Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of the influence of the fuel and boundary conditions over the soot formation in multi-hole diesel injectors using high-speed color diffused back-illumination technique

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Cardona-Vargas, Santiago
  • Ayyapureddi, Sridhar
[EN] Two prototypes multi-hole diesel injector from a high-pressure common rail system were used to operated with diesel and n-Heptane fuels in a high-pressure and high-temperature test rig able to reach 1100 K and 15 MPa under different oxygen concentrations with the goal to study the influence of the boundary conditions on the combustion process evaluating parameters as ignition delay, lift-off length and soot formation. A novel optical set-up was implemented to visualize the soot cloud evolution in the fuel jet between 30 and 85 nun from the nozzle exit using the high-speed color diffused back-illumination technique, it was used as a result of the insertion of a high-pressure window in the injector holder opposite to the frontal window of the vessel allowing an optical arrangement in line-of-sight. The experiments performed in this work used a LED with a wavelength of 460 nm to provide information about physical of the soot properties, the results of varying the operational conditions show the reduction of soot formation with an increase in injection pressure, a reduction in ambient temperature, a reduction in oxygen concentration or a reduction in ambient density. Furthermore, fuel effect on soot formation also has been studied showing a big difference between both fuels, diesel is known to be more prone to produce soot than n-Heptane reducing the ability of the technique implemented, especially in conditions with high temperature and high density., This research has been funded by Jaguar Land Rover. The author Santiago Cardona thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2016-S1), which is included within the framework of Programa de Apoyo para la InvestigaciOn y Desarrollo (PAID -01-2016). We would like to thank Omar Huerta for his collaboration during the measurement campaign and laboratory work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental investigation of the lift-offheight and soot formation of a spray flame for different co-flow conditions and fuels

  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Carreres, Marcos|||0000-0001-6430-6613
  • Cardona-Vargas, Santiago
[EN] Since the combustion process in spray flames is a highly complex multi-phase phenomenon, which involves several simultaneous processes such as atomization, vaporization, and chemical kinetics, it is still not fully understood. In the present work, an experimental investigation has been performed for three different hydrocarbon fuels (n-Heptane, n-Decane, n-Dodecane), in order to understand the effect of varying co-flow conditions, fuel mass flow rate, and fuel type on both the flame lift-off height and soot formation. The fuels were injected through a hollow-cone spray injector, with a nominal spray cone angle of 80 degrees and orifice diameter of 120 mu m in an annular non-swirled preheated air co-flow. The flame lift-off height was determined by recording the OH * chemiluminescence, whereas soot formation has been determined through the color diffused back-illumination extinction technique. From the results, it has been observed for a certain fuel that the flame lift-off height is mainly controlled by the co-flow velocity and air co-flow temperature. The results also show that the fuel that yields largest droplet size and that possesses the lowest volatility exhibits the highest flame lift-off height. Furthermore, the results evidence a strong influence of the co-flow velocity on the soot formation. With an increase in co-flow velocity, the flame lift-off height is increased and so the amount of air entrainment, leading to a less rich reaction zone just downstream of the lift-off height, which in turn results in less soot formation. Finally, the comparison among different fuels shows that their differences in soot formation are likely related to fuel sooting tendency. This property, in turn, depends on the fuel molecular structure playing an important role on its determination., This research was funded bythe Spanish Ministerio de Ciencias, Investigacion y Universidades through project RTI2018-099706-BI00. Part of the experimental hardware was purchased through funds obtained from Spanish Ministerio de Ciencias, Investigacion y Universidades and FEDER through project EQC2019-005818-P. The author Santiago Cardona Vargas would like to thank Universitat Politecnica de Valencia for his Predoctoral contract (FPI-2016-S1), which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-2016). The authors are thankful to Jose Enrique Del Rey and Omar Huerta for helping in the technical issues, also to Carlos Gil Martinez for helping during the experimental campaign.