Pasar al contenido principal

ESTUDIO DE LA ATOMIZACION PRIMARIA MEDIANTE SIMULACIONES DNS Y TECNICAS OPTICAS DE MUY ALTA RESOLUCION

RTI2018-099706-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 21
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental analysis of the injection pressure effect on the near-field structure of liquid fuel sprays

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • González-Montero, Lucas Antonio
[EN] Primary atomization and initial spray development are critical in the operation of high-pressure liquid sprays such as the ones used in internal combustion engines. In the current paper, an analysis of the effect of the fuel injection pressure on the near-nozzle spray morphology is performed. For this purpose, a high-magnification diffused backlight imaging technique is set by means of a high-speed light-emitting diode and a long-distance microscope. The technique allows to visualize the first 2 mm of the spray development with a resolution of approximately 250 pixels per millimeter. The images obtained are processed with two different criteria to define the spray contour: one using an optical thickness threshold and a second one based on the intensity derivative on the radial direction. The analysis is focused on three aspects of the spray morphology: the spray angle, its standard deviation, and the standard deviation of the spray contour itself. The results show that the average spray angle is only slightly affected by the injection pressure, being the discharge density the main boundary condition affecting this parameter. Instead, the two standard deviation parameters show a clear increasing trend with the injection pressure, confirming that higher turbulence at the nozzle outlet induces higher variability in the spray shape. Regarding the two contour detection methodologies, similar values are reached in the average spray angle, while some more impact is seen in the spray dispersion, although the same trends are found, This research has been funded by the Spanish Ministerio Ciencia e Innovacion through the project RTI2018-099706-B-100: "Estudio de la atomizacion primaria mediante simulaciones DNS y tecnicasopticas de muy alta resolucion". Gonzalez-Montero L.A. is partially supported though the contract FPI - Subprograma 2 of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

ECN Spray D visualization of the spray interaction with a transparent wall under engine-like conditions. Part I: Non-reactive impinging spray

  • Peraza, Jesús E.
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Ruiz-Rosales, Santiago|||0000-0001-9536-3696
[EN] The possibility for a jet of fuel to collide against the surfaces of the combustion chamber or the piston bowl into a thermal engine, has a direct effect on the droplets breakup and the spray atomization. In order to study the spray/wall interaction phenomenon and its influence on the macroscopic spray behavior, a diesel spray was visualized when impinging on a flat wall made of quartz at various ambient, injection and wall position conditions. Two high-speed cameras were employed simultaneously to perform Schlieren imaging and diffuse back illumination diagnostics, in order to observe both spray vapor and liquid phases during their contact with the wall. The experiments were performed in a constant pressure-flow test rig, able to reproduce diesel-like thermodynamic conditions. Two different fuels (n-dodecane and diesel #2) were injected within the chamber by employing a single-hole injector referred to as Spray D into the framework of ECN research group. To place the wall in the spray path, a wall positioning structure capable of being fitted into the chamber and of support the wall at various inclination angles and distances from the injector tip, was designed. The test rig was filled with N2 to keep an inert atmosphere and isolate the spray development from possible alterations produced by combustion. Results provide the influence of the injected fuel, operating and wall conditions on the macroscopic features of the transient spray in terms of spreading onto the wall and spray thickness characterized both temporally and spatially. Spray spreading was evaluated by a novel penetration-based parameter. It showed to be proportional to the square root of time similarly as free-penetration and is largely affected by the wall inclination respect to the spray axis. Spray angle showed to be influenced by the morphology of the spray that affects its air entrainment capacity and that changes with a wall respect to a free-jet configuration. This variation in the morphology also has a remarkable effect on spray evaporation, characterized in terms of liquid length and liquid spreading onto the wall. Finally, the large amount of data was used to obtain correlations for all the studied parameters., This research was funded by the Spanish Ministerio de Ciencias, Investigacion y Universidades through project reference RTI2018-099706-B-I00. Part of the experimental hardware was purchased through funds obtained from Spanish Ministerio de Ciencia, Innovacion y Universidades with FEDER funds through project with reference EQC2018-004605-P. Finally, the support of Omar Huerta Cornejo and Borja Hurtado in the experiments performance and laboratory work is greatly appreciated.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of isotropic and anisotropic turbulent structures over spray atomization in the near field

  • Crialesi-Esposito, Marco
  • González-Montero, Lucas Antonio
  • Salvador, Francisco Javier|||0000-0003-3269-2251
[EN] Sprays and atomization processes are extremely diffused both in nature and in industrial applications. In this paper we analyze the influence of the nozzle turbulence on primary atomization, focusing on the resulting turbulent field and atomization patterns in the Near Field (NF). In order to do so, a Synthetic Boundary Condition (SBC) and a Mapped Boundary Condition (MBC), producing respectively isotropic and anisotropic turbulent fields, have been generated as inflow conditions for the spray Direct Numerical Simulations (DNS). We present a specific methodology to ensure consistency on turbulence intensity and integral lengthscale between the two inflows. The analysis performed on the turbulent field (using one-point statistics and spectrum analysis) reveals a significantly stronger turbulent field generated by the inflow boundary conditions with anisotropic structures. While the increased turbulence field generated in the MBC case results in a higher number of droplets generated, the probability functions of both cases are extremely similar, leading to the non-obvious conclusion that the atomization patterns are only slightly affected by the inflow condition. These considerations are supported by the analysis of droplet size distributions, radial distribution functions, axial and radial distributions, highlighting extremely similar behaviors between the MBC and the SBC cases. Finally, these analyses and their computations are presented in detail, underlining how this type of point-process characterization shows interesting potential in future studies on sprays., This research has been partially funded by Spanish Ministerio de Economia y Competitividad through project RTI2018-099706-B-100, "Estudio de la atomizacion primaria mediante simulaciones DNS.. tecnicas opticas de muy alta resolucion''. Additionally, the authors thankfully acknowledge the computer resources at MareNostrum 4 (Barcelona Supercomputing Center) and their technical support provided by FI-2017-2-0035 and TITAN (Oak Ridge Leadership Computing Facility) in the frame of the project TUR124.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational Study of Urea-Water Solution Sprays for the Analysis of the Injection Process in SCR-like Conditions

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Marco-Gimeno, Javier|||0000-0002-4815-3714
[EN] Exhaust after-treatment devices for NOx reduction have become mandatory for achieving the strict diesel emission standards. The selective catalytic reduction (SCR) method has proven to be efficient in this task. Nonetheless, in order to improve the efficiency of the system, the urea-water solution (UWS) injection process needs to be properly characterized due to the limited geometry of the exhaust line and its flow conditions. In combination with the experimental analysis into the system in a dedicated test rig, computational fluid dynamics studies provide better insights into the physical phenomena. Therefore, the main objective of this investigation is to achieve validated droplet size and velocity distributions in the simulation when compared to experiments. Three different positions along the spray are evaluated for that. The methodology adopted includes an Eulerian-Lagrangian approach to study the UWS spray. The results obtained with it show a proper experimental validation as well as the Sauter mean diameter distribution for the conditions tested. The proposed model accurately reproduces the main spray characteristics for different injection pressures and ambient conditions. Thus, the main conclusions obtained sum up in a good methodology for predicting UWS sprays in SCR-like conditions., This research has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018-099706-B-100. Additionally, the experimental hardware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Understanding the effect of inter-jet spacing on lift-off length and ignition delay

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Carreres, Marcos|||0000-0001-6430-6613
  • Montiel-Prieto, Tomas
[EN] In recent years, injectors with multiple outlet-holes and smaller diameters have been implemented to reduce pollutant emissions during the combustion development. Nevertheless, increasing the number of holes has also decreased the spacing between the jets, which could lead to interactions between sprays affecting their behavior, a phenomenon that has not been defined in detail. In this sense, this study analyzes the influence of inter-jet spacing on the ignition delay and lift-off length for a wide range of boundary conditions. To this end, two multi-hole diesel injectors were manufactured with different distributions of the outlet orifices, which allowed the study of the development of an isolated spray and a spray with an inter-jet spacing of 30 degrees during the same injection event. Additionally, the results were compared to the development of sprays under inter-jet spacing values of 36 degrees and 45 degrees. The results showed that the spray with smaller inter-jet spacing had a slightly larger ignition delay at low chamber temperature and density conditions. Regarding the lift-off length, reducing the inter-jet spacing decreased the lift-off length values, these reductions being more noticeable after a threshold of proximity between sprays was achieved. In particular, the spray with an inter-jet spacing value of 30 degrees had considerably lower lift-off length values than those with an inter-jet spacing of 36 degrees and 45 degrees, which in turn had closer lift-off length values than those obtained with the isolated spray. Finally, a novel empirical correlation was developed for the lift-off length considering the influence of inter-jet spacing, thus contributing to the understanding of the effect of the interaction between sprays in the combustion process., This work has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018-099706-B-100. Tomas Montiel was supported by a research grant from Generalitat Valenciana and the European Social Fund (Reference: ACIF/2018/122).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

ECN Spray D visualization of the spray interaction with a transparent wall under engine-like conditions, Part II: Impinging spray combustion

  • Peraza, Jesús E
  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
[EN] In spite of the ever more comprehensive studies on diesel combustion, there is still an important gap on the fundamental knowledge about the interaction of fuel sprays with the piston and cylinder walls in internal combustion engines. The present research corresponds to the second part of an extensive investigation about the spray/wall impingement process at engine-like conditions and its sensitivity to several operating conditions. A constant pressure-flow test rig, which was filled with air extracted from the environment, was employed to perform the experiments at reactive conditions. A single-hole injector from the Engine Combustion Network, referred to as Spray D was employed and a quartz flat wall was set in front of the nozzle by using a supporting structure attached to the vessel. Parameters varied in this work are injected fuel, ambient density, gas temperature, injection pressure, and wall position in terms of distance from the injector hole and inclination angle. Three cameras were simultaneously used to observe the spray-wall interaction (SWI): Schlieren visualization to record the macroscopic evolution of the spray vapor phase and also to determine the ignition delay, a high-speed camera was placed in the front of the wall to directly observe the natural luminosity of the flame through the transparent wall and, finally an intensified camera was used to determine the lift-off length by observing the chemiluminescence of OH*. An extensive geometrical characterization of the spray geometry evolution was made and different metrics were introduced in this work as it is the case of wall lift-off radius to parametrize the observed formation of a lift-off area onto the wall. Similarly, ignition delay showed to be shortened by the presence of the quartz wall up to 15%due to its nearly isothermal configuration and its improvement on air-fuel mixing., This research was funded by the Spanish Ministerio de Ciencias, Investigacion y Universidades through project reference RTI2018-099 706-B-I00. Part of the experimental hardware was purchased through funds obtained from Spanish Ministerio de Ciencia, Innovacion y Universidades with FEDER funds through project with reference EQC2018-004605-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Spray characteristics and penetration of the human cough, and the effectiveness of masks to prevent its dispersion

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Marco-Gimeno, Javier|||0000-0002-4815-3714
[EN] Air-transmitted pathogens have become of particular interest for the general population during the COVID pandemic. Coughing is one of the most important spreading vector for air transmitted pathogens. To prevent and stop the transmission chain, it is of great importance to understand the characteristics of this phenomenon, assess the distance up to which the virion particles are transported and how effective the available masks are to stop the exhaled air. The Schlieren method stands as a proper non-intrusive methodology to study density variations such as the ones produced by the cough. An intubation dummy was instrumentalized to exhale CO2 at realistic cough flow-rates and ambient conditions. General spray characteristics were obtained for a free cough, while effectiveness of a cloth, surgical and FFP2 masks were assessed by analysing the penetration and the angle of the exhaled fluid into the surrounding air. The differences between the propagation distances with and without mask were quantified. The characteristics of a free cough where firstly assessed, and later, the effectiveness of wearing a mask is shown, a cloth one reduces the cough penetration a 50%, while a surgical and FFP2 one reduces it more than an 75%, to less than 10 cm., This research has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018-099706-B-100. Additionally, the experimental hardware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037. Additionally, the Ph.D. student J.M.-G. has been funded by a grant from the Government of Generalitat Valenciana, Spain with reference ACIF/2020/259 and financial support from The European Union.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical Analysis of GDI Flash Boiling Sprays Using Different Fuels

  • Payri, Raul|||0000-0001-7428-5510
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Abboud, Rami
  • Bautista-Rodríguez, Abián
[EN] Modeling the fuel injection process in modern gasoline direct injection engines plays a principal role in characterizing the in-cylinder mixture formation and subsequent combustion process. Flash boiling, which usually occurs when the fuel is injected into an ambient pressure below the saturation pressure of the liquid, is characterized by fast breakup and evaporation rates but could lead to undesired behaviors such as spray collapse, which significantly effects the mixture preparation. Four mono-component fuels have been used in this study with the aim of achieving various flashing behaviors utilizing the Spray G injector from the Engine Combustion Network (ECN). The numerical framework was based on a Lagrangian approach and was first validated for the baseline G1 condition. The model was compared with experimental vapor and liquid penetrations, axial gas velocity, droplet sizes and spray morphology and was then extended to the flash boiling condition for iso-octane, n-heptane, n-hexane, and n-pentane. A good agreement was achieved for most of the fuels in terms of spray development and shape, although the computed spray morphology of pentane was not able to capture the spray collapse. Overall, the adopted methodology is promising and can be used for engine combustion modeling with conventional and alternative fuels., This research was funded by Ministerio de Ciencia, Innovacion y Universidades grant number RTI2018-099706-B-I00 in the frame of the project Study of Primary Early Atomization using DNS and Optical Ultra-high resolution Techniques (SPREAD OUT). Additionally, the PhD student Rami Abboud has been funded by Ayudas para la formacion de profesorado universitario (FPU) program with reference FPU19/03838.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the Influence of Diesel Spray Injection on the Ignition and Soot Formation in Multiple Injection Strategy

  • Payri, Raul|||0000-0001-7428-5510
  • García-Oliver, José M|||0000-0002-2676-9681
  • Mendoza, Victor
  • Viera, Alberto
[EN] Multiple injection strategies have increased their capabilities along with the evolution of injection system technologies up to the point that nowadays it is possible to inject eight different pulses, permitting to improve the engine performance, and consequently, emissions. The present work was realized for two simplified strategies: a pilot-main and a main-post, in order to analyze the influence of an auxiliary pulse on the main and otherwise, in reactive conditions for two pilot/post quantities and four hydraulic dwell times. The study was carried out by employing two optical techniques: diffused back-illumination with flame bandpass chemiluminescence for measuring soot, represented by soot-maps distribution, and single-pass schlieren for ignition delay (ID). Furthermore, a novel methodology for decoupling the start of combustion (SOC) of the second pulse was developed and successfully validated. From the ignition delay results, it was found for all test points that the pilot injection enhanced conditions, which promote a faster ignition of the main pulse, also at higher chamber temperatures, all conditions presented a separate combustion event for each injection. In emission terms, soot increased in the pilot-main strategies compared to its single injection case, as well as, in conditions that promote faster-premixed combustion., This research has been partially funded by Spanish "Ministerio de Ciencia, Innovacion y Universidades" through project RTI2018-099706-B-100. Additionally, the experimental hardware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Measurements of the mass allocation for multiple injection strategies using the rate of injection and momentum flux signals

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Viera, Alberto
[EN] As legislations set very stringent environmental and fuel economy standards, researchers have pushed into a continuous development in all areas of the diesel engine. The recent evolution of the injection technologies has permitted to modify the fuel-delivery strategies. From what was a single pulse per injection event, modern systems allow to inject up to eight different times precisely per combustion cycle. In such sense, experimental results of the rate of injection and momentum flux could be useful for validation and improvement of computational models. Moreover, accurately quantifying the injected mass per pulse in a fuel-gas interface can provide data with more realistic engine-like conditions. To this end, this research presents measurements of the rate of injection and momentum flux for two simple multiple injection strategies: a pilot-main and a main-post. Boundary conditions included two rail and discharge pressures, two different pilot/post quantities and four dwell times. A new approach was employed to estimate the mass allocation with the momentum flux data, and results were compared to the rate of injection traces to verify the distribution calculated. On the results, signals for each pulse were successfully decoupled using its rising and falling edge. The shot-to-shot variability of the pilot/post injection was highly dependent on its transitory characteristics, and on the dwell time for post injections due to internal pressure waves. The injected mass per pulse was successfully measured as well in the momentum flux test rig, and the energizing time changed slightly to account for the different operation interfaces. Signals from both measurement campaigns showed a remarkable agreement when compared, ascertain the possibility of measuring the injected mass, and its allocation for multiple injection strategies, in the momentum flux test rig., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This research was partially funded by the Spanish Ministerio de Ciencias, Investigacion y Universidades through project RTI2018-099706-B-I00. Part of the experimental hardware was purchased through funds obtained from Generalitat Valenciana and FEDER through project IDIFEDER/2018/037. In addition, A.V. was supported through the FPI contract 2016-S2-1361 of "`Programa de Apoyo para la Investigacion y Desarrollo (PAID)'' of Universitat Poltecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental investigation of the lift-offheight and soot formation of a spray flame for different co-flow conditions and fuels

  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Carreres, Marcos|||0000-0001-6430-6613
  • Cardona-Vargas, Santiago
[EN] Since the combustion process in spray flames is a highly complex multi-phase phenomenon, which involves several simultaneous processes such as atomization, vaporization, and chemical kinetics, it is still not fully understood. In the present work, an experimental investigation has been performed for three different hydrocarbon fuels (n-Heptane, n-Decane, n-Dodecane), in order to understand the effect of varying co-flow conditions, fuel mass flow rate, and fuel type on both the flame lift-off height and soot formation. The fuels were injected through a hollow-cone spray injector, with a nominal spray cone angle of 80 degrees and orifice diameter of 120 mu m in an annular non-swirled preheated air co-flow. The flame lift-off height was determined by recording the OH * chemiluminescence, whereas soot formation has been determined through the color diffused back-illumination extinction technique. From the results, it has been observed for a certain fuel that the flame lift-off height is mainly controlled by the co-flow velocity and air co-flow temperature. The results also show that the fuel that yields largest droplet size and that possesses the lowest volatility exhibits the highest flame lift-off height. Furthermore, the results evidence a strong influence of the co-flow velocity on the soot formation. With an increase in co-flow velocity, the flame lift-off height is increased and so the amount of air entrainment, leading to a less rich reaction zone just downstream of the lift-off height, which in turn results in less soot formation. Finally, the comparison among different fuels shows that their differences in soot formation are likely related to fuel sooting tendency. This property, in turn, depends on the fuel molecular structure playing an important role on its determination., This research was funded bythe Spanish Ministerio de Ciencias, Investigacion y Universidades through project RTI2018-099706-BI00. Part of the experimental hardware was purchased through funds obtained from Spanish Ministerio de Ciencias, Investigacion y Universidades and FEDER through project EQC2019-005818-P. The author Santiago Cardona Vargas would like to thank Universitat Politecnica de Valencia for his Predoctoral contract (FPI-2016-S1), which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-2016). The authors are thankful to Jose Enrique Del Rey and Omar Huerta for helping in the technical issues, also to Carlos Gil Martinez for helping during the experimental campaign.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Mixture Model Approach for the Study of the Inner Flow Dynamics of an AdBlue Dosing System and the Characterization of the Near-Field Spray

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Marco-Gimeno, Javier|||0000-0002-4815-3714
[EN] Selective Catalytic Reduction stands for an effective methodology for the reduction of NOx emissions from Diesel engines and meeting current and future EURO standards. For it, the injection of Urea Water Solution (UWS) plays a major role in the process of reducing the NOx emissions. A LES approach for turbulence modelling allows to have a description of the physics which is a very useful tool in situations where experiments cannot be performed. The main objective of this study is to predict characteristics of the flow of interest inside the injector as well as spray morphology in the near field of the spray. For it, the nozzle geometry has been reconstructed from X-Ray tomography data, and an Eulerian-Eulerian approach commonly known as Mixture Model has been applied to study the liquid phase of the UWS with a LES approach for turbulence modeling. The injector unit is subjected to typical low-pressure working conditions. The results extracted from it comprise parameters that characterize the hydraulic behavior as well as jet intact length. The conclusions drawn from the model depict differences in the flow behavior between the injector three orifices, with an under-prediction of nozzle and spray characteristics of LES formulation with respect to traditional RANS turbulence treatment., The presented work is funded by a grant of Generalitat Valenciana, with reference ACIF/2020/259 and of the European Union. Partial funding comes as well from Spanish Ministerio de Ciencia, Innovación y Universidades through project RTI2018-099706-B-100. Additionally, the experimental hard-ware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Scaling spray penetration at supersonic conditions through shockwave analysis

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Taghavifar, Hadi
  • Nemati, Arash
[EN] In the current paper, an investigation of the supersonic flow effect on shockwave generation and diesel spray penetration scaling has been performed. For this purpose, spray visualization tests have been carried out in a constant-pressure chamber at room temperature using shadowgraphy technique. Two working gases have been used: nitrogen, with similar thermodynamic characteristics to the engine environment, and sulfur hexafluoride, aimed at producing supersonic conditions at moderate injection pressure values. A total of 60 operating points, including different nozzle geometries, injection pressures and chamber densities have been studied. From the visualization study, two different kinds of shockwaves have been detected: normal or frontal, for moderate spray tip Mach (between 1 and 1.5); and oblique, when the Mach is higher than 1.5. The penetration results show that, for the same injection conditions in terms of injection pressure and chamber density, the spray propagation is equal for SF6 and N-2 when the spray is on subsonic conditions, while penetration is higher for SF6 when supersonic velocity is reached. This behavior has been related to the density gradient appearing across the shockwave. A new methodology to extrapolate supersonic penetration from the well-known subsonic penetration law has been proposed, showing good agreement with the experimental results., This work was partly sponsored by "Ministerio de Ciencia, Innovacion y Universidades", of the Spanish Government, in the frame of the Project "Estudio de la atomizacion primaria mediante simulaciones DNS y tecnicas opticas de muy alta resolucion", Reference RTI2018-099706-B-I00.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis de maestría (MasterThesis)

Estudio computacional con modelos Lagrangianos de las características macroscópicas y microscópicas de chorros líquidos de Urea-Agua para la reducción de NOx

  • Marco-Gimeno, Javier|||0000-0002-4815-3714
The presented work is funded by a grant of Generalitat Valenciana, with reference ACIF/2020/259 and of the European Union. Partial funding comes as well from Spanish Ministerio de Ciencia, Innovación y Universidades through project RTI2018-099706-B-100. Additionally, the experimental hardware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Using momentum flux measurements to determine the injection rate of a commercial Urea Water Solution injector

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Moreno-Gasparotto, Armando Enrique
[EN] The Selective Catalytic Reduction (SCR) technology allows the transformation of the Nitrous Oxide emissions present in exhaust gases into gaseous nitrogen and water. For a proper operation of the SCR, a urea-water solution (UWS) injector must dose an adequate amount of liquid into the exhaust pipe in order to avoid deposit formation and to guarantee the SCR system efficiency. This task requires the knowledge of the performance of the injector. Then, the goal of this work is to study the hydraulic performance of a UWS injector, by means of measuring the spray momentum flux in order to understand the influence of different variables as injected fluid, injection pressure, counter pressure and cooling temperature of the injector on the flow characteristics. The tested injector was cooled at three different temperatures, 60, 90 and 120 degrees C, the injection pressure of the UWS was set at 5, 7 and 9 bar, with counter pressures of 750, 900, 1000 and 2000 mbar for the two tested fluids, water and UWS. The measurements were carried out using an experimental facility developed at CMT-Motores Termicos for the determination of spray momentum flux, where a piezoelectric pressure sensor was located near the nozzle exit of the injector, which measures the impact force of the spray. Additionally, the proposed methodology allowed to determine the injected mass flow and to capture the transient injection events, such as the opening and closing stages. Moreover, mass flow rate measurements of the injector were performed under the same operating conditions, determining the influence of the injection pressure, cooling temperature, counter pressure and fluid properties. Regarding the pressure, the tendency was as expected, the higher the injection pressure the higher the Momentum flux and flow rate. Results showed that an increment of the cooling temperature of the injector induces the appearance of flash boiling conditions, having an impact on the total injected mass and momentum flux, changing the behaviour of the spray. For the same conditions, water has a higher momentum flux than the UWS due to differences in fluid properties and velocity at the nozzle exit., This work has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018099706B100. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI2018S213) , which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of evaporative diesel spray interaction in multiple injections using optical diagnostics

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Abboud, Rami
  • Viera, Alberto
[EN] Internal combustion engines have witnessed an ever increasing stringency in emission limits and fuel economy regulations that has continuously provoked researchers to develop complex strategies that enables engines to cope with these standards. Optical techniques have been a viable method in the study of thermal processes occurring inside internal combustion engines and provides researchers with a solid understanding of the heat and mass transfer taking place. In particular, the current study utilizes two optical techniques, diffused back illumination and schlieren imaging, to visualize the spray behavior in multiple injection strategies of evaporative diesel sprays. A novel method has been developed in order to couple the two optical techniques to visualize both liquid and vapor phases of either pilot-main and main-post injections. The influence of the auxiliary injections on the main, and vice versa, in terms of spray segmentation and spray development has been studied for two different pilot/post quantities and four hydraulic dwell times under two different chamber conditions. The spray development displayed no effect of pilot quantity and dwell time on the liquid length of the second injection. On the other hand, a more pronoun effect on the vapor phase penetration and spreading angle was evidenced by the pilot injection where the main injection has penetrated farther with a higher spreading angle as compared to the case with a single injection event. The understanding of multiple injection is thus fundamental for the improvement of thermal processes in Internal Combustion Engines., This research has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018-099706B-100. Additionally, the experimental hardware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of turbulence in atomizing liquid jets

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Crialesi-Esposito, Marco
[EN] Among the many unknowns in the study of atomizing sprays, defining an unambiguous way to analyze turbulence is, perhaps, one of the most limiting ones. The lack of proper tools for the analysis of the turbulence field (e.g. specific one/two-point statistics, spectrum, structure functions) limits the understanding of the overall phenomenon occurring, impeding the correct estimation of motion scales (from the Kolmogorov one to the integral one). The present work proposes a methodology to analyze the turbulence in atomizing jets using a pseudo-fluid method. The many challenges presented in these types of flows (such as temporal fluid properties uncertainties, strong anisotropy and lack of a priori chance of determining the motion scales) can be simplified by such a method, as it will be clearly shown by the smooth results obtained. Finally, the method is tested against the one-phase flows turbulent data available in the literature for the Kolmogorov scaling of the one-dimension energy spectra, showing how a pseudo-fluid method could provide a reliable tool to analyze multiphase turbulence, especially in spray's primary atomization., This research has been partially funded by Spanish Ministerio de Economia y Competitividad through project RTI2018-099706-B-100, "Estudio de la atomizacion primaria mediante simulaciones DNS y tecnicas opticas de muy alta resolucion". Additionally, the authors thankfully acknowledge the computer resources at MareNostrum 4 (Barcelona Supercomputing Center) and their technical support provided by FI-2017-2-0035 and TITAN (Oak Ridge Leadership Computing Facility) in the frame of the project TUR124.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis de maestría (MasterThesis)

Diesel Spray Interaction in Multiple Injection Strategies under Evaporative Conditions, Estudio de la interacción del chorro diesel en estrategias de inyección múltiple bajo condiciones evaporativas

  • Abboud, Rami
[ES] Los motores de combustión interna han sido testigos de un endurecimiento cada vez mayor de los límites en las emisiones y de las normativas de ahorro de combustible, lo que ha provocado que investigadores de todo el mundo desarrollen complejas estrategias que permitan a los motores hacer frente a estas exigencias. Las técnicas ópticas han sido, durante años, un método viable en el estudio de procesos térmicos que tienen lugar en el interior de los motores de combustión interna, proporcionando así a los investigadores una amplia comprensión de la trasferencia de masa y calor que tiene lugar en el mencionado proceso. En concreto, los estudios llevados a cabo en la presente investigación se han desarrollado utilizando dos técnicas ópticas diferentes, diffused back illumination y schlieren, con el objetivo de visualizar el comportamiento del chorro diesel en estrategias de inyección múltiples bajo condiciones evaporativas. Se ha desarrollado un novedoso método con el fin de acoplar las dos técnicas ópticas para visualizar tanto la fase líquida como la de vapor de ambas estrategias de inyección: piloto-principal y principal-post. Se ha analizado la influencia de la inyección auxiliar en la principal y viceversa en términos de atomización y desarrollo del chorro para dos configuraciones diferentes de piloto/post y cuatro tiempos hidráulicos de separación entre inyecciones (dwell time) bajo dos condiciones de operación distintas. La penetración de líquido de la segunda inyección no se vio afectada por la variación de las características de la inyección piloto y del dwell time. Por otro lado, se evidenció un efecto más pronunciado de la inyección piloto sobre la principal en la penetración de la fase de vapor y el ángulo del chorro. Una mayor penetración y un mayor ángulo en la inyección principal fueron obtenidos en comparación con una inyección simple. Por estos motivos, el entendimiento de la inyección múltiple es fundamental para la mejora de los procesos térmicos en los motores de combustión interna., [EN] Internal combustion engines have witnessed an ever increasing stringency in emission limits and fuel economy regulations that has continuously provoked researchers to develop complex strategies that enables engines to cope with these standards. Optical techniques have been a viable method in the study of thermal processes occurring inside internal combustion engines and provides researchers with a solid understanding of the heat and mass transfer taking place. In particular, the current study utilizes two optical techniques, diffused back illumination and schlieren imaging, to visualize the spray behavior in multiple injection strategies of evaporative diesel sprays. A novel method has been developed in order to couple the two optical techniques to visualize both liquid and vapor phases of either pilot-main and main-post injections. The influence of the auxiliary injections on the main, and vice versa, in terms of spray segmentation and spray development has been studied for two different pilot/post quantities and four hydraulic dwell times under two different chamber conditions. The spray development displayed no effect of pilot quantity and dwell time on the liquid length of the second injection. On the other hand, a more pronoun effect on the vapor phase penetration and spreading angle was evidenced by the pilot injection where the main injection has penetrated farther with a higher spreading angle as compared to the case with a single injection event. The understanding of multiple injection is thus fundamental for the improvement of thermal processes in Internal Combustion Engines., This research has been partially funded by Spanish Ministerio de Ciencia, Innovación y Universidades through project RTI2018-099706-B-100. Additionally, the experimental hardware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of vortex core generation in pipe flows under different reynolds number conditions

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • Quintero-Igeño, Pedro-Manuel|||0000-0003-4373-2079
  • González-Montero, Lucas Antonio
[EN] Pipe flow is a well-documented case widely studied in both theoretical and practical applications. The present work aims at studying the influence of the Reynolds number on turbulent vortex distribution using Large Eddy Simulations (LES). Features such as the mean velocity profiles and root mean squared velocity are first numerically investigated for different fluid properties involving Reynolds numbers ranging from 5,925 to 15,190 in order to verify the law-of-the-wall and turbulence statistics with experimental and DNS data. Once the simulations are validated, the vortex core generation within the flow is studied through a detection algorithm based on the lambda 2 criterion with two different approaches, first using an absolute threshold value and then using a relative threshold value depending on the turbulent intensity. Results are compared in terms of number of structures and Probability Density Functions for both the size and the radial distributions. Finally, results are compared for one condition with the Q-criterion to assess the results obtained resulting in practically identical volume and radial distributions. These results are deemed to shed light on the vortex formation and location to generate proper inflow boundary conditions to highly resolved simulations in varied engineering applications., This research has been funded by the Spanish Ministerio de Economia y Competitividad through the project RTI2018099706-B-100: "Estudio de la atomizacion primaria mediante simulaciones DNS y tecnicas opticas de muy alta resolucion" and the Spanish Ministerio de Ciencia e innovacion through the project EQC2018004605-P: "Estudio del proceso de inyeccion en atmosferas presurizadas". The authors thankfully acknowledge the computer resources from the Rigel cluster at UPV (Spain) and the Bebop cluster from the Laboratory Computing Resource Center at Argonne National Laboratory (USA). L.A. Gonzalez-Montero is partially supported through the contract FPI -Subprograma 2 of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of aging of a diesel injector on multiple injection strategies

  • Payri, Raul|||0000-0001-7428-5510
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Montiel-Prieto, Tomas
  • Viera, Alberto
[EN] Multiple injection strategies have contributed to the improvement of thermal processes in Internal Combustion Engines. On this matter, the correct performance of the injector is a critical factor in the implementation of these techniques, as changes in the behavior of the injector could affect the injection development, altering the combustion process and heat transformation efficiency. Thus, the present study analyzes the development of multiple injection events in a diesel injector aged due to partial obstruction of the holes of the nozzle. To this end, a multi-hole piezoelectric injector was employed, in which the aging of the injector is evaluated through momentum flux measurements for each hole. Afterwards, rate of injection tests with pilot and post injection strategies are performed, and the results are compared to the injection events made by the same injector before aging. The results provided by the momentum flux experiments confirmed the partial obstruction of two holes. Furthermore, rate of injection comparisons showed that the injector had a lower steady-state rate of injection after aging and required a longer time to end the injection. These phenomena affected the multiple injection events, as the extended time required to end the injection reduced the hydraulic dwell time between pilot/post injection and the main injection. Furthermore, for short dwell times, this phenomenon led to the unification of the main and post injection, resulting in a large single injection. Hence, not only an increase in fuel consumption would appear, but the thermal benefits of implementing the post injection would be lost., This work has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018-099706B-100. Tomas Montiel was supported by a research grant from Generalitat Valenciana and the European Union (Reference: ACIF/2018/122).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical Analysis of Urea to Ammonia Conversion in Automotive Selective Catalytic Reduction Realistic Conditions

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Marco-Gimeno, Javier|||0000-0002-4815-3714
[EN] The selective catalytic reduction (SCR) is a technology employed for NOx reduction purposes which is based on the injection of an Urea Water Solution (UWS) into the exhaust line. Conversion of this injected urea into ammonia is a key step to ensure high SCR efficiency. In order to study this phenomenon, a three-dimensional model of the urea-water injection process has been created to recreate realistic conditions. A Lagrangian-Eulerian approach has been followed to model liquid and gas phases, respectively. Droplet evaporation as well as relevant chemical processes have been included to recreate the thermolysis and hydrolysis phenomena, and the results have been validated against literature data. Then, the validated model has been applied to recreate an in-house experimental facility that measured spray macroscopic and microscopic characteristics by means of diffused back illumination (DBI) visualization. Probability density functions of the UWS droplet sizes as well as the velocity distributions have been obtained at three different regions of interest to be compared with the experimental data set. Contours of isocyanic acid and ammonia mass fractions have been included to show the chemical transformation from urea into its products. The model accurately replicates the experimental results, and it stands as a good methodology to predict the main spray characteristics as well as the chemical processes that take place in actual SCR systems., This research has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018099706-B-100. Additionally, the experimental hardware was purchased through FEDER and Generalitat Valenciana under project IDIFEDER/2018/037. Additionally, the Ph.D. student J.M.-G. has been funded by a grant from the Government of Generalitat Valenciana with reference ACIF/2020/259 and financial support from The European Union.