Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Influence of the reference electrode position on the intensity corrosion measurements in reinforced concrete

  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
  • Gasch, Isabel|||0000-0001-7036-4481
  • Gandía-Romero, Jose M.|||0000-0003-0257-3286
[EN] Corrosion of the steel embedded in reinforced concrete is one the biggest problems that affects concrete structures durability. High alkalinity of this material protects the steel creating a passive layer, which chloride penetration or concrete carbonation destroy. In favourable conditions, as high humidity or oxygen presence, once the passive layer has been destroyed, active corrosion of the steel promotes loss of profile and reduces the adherence. The damage can be appreciated outside the elements once it is really advanced. Using methods to detect the beginning of active corrosion and control the damage can be a helpful tool to avoid expensive repairs after a late detection of the phenomena [1]. Including a sensor network in structures will let monitor the corrosion processes inside them. Voltammetric analysis using sensors requires a counter electrode (CE) and a reference electrode (RE). Due to economic issues and maintenance, most times it is just one reference embedded. This fact generates a large distance between the reference electrode and some sensors, incurring a wrong analysed values lecture. The aim of this paper is analysing the influence of the distance between sensors and the reference electrodes to get several measures which can let us arrange a statistic reliability. In this case, an external reference electrode will be used, letting move it, for measure at different distances from the sensor. For that purpose, in this studio will be used the voltammetric method, developed by Alcañiz et Al [2]., The authors would like to express their gratitude to the Universitat Politècnica de València for the pre-doctoral scholarship granted to Josep Ramon Lliso Ferrando (FPI-UPV2018), and the financial support from the Spanish Ministry of Economy and Competitiveness by the national program of oriented research, development and Innovation to societal challenges (ref. BIA2016-78460-C3-3-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of the droplet characteristics of a SCR injector spray through optical techniques

  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Postrioti, L.
  • Moreno-Gasparotto, Armando Enrique
  • Brizi, G.
[EN] The requirement of high-fidelity experimental data of microscopic properties of sprays motivates the continuous development of optical tools, since they are determinant in the understanding of atomization and evaporation process in a variety of multiphase flows.This work compares two optical techniques and an interferometry method for the measurement of the droplet size and velocity of a spray produced by a commercial Selective Catalytic Reduction (SCR) dosing unit also known as Urea Water Solution (UWS) injector. The adequate dosing and mixing of the injected fluid is fundamental for the proper functioning of the (SCR) system, therefore studying the spray characteristics with proper techniques is important to comprehend the phenomena occurring during the injection process. The SCR system is employed in the elimination of nitrous oxides present in exhaust gases of an engine. The objective is to compare the techniques in order to obtain accurate and reliable data that can be used to validate Computational Fluid Dynamics (CFD) models and improve current exhaust geometries and mixers. The studied techniques are Phase Doppler Anemometry (PDA), High Resolution Laser Backlight Imaging (HRLBI) and High Speed Microscopic Imaging (HSMI). The PDA determines the properties of the spray, obtaining the diameter and velocity of droplets in the axis parallel to the axis of the injector. With the HRLBI frames of 2040 x 2040 pixels were captured at different instants of the injection event, achieving a spatial resolution of 7 um/pixel, allowing the visualization of the smallest droplets present in the spray. With the HSMI videos of the spray using a fast camera and a microscopic lens were recorded at 150.000 fps to measure the diameter and the velocity of the droplets in 2 directions. The measurements were carried out using water as the injected fluid at 3 different injection pressures and the results are compared to determine the limits and advantages of each technique. The droplet diameter obtained by the PDA tests is similar to the observed results in the HRLBI, whereas the HSMI missed the smaller droplets. On the other hand the droplet velocity is in good concordance in the axis parallel to the axis of the injector, proving the HSMI a suitable technique to quantify the velocity of the droplets., The equipment used for the experiments was financially supported by MEMORIA IDIFEDER/2018/037 "Diagnostico optico a alta velocidad para el estudio de procesos termo-fluidodinamicos en sistemas de inyeccion" from Generalitat Valenciana. The Dipartimento di Ingegneria -University of Perugia is also acknowledged for the support to experimental activities with Ricerca di Base -2019 Program. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2018-S2-13), which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID). The Authors would like to thank Jose Enrique del Rey and Omar Huerta for their support in the experimental measurements.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Corrosion resistance of ultra-high performance fibre- reinforced concrete

  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Ramón Zamora, José Enrique
  • Soto Camino, Juan
[EN] The corrosion resistance of ultra-high performance concrete (UH) made with different fibre contents and under distinct curing conditions was studied. No signs of carbonation were observed after 1 year of accelerated carbonation testing (3% CO2). The fibreless UHs¿ electrical resistivity was above 5000 ¿·m, although these values were 2-fold higher than a UH with 1% fibres and approximately 5-fold higher than a UH with 2% fibres. Concrete resistance to chloride penetration was also extremely high (the diffusion coefficient equalled 1.3·10¿13 m2/s) and curing temperatures of 60 °C or 90 °C improved even more these properties, while lack of curing made them slightly worse. Given these excellent properties, the corrosion rate in specimens submerged in chloride solution for 1 year was negligible (iCORR from 0.007 to 0.025 µA/cm2). These values remained stable with time, unlike the 50 MPa concrete at 2 months when iCORR starting to increase and was 12-fold higher after 1 year. The time estimated for corrosion onset in UH is on average about 150-fold higher than that of 50 MPa., Authors thank to the Spanish Government the financial support of project BIA2016-78460-C3-3-R and to the European Union¿s Horizon 2020 the financial support of ReSHEALience project (Grant Agreement No. 760824). Furthermore, authors would like to express their gratitude for the support of the Universitat Politecnica de Valencia. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The predoctoral scholarship granted to Josep Ramon Lliso Ferrando within the program "Formacion de Personal Investigador" from the Universitat Politecnica de Valencia (FPI-UPV-2018) is also gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Desarrollo de formulaciones de ácido poliláctico (PLA) basadas en la incorporación de derivados de la colofonia

  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
[ES] Este trabajo de investigación tiene como objetivo general el desarrollo de formulaciones sostenibles a base de ácido poliláctico (PLA) mediante la incorporación de resinas naturales, resina de colofonia y derivados de resina de colofonia como agentes modificadores. La génesis de la presente tesis doctoral parte del interés de evaluar el efecto de los derivados de colofonia en las propiedades del PLA, tras observar los efectos positivos generados por estos aditivos en polímeros biodegradables de almidón termoplástico (TPS). Al tener como punto de partida los efectos positivos de los derivados de colofonia en el TPS, sería fácil continua la evaluación de los mismos aditivos en el PLA. Sin embargo, como secuencia razonable se comenzó por analizar los efectos de la propia resina de colofonia, y un derivado simple, continuando posteriormente con el análisis de derivados más complejas. Para finalizar con el análisis de derivados de colofonia en las propiedades del PLA, se utilizó un derivado experimental con el doble de complejidad. Este es derivado de colofonia con aducto de anhídrido maleico. A diferencia de la resina de colofonia, los derivados de colofonia presentan mayor estabilidad térmica y mayor estabilidad frente a la oxidación al aire libre. La evaluación de los efectos de la resina de colofonia y sus derivados en las propiedades del PLA se realizaron en cuatro estudios, compilados a su vez en tres grupos. Como epilogo de la investigación, se evaluó la posibilidad de incorporar la resina natural de la flor de Clusia rosea al ácido polilactico. Esta flor es conocida como Copey o mamey silvestre, la cual es una planta endémica del caribe. La evaluación del efecto de esta resina en el PLA se realizó como estudio número cinco, dando lugar a un último grupo, número cuatro. ¿ Grupo 1, uso de resinas de colofonia y un derivado común (ambos de bajo peso molecular). o Primer estudio ¿ Grupo 2, uso de dos derivados de colofonia (de alto peso molecular). o Segundo estudio ¿ Grupo 3, uso de derivado de colofonia con aducto de anhídrido maleico. o Tercer estudio o Cuarto estudio ¿ Grupo 4, evaluación de resina natural de flor de Clusia rosea. o Quinto estudio El procesado de los materiales se realizó por incorporación directa de los derivados de colofonia, mediante extrusión fundido. A continuación, las mezclas extruidas fueron trituradas en forma de granza o pellet, para posteriormente producir probetas normalizadas de ensayo mediante inyección por moldeo, las cuales se utilizaron en la caracterización., [CA] Aquest treball de recerca té com a objectiu general el desenvolupament de formulacions sostenibles a base d'àcid polilàctic (PLA) mitjançant la incorporació de resines naturals, resina de colofònia i derivats de resina de colofònia com a agents modificadors. La gènesi de la present tesi doctoral part de l'interés d'avaluar l'efecte dels derivats de colofònia en les propietats de l'àcid polilàctic, després d'observar els efectes positius generats per aquestos additius en polímers biodegradables de midó termoplàstic (TPS). En tindre com a punt de partida els efectes positius dels derivats de colofònia en el TPS, seria fàcil continuar l'avaluació dels mateixos additius en el PLA. No obstant això, com a seqüència raonable es va començar per analitzar els efectes de la pròpia resina de colofònia, i un derivat simple, continuant posteriorment amb l'anàlisi de derivats més complexos. Per a finalitzar amb l'anàlisi dels derivats de colofònia en les propietats del PLA, es va utilitzar un derivat experimental amb el doble de complexitat. Aquest és derivat de colofònia amb adducte d'anhídrid maleic. A diferència de la resina de colofònia, els derivats de colofònia presenten major estabilitat tèrmica i major estabilitat enfront de l'oxidació a l'aire lliure. L'avaluació dels efectes de la resina de colofònia i els seus derivats en les propietats del PLA es van realitzar en quatre estudis, compilats al seu torn en tres grups. Com epilogue de la investigació, es va avaluar la possibilitat d'incorporar la resina natural de la flor de Clusia rosea a l'àcid polilàctic. Aquesta flor és coneguda com Copey o mamey silvestre, la qual és una planta endèmica del caribe. L'avaluació de l'efecte d'aquesta resina en el PLA es va realitzar com a estudi número cinc, donant lloc a un últim grup, número quatre. ¿ Grup 1, ús de resines de colofònia i un derivat comú (tots dos de baix pes molecular). o Primer estudi ¿ Grup 2, ús de dos derivats de colofònia (d'alt pes molecular). o Segon estudi ¿ Grup 3, ús de derivat de colofònia amb adducte d'anhídrid maleic. o Tercer estudi o Quart estudi ¿ Grup 4, avaluació de resina natural de flor de Clusia rosea. o Cinqué estudi El processament dels materials es va realitzar per incorporació directa dels derivats de colofònia, mitjançant extrusió. A continuació, les mescles extruides van ser triturades en forma de gransa o pèl·let, per a posteriorment produir provetes normalitzades d'assaig mitjançant injecció per emotlament, les quals es van utilitzar en la caracterització., [EN] This research aims to develop sustainable formulations based on polylactic acid (PLA) by incorporating natural resin, rosin resin, and rosin resin derivatives as modifying agents. The genesis of this doctoral thesis is based on the interest in evaluating the effect of rosin resin derivatives on the properties of polylactic acid after observing the positive results generated by these additives in biodegradable polymers of thermoplastic starch (TPS). Having as a starting point the positive effects of rosin resin derivatives in TPS, it would be easy to continue evaluating the same additives in PLA. However, as a proper sequence, the evaluations were initiated by analyzing the effects of the rosin resin and a simple derivative, then continuing to investigate more complex derivatives. To finish with the analysis of rosin resin derivatives in the properties of PLA, an experimental rosin resin derivative with twice the complexity was used. This is a rosin resin derivative with maleic anhydride adduct. Unlike rosin resin, rosin resin derivatives exhibit higher thermal and oxidation stability. The effects evaluation of rosin resin and its derivatives in the properties of PLA were carried out in four studies. They were compiled into three groups. As an epilogue to this research, the possibility of incorporating the natural resin of the Clusia rosea flower into polylactic acid was evaluated. This flower is called Copey or wild mamey, an endemic plant native to the Caribbean. This resin effect in the PLA was evaluated as study number five, giving rise to the last group, number four. ¿ Group 1, use of rosin resin and a common derivative (both of low molecular weight). ¿ First study ¿ Group 2, use of two rosin resin esters (high molecular weight). ¿ Second study ¿ Group 3, use of rosin reisn derivative with maleic anhydride adduct. ¿ Their study ¿ Fourth study Group 4, evaluation of the natural resin from the Clusia rosea flower. ¿ Fith study The material was processed by directly incorporating the rosin resin derivatives by melt extrusion. Subsequently, the extruded mixtures were crushed as pellet to produce normalized testing samples through injection molding. These testing samples were then used in the characterization., Gracias a la Universitat Politècnica de València y al grupo de investigación DEMES por el apoyo a través del contrato predoctoral para la formación de personal investigador financiado por la estructura de investigación de la UPV – subprograma 2 (FPI-2018-S2-31946). Al Programa de Movilidad para estudiantes de doctorado de la Universitat Politècnica de València por la ayuda para “Estancias en Centros Extranjeros de Prestigio”.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Significance of macrocell currents in reinforced concrete columns partially immersed in seawater

  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Gasch, Isabel|||0000-0001-7036-4481
  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
  • Soto Camino, Juan
[EN] Corrosion in reinforced concrete structures located in marine environments is probably the main cause of damage, especially in elements that are partially immersed in seawater. The moisture gradient and different chloride concentrations occur in pieces under such conditions, which give way to the formation of macrocell currents between different rebar regions. Despite being studied by several authors who have run experiments in solution or with small test specimens, the significance of macrocell currents in structures has not yet been accurately quantified. The present work studied four columns that were partially immersed in seawater for more than 1 year, when the electrical resistance of concrete and the corrosion rate were monitored. After exposure, moisture and chloride content analyses were performed, and a rebar inspection was carried out. The obtained results show that macrocell currents can increase mass loss by rebar corrosion between 3- and 8-fold. They also reveal that macrocell currents can mitigate corrosion damage in areas showing cathodic performance., The authors thank the Spanish Government for Grant PID2020-119744RB-C21 funded by MCIN/AEI/10.13039/501100011033, and the support of the Universitat Politecnica de Valencia. They are also grateful for the predoctoral scholarship granted to Josep Ramon Lliso Ferrando as part of the "Formacion de Personal Investigador" programme of the Universitat Politecnica de Valencia (FPI-UPV-2018).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz-Lucas, María José
  • Martin Herreros, Jose
  • Tsolakis, Athanasios
[EN] The aim to reduce well to wheel emissions incentives the utilisation of alternative fuels (low to zero carbon content and/or low well to tank emissions) as well as the enhancement of engine efficiency. In parallel, the reduction of engine tailpipe emissions brings new challenges such as the decrease of the exhaust gas temperature. This trend penalises the ability of the exhaust aftertreatment system to eliminate pollutant emissions. In addition, the combustion of alternative fuels and new combustion modes induce changes in the nature and concentration of the exhaust species, which is known to affect the pollutants abatement mechanisms. This investigation provides new understanding on the sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels. The studied fuels are conventional diesel, alternative fuels (rapeseed methyl ester and gas to liquid) as well as propane using a dual-fuel combustion strategy. The research combines experimental conversion efficiency from genuine exhaust gases with modelling work useful to explain the reasons for the change in light-off temperature as a function of the fuel. In addition to the CO and NO impact, HC surrogates are proposed distinguishing species of different reactivity for each fuel based on the experimental HC speciation. The results highlight the role of the engine-out emissions on the pollutants conversion efficiency. Their fashion with different fuels contributes to evidence the interest for low engine-out emissions along with low light alkanes content in total HC, as promoted by alternative fuels, to reduce the oxidation light-off temperature., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of macrocell currents on rebar corrosion in reinforced concrete structures exposed to a marine environment

  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Gasch, Isabel|||0000-0001-7036-4481
  • Martínez-Ibernón, Ana|||0000-0003-2136-5650
  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
[EN] Autonomous corrosion monitoring systems in reinforced concrete structures tend to use sensors that are electrically isolated from rebars. This monitoring strategy ignores the macrocell currents that take place between active and passive areas of reinforcement. The effect of these currents has been studied on rebar corrosion in structures exposed to a marine environment. The results showed the existence of macrocell currents generates greater anodic polarisation in rebars¿ active areas, which favours chloride migration towards steel surface. As a result, corrosion onset takes place sooner, the concentration of the chlorides is higher, and the corrosion rate increases. When a rebar is in passive state, steel mass loss is negligible due to macrocell currents. However, after corrosion onset, the influence of these currents is greater the worse concrete quality is, and the smaller cover is. The corrosion rate showed differences of almost two orders of magnitude in concrete C30 and of one order of magnitude in concrete C50. When the total corrosion rate is determined only by measuring microcell currents, the obtained values tend to underestimate the mass loss due to corrosion by 90%. Conversely, when the analysis includes macrocell currents, a good fit between the theoretical and real values is obtained., The authors thank the Spanish Government for Grant PID2020-119744RB-C21 funded by MCIN/AEI/10.13039/501100011033, and the support of the Universitat Politecnica de Valencia. They are also grateful for the predoctoral scholarship granted to Josep Ramon Lliso Ferrando as part of the "Formacion de Personal Investigador" programme from the Universitat Politecnica de Valencia (FPI-UPV-2018) , and Grant FPU 16/00723 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Using momentum flux measurements to determine the injection rate of a commercial Urea Water Solution injector

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Moreno-Gasparotto, Armando Enrique
[EN] The Selective Catalytic Reduction (SCR) technology allows the transformation of the Nitrous Oxide emissions present in exhaust gases into gaseous nitrogen and water. For a proper operation of the SCR, a urea-water solution (UWS) injector must dose an adequate amount of liquid into the exhaust pipe in order to avoid deposit formation and to guarantee the SCR system efficiency. This task requires the knowledge of the performance of the injector. Then, the goal of this work is to study the hydraulic performance of a UWS injector, by means of measuring the spray momentum flux in order to understand the influence of different variables as injected fluid, injection pressure, counter pressure and cooling temperature of the injector on the flow characteristics. The tested injector was cooled at three different temperatures, 60, 90 and 120 degrees C, the injection pressure of the UWS was set at 5, 7 and 9 bar, with counter pressures of 750, 900, 1000 and 2000 mbar for the two tested fluids, water and UWS. The measurements were carried out using an experimental facility developed at CMT-Motores Termicos for the determination of spray momentum flux, where a piezoelectric pressure sensor was located near the nozzle exit of the injector, which measures the impact force of the spray. Additionally, the proposed methodology allowed to determine the injected mass flow and to capture the transient injection events, such as the opening and closing stages. Moreover, mass flow rate measurements of the injector were performed under the same operating conditions, determining the influence of the injection pressure, cooling temperature, counter pressure and fluid properties. Regarding the pressure, the tendency was as expected, the higher the injection pressure the higher the Momentum flux and flow rate. Results showed that an increment of the cooling temperature of the injector induces the appearance of flash boiling conditions, having an impact on the total injected mass and momentum flux, changing the behaviour of the spray. For the same conditions, water has a higher momentum flux than the UWS due to differences in fluid properties and velocity at the nozzle exit., This work has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018099706B100. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI2018S213) , which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of the cell geometry on the conversion efficiency of oxidation catalysts under real driving conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz, María José
  • Martín Herreros, José
  • Tsolakis, Athanasios
[EN] Worldwide pollutant regulations applied to the transportation sector are progressively tightening the emission limits and widening the operating conditions of the type approval tests. As a result, the layout and thermal management of the exhaust system is becoming highly complex looking to achieve early catalytic converter activation. On this regard, the monolith meso-geometry plays a primary role to optimise the pollutants con -version efficiency. The geometrical characteristics simultaneously affect and trade-off multiple flow phenomena as the exhaust gas is transported through the channels. These include the bulk gas and internal pore diffusion towards the active sites in addition to the heat transfer including convection, radial conductivity and thermal capacitance. In this work, the impacts of the cell size, cross-section shape, washcoat loading and substrate material on CO and HC conversion efficiency have been investigated under representative real driving condi-tions. From the real driving conditions experimental data, the study decouples the influence of the washcoat loading from the cell size and material applying a catalytic converter model. Detailed expressions are provided for the calculation of the specific surfaces and heat and mass transfer parameters as a function of the cell and washcoat meso-geometry in square and triangular cells. Therefore, this work enables to identify the processes which govern the catalytic abatement of pollutant emissions. In particular, the role of the gas and washcoat specific surfaces is highlighted because of its importance on the optimization of the mass transfer process by means of a proper cell geometry selection. In parallel, the differences in the change of the CO and HC abatement patterns, which are explained by the characteristic CO emission spikes in accelerations and the HC accumulation, contribute to evidence the limitations on the conversion efficiency benefit that the optimum cell geometry and washcoat loading can provide., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018-S2-10.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of Pre-Turbine Small-Sized Oxidation Catalyst on Engine Performance and Emissions under Driving Conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Ruiz-Lucas, María José
[EN] The earlier activation of the catalytic converters in internal combustion engines is becoming highly challenging due to the reduction in exhaust gas temperature caused by the application of CO2 reduction technologies. In this context, the use of pre-turbine catalysts arises as a potential way to increase the conversion efficiency of the exhaust aftertreatment system. In this work, a small-sized oxidation catalyst consisting of a honeycomb thin-wall metallic substrate was placed upstream of the turbine to benefit from the higher temperature and pressure prior to the turbine expansion. The change in engine performance and emissions in comparison to the baseline configuration are analyzed under driving conditions. As an individual element, the pre-turbine catalyst contributed positively with a relevant increase in the overall CO and HC conversion efficiency. However, its placement produced secondary effects on the engine and baseline aftertreatment response. Although small-sized monoliths are advantageous to minimize the thermal inertia impact on the turbocharger lag, the catalyst cross-section is in trade-off with the additional pressure drop that the monolith causes. As a result, the higher exhaust manifold pressure in pre-turbine pre-catalyst configuration caused a fuel consumption increase higher than 3% while the engine-out CO and HC emissions did around 50%. These increments were not completely offset despite the high pre-turbine pre-catalyst conversion efficiency (>40%) because the partial abatement of the emissions in this device conditioned the performance of the close-coupled oxidation catalyst., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Design of a new methodology for the study of internal flow behaviour in radial turbines

  • Hervás Gómez, Natalia
[ES] Los compresores centrífugos y turbinas radiales aplicadas al campo de la sobrealimentación tienen un alto rendimiento, pero cuando ambos sistemas trabajan fuera del punto de diseño este disminuye debido a varias razones entre las que están las perdidas mecánicas, por ventilación, por diseño y por comportamiento dinámico del flujo que atraviesa las superficies aerodinámicas de sus componentes. En esta tesis se aborda un estudio para llegar a un diseño de experimento que permita relacionar los parámetros de funcionamiento de una turbina radial de geometría variable lejos del punto óptimo de diseño con el comportamiento del flujo interno en la zona de la voluta y el estator. El presente trabajo se focaliza en describir y argumentar los procesos que ocurren en una turbina radial con estator de geometría variable estudiando el comportamiento del flujo a través de la geometría interna. La evaluación se realiza en puntos de funcionamiento fuera de diseño hasta alcanzar la frontera de condición de choque en los canales del estator para distintas aperturas. Primeramente, se ha caracterizado el mapa de funcionamiento de la turbina para distintas aperturas del estator en un banco experimental. Luego, se ha digitalizado la geometría interna de la turbina en 3D para tener un modelo detallado de la misma. El modelo ha sido implementado en un programa de uso comercial de cálculo CFD. Los resultados obtenidos de la modelización de distintos puntos de funcionamiento del mapa de la turbina en el programa CFD han servido para realizar un análisis detallado del patrón de flujo dentro de la turbina, identificando y cuantificando los fenómenos más importantes bajo diferentes condiciones de operación. Se han llevado a cabo simulaciones estacionarias usando RANS y no estacionarias (unsteady RANS) para obtener las características del flujo en la zona de la voluta, el estator y el rotor. La validación del modelo se ha logrado interponiendo el resultado de los puntos obtenidos en CFD en el mapa experimental. Para analizar la interacción las distintas geometrías internas y el fluido que las atraviesa se llevaron a cabo simulaciones numéricas con los vanos del estator en una posición cerrada, 10% VGT, y en dos posiciones más abiertas, 30% y 80%. La desviación de las líneas de corriente de su recorrido por el estator está condicionada por la apertura y por acción del rotor a partir del 50% de la cuerda de los vanos. Esta situación es perjudicial para la eficiencia de la turbina. Cerca de los vanos del estator, las pérdidas de presión son altas, hacia el centro del espacio sin vanos las pérdidas disminuyen y cerca del rotor empiezan a incrementar. Caracterizar experimentalmente el flujo interno incrementa su dificultad cuando se necesitan detalles sobre el comportamiento de las líneas de corriente entre los canales del estator, por lo tanto, un punto importante en el desarrollo de este trabajo ha sido la propuesta, diseño y puesta a punto de un experimento basado en incrementar el tamaño de la turbina. El estudio de factor de escala determinó un tamaño adecuado de 3:1. Para validar el tamaño se realizaron pruebas con el modelo CFD validado. La nueva turbina a escala se produjo a partir de la base de datos digitalizada empleando un material no poroso, con tolerancia a la presión (5bar) y temperatura (473K) de fácil acceso intrusivo para instrumentos de medida de presión y temperatura para ser colocados en los accesos de la entrada y salida de los canales del estator, así como en el propio interior del canal. El experimento de la turbina a escala ha dado como resultado valores de velocidades en distintas zonas del canal que fueron comparadas con los resultados obtenidos en la turbina a escala en modelo digital CFD. La creación de dicho experimento supone el concepto de desarrollo de estudios basados en la disminución de perdidas en la turbina por mejora del comportamiento del flujo interno interactuando con los vanos móviles del estator., [CA] Els compressors centrífugs i turbines radials aplicades al camp de la sobrealimentació tenen un alt rendiment, però quan tots dos sistemes treballen fora del punt de disseny el valor es deprecia causat per diverses raons entre les quals es poden trobar perdudes mecàniques, perdudes per ventilació, perdudes per disseny i pèrdues per comportament dinàmic del flux que travessa les superfícies aerodinàmiques dels components. En aquesta tesi saborda un estudi per arribar a un disseny d'experiment que permeti relacionar els paràmetres de funcionament d'una turbina radial de geometria variable lluny del punt òptim de disseny amb el comportament del flux intern a la zona de la voluta i l'estator. Aquest treball es focalitza a descriure i argumentar els processos que ocorren en una turbina radial amb estator de geometria variable estudiant el comportament del flux a través de la geometria interna. L'avaluació es realitza en punts de funcionament fora de disseny fins a assolir la frontera de condició de xoc als canals de l'estator formats per les obertures per a diferents posicions d'aquests. Primerament, s'ha caracteritzat el mapa de funcionament de la turbina per a diverses posicions d'obertura dels canals de l'estator en un banc experimental. Després, s'ha digitalitzat la geometria interna de la turbina en tres dimensions per tenir-ne un model detallat. El model ha estat implementat en un programa dús comercial de càlcul computacional fluidodinàmic. Els resultats obtinguts de la modelització de diferents punts de funcionament del mapa de la turbina al programa CFD han servit per fer una anàlisi detallada del patró de flux dins de la turbina, identificant i quantificant els fenòmens més importants sota diferents condicions d'operació. S'han dut a terme simulacions estacionàries usant RANS i no estacionàries (unsteady RANS) per obtenir les característiques del flux a la zona de la voluta, l'estator i el rotor. La validació del model s'ha aconseguit interposant el resultat dels punts obtinguts en CFD al mapa experimental. Per analitzar la interacció les diferents geometries internes i el fluid que les travessa es van dur a terme simulacions numèriques amb les obertures de l'estator en una posició tancada, 10% VGT, i en dues posicions més obertes, 30% i 80%. La desviació de les línies de corrent del recorregut per l'estator està condicionada per l'obertura i per acció del rotor a partir del 50% de la corda de les obertures. Aquesta situació és perjudicial per a l'eficiència de la turbina. A prop de les obertures de l'estator, les pèrdues de pressió són altes, cap al centre de l'espai sense obertures disminueixen i prop del rotor comencen a incrementar. Caracteritzar experimentalment el flux intern incrementa la seva dificultat quan es necessiten detalls sobre el comportament de les línies de corrent entre els canals de l'estator, per tant, un punt important en el desenvolupament d'aquest treball ha estat la proposta, el disseny i la posada a punt de un experiment basat en incrementar el mida de la turbina. L'estudi de factor d'escala va a determinar una mida adequada de 3:1. Per validar la mida es van realitzar proves amb el model CFD validat. La nova turbina a escala es va produir a partir de la base de dades digitalitzada emprant un material no porós, amb tolerància a la pressió (5bar) i temperatura (473K) de fàcil accés intrusiu per a instruments de mesura de pressió i temperatura per ser col·locats als accessos de l'entrada i sortida dels canals de l'estator, així com al propi interior del canal. L'experiment de la turbina a escala ha donat com a resultat valors de velocitats a diferents zones del canal que van ser comparades amb els resultats obtinguts a la turbina a escala en model digital CFD. La creació d'aquest experiment suposa el concepte de desenvolupament d'estudis basats en la disminució de pèrdues a la turbina per millora del comportament del flux intern interactuant amb les obertures mòbils de l'estator., [EN] Centrifugal compressors and radial turbines applied to the field of supercharging have a high performance, but when both systems work outside the design point the value depreciates caused by several reasons among which can be found mechanical losses, ventilation losses, design losses and losses due to dynamic behavior of the flow that crosses the aerodynamic surfaces of its components. In this thesis a study is addressed to reach a design of experiment that allows relating the operating parameters of a variable geometry radial turbine far from the optimum design point with the behavior of the internal flow in the volute and stator area. The present work is focused on describing and arguing the processes that occur in a radial turbine with a variable span positioning stator by studying the behavior of the flow through the internal geometry. The evaluation is performed at off-design operating points until reaching the shock condition boundary in the stator channels formed by its blades for different positions of these. First, the turbine operating map has been characterized for different opening positions of the stator channels on an experimental bench. Then, the internal geometry of the turbine was digitized in three dimensions in order to have a detailed model of the turbine. The model has been implemented in a commercially available fluid dynamic computational program. The results obtained from the modeling of different operating points of the turbine map in the CFD program have been used to perform a detailed analysis of the flow pattern inside the turbine, identifying and quantifying the most important phenomena under different operating conditions. Stationary simulations have been carried out using Reynolds Averaged Navier Stokes (RANS) and non-stationary (unsteady RANS) to obtain the flow characteristics in the volute, stator and rotor zones. The validation of the model has been achieved by interposing the result of the points obtained in CFD on the experimental map. To analyze the interaction between the different internal geometries and the fluid flowing through them, numerical simulations were carried out with the stator vanes in a closed position, 10% VGT, and in two more open positions, 30% and 80% VGT. The deviation of the current lines from their path through the stator is conditioned by the opening and by rotor action from 50% of the span chord. This situation is detrimental to turbine efficiency. Near the stator vanes, the pressure losses are high, towards the center of the spanless space the losses decrease and near the rotor they start to increase. Experimentally characterizing the internal flow increases its difficulty when details on the behavior of the streamlines between the stator channels are needed, therefore, an important point in the development of this work has been the proposal, design and set-up of an experiment based on increasing the turbine size. The scale factor study determined an adequate size of 3:1. To validate the size, tests were performed with the validated CFD model. The new scaled turbine was produced from the digitized database using a non-porous, pressure (5 bar) and temperature (473 K) tolerant material with easy intrusive access for pressure and temperature measuring instruments to be placed at the inlet and outlet accesses of the stator channels, as well as the stator and the stator. The scale turbine experiment has resulted in values of velocities in different areas of the channel that were compared with the results obtained in the scale turbine in a digital CFD model. The creation of this experiment implies the concept of developing studies based on the reduction of losses in the turbine by improving the behavior of the internal flow interacting with the moving stator vanes., Me gustaría dar las gracias a la beca del "Programa de Apoyo para la Investigación y Desarrollo (PAID-01-18)" para estudios de doctorado (FPI-2018-S2-1368).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental approach for the analysis of the flow behaviour in the stator of a real centripetal turbine

  • Galindo, José|||0000-0001-6068-182X
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Hervás-Gómez, Natalia
[EN] During normal operation, radial turbines may work in off-design conditions. Off-design conditions may be characterised by very low expansion ratios, very high expansion ratios, very low rotational speeds or very high rotational speeds. All of these cases are difficult to characterise experimentally due to high experimental uncertainties or a lack of capabilities in the system feeding pressurised air to the turbine. Also, there are two- and three-dimensional computational fluid dynamics simulations at these operating points but could not be accurate enough due to high turbulence effects, flow detachment and shock wave generation. With a lack of high-quality data, experimental or computational, to fit the reduced-order turbine models used in zero- and one-dimensional engine simulations, there are large uncertainties associated to their results in off-design conditions. This work develops an experimental facility able to characterise the internal flow of radial turbine stators in terms of pressure and velocity fields at off-design and regular working conditions. The facility consists of an upscaled model of a radial turbine volute and stator fed with air in pressure- and temperature-controlled conditions, so different sensors can be used inside it with the least amount of flow disturbance. The different restrictions considered in the design of the upscaled model are presented, and their effects in the final experimental apparatus capabilities are discussed. A preliminary comparison between computational fluid dynamics simulations and experimental data shows encouraging results., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the programme 'Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain'. The support given to Ms N.H.G. by Universitat Politecnica de Valencia through the 'FPI-Subprograma 2' (No. FPI-2018-S2-1368) grant within the 'Programa de Apoyo para la Investigacion y Desarrollo (PAID-0118)' is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Investigation of the urea-water solution atomization process in engine exhaust-like conditions

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Moreno-Gasparotto, Armando Enrique
[EN] The injection process of the urea-water solution (UWS) determines the initial conditions for the mixing and evaporation of the fluid in the selective catalytic reduction system. In this study, the liquid atomization process of a UWS dosing system is investigated using optical diagnosis through back-light imaging. The droplet diameter distribution and the droplet velocity (in the axial and tangential components) of the liquid spray are quantified under different air flow and injection conditions. A new test facility was designed to study UWS spray under conditions that resemble those of the engine exhaust pipe, which is capable of reaching an air flow of 400 kg/h and air temperatures up to 400 degrees C. The test matrix consisted of variations in the air flow temperature, air mass flow and UWS injection pressure. A high speed camera was used for capturing the images of the liquid spray, comparing the atomized liquid behaviour in three different regions of the plume: the first one near the nozzle exit, and the other two in the developed region of the spray (one aligned with the injector axis and the other at the spray periphery). Increasing the injection pressure affected the atomization process producing smaller particles with higher velocities in the axial and tangential components, promoting wider global spray angles, that combined with high air flow temperatures could improve the evaporation and mixing process in the SCR system. The main contribution is the development of an alternative technique for the quantification of the droplet size and velocity., The equipment used for the experiments was financially supported by IDIFEDER2018 from Generalitat Valenciana. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2018-S2-13), which is included within the framework of Programa de Apoyo para la Investigacien y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Design and Numerical Analysis of Flow Characteristics in a Scaled Volute and Vaned Nozzle of Radial Turbocharger Turbines

  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Navarro, Roberto|||0000-0003-2587-4954
  • Inhestern, Lukas Benjamin
  • Hervás-Gómez, Natalia
[EN] Over the past few decades, the aerodynamic improvements of turbocharger turbines contributed significantly to the overall efficiency augmentation and the advancements in downsizing of internal combustion engines. Due to the compact size of automotive turbochargers, the experimental measurement of the complex internal aerodynamics has been insufficiently studied. Hence, turbine designs mostly rely on the results of numerical simulations and the validation of zero-dimensional parameters as efficiency and reduced mass flow. To push the aerodynamic development even further, a precise validation of three-dimensional flow patterns predicted by applied computational fluid dynamics (CFD) methods is in need. This paper presents the design of an up-scaled volute-stator model, which allows optical experimental measurement techniques. In a preliminary step, numerical results indicate that the enlarged geometry will be representative of the flow patterns and characteristic non-dimensional numbers at defined flow sections of the real size turbine. Limitations due to rotor-stator interactions are highlighted. Measurement sections of interest for available measurement techniques are predefined., The authors disclose receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the program "Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain". The support given to Ms. N.H.G. by Universitat Politecnica de Valencia through the "FPI-Subprograma 2" (No.FPI-2018-S2-1368) grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-18)" is gratefully acknowledged
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Modelling of Heat Losses through Coated Cylinder Walls and their Impact on Engine Performance

  • Escalona Cornejo, Johan Enrique
[ES] Actualmente, los vehículos propulsados por motores de combustión interna alternativos (MCIA) constituyen uno de los mayores agentes contaminantes para el medio ambiente. En este sentido, ha existido una importante cooperación internacional para promulgar leyes que regulen las emisiones contaminantes. De manera que los fabricantes de coches han impulsado el desarrollo de tecnologías más limpias y amigables con el medio ambiente. Ante esta situación, ha surgido recientemente la electrificación, como uno de los proyectos más ambiciosos de la industria automotriz para los próximos años. Sin embargo, esta meta parece aún lejana en el horizonte. En tal sentido, la hibridación con motores térmicos y eléctricos parece ser el camino a seguir en el corto plazo. Por consiguiente, los MCIA seguirán siendo la principal fuente de propulsión terrestre durante los años venideros. Para mitigar los inherentes efectos contaminantes de los motores de combustión interna, se han propuesto diferentes tecnologías para desarrollar motores más eficientes. Entre ellas, la aplicación de recubrimientos térmicos en las paredes de la cámara de combustión apunta a reducir las pérdidas por calor en el motor, y así aumentar su eficiencia térmica. El objetivo principal de esta tesis es estudiar el impacto de aplicar recubrimientos térmicos en las paredes de la cámara de combustión en motores de combustión interna. En este sentido, determinar los flujos de calor experimentalmente a través de las paredes es complicado y no del todo fiables, debido a que dependen de la medición de las temperaturas de pared. Por este motivo, el CFD-CHT es utilizado. El primer paso fue validar la herramienta computacional que es utilizada para los cálculos en motores de combustión interna. Para ello se realizó un estudio preliminar en geometrías sencillas como una tubería circular o un canal rectangular. Se evaluaron los modelos de transferencia de calor y se determinó la relevancia de ciertos parámetros como la rugosidad. Para complementar el estudio, se realizó un análisis de las temperaturas en una geometría más realista como el pistón de un MCIA. Los valores de temperatura calculados por el software fueron casi iguales a las medidas experimentales. Por consiguiente, la fiabilidad de la herramienta computacional fue verificada. Seguidamente, se plantea una metodología para abordar al problema de modelar capas muy finas de recubrimientos térmicos en el espacio tridimensional. Para de esta manera poder simular las paredes recubiertas en la cámara de combustión. La metodología consiste en definir un material equivalente con un espesor y número de nodos que permitan un mallado computacionalmente realista. Para ello se utilizó un DoE en combinación con un análisis de regresión múltiple. Los primeros estudios se llevaron a cabo en un motor de gasolina. El modelado se llevó a cabo para dos configuraciones: motor con paredes metálicas y motor con pistón y culata recubiertos. A través de un análisis exhaustivo de la transferencia del calor, se evaluó el impacto que tenía aplicar el revestimiento térmico en el motor. La comparación con datos experimentales demuestran la utilidad del cálculo CHT para evaluar las pérdidas de calor en un MCIA. Sin embargo, ninguna mejora fue observada en el motor de gasolina debido al tipo de recubrimiento aplicado en las paredes de la cámara de combustión. Las simulaciones llevadas a cabo en el motor de gasolina permitieron determinar que los cálculos CHT son computacionalmente largos. En este sentido, una serie de estrategias diseñadas a optimizar los cálculos han sido analizadas con el fin de reducir los tiempos de cálculo. A través de este estudio, se encontró una metodología para optimizar la malla del dominio computacional. Esta última, emplea un refinamiento AMR basado en la distancia de pared. Este método es utilizado para modelar el impacto de aplicar un revestimiento tér, [CA] Actualment, els vehicles propulsats per motors de combustió interna alter- natius (MCIA) constitueixen un dels majors agents contaminants per al medi ambient. En aquest sentit, ha existit una important cooperació internacional per a promulgar lleis que regulen les emissions contaminants. De manera que els fabricants de cotxes han impulsat el desenvolupament de tecnologies més netes i amigables amb el medi ambient. Davant aquesta situació, ha sorgit recentment l'electrificació, com un dels projectes més ambiciosos de la indústria automotriu per als pròxims anys. No obstant això, aquesta meta sembla encara llunyana en l'horitzó. En tal sentit, la hibridació amb motors tèrmics i elèctrics sembla ser el camí a seguir en el curt termini. Per consegüent, els MCIA continuaran sent la principal font de propulsió terrestre durant els anys esdevenidors. Per a mitigar els inherents efectes contaminants dels motors de combustió interna, s'han proposat diferents tecnologies per a desenvolupar motors més eficients. Entre elles, l'aplicació de recobriments tèrmics en les parets de la cambra de combustió apunta a reduir les pèrdues per calor en el motor, i així augmentar la seua eficiència tèrmica. L'objectiu principal d'aquesta tesi és estudiar l'impacte d'aplicar reco- briments tèrmics en les parets de la cambra de combustió en motors de combustió interna. En aquest sentit, determinar els fluxos de calor experi- mentalment a través de les parets és complicat i no del tot fiable, pel fet que depenen del mesurament de les temperatures de paret. Per aquest motiu, el CFD-CHT (Computational fluid dynamics-Conjugate Heat Transfer) és utilitzat. El primer pas va ser validar l'eina computacional que és utilitzada per als càlculs en motors de combustió interna. Per a això es va realitzar un estudi preliminar en geometries senzilles com una canonada circular o un canal rectangular. Es van avaluar els models de transferència de calor i es va determinar la rellevància de certs paràmetres com la rugositat. Per a complementar l'estudi, es va realitzar una anàlisi de les temperatures en una geometria més realista com el pistó d'un MCIA. Els valors de temperatura calculats pel software van ser quasi iguals a les mesures experimentals. Per consegüent, la fiabilitat de l'eina computacional va ser verificada. Seguidament, es planteja una metodologia per a abordar el problema de modelar capes molt fines de recobriments tèrmics en l'espai tridimensional, per a d'aquesta manera poder simular les parets recobertes en la cambra de combustió. La metodologia consisteix a definir un material equivalent amb una grossària i nombre de nodes que permeten un mallat computacionalment realista. Per a això es va utilitzar un DoE (Design of experiments) en combinació amb una anàlisi de regressió múltiple. Els primers estudis es van dur a terme en un motor de gasolina. El mod- elatge es va dur a terme per a dues configuracions: motor amb parets metàl·liques i motor amb pistó i culata recoberts. A través d'una anàlisi exhaustiva de la transferència de la calor, es va avaluar l'impacte que tenia aplicar el revestiment tèrmic en el motor. La comparació amb dades experi- mentals demostren la utilitat del càlcul CHT per a avaluar les pèrdues de calor en un MCIA. No obstant això, cap millora va ser observada en el motor de gasolina a causa de la mena de recobriment aplicada en les parets de la cambra de combustió. Les simulacions dutes a terme en el motor de gasolina van permetre determinar que els càlculs CHT són computacionalment llargs. En aquest sentit, una sèrie d'estratègies dissenyades per a optimitzar els càlculs han sigut analitzades amb la finalitat de reduir els temps de càlcul. A través d'aquest estudi, es va trobar una metodologia per a optimitzar la malla del domini computacional. Aquesta última, empra un refinament AMR basat en la distància de paret., [EN] Currently, vehicles powered by internal combustion engines (ICE) are targeted as contributing largely to environmental pollution. In this regard, there has been significant international cooperation to enact laws that regulate the polluting emissions. Hence, the car manufacturers have oriented efforts to the development of cleaner and more eco-friendly technologies. In order to face this situation, electrified vehicles have emerged as one of the most promising projects in the automotive industry for the coming years. However, this target still seems far on the horizon. In this sense, hybridization with thermal and electric engines seems to be the path to follow in the short term. Consequently, ICEs will continue to be one of the important sources of terrestrial propulsion in the coming years. To mitigate the inherent polluting effects of internal combustion engines, different technologies have been proposed to develop more efficient engines. Among them, the application of thermal coatings on the combustion chamber walls. This technology aims at reducing the heat losses in the engine, and thus increase its thermal efficiency. The main objective of this thesis is to study the impact of coating the combustion chamber walls of an engine on heat losses and thermal efficiency. The experimental definition of the heat fluxes through the walls is complex and not very reliable because it requires the measurement of wall temperatures. For this reason, CFD-CHT (Computational fluid dynamics-Conjugate Heat Transfer) is used. The first step was to validate the computational tool employed for CFD-CHT calculations in internal combustion engines. For this, a preliminary study in simple geometries such as a circular pipe or a rectangular channel was performed. Heat transfer models were evaluated and the relevance of certain parameters such as roughness was determined. To reinforce the study, a thermal analysis in a more realistic geometry such as the piston of a CI engine was carried out. The temperature values calculated by the software were almost the same as the experimental measurements. Consequently, the reliability of the computational tool was verified. Next, a methodology was proposed to address the problem of modeling very thin layers of thermal coating for three-dimensional CFD-CHT calculations. The methodology consists in defining an "equivalent material" with a thickness and number of nodes that allow a computationally realistic mesh. For this, a DoE in combination with a multiple regression analysis was employed. The first CFD-CHT simulations in ICEs were carried out for a gasoline engine. The study was performed for two configurations: metallic engine and engine with coated piston and cylinder head. An exhaustive heat transfer analysis was made in order to determine the impact of applying the thermal coating on the engine. Comparison with experimental data proved the suitability of the CHT calculations to evaluate heat losses in ICEs. However, no improvement on engine efficiency was observed in the gasoline engine due to the type of coating applied on the combustion chamber walls. Experience with the gasoline engine calculations showed that CHT calculations were very time consuming. In this regard, some strategies aimed at optimizing the calculations were analyzed in order to reduce calculation times. The most successful methodology was based on AMR cell refinement to optimize the mesh and reduce significantly the computational costs. This approach was used to study the impact of applying a new generation thermal coating on the piston top of a Diesel engine. The results obtained indicated that this type of coating allows for some improvement in the thermal efficiency of the engine without affecting its performance., The author wishes to acknowledge the financial support received through contract FPI-2018-S2-1205 of the Programa para la Formación de Personal investigador (FPI) 2018 of Universitat Politècnica de València. Parts of the work presented in this thesis have received funding from the European Union’s Horizon 2020 research and innovation programme undergrant agreement No 724084.The author wishes to thank IFPEN for their permission to use their single cylinder engine geometry and experimental results, as well as Saint Gobain Research Provence for providing the coating characteristics.The respondent wants to express its gratitude to CONVERGENT SCIENCE Inc. and Convergent Science GmbH for their kind support for performingthe CFD-CHT calculations using CONVERGE software
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Performance of a diesel oxidation catalyst under diesel-gasoline reactivity controlled compression ignition combustion conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Ruiz, María José
[EN] Reactivity controlled compression ignition is a promising combustion strategy due to the combination of excellent thermal efficiency with ultra-low nitrogen oxides and particulate matter raw emissions. However, very high levels of unburned hydrocarbons and carbon monoxide emissions are found. It limits the reactivity controlled compression ignition use at very low loads and presents an additional challenge for the diesel oxidation catalyst. The low exhaust temperature and high carbon monoxide and hydrocarbon concentration can penalise the catalyst conversion efficiency. The objective of this work is to evaluate the response of an automotive diesel oxidation catalyst when used for reactivity controlled compression ignition combustion combining experimental and modelling approaches. For this purpose, dedicated tests have been done using diesel-gasoline as fuel combination in a single-cylinder engine. This way, the catalyst conversion efficiency has been determined within a wide operating range covering hydrocarbon adsorption conditions and the pollutants abatement dependence on the mass flow and temperature. The experimental results in the full-size catalyst has been analysed by modelling. A lumped diesel oxidation catalyst model has been applied to extend the results to multi-cylinder engine conditions and to determine the light-off curves for both carbon monoxide and hydrocarbons. These tests evidence the penalty in light-off temperature due to high pollutants mass fraction, which promotes inhibition limitations to the reaction rate., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018S2-10.