Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of Fiber Bragg Grating Sensors for Monitoring Shaft Vibrations of Hydraulic Turbines

  • Sánchez-Botello, Xavier
  • Roig, Rafael
  • De La Torre, Oscar
  • Escaler, Xavier
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] The structural dynamic response of hydraulic turbines needs to be continuously monitored to predict incipient failures and avoid catastrophic breakdowns. Current methods based on traditional off-board vibration sensors mounted on fixed components do not permit inferring loads induced on rotating parts with enough accuracy. Therefore, the present paper assesses the performance of fiber Bragg grating sensors to measure the vibrations induced on a rotating shaft¿disc assembly partially submerged in water resembling a hydraulic turbine rotor. An innovative mounting procedure for installing the sensors is developed and tested, which consists of machining a thin groove along a shaft line to embed a fiber-optic array that can pass through the bearings. At the top of the shaft, a rotary joint is used to extract, in real time, the signals to the interrogator. The shaft strain distribution is measured with high spatial resolution at different rotating speeds in air and water. From this, the natural frequencies, damping ratios, and their associated mode shapes are quantified at different operating conditions. Additionally, the change induced in the modes of vibration by the rotation effects is well captured. All in all, these results validate the suitability of this new fiber-optic technology for such applications and its overall better performance in terms of sensitivity and spatial resolution relative to traditional equipment. The next steps will consist of testing this new sensing technology in actual full-scale hydraulic turbines., This work was supported by the funding received from the European Union s Horizon H2020 research and innovation program (grant agreement no: 814958) and by the I+D+i project SYNERGY PID2020-118310RBI00 funded by the MCIN/AEI/10.13039/501100011033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of Fiber Bragg Grating sensors for monitoring induced strains on the draft tube cone of hydraulic turbines

  • Sánchez-Botello, X.
  • Roig, R.
  • de la Torre, O.
  • Mulu, B.
  • Högström, C-M.
  • Escaler, X.
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] In hydraulic turbines, several flow instabilities can take place inside the draft tube cone during off-design and transient operating conditions such as the rotating vortex rope which can severely damage the structure if sustained in time. In the frame of the AFC4Hydro H2020 research project, an extensive measurement campaign has been carried out to monitor and predict this rotating vortex rope phenomenon in a reduced scale Kaplan turbine model at the Vattenfall Research and Development facility in Älvkarleby, Sweden. The hydraulic turbine model has been operated in propeller mode with a fixed blade angle corresponding to its best efficiency point. Several sensors have been placed along the test stand to monitor vibrations, strains and pressures. Concretely, the present paper assesses the performance of using Fiber Bragg Grating sensors to measure the strains induced on the draft tube cone walls with high-spatial resolution in three different zones of influence: the upper and lower flanges and the vertical cone wall between the runner outlet and the elbow. To do so, a total of 3 arrays embedding a total of 48 Fiber Bragg Grating sensors were glued inside three grooves previously machined on these particular areas of the draft tube cone. Analysing the frequency response of the different Fiber Bragg Grating sensors, the strain patterns induced by the rotating and plunging components of the rotating vortex rope have been precisely determined. Moreover, their impacts at the different part load conditions tested have also been quantified., This work was supported by the funding received from the European Union s Horizon H2020 research and innovation program under grant agreement No 814958. The authors would like to acknowledge the technical support received from Vattenfall AB.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fiber Bragg Grating Sensors for Underwater Vibration Measurement: Potential Hydropower Applications

  • de la Torre, Oscar
  • Floris, Ignazio
  • Escaler, Xavier
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] The present paper assesses the performance and characteristics of fiber Bragg grating sensors, with a special interest in their applications in hydraulic machinery and systems. The hydropower industry is turning to this technology with high expectations of obtaining high quality data to validate and calibrate numerical models that could be used as digital twins of key assets, further strengthening the sector's relevant position within industry 4.0. Prior to any validation, fiber Bragg grating sensors' ability to perform well underwater for long periods of time with minimal degradation, and their ease of scalability, drew the authors ' attention. A simplified modal analysis of a partially submerged beam is proposed here as a first step to validate the potential of this type of technology for hydropower applications. Fiber Bragg grating sensors are used to obtain the beam's natural frequencies and to damp vibrations under different conditions. The results are compared with more established waterproof electric strain gauges and a laser vibrometer with good agreement. The presence of several sensors in a single fiber ensures high spatial resolution, fundamental to precisely determine vibration patterns, which is a main concern in this industry. In this work, the beam's vibration patterns have been successfully captured under different excitations and conditions., This research was funded by Horizon 2020 research and innovation program under grant agreement No 814958.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modeling and Adaptive Parameter Estimation for a Piezoelectric Cantilever Beam

  • Wang, Bin
  • Costa Castelló, Ramon
  • Na, Jing
  • Torre, Óscar de la
  • Escaler Puigoriol, Xavier
This paper proposes a new adaptive estimation approach to online estimate the model parameters of a piezoelectric cantilever beam. The beam behavior is firstly modeled using partial differential equations (PDE) considering the Kelvin-Voigt damping. To facilitate the estimation of unknown model parameters, the Galerkin's method is introduced to extract desired vibration modes by separating the time and space variables of the PDE. Then, considering two major vibration modes, the corresponding system model can be represented by a fourth-order ordinary differential equation (ODE). Finally, by using measured input and output information, a novel adaptive parameter estimation strategy is introduced to estimate the unknown parameters of the derived ODE model in real time. For the purpose of driving the parameter updating law, the estimation error is extracted by using an auxiliary variable and a time-varying gain. Consequently, the convergence of the parameter estimation error is rigorously proved based on the Lyapunov theory. Simulations and experimental results show the validity and practicability of the proposed estimation method., European Union’s Horizon 2020 Research and Inovation Program (Grant Number: 814958) 10.13039/501100001809-National Natural Science Foundation of China (Grant Number: 62273169, 61922037 and 61873115) Yunnan Fundamental Research Project (Grant Number: 202001AV070001) Project DOVELAR (Grant Number: RTI2018-096001-B-C32) 10.13039/501100004543-Chinese Scholarship Council (Grant Number: 201908530215)
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Assessment of fiber Bragg grating sensors for monitoring shaft vibrations of hydraulic turbines

  • Sánchez Botello, Xavier
  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Madrigal, Javier
  • Sales, Salvador
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The structural dynamic response of hydraulic turbines needs to be continuously monitored to predict incipient failures and avoid catastrophic breakdowns. Current methods based on traditional off-board vibration sensors mounted on fixed components do not permit inferring loads induced on rotating parts with enough accuracy. Therefore, the present paper assesses the performance of fiber Bragg grating sensors to measure the vibrations induced on a rotating shaft–disc assembly partially submerged in water resembling a hydraulic turbine rotor. An innovative mounting procedure for installing the sensors is developed and tested, which consists of machining a thin groove along a shaft line to embed a fiber-optic array that can pass through the bearings. At the top of the shaft, a rotary joint is used to extract, in real time, the signals to the interrogator. The shaft strain distribution is measured with high spatial resolution at different rotating speeds in air and water. From this, the natural frequencies, damping ratios, and their associated mode shapes are quantified at different operating conditions. Additionally, the change induced in the modes of vibration by the rotation effects is well captured. All in all, these results validate the suitability of this new fiber-optic technology for such applications and its overall better performance in terms of sensitivity and spatial resolution relative to traditional equipment. The next steps will consist of testing this new sensing technology in actual full-scale hydraulic turbines., This work was supported by the funding received from the European Union’s Horizon H2020 research and innovation program (grant agreement no: 814958) and by the I+D+i project SYNERGY PID2020-118310RBI00 funded by the MCIN/AEI/10.13039/501100011033., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the rotating vortex rope and its induced structural response in a Kaplan turbine model

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
  • Mulu, Berhanu
  • Högström, Carl-Maikel
The rotating vortex rope, which can be decomposed in the rotating and the plunging modes, is the origin of pressure fluctuations in the draft tube cone when hydraulic turbines operate at part load, compromising the structural integrity and limiting the output load. A measurement campaign was carried out in a Kaplan turbine model which is a replica of the experimental 10 MW Porjus U9 prototype machine along a propeller curve to study the rotating vortex rope’s excitation levels and the induced structural responses. A complete set of sensors mounted on-board and off-board was used to measure pressures, forces, torques, accelerations, displacements, and strains. The characteristic frequencies and amplitudes of the pressure fluctuations and of the corresponding induced loads and vibrations associated with the two modes were quantified in a wide range of operating conditions at part load. The two modes are detected at different frequencies depending on the sensor position. Moreover, their frequencies change depending on the discharge and present different amplitudes depending on the mode. Particularly, the rotating mode shows higher amplitudes than the plunging mode in the majority of positions and directions measured., This research received funding from the European Union’s Horizon H2020 research and innovation program under grant agreement No814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Assessment of novel modal testing methods for structures rotating in water

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The current paper presents an investigation into novel modal testing methods applied to a disk–shaft structure at different rotating speeds in air and water. The structure was excited using three different methods: an instrumented hammer, a piezoelectric PZT patch glued on the disk and a transient ramp-up. The structural response was measured using an accelerometer and strain gauges mounted on board as well as accelerometers and displacement lasers mounted off board. The potential to excite the natural frequencies using each excitation method and to detect natural frequencies with each sensor was analyzed and compared. Numerical structural and acoustic– structural modal and harmonic analyses of the non-rotating disk in air and water were also performed, taking into consideration the PZT patch. The numerical results showed a close agreement with the experimental ones in both air and water. It was found that the rotating speed of the disk modified the detected natural frequencies, depending on the frame of reference of the sensor. Finally, the PZT patch and the transient ramp-up were proven to be reliable methods to excite the natural frequencies of the current test rig and to be potentially applicable in full-scale hydraulic turbines under operating conditions., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant agreement No. 814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the vaneless space vortex structures in a Kaplan turbine model operating at speed no load

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Mulu, Berhanu
  • Högström, Carl-Maikel
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The growing installation of intermittent renewable energy sources is forcing hydraulic turbines to work more frequently at speed no load when dangerous vaneless space vortex structures and stochastic flow phenomena can occur. An experimental campaign has been performed in a reduced-scale Kaplan turbine model at speed no load for different combinations of guide vane and runner blade angles under non-cavitation and cavitation conditions. Several simultaneous vaneless space vortex structures, all of them inducing torsional rotor vibrations, have been observed. Nonetheless, only one of them has been found to dominate over the rest depending on the blade and guide vane angles. Off-board pressures, torques and vibrations as well as on-board strains have been measured to characterize their nature, intensity, dynamic behavior and induced structural response. Their precession frequencies have been found to depend on the discharge factor, the number of vortices and their location inside the vaneless space. Under cavitation conditions, their dynamic behavior has not been significantly altered but the induced structural response has increased at the low-pressure side of the turbine., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant number 814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Experimental and numerical study on the detection of fatigue failure in hydraulic turbines

  • Sánchez Botello, Xavier
  • de la Torre, Adolfo
  • Roig Bauzà, Rafel
  • Jou Santacreu, Esteban|||0000-0001-6991-6250
  • Torre Rodríguez, Óscar de la
  • Ayneto Gubert, Javier|||0000-0003-4373-7603
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
Detecting fatigue cracks in hydraulic turbine runners is costly, as it requires to stop the unit, empty it of water and access the runner for inspection. Thus, an alternative way based on monitoring the changes of the structural modal response induced by the formation and growth of a crack has been investigated. To do so, the crack propagation induced by a resonance has been numerically predicted and experimentally machined on a disk-like structure that resembles a Kaplan turbine runner. The analysis of the results shows how the different stages of the fatigue crack growth can be monitored based on the change of the natural frequencies and mode shapes of several specific modes. Based on the obtained results, a Structural Health Monitoring system is going to be designed to monitor the turbine runner modes of vibration without the need to stop and inspect the unit., This work was supported by the European Union’s Horizon 2020 research and innovation program under grant agreement number 814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Fiber bragg grating sensors for underwater vibration measurement: potential hydropower applications

  • Torre Rodríguez, Óscar de la
  • Floris, Ingazio
  • Sales, Salvador
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The present paper assesses the performance and characteristics of fiber Bragg grating sensors, with a special interest in their applications in hydraulic machinery and systems. The hydropower industry is turning to this technology with high expectations of obtaining high quality data to validate and calibrate numerical models that could be used as digital twins of key assets, further strengthening the sector’s relevant position within industry 4.0. Prior to any validation, fiber Bragg grating sensors’ ability to perform well underwater for long periods of time with minimal degradation, and their ease of scalability, drew the authors´ attention. A simplified modal analysis of a partially submerged beam is proposed here as a first step to validate the potential of this type of technology for hydropower applications. Fiber Bragg grating sensors are used to obtain the beam’s natural frequencies and to damp vibrations under different conditions. The results are compared with more established waterproof electric strain gauges and a laser vibrometer with good agreement. The presence of several sensors in a single fiber ensures high spatial resolution, fundamental to precisely determine vibration patterns, which is a main concern in this industry. In this work, the beam’s vibration patterns have been successfully captured under different excitations and conditions., This research was funded by Horizon 2020 research and innovation program under grant agreement No 814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the added modal coefficients of a rotating submerged cylinder induced by a whirling motion. Part 1: Experimental investigation

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Jou Santacreu, Esteban|||0000-0001-6991-6250
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The operation of submerged rotating machines, such as marine current or tidal turbines, can present deleterious fluid phenomena that may provoke extreme structural vibrations. To predict their dynamic responses, it is necessary to know the added modal coefficients of their runners under a whirling motion. For that purpose, a bespoke test rig was designed to investigate the added modal coefficients of a submerged cylinder, which could rotate at different speeds both in air and completely submerged in water inside a cylindrical tank. First, the modes of vibration were experimentally measured by exciting the cylinder with a push-release method during steady tests or with ramps in rotating speed during transient tests. The calculated natural frequencies and damping ratios were then used in a mathematical model of the dynamic system to calculate the added modal coefficients. During steady tests, the natural frequencies and damping ratios of the whirling modes changed significantly as a function of the rotating speed. Additionally, a whirling mode was observed to change its direction at a given rotating speed. During transient tests, rotating speed ramps with high accelerations were found to present lower lock-in amplitude and frequencies. Moreover, fast downward ramps presented lock-in amplitudes four times higher than fast upward ramps. Consequently, the added modal coefficients changed accordingly as a function of the rotating speed, ramp acceleration, and ramp direction. For these reasons, it was confirmed that the modal responses of submerged rotating bodies must be calculated for each operational rotating speed, even at low velocities, and for each transient event in order to precisely predict their vibration behaviors., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant agreement No. 814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Understanding the influence of wake cavitation on the dynamic response of hydraulic profiles under lock-in conditions

  • Roig Bauzà, Rafel
  • Chen, Jian
  • Torre Rodríguez, Óscar de la
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
To accelerate the integration of fluctuating renewable energy technologies in the power systems, it is necessary to increase the flexibility of hydropower by operating turbines at off-design conditions. Unfortunately, this strategy causes deleterious flow phenomena such as von Kármán’s vortices at the wake of the vanes and/or blades. When their shedding frequency lies in the vicinity of a structure’s natural frequency, lock-in occurs and vibration amplitudes increase significantly. Moreover, if cavitation occurs at the centers of these vortices, the structure’s dynamic response will be modified. In order to understand this interaction and to avoid its negative consequences, the vibration behavior of a NACA 0009 hydrofoil under a torsional lock-in condition was numerically simulated for cavitation-free and cavitating-flow conditions. The results showed that the presence of vortex cavitation modified the formation and growth process of shed von Kármán vortices in the near-wake region which, in turn, caused an increase of the work performed by the hydrofoil deformation on the surrounding flow and a sharp decrease of the maximum vibration amplitude under resonance conditions., This research was funded by Horizon 2020 research and innovation program under grant agreement No 814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Fatigue damage analysis of a Kaplan turbine model operating at off-design and transient conditions

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Torre Rodríguez, Óscar de la
  • Ayneto Gubert, Javier|||0000-0003-4373-7603
  • Högström, Carl-Maikel
  • Mulu, Berhanu
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
© The Author(s) 2023., The current renewable energy market forces hydraulic turbines to operate for longer periods of time at off-design and transient conditions. Their life expectancy is then decreased due to the wear provoked by flow instabilities and stochastic flow excitations. This study presents an experimental investigation into the fatigue damage induced on the runner blades of a Kaplan turbine model when working at speed-no-load (SNL), part load (PL) and during ramps of load. The unit was equipped with on-board sensors on the blades and the shaft as well as with off-board sensors installed on the supporting structure and the draft tube cone. The results reveal that operation at SNL induces more fatigue damage on the runner blades than at PL. The damage is then mainly induced by stochastic flow excitations at SNL and by the rotating mode of the rotating vortex rope (RVR) at PL. The ramps of load, when crossing each operating condition, cause levels of damage similar to those found in stationary operation. Finally, it was proved that the blade fatigue damage can be estimated from on-board shaft measurements at any condition. However, the blade fatigue damage can only be estimated using off-board measurements when the RVR is fully developed at PL., This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 814958. Additionally, the present authors would like to acknowledge the technical support received from Vattenfall AB., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

On the added modal coefficients of a rotating submerged cylinder induced by a whirling motion. Part 2: Numerical investigation

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
Part 2 of this work presents a numerical methodology, validated using the experimental results presented in Part 1, to calculate the added modal coefficients of a submerged cylinder in water both when it oscillates and when it rotates with a whirling motion. The numerical methodology is based on computational fluid dynamic simulations that obtain the added modal forces on the cylinder when it is forced to vibrate with mode shapes calculated using acoustic-structural modal analysis. Then, these forces are processed with a curve-fitting algorithm to extract all the coefficients. Most numerical coefficients presented a close agreement with the corresponding experimental ones, although the added modal damping was overestimated. In general, the added modal mass was found to be independent of both the rotating speed and the whirling frequency except for low whirling frequencies when it increased. The added modal damping was found to depend on both parameters, and the rest of the coefficients were independent of the whirling frequency and only depended on the rotating speed. As a conclusion, this numerical approach has permitted the study of particular conditions that could not be experimentally tested and thus broadened the knowledge of the behavior of the added modal coefficients of rotating submerged cylinders., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant agreement No. 814958., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Understanding the influence of wake cavitation on the dynamic response of hydraulic profiles under lock-in conditions

  • Roig Bauzà, Rafel
  • Chen, Jian
  • Torre Rodríguez, Óscar de la
  • Escaler Puigoriol, Francesc Xavier
To accelerate the integration of fluctuating renewable energy technologies in the power systems, it is necessary to increase the flexibility of hydropower by operating turbines at off-design conditions. Unfortunately, this strategy causes deleterious flow phenomena such as von Kármán’s vortices at the wake of the vanes and/or blades. When their shedding frequency lies in the vicinity of a structure’s natural frequency, lock-in occurs and vibration amplitudes increase significantly. Moreover, if cavitation occurs at the centers of these vortices, the structure’s dynamic response will be modified. In order to understand this interaction and to avoid its negative consequences, the vibration behavior of a NACA 0009 hydrofoil under a torsional lock-in condition was numerically simulated for cavitation-free and cavitating-flow conditions. The results showed that the presence of vortex cavitation modified the formation and growth process of shed von Kármán vortices in the near-wake region which, in turn, caused an increase of the work performed by the hydrofoil deformation on the surrounding flow and a sharp decrease of the maximum vibration amplitude under resonance conditions., This research was funded by Horizon 2020 research and innovation program under grant agreement No 814958., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Fatigue damage analysis of a Kaplan turbine model operating at off-design and transient conditions

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Torre Rodríguez, Óscar de la
  • Ayneto Gubert, Javier
  • Högström, Carl-Maikel
  • Mulu, Berhanu
  • Escaler Puigoriol, Francesc Xavier
© The Author(s) 2023., The current renewable energy market forces hydraulic turbines to operate for longer periods of time at off-design and transient conditions. Their life expectancy is then decreased due to the wear provoked by flow instabilities and stochastic flow excitations. This study presents an experimental investigation into the fatigue damage induced on the runner blades of a Kaplan turbine model when working at speed-no-load (SNL), part load (PL) and during ramps of load. The unit was equipped with on-board sensors on the blades and the shaft as well as with off-board sensors installed on the supporting structure and the draft tube cone. The results reveal that operation at SNL induces more fatigue damage on the runner blades than at PL. The damage is then mainly induced by stochastic flow excitations at SNL and by the rotating mode of the rotating vortex rope (RVR) at PL. The ramps of load, when crossing each operating condition, cause levels of damage similar to those found in stationary operation. Finally, it was proved that the blade fatigue damage can be estimated from on-board shaft measurements at any condition. However, the blade fatigue damage can only be estimated using off-board measurements when the RVR is fully developed at PL., This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 814958. Additionally, the present authors would like to acknowledge the technical support received from Vattenfall AB., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the vaneless space vortex structures in a Kaplan turbine model operating at speed no load

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Mulu, Berhanu
  • Högström, Carl-Maikel
  • Escaler Puigoriol, Francesc Xavier
The growing installation of intermittent renewable energy sources is forcing hydraulic turbines to work more frequently at speed no load when dangerous vaneless space vortex structures and stochastic flow phenomena can occur. An experimental campaign has been performed in a reduced-scale Kaplan turbine model at speed no load for different combinations of guide vane and runner blade angles under non-cavitation and cavitation conditions. Several simultaneous vaneless space vortex structures, all of them inducing torsional rotor vibrations, have been observed. Nonetheless, only one of them has been found to dominate over the rest depending on the blade and guide vane angles. Off-board pressures, torques and vibrations as well as on-board strains have been measured to characterize their nature, intensity, dynamic behavior and induced structural response. Their precession frequencies have been found to depend on the discharge factor, the number of vortices and their location inside the vaneless space. Under cavitation conditions, their dynamic behavior has not been significantly altered but the induced structural response has increased at the low-pressure side of the turbine., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant number 814958., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Assessment of fiber Bragg grating sensors for monitoring shaft vibrations of hydraulic turbines

  • Sánchez Botello, Xavier
  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Madrigal, Javier
  • Sales, Salvador
  • Escaler Puigoriol, Francesc Xavier
The structural dynamic response of hydraulic turbines needs to be continuously monitored to predict incipient failures and avoid catastrophic breakdowns. Current methods based on traditional off-board vibration sensors mounted on fixed components do not permit inferring loads induced on rotating parts with enough accuracy. Therefore, the present paper assesses the performance of fiber Bragg grating sensors to measure the vibrations induced on a rotating shaft–disc assembly partially submerged in water resembling a hydraulic turbine rotor. An innovative mounting procedure for installing the sensors is developed and tested, which consists of machining a thin groove along a shaft line to embed a fiber-optic array that can pass through the bearings. At the top of the shaft, a rotary joint is used to extract, in real time, the signals to the interrogator. The shaft strain distribution is measured with high spatial resolution at different rotating speeds in air and water. From this, the natural frequencies, damping ratios, and their associated mode shapes are quantified at different operating conditions. Additionally, the change induced in the modes of vibration by the rotation effects is well captured. All in all, these results validate the suitability of this new fiber-optic technology for such applications and its overall better performance in terms of sensitivity and spatial resolution relative to traditional equipment. The next steps will consist of testing this new sensing technology in actual full-scale hydraulic turbines., This work was supported by the funding received from the European Union’s Horizon H2020 research and innovation program (grant agreement no: 814958) and by the I+D+i project SYNERGY PID2020-118310RBI00 funded by the MCIN/AEI/10.13039/501100011033., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the rotating vortex rope and its induced structural response in a Kaplan turbine model

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Escaler Puigoriol, Francesc Xavier
  • Mulu, Berhanu
  • Högström, Carl-Maikel
The rotating vortex rope, which can be decomposed in the rotating and the plunging modes, is the origin of pressure fluctuations in the draft tube cone when hydraulic turbines operate at part load, compromising the structural integrity and limiting the output load. A measurement campaign was carried out in a Kaplan turbine model which is a replica of the experimental 10 MW Porjus U9 prototype machine along a propeller curve to study the rotating vortex rope’s excitation levels and the induced structural responses. A complete set of sensors mounted on-board and off-board was used to measure pressures, forces, torques, accelerations, displacements, and strains. The characteristic frequencies and amplitudes of the pressure fluctuations and of the corresponding induced loads and vibrations associated with the two modes were quantified in a wide range of operating conditions at part load. The two modes are detected at different frequencies depending on the sensor position. Moreover, their frequencies change depending on the discharge and present different amplitudes depending on the mode. Particularly, the rotating mode shows higher amplitudes than the plunging mode in the majority of positions and directions measured., This research received funding from the European Union’s Horizon H2020 research and innovation program under grant agreement No814958., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the added modal coefficients of a rotating submerged cylinder induced by a whirling motion. Part 2: Numerical investigation

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Escaler Puigoriol, Francesc Xavier
Part 2 of this work presents a numerical methodology, validated using the experimental results presented in Part 1, to calculate the added modal coefficients of a submerged cylinder in water both when it oscillates and when it rotates with a whirling motion. The numerical methodology is based on computational fluid dynamic simulations that obtain the added modal forces on the cylinder when it is forced to vibrate with mode shapes calculated using acoustic-structural modal analysis. Then, these forces are processed with a curve-fitting algorithm to extract all the coefficients. Most numerical coefficients presented a close agreement with the corresponding experimental ones, although the added modal damping was overestimated. In general, the added modal mass was found to be independent of both the rotating speed and the whirling frequency except for low whirling frequencies when it increased. The added modal damping was found to depend on both parameters, and the rest of the coefficients were independent of the whirling frequency and only depended on the rotating speed. As a conclusion, this numerical approach has permitted the study of particular conditions that could not be experimentally tested and thus broadened the knowledge of the behavior of the added modal coefficients of rotating submerged cylinders., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant agreement No. 814958., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

On the added modal coefficients of a rotating submerged cylinder induced by a whirling motion. Part 1: Experimental investigation

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Jou Santacreu, Esteban
  • Escaler Puigoriol, Francesc Xavier
The operation of submerged rotating machines, such as marine current or tidal turbines, can present deleterious fluid phenomena that may provoke extreme structural vibrations. To predict their dynamic responses, it is necessary to know the added modal coefficients of their runners under a whirling motion. For that purpose, a bespoke test rig was designed to investigate the added modal coefficients of a submerged cylinder, which could rotate at different speeds both in air and completely submerged in water inside a cylindrical tank. First, the modes of vibration were experimentally measured by exciting the cylinder with a push-release method during steady tests or with ramps in rotating speed during transient tests. The calculated natural frequencies and damping ratios were then used in a mathematical model of the dynamic system to calculate the added modal coefficients. During steady tests, the natural frequencies and damping ratios of the whirling modes changed significantly as a function of the rotating speed. Additionally, a whirling mode was observed to change its direction at a given rotating speed. During transient tests, rotating speed ramps with high accelerations were found to present lower lock-in amplitude and frequencies. Moreover, fast downward ramps presented lock-in amplitudes four times higher than fast upward ramps. Consequently, the added modal coefficients changed accordingly as a function of the rotating speed, ramp acceleration, and ramp direction. For these reasons, it was confirmed that the modal responses of submerged rotating bodies must be calculated for each operational rotating speed, even at low velocities, and for each transient event in order to precisely predict their vibration behaviors., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant agreement No. 814958., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Fiber bragg grating sensors for underwater vibration measurement: potential hydropower applications

  • Torre Rodríguez, Óscar de la
  • Floris, Ingazio
  • Sales, Salvador
  • Escaler Puigoriol, Francesc Xavier
The present paper assesses the performance and characteristics of fiber Bragg grating sensors, with a special interest in their applications in hydraulic machinery and systems. The hydropower industry is turning to this technology with high expectations of obtaining high quality data to validate and calibrate numerical models that could be used as digital twins of key assets, further strengthening the sector’s relevant position within industry 4.0. Prior to any validation, fiber Bragg grating sensors’ ability to perform well underwater for long periods of time with minimal degradation, and their ease of scalability, drew the authors´ attention. A simplified modal analysis of a partially submerged beam is proposed here as a first step to validate the potential of this type of technology for hydropower applications. Fiber Bragg grating sensors are used to obtain the beam’s natural frequencies and to damp vibrations under different conditions. The results are compared with more established waterproof electric strain gauges and a laser vibrometer with good agreement. The presence of several sensors in a single fiber ensures high spatial resolution, fundamental to precisely determine vibration patterns, which is a main concern in this industry. In this work, the beam’s vibration patterns have been successfully captured under different excitations and conditions., This research was funded by Horizon 2020 research and innovation program under grant agreement No 814958., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Assessment of novel modal testing methods for structures rotating in water

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Escaler Puigoriol, Francesc Xavier
The current paper presents an investigation into novel modal testing methods applied to a disk–shaft structure at different rotating speeds in air and water. The structure was excited using three different methods: an instrumented hammer, a piezoelectric PZT patch glued on the disk and a transient ramp-up. The structural response was measured using an accelerometer and strain gauges mounted on board as well as accelerometers and displacement lasers mounted off board. The potential to excite the natural frequencies using each excitation method and to detect natural frequencies with each sensor was analyzed and compared. Numerical structural and acoustic– structural modal and harmonic analyses of the non-rotating disk in air and water were also performed, taking into consideration the PZT patch. The numerical results showed a close agreement with the experimental ones in both air and water. It was found that the rotating speed of the disk modified the detected natural frequencies, depending on the frame of reference of the sensor. Finally, the PZT patch and the transient ramp-up were proven to be reliable methods to excite the natural frequencies of the current test rig and to be potentially applicable in full-scale hydraulic turbines under operating conditions., This research was funded by the European Union’s Horizon H2020 research and innovation program under grant agreement No. 814958., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental and numerical study on the detection of fatigue failure in hydraulic turbines

  • Sánchez Botello, Xavier
  • de la Torre, Adolfo
  • Roig Bauzà, Rafel
  • Jou Santacreu, Esteban
  • Torre Rodríguez, Óscar de la
  • Ayneto Gubert, Javier
  • Escaler Puigoriol, Francesc Xavier
Detecting fatigue cracks in hydraulic turbine runners is costly, as it requires to stop the unit, empty it of water and access the runner for inspection. Thus, an alternative way based on monitoring the changes of the structural modal response induced by the formation and growth of a crack has been investigated. To do so, the crack propagation induced by a resonance has been numerically predicted and experimentally machined on a disk-like structure that resembles a Kaplan turbine runner. The analysis of the results shows how the different stages of the fatigue crack growth can be monitored based on the change of the natural frequencies and mode shapes of several specific modes. Based on the obtained results, a Structural Health Monitoring system is going to be designed to monitor the turbine runner modes of vibration without the need to stop and inspect the unit., This work was supported by the European Union’s Horizon 2020 research and innovation program under grant agreement number 814958., Peer Reviewed, Preprint