Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Corrosion resistance of ultra-high performance fibre- reinforced concrete

  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Ramón Zamora, José Enrique
  • Soto Camino, Juan
[EN] The corrosion resistance of ultra-high performance concrete (UH) made with different fibre contents and under distinct curing conditions was studied. No signs of carbonation were observed after 1 year of accelerated carbonation testing (3% CO2). The fibreless UHs¿ electrical resistivity was above 5000 ¿·m, although these values were 2-fold higher than a UH with 1% fibres and approximately 5-fold higher than a UH with 2% fibres. Concrete resistance to chloride penetration was also extremely high (the diffusion coefficient equalled 1.3·10¿13 m2/s) and curing temperatures of 60 °C or 90 °C improved even more these properties, while lack of curing made them slightly worse. Given these excellent properties, the corrosion rate in specimens submerged in chloride solution for 1 year was negligible (iCORR from 0.007 to 0.025 µA/cm2). These values remained stable with time, unlike the 50 MPa concrete at 2 months when iCORR starting to increase and was 12-fold higher after 1 year. The time estimated for corrosion onset in UH is on average about 150-fold higher than that of 50 MPa., Authors thank to the Spanish Government the financial support of project BIA2016-78460-C3-3-R and to the European Union¿s Horizon 2020 the financial support of ReSHEALience project (Grant Agreement No. 760824). Furthermore, authors would like to express their gratitude for the support of the Universitat Politecnica de Valencia. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The predoctoral scholarship granted to Josep Ramon Lliso Ferrando within the program "Formacion de Personal Investigador" from the Universitat Politecnica de Valencia (FPI-UPV-2018) is also gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multi-performance experimental assessment of autogenous and crystalline admixture-stimulated self-healing in UHPFRCCs: Validation and reliability analysis through an inter-laboratory study

  • Lo Monte, Francesco
  • Repesa, Lamija
  • Snoeck, Didier
  • Doostkami, Hesam
  • Roig-Flores, Marta
  • Jackson, Sam J.P.
  • Blanco Alvarez, Ana
  • Nasner, Milena
  • Borg, Ruben Paul
  • Schroefl, Christof
  • Giménez, Mercedes
  • Alonso, Maria Cruz
  • Serna, Pedro
  • De Belie, Nele
  • Ferrara, Liberato
[EN] The huge benefits brought by the use of Ultra High-Performance Fibre-Reinforced Cementitious Composites (UHPFRCCs) include their high "intrinsic" durability, which is guaranteed by (1) the compact microstructure and (2) the positive interaction between stable multiple-cracking response and autogenous self-healing capability. Hence, self-healing capability must be properly characterized addressing different performances, thus providing all the tools for completely exploiting such large potential. Within this context, the need is clear for a wellestablished protocol for self-healing characterization. To this end, in the framework of the Cost Action CA15202 SARCOS, six Round Robin Tests involving 30 partners all around Europe were launched addressing different materials, spanning from ordinary concrete to UHPFRCC, and employing different self-healing technologies. In this paper, the tailored experimental methodology is presented and discussed for the specific case of autogenous and crystalline-admixture stimulated healing of UHPFRCC, starting from the comparison of the results from seven different laboratories. The methodology is based on chloride penetration and water permeability tests in cracked disks together with flexural tests on small beams. The latter ones are specifically aimed at assessing the flexural performance recovery of UHPFRCCs, which stands as their signature design "parameter" according to the most recent internationally recognized design approaches. This multi-fold test approach allows to address both inherent durability properties, such as through-crack chloride penetration and apparent water permeability, and more structural/mechanical aspects, such as flexural strength and stiffness., The round robin activity reported in this paper has been performed in the framework of the COST Action CA 15202 "SARCOS" (Self-healing As prevention Repair of COncrete Structures, http:// www.sarcos.enq. cam.ac.uk) . The production of the material and the inter-laboratory comparison were also supported by the ReSHEALience project (Rethinking coastal defence and Green-energy Service infrastructures through enHancEd-durAbiLity high-performance cement-based materials) which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 760824 ( www.uhdc.eu).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of cracking on oxygen transport in UHPFRC using stainless steel sensors

  • Martínez-Ibernón, Ana|||0000-0003-2136-5650
  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
  • Serna Ros, Pedro|||0000-0001-8754-1165
  • Roig-Flores, Marta
  • Mezquida-Alcaraz, Eduardo J.
[EN] Reinforced concrete elements frequently suffer small cracks that are not relevant from the mechanical point of view, but they can be an entrance point for aggressive agents, such as oxygen, which could initiate the degradation processes. Fiber-Reinforced Concrete and especially Ultra High Performance Concrete increase the multi-cracking behavior, reducing the crack width and spacing. In this work, the oxygen availability of three types of concrete was compared at similar strain levels to evaluate the benefit of multi-cracking in the transport of oxygen. The types of concrete studied include traditional, High-Performance, and Ultra-High-Performance Fiber-Reinforced Concrete with and without nanofibers. To this purpose, reinforced concrete beams sized 150 x 100 x 750 mm(3) were prepared with embedded stainless steel sensors that were located at three heights, which have also been validated through this work. These beams were pre-cracked in bending up to fixed strain levels. The results indicate that the sensors used were able to detect oxygen availability due to the presence of cracks and the detected differences between the studied concretes. Ultra High Performance Concrete in the cracked state displayed lower oxygen availability than the uncracked High Performance Concrete, demonstrating its potential higher durability, even when working in cracked state, thanks to the increased multi-cracking response., The authors would like to express their gratitude to the Spanish Ministry of Science and Innovation for the pre-doctoral scholarship granted to Ana Martinez Ibernon (FPU 16/00723), to the Universitat Politecnica de Valencia for the pre-doctoral scholarship granted to Josep Ramon Lliso Ferrando (FPI-UPV-2018), and the European Union's Horizon 2020 ReSHEALience project (Grant Agreement No. 760824).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential step voltammetry: An approach to corrosion rate measurement of reinforcements in concrete

  • Ramón, J.E.
  • Bataller Prats, Román
  • Soto Camino, Juan
  • Gandía-Romero, Jose M.|||0000-0003-0257-3286
  • Alcañiz Fillol, Miguel|||0000-0002-4579-9210
  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
[EN] This paper presents a Potentiostatic Step Voltammetry approach to corrosion rate measurement of reinforcements in concrete. We have termed this approach PSV-TE since it is based on the Tafel extrapolation method, but with the added advantage that long and slow potentiodynamic scans are no longer required to obtain the Tafel slopes. In this way, the irreversible polarization of rebars is prevented, so PSV-TE is considered to be a non-destructive method. The Tafel slopes are obtained by fitting the current-time response of the system to a theoretical model which we have outlined and validated previously. In this way, the concrete's electrical resistance and double layer capacity are also obtained. In this study, the optimal PSV-TE design has been established and validated on a range of reinforced concrete specimens. Results show minimal deviation between PSV-TE and reference methods. Therefore, PSV-TE is part of the corrosion monitoring system we have patented., This work was supported by a pre-doctoral scholarship granted to Jose Enrique Ramon Zamora by the Spanish Ministry of Science and Innovation [grant number FPU13/00911]. We would also like to acknowledge financial support from the Spanish Ministry of Economy and Competitiveness through the national program of oriented research, development and innovation to societal challenges [project number BIA2016-78460-C3-3-R]. The research activity reported in this paper has been performed in the framework of the ReSHEALience project which has received funding from the European Union's Horizon 2020 research and innovation program [number 760824]. We extend our appreciation to Rafa Calabuig and Jesus Martinez, Material Laboratory technicians of the ETSIE of the Universitat Politecnica de Valencia, for their invaluable cooperation in the experimental work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Preliminary study on the fresh and mechanical properties of UHPC made with recycled UHPC aggregates

  • Roig-Flores, Marta
  • Borg, Ruben Paul
  • Ruiz-Muñoz, Cecilia
  • Mezquida-Alcaraz, Eduardo J.
  • Lozano Násner, Albany Milena
  • Gimenez-Carbo, Ester|||0000-0002-2856-4081
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] The recycling of construction and demolition waste material reduces disposal of material and also the consumption of resources, therefore promoting sustainability in construction. Ultra-high performance concrete (UHPC) is a relatively new material and its feasibility to be recycled needs to be verified. This work investigates the recyclability of UHPC disposed elements, including the production of recycled aggregates and fibres from UHPC. The feasibility of recycled aggregates and fibres at different replacement rates was evaluated through the assessment of rheological and mechanical properties of the newly produced UHPC elements. Concrete mixes with replacement of aggregates at 50% and 100%, displayed compression strength comparable to original UHPC, maintaining the original deflection-hardening response. However, their workability was slightly reduced when increasing the content of the recycled material. Mixes with recycled fibres experienced residual strength losses and behaved as deflection-softening materials in the case of complete replacement., The activity described in this paper has been performed in the framework of the project 'Rethinking coastal defence and Green-energy Service infrastructures through enHancEd-durAbiLity high-performance cement-based materials-ReSHEALience', funded by the European Union Horizon 2020 Research and Innovation Programme under GA No. 760824.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of tension stiffening and shrinkage on the flexural behavior of reinforced UHPFRC beams

  • Mezquida-Alcaraz, Eduardo J.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This paper presents a study on the flexural behavior of Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) beams, which included conventional reinforcing bars. The study focuses on critical design aspects, such as concrete shrinkage and cracking implications on the tension-stiffening phenomenon. An experimental program with two different sized flexural reinforced UHPFRC beams was run. Beams were cast and tested in a four-point bending test (4PBT) using UHPFRC with different amounts of fibers: 130 and 160 kg/m(3) (1.66% and 2.00% in vol.) to cover a wide range of strain-softening and strain-hardening constitutive UHPFRC behaviors. A nonlinear finite element model (NLFEM) was developed to validate the mechanical tensile characterization of UHPFRC when applied to reinforced elements. Both shrinkage and tension-stiffening effects were considered to improve the model. After the NLFEM simulation, very reliable results were obtained at both the service and ultimate load levels compared to the experimental ones. Finally, some aspects about the design of reinforced UHPFRC cross-sections under bending forces are addressed and satisfactorily compared to the experimental results., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain and the project "Rethinking coastal defence and Green-energy Service infrastructures through enHancEd-durAbiLity high-performance cement-based materials-ReSHEALience", funded by the European Union Horizon 2020 research and innovation programme under GA No 760824.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Direct procedure to characterize the tensile constitutive behavior of strain-softening and strain-hardening UHPFRC

  • Mezquida-Alcaraz, Eduardo J.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] There is a need to establish a complete process to characterize Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) in both strain-hardening and strain-softening tensile behavior. This process should be simple and easy to apply so that its application is direct. Therefore, this paper presents the development of a complete process to obtain the tensile constitutive parameters of UHPFRC. A simplified inverse analysis based on four-point bending tests (4PBT) to derive the tensile material properties of strain-hardening UHPFRC was adapted to be applied in the event of strain softening using a nonlinear finite element model (NLFEM). To fulfill this objective, an extensive experimental program was run with 227 UHPFRC specimens tested in 4PBT that exhibited strain-softening and strain-hardening tensile responses. As a reference, the characteristic UHPFRC tensile constitutive behavior was obtained. Finally, a predictive application capable of predicting tensile behavior using the experimental 4PBT curve as input was developed with the experimental database., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain and the European Union's Horizon 2020 ReSHEALience Project (Grant Agreement No. 760824)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Design and production of an experimental UHPFRC bending-active footbridge

  • Lazaro, Carlos|||0000-0001-7255-7068
  • Castro-Bugallo, M Carmen|||0000-0001-9201-6162
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Priego De Los Santos, Enrique|||0000-0001-6642-7806
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This paper describes the design, production and testing of an experimental footbridge made of ultra-highperformance fibre-reinforced concrete (UHPFRC). The prototype has a span length of 5.4 m and is made of a very slender pre-stressed UHPFRC deck (6 cm deep, 1.2 m wide), a 0.55 m high central deviator of the same material, and an external lower tensioning stainless-steel cable system. The service configuration of the structure involves a significant permanent bending of the deck, because of its slenderness; this initial bending is introduced in a controlled manner during the production process and prior to the installation, and results in an efficient, lightweight, and elegant structure with a high stiffness-to-self-weight ratio. The structural concept belongs to the category named active bending, which has been recent subject of research. Specifically, the structure is a bowstring system in which the bending-active member is made of UHPFRC, which constitutes the main novelty of this research. The suitability of UHPFRC as a material for bending active applications has been investigated, and a method to determine the limiting pre-stress of UHPFRC bending-active cross sections has been developed. The activation process and relevant limit states have been checked by means of a 3D frame finite-element model. The paper concludes with the description of the production process and the installation of the footbridge in the final location, as well as the successful results of the load tests and the geometric control of the novel footbridge prototype., The authors are grateful to Rover Maritime for facilitating the placement of the footbridge as access to their prototype in the H2020 Reshealience project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Self-healing efficiency of Ultra High-Performance Fiber-Reinforced Concrete through permeability to chlorides

  • Doostkami, Hesam
  • Roig-Flores, Marta
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This study presents a novel methodology to evaluate the self-healing capability of Ultra High-Performance FiberReinforced Concrete (UHPFRC) designed to compare conventional concrete types. The procedure used combines loading reinforced concrete elements until a fixed strain level to have a comparable total crack opening. Afterwards, water penetration to chlorides is used as an indicator of permeability. This work compares autogenous healing efficiency of a conventional concrete, a high-performance concrete, and two types of UHPFRCs with and without 0.8% of a crystalline admixture (CA) by the binder weight. The results show that all UHPFRC specimens exhibited excellent autogenous healing, higher than conventional concretes for an equivalent total crack. The self-healing results depended greatly on the crack size and the fiber content. Additionally, UHPFRCs with CA obtained the lowest water permeability after promoting self-healing for one month in water immersion and presented almost complete healing against chloride penetration, The activity described in this paper has been performed in the framework of the project 'Rethinking coastal defence and Green-energy Service infrastructures through enHancEd-durAbiLity high-performance cement-based materials-ReSHEALience', funded by the European Union Horizon 2020 research and innovation programme under GA No 760824. The authors would also like to thank Sika and Penetron for providing materials for the tests and E.J. Mezquida-Alcaraz for the characterization of UHPFRC mixes with Inverse Analysis.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Durability of UHPFRC functionalised with nanoadditives due to synergies in the action of sulphate and chloride in cracked and uncracked states

  • Giménez, Mercedes
  • Alonso, M. Cruz
  • Menéndez, Esperanza
  • Criado Sanz, María
This paper studies the durability of Ultra High Performance Fibre Reinforced Concrete (UHPFRC) with high Blast Furnace Slag content (BFS) and nanoadditives such as crystalline admixture (CA), alumina nanofibres (ANF) and cellulose nanocrystals (CNC), exposed to different aggressive environmental conditions: 1) three aggressive media: a) deionized water (dw), b)sulphate rich solution (ss) and c) simulated geothermal water (sgw) containing sulphate and chloride; 2) two water interactionconditions: a) static and b) dynamic (water impact); and 3) with and without the presence of cracks. Durability was analysed over24 months, measuring several physical and chemical parameters of the system, recording changes in both the aggressive mediaand the concrete. All UHPFRC types demonstrate good durability, showing high resistance to expansion and deformation in thesulphate-rich media. A leaching process occurs in all water interaction systems, the dynamic interaction in sgw being the mostaggressive. The interaction of sgw inside the crack favours the formation of solid phases such as calcium carbonates and ettringite, while the presence of nanoadditives affects the response of both the matrix and the formation of precipitates within the crack., The research activity reported in this paper was performed in the framework of the ReSHEALience project, which has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No. 760824. The authors also thank L. Ferrara and E. Cuenca (Department of Civil and Environmental Engineering, Politecnico di Milano) for casting the different UHDC mixes investigated.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Multi-performance experimental assessment of autogenous and crystalline admixturestimulated self-healing in UHPFRCCs: Validation and reliability analysis through an inter-laboratory study

  • Roig-Flores, M.
  • Alonso, M. Cruz
  • Serna, Pedro
  • Lo Monte, F.
  • Repesa, L.
  • Snoeck, D.
  • Doostkami, H.
  • Jackson, S.J.P.
  • Blanco, A.
  • Nasner, M.
  • Borg, R.P.
  • Schrofl, C.
  • Giménez, M.
  • de Belie, N.
  • Ferrara, L.
The huge benefits brought by the use of Ultra High-Performance Fibre-Reinforced Cementitious Composites (UHPFRCCs) include their high “intrinsic” durability, which is guaranteed by (1) the compact microstructure and (2) the positive interaction between stable multiple-cracking response and autogenous self-healing capability. Hence, self-healing capability must be properly characterized addressing different performances, thus providing all the tools for completely exploiting such large potential. Within this context, the need is clear for a wellestablished protocol for self-healing characterization. To this end, in the framework of the Cost Action CA15202 SARCOS, six Round Robin Tests involving 30 partners all around Europe were launched addressing different materials, spanning from ordinary concrete to UHPFRCC, and employing different self-healing technologies. In this paper, the tailored experimental methodology is presented and discussed for the specific case of autogenous and crystalline-admixture stimulated healing of UHPFRCC, starting from the comparison of the results from seven different laboratories. The methodology is based on chloride penetration and water permeability tests in cracked disks together with flexural tests on small beams. The latter ones are specifically aimed at assessing the flexural performance recovery of UHPFRCCs, which stands as their signature design “parameter” according to the most recent internationally recognized design approaches. This multi-fold test approach allows to address both inherent durability properties, such as through-crack chloride penetration and apparent water permeability, and more structural/mechanical aspects, such as flexural strength and stiffness., The round robin activity reported in this paper has been performed in the framework of the COST Action CA 15202 “SARCOS” (Self-healing As prevention Repair of COncrete Structures, http://www.sarcos.enq.cam.ac.uk). The production of the material and the inter-laboratory comparison were also supported by the ReSHEALience project (Rethinking coastal defence and Green-energy Service infrastructures through enHancEd-durAbiLity high-performance cement-based materials) which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 760824 (www.uhdc.eu)., Peer reviewed