proposed in this research. The combustion strategy changes as the engine load increases, starting from a fully premixed reactivity controlled compression ignition combustion up to around 8 bar IMEP, then switching to a highly premixed reactivity controlled compression ignition combustion up to 15 bar IMEP, and finally moving to a mainly diffusive dual-fuel combustion to reach the full load operation. The engine mapping results obtained using this combustion strategy show that reactivity controlled compression ignition combustion allows fulfilling the EURO VI NOx limit up to 14 bar IMEP. Ultra-low soot emissions are also achieved when the fully premixed combustion is promoted, however, the soot levels rise notably as the combustion strategy moves to a less premixed pattern. Finally, the direct comparison of reactivity controlled compression ignition versus conventional diesel combustion using the nominal engine settings, reveals that reactivity controlled compression ignition can be a potential solution to reduce the selective catalyst reduction and diesel particulate filter aftertreatment necessities with a simultaneous improving of the thermal efficiency. (C) 2017 Elsevier Ltd. All rights reserved., This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R). The predoctoral contract of the author J. Monsalve-Serrano (FPI-S2-2015-1531) is granted by the Programa de Apoyo para la Investigación y Desarrollo (PAID) of the Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Combination of Swirl Ratio and Injection Strategy to Increase Engine Efficiency

  • Olmeda, P.|||0000-0002-3161-0165
  • Martín, Jaime|||0000-0002-0496-3176
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Villalta-Lara, David
  • Warey, Alok
  • Domenech Llopis, Vicente
[EN] Growing awareness about CO2 emissions and their environmental implications are leading to an increase in the importance of thermal efficiency as criteria to design internal combustion engines (ICE). Heat transfer to the combustion chamber walls contributes to a decrease in the indicated efficiency. A strategy explored in this study to mitigate this efficiency loss is to promote low swirl conditions in the combustion chamber by using low swirl ratios. A decrease in swirl ratio leads to a reduction in heat transfer, but unfortunately, it can also lead to worsening of combustion development and a decrease in the gross indicated efficiency. Moreover, pumping work plays also an important role due to the effect of reduced intake restriction to generate the swirl motion. Current research evaluates the effect of a dedicated injection strategy to enhance combustion process when low swirl is used. For this purpose, a combination of theoretical (0D and 1D models) and experimental tools were used. In particular, experiments were conducted in a single-cylinder direct-injection light-duty diesel engine. The analysis also included theoretical calculations to estimate pumping losses. Results show that an increase in swirl ratio leads to an increase in the gross indicated efficiency (balancing heat transfer losses and combustion improvement) but the higher pumping losses negate this positive benefit. In the lowest swirl ratio case, a suitable injection strategy based on multiple injections, together with an increase in the injection pressure, can provide similar gross indicated efficiency as high swirl ratio case while avoiding high pumping losses., The support of GM Global R&D and the Spanish Ministry of Economy and Competitiveness (TRA2014-58870-R,) is greatly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of low-pressure EGR on gaseous emissions and particle size distribution from a dual-mode dual-fuel (DMDF) concept in a medium-duty engine

  • Macian Martinez, Vicente
  • Villalta-Lara, David
  • Soto-Izquierdo, Lian
  • Bermúdez, Vicente|||0000-0002-2781-5598
[EN] The application of a low-temperature combustion concept, such as RCCI combustion under real engine operating conditions is extremely complex. However, the implementation of the dual-mode dual-fuel (DMDF) strategy allows operating in low-medium load with the RCCI combustion and in high load with dual-fuel diffusive combustion. This allows taking advantage of the benefits of RCCI combustion as the simultaneous reduction of PM and NOx emissions. However, there are still serious challenges that required to solve, such as the high-pressure rise rate and the excessive CO and HC emissions. In this sense, this work shows how the implementation and an adequate adjustment of the cooled LP-EGR rate significantly minimize these problems and also shows how the LP-EGR has a greater impact on the DMDF than on the CDC concept. This work has been performed in a modern medium-duty diesel engine fueled with standard gasoline and diesel fuels, with which a cooled LP-EGR loop has been coupled. A TSI Scanning Particle Sizer (SMPS 3936L75) was used to measure the particles size distribution and the Horiba MEXA-ONE-D1-EGR gas analyzer system to determine gaseous emissions. A parametric variation of the LP-EGR rate was experimentally performed to analyze the effect over each combustion process that encompasses the DMDF concept (fully premixed RCCI, highly premixed RCCI and dual-fuel diffusion) and its consequent impact on gaseous and particle emissions. In addition, results were compared against the CDC concept to state the benefits of the DMDF concept. Among the different results obtained, it can be highlighted that during the RCCI strategy the increase in LP-EGR rate provided a reduction in NOx emissions. Nonetheless, unlike that fully premixed RCCI in highly premixed RCCI combustion, the PM emissions increased with this increment in the LP-EGR rate, shifting the size distribution of particle toward larger sizes, but decreasing the HC and CO emissions. Finally, with the exception of the high HC and CO emissions in fully premixed RCCI, in all the combustion strategies of the DMDF concept, a reduction of the analyzed pollutants was observed when compared with the CDC mode., This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment on the consequences of injection strategies on combustion process and particle size distributions in Euro VI medium-duty diesel engine

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Villalta-Lara, David
  • Soto, Lian
[EN] Although there are already several works where the influence of injection parameters on exhaust emissions, and specifically on particulate matter emissions, in diesel engines has been evaluated, the diversity in the results that can be found in the literature indicates the need to carry out new experiments that can provide more information about the influence of these parameters on modern diesel engines. This study intends to be placed within this scientific framework, hence a parametric study was carried out based on the independent modification of the main injection timing and the injection pressure with respect to the nominal conditions of a new Euro VI direct injection diesel engine. Four steady-state operation points of the engine map were chosen: 25% load and 950 r/min, 50% load and 1500 r/min, 75% load and 2000 r/min and 100% load and 2200 r/min, where in each of these operation points, the variations of the injection parameters in the study on the combustion process and its consequent impact on the particle size distribution, including an analysis of the geometric mean diameter values, were evaluated. The results showed that the different injection strategies adopted, despite not significantly affecting the engine efficiency, did cause a significant impact on particle number emissions. At the low load operation, the size distribution showed a bimodal structure, and as the main injection timing was delayed and the injection pressure was decreased, the nucleation-mode particle concentration decreased, while the accumulation-mode particle concentration increased. In addition, at medium load, the nucleation-mode particle emission decreased considerably while the accumulation-mode particle emission increased, and this increase was much greater with the main injection timing delay and the injection pressure reduction. Similar behavior was observed at high load, but with a much more prominent pattern., The author(s) disclosed receipt of the following financial support for the research, authorship and/or publication of this article: This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R).