Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

ECN Spray D visualization of the spray interaction with a transparent wall under engine-like conditions. Part I: Non-reactive impinging spray

  • Peraza, Jesús E.
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Ruiz-Rosales, Santiago|||0000-0001-9536-3696
[EN] The possibility for a jet of fuel to collide against the surfaces of the combustion chamber or the piston bowl into a thermal engine, has a direct effect on the droplets breakup and the spray atomization. In order to study the spray/wall interaction phenomenon and its influence on the macroscopic spray behavior, a diesel spray was visualized when impinging on a flat wall made of quartz at various ambient, injection and wall position conditions. Two high-speed cameras were employed simultaneously to perform Schlieren imaging and diffuse back illumination diagnostics, in order to observe both spray vapor and liquid phases during their contact with the wall. The experiments were performed in a constant pressure-flow test rig, able to reproduce diesel-like thermodynamic conditions. Two different fuels (n-dodecane and diesel #2) were injected within the chamber by employing a single-hole injector referred to as Spray D into the framework of ECN research group. To place the wall in the spray path, a wall positioning structure capable of being fitted into the chamber and of support the wall at various inclination angles and distances from the injector tip, was designed. The test rig was filled with N2 to keep an inert atmosphere and isolate the spray development from possible alterations produced by combustion. Results provide the influence of the injected fuel, operating and wall conditions on the macroscopic features of the transient spray in terms of spreading onto the wall and spray thickness characterized both temporally and spatially. Spray spreading was evaluated by a novel penetration-based parameter. It showed to be proportional to the square root of time similarly as free-penetration and is largely affected by the wall inclination respect to the spray axis. Spray angle showed to be influenced by the morphology of the spray that affects its air entrainment capacity and that changes with a wall respect to a free-jet configuration. This variation in the morphology also has a remarkable effect on spray evaporation, characterized in terms of liquid length and liquid spreading onto the wall. Finally, the large amount of data was used to obtain correlations for all the studied parameters., This research was funded by the Spanish Ministerio de Ciencias, Investigacion y Universidades through project reference RTI2018-099706-B-I00. Part of the experimental hardware was purchased through funds obtained from Spanish Ministerio de Ciencia, Innovacion y Universidades with FEDER funds through project with reference EQC2018-004605-P. Finally, the support of Omar Huerta Cornejo and Borja Hurtado in the experiments performance and laboratory work is greatly appreciated.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

ECN Spray D visualization of the spray interaction with a transparent wall under engine-like conditions, Part II: Impinging spray combustion

  • Peraza, Jesús E
  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
[EN] In spite of the ever more comprehensive studies on diesel combustion, there is still an important gap on the fundamental knowledge about the interaction of fuel sprays with the piston and cylinder walls in internal combustion engines. The present research corresponds to the second part of an extensive investigation about the spray/wall impingement process at engine-like conditions and its sensitivity to several operating conditions. A constant pressure-flow test rig, which was filled with air extracted from the environment, was employed to perform the experiments at reactive conditions. A single-hole injector from the Engine Combustion Network, referred to as Spray D was employed and a quartz flat wall was set in front of the nozzle by using a supporting structure attached to the vessel. Parameters varied in this work are injected fuel, ambient density, gas temperature, injection pressure, and wall position in terms of distance from the injector hole and inclination angle. Three cameras were simultaneously used to observe the spray-wall interaction (SWI): Schlieren visualization to record the macroscopic evolution of the spray vapor phase and also to determine the ignition delay, a high-speed camera was placed in the front of the wall to directly observe the natural luminosity of the flame through the transparent wall and, finally an intensified camera was used to determine the lift-off length by observing the chemiluminescence of OH*. An extensive geometrical characterization of the spray geometry evolution was made and different metrics were introduced in this work as it is the case of wall lift-off radius to parametrize the observed formation of a lift-off area onto the wall. Similarly, ignition delay showed to be shortened by the presence of the quartz wall up to 15%due to its nearly isothermal configuration and its improvement on air-fuel mixing., This research was funded by the Spanish Ministerio de Ciencias, Investigacion y Universidades through project reference RTI2018-099 706-B-I00. Part of the experimental hardware was purchased through funds obtained from Spanish Ministerio de Ciencia, Innovacion y Universidades with FEDER funds through project with reference EQC2018-004605-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of vortex core generation in pipe flows under different reynolds number conditions

  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • Quintero-Igeño, Pedro-Manuel|||0000-0003-4373-2079
  • González-Montero, Lucas Antonio
[EN] Pipe flow is a well-documented case widely studied in both theoretical and practical applications. The present work aims at studying the influence of the Reynolds number on turbulent vortex distribution using Large Eddy Simulations (LES). Features such as the mean velocity profiles and root mean squared velocity are first numerically investigated for different fluid properties involving Reynolds numbers ranging from 5,925 to 15,190 in order to verify the law-of-the-wall and turbulence statistics with experimental and DNS data. Once the simulations are validated, the vortex core generation within the flow is studied through a detection algorithm based on the lambda 2 criterion with two different approaches, first using an absolute threshold value and then using a relative threshold value depending on the turbulent intensity. Results are compared in terms of number of structures and Probability Density Functions for both the size and the radial distributions. Finally, results are compared for one condition with the Q-criterion to assess the results obtained resulting in practically identical volume and radial distributions. These results are deemed to shed light on the vortex formation and location to generate proper inflow boundary conditions to highly resolved simulations in varied engineering applications., This research has been funded by the Spanish Ministerio de Economia y Competitividad through the project RTI2018099706-B-100: "Estudio de la atomizacion primaria mediante simulaciones DNS y tecnicas opticas de muy alta resolucion" and the Spanish Ministerio de Ciencia e innovacion through the project EQC2018004605-P: "Estudio del proceso de inyeccion en atmosferas presurizadas". The authors thankfully acknowledge the computer resources from the Rigel cluster at UPV (Spain) and the Bebop cluster from the Laboratory Computing Resource Center at Argonne National Laboratory (USA). L.A. Gonzalez-Montero is partially supported through the contract FPI -Subprograma 2 of the Universitat Politecnica de Valencia.