Pasar al contenido principal

DESARROLLO Y EVALUACION DE TECNOLOGIAS BASADAS EN UAV Y OBIA PARA LA DETECCION DE MALAS HIERBAS Y OPTIMIZAR SU GESTION

AGL2014-52465-C4-4-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2014
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessing Optimal Flight Parameters for Generating Accurate Multispectral Orthomosaicks by UAV to Support Site-Specific Crop Management

  • Mesas-Carrascosa, Francisco Javier
  • Torres-Sánchez, Jorge
  • Clavero-Rumbao, Inmaculada
  • García-Ferrer, Alfonso
  • Peña Barragán, José Manuel
  • Borra-Serrano, Irene
  • López Granados, Francisca
This article describes the technical specifications and configuration of a multirotor unmanned aerial vehicle (UAV) to acquire remote images using a six-band multispectral sensor. Several flight missions were programmed as follows: three flight altitudes (60, 80 and 100 m), two flight modes (stop and cruising modes) and two ground control point (GCP) settings were considered to analyze the influence of these parameters on the spatial resolution and spectral discrimination of multispectral orthomosaicked images obtained using Pix4Dmapper. Moreover, it is also necessary to consider the area to be covered or the flight duration according to any flight mission programmed. The effect of the combination of all these parameters on the spatial resolution and spectral discrimination of the orthomosaicks is presented. Spectral discrimination has been evaluated for a specific agronomical purpose: to use the UAV remote images for the detection of bare soil and vegetation (crop and weeds) for in-season site-specific weed management. These results show that a balance between spatial resolution and spectral discrimination is needed to optimize the mission planning and image processing to achieve every agronomic objective. In this way, users do not have to sacrifice flying at low altitudes to cover the whole area of interest completely., This research was partially financed by the RECUPERA-2020 (an agreement between CSIC and Spanish MINECO, EU-FEDER funds) and AGL2014-52465-C4-4-R Projects (MINECO, EU-FEDER funds). Research of Torres-Sánchez and Peña were financed by FPI and Ramon y Cajal Programs, respectively (Spanish Ministry of Economy and Competitiveness). We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Quantifying pruning impacts on olive tree architecture and annual canopy growth by using UAV-based 3D modelling

  • Jiménez-Brenes, Francisco Manuel
  • López Granados, Francisca
  • Castro, Ana Isabel de
  • Torres-Sánchez, Jorge
  • Serrano, Nicolás
  • Peña Barragán, José Manuel
[Background] Tree pruning is a costly practice with important implications for crop harvest and nutrition, pest and disease control, soil protection and irrigation strategies. Investigations on tree pruning usually involve tedious on-ground measurements of the primary tree crown dimensions, which also might generate inconsistent results due to the irregular geometry of the trees. As an alternative to intensive field-work, this study shows a innovative procedure based on combining unmanned aerial vehicle (UAV) technology and advanced object-based image analysis (OBIA) methodology for multi-temporal three-dimensional (3D) monitoring of hundreds of olive trees that were pruned with three different strategies (traditional, adapted and mechanical pruning). The UAV images were collected before pruning, after pruning and a year after pruning, and the impacts of each pruning treatment on the projected canopy area, tree height and crown volume of every tree were quantified and analyzed over time., [Results] The full procedure described here automatically identified every olive tree on the orchard and computed their primary 3D dimensions on the three study dates with high accuracy in the most cases. Adapted pruning was generally the most aggressive treatment in terms of the area and volume (the trees decreased by 38.95 and 42.05% on average, respectively), followed by trees under traditional pruning (33.02 and 35.72% on average, respectively). Regarding the tree heights, mechanical pruning produced a greater decrease (12.15%), and these values were minimal for the other two treatments. The tree growth over one year was affected by the pruning severity and by the type of pruning treatment, i.e., the adapted-pruning trees experienced higher growth than the trees from the other two treatments when pruning intensity was low (<10%), similar to the traditionally pruned trees at moderate intensity (10–30%), and lower than the other trees when the pruning intensity was higher than 30% of the crown volume., [Conclusions] Combining UAV-based images and an OBIA procedure allowed measuring tree dimensions and quantifying the impacts of three different pruning treatments on hundreds of trees with minimal field work. Tree foliage losses and annual canopy growth showed different trends as affected by the type and severity of the pruning treatments. Additionally, this technology offers valuable geo-spatial information for designing site-specific crop management strategies in the context of precision agriculture, with the consequent economic and environmental benefits., This research was funded by the AGL2014-52465-C4-4R Project (The Spanish Ministry of Economy, Industry and Competitiveness, MINECO) and the CSIC-Intramural-Project (Ref. 201640E034). The research performed by Dr. de Castro, Dr. Torres-Sánchez and Dr. Peña was financed by the Juan de la Cierva, FPI and Ramón y Cajal Programmes (Spanish MINECO funds), respectively. We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Uso de drones (UAV) para la detección de grama en cubiertas de viña

  • Castro, Ana Isabel de
  • Peña Barragán, José Manuel
  • Torres-Sánchez, Jorge
  • Jiménez-Brenes, Francisco Manuel
  • Valencia, Francisco
  • López Granados, Francisca
El manejo adecuado de las cubiertas vegetales en viñedos permite equilibrar el vigor y rendimiento de la viña, resultando en una mejora de la calidad de la cosecha. Estas ventajas quedan mermadas con las infestaciones de grama (Cynodon dactylon), una mala hierba perenne difícilmente controlable. Por ello se analizaron imágenes obtenidas en viñedos con vehículos aéreos no tripulados (UAV), mediante técnicas basadas en objetos (OBIA) para determinar la posición de los rodales de grama. El algoritmo desarrollado permitió la clasificación automática de las cuatro clases (viña, suelo desnudo, grama y cubierta vegetal) y la generación de mapas de grama para su control localizado. Esta técnica de viticultura de precisión conlleva una disminución del coste económico y medioambiental del tratamiento., Esta investigación fue financiada por el proyecto AGL2014-52465-C4-4R (Ministerio de Economía y Competitividad, fondos FEDER: Fondo Europeo de Desarrollo Regional). La investigación del Dr. Jorge Torres-Sánchez, Dr. Ana de Castro y el Dr. José M. Peña fue financiada por los programas FPI (BES-2012-052424), Juan de la Cierva (MINECO) y Ramón y Cajal (MINECO), respectivamente., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Accurate ortho-mosaicked six-band multispectral UAV images as affected by mission planning for precision agriculture proposes

  • Mesas-Carrascosa, Francisco Javier
  • Clavero-Rumbao, Inmaculada
  • Torres-Sánchez, Jorge
  • García-Ferrer, Alfonso
  • Peña Barragán, José Manuel
  • López Granados, Francisca
Weed mapping at very early phenological stages of crop and weed plants for site-specific weed management can be achieved by using ultra-high spatial and high spectral resolution imagery provided by multispectral sensors on-board an unmanned aerial vehicle (UAV). These UAV images cannot cover the whole field, resulting in the need to take a sequence of multiple overlapped images. Therefore, the overlapped images must be oriented and ortho-rectified to create an accurate ortho-mosaicked image of the entire field for further classification. Because the spatial quality of ortho-mosaicked images mainly depend on the flight altitude and percentage of overlap, this paper describes the effect of flight parameters using a multirotor UAV and a multispectral camera on the mosaicking workflow. The objective is to define the best configuration for the mission planning to generate accurate ortho-images. A set of flights with a range of altitudes (30, 40, 50, 60, 70, 80, and 90 m) above ground level (AGL) and two end-lap and side-lap settings (60–30% and 70–40%) were studied. The spatial accuracy of ortho-mosaics was evaluated taking into consideration the ASPRS test. The results showed that the best flight setting to keep the spatial accuracy in the bundle adjustment was 70–40% overlap and altitudes AGL ranging from 60 to 90 m. At these flight altitudes, the spatial resolution was quite similar, making it possible to optimize the mission planning, flying at a higher altitude and increasing the area overflow without decreasing the ortho-mosaic spatial quality. This study has relevant implications for further use in detecting weed seedlings in crops., This research was partly funded by the AGL2014-52465-C4-4R project (Spanish Ministry of Economy and Competition, FEDER Funds: Fondo Europeo de Desarrollo Regional). Research of Mr Torres-Sánchez and Dr Peña was financed by the FPI [grant number BES-2012-052424] and Ramón y Cajal [grant number RYC-2013-14874] Programs (Spanish MINECO funds), respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Object-based early monitoring of a grass weed in a grass crop using high resolution UAV imagery

  • López Granados, Francisca
  • Torres-Sánchez, Jorge
  • Castro, Ana Isabel de
  • Serrano Pérez, Angélica
  • Mesas-Carrascosa, Francisco Javier
  • Peña Barragán, José Manuel
Sorghum halepense (johnsongrass) is a perennial weed with a vegetative reproductive system and one of the most competitive weeds in maize showing a spatial distribution in compact patches. When maize is irrigated, successive weed emergences occur in the early phenological phases of the crop, which require several herbicide applications. Our aim was to provide an accurate tool for an early detection and mapping of johnsongrass patches and delineate the actual surface area requiring a site-specific herbicide treatment based on the weed coverage. This early detection represents a major challenge in actual field scenarios because both species are in the Poaceae family, and show analogous spectral patterns, an extraordinarily similar appearance and a parallel phenological evolution. To solve this, an automatic OBIA (object-based-image-analysis) procedure was developed to be applied on orthomosaicked images using visible (red-green-blue bands) and multispectral (red-green-blue and near infrared bands) cameras collected by an unmanned aerial vehicle (UAV) that flew at altitudes of 30, 60 and 100 m on two maize fields. One of our first phases was the generation of accurate orthomosaicked images of an herbaceous crop such as maize, which presented a repetitive pattern and nearly no invariant parameters to conduct the aerotriangulation. Here, we show that high-quality orthomosaicks were produced from both cameras and that they were able to be the first step for mapping the johnsongrass patches. The most accurate weed maps were obtained using the multispectral camera at an altitude of 30 m in both fields. These maps were then used to design a site-specific weed management program, and we demonstrated that potential herbicide savings ranged from 85 to 96 %. Our results showed that accurate and timely maps of johnsongrass patches in maize can be a key element in achieving site-specific and sustainable herbicide applications for reducing spraying herbicides and costs., This research was partially financed by the AGL2014-52465-C4-4-R Spanish MINECO, EU-FEDER funds. Research of Mr. Torres-Sánchez and Dr. Peña was financed by the FPI (BES-2012-052424) and Ramón y Cajal (RYC-2013-14874) Programs, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Últimos avances en tecnologías para la detección y el control de las malas hierbas

  • Fernández-Quintanilla, César
  • Dorado, José
  • Andújar, Dionisio
  • Peña Barragán, José Manuel
  • Ribeiro Seijas, Ángela
  • Castro, Ana Isabel de
  • López Granados, Francisca
Durante los últimos años el desarrollo de nuevas tecnologías para la agricultura de precisión ha alcanzado un considerable grado de madurez. En el ámbito específico de la gestión de las malas hierbas se han desarrollado numerosas tecnologías tanto de detección como de actuación. A los procedimientos disponibles para la detección desde satélite o d,esde avión se han unido otros mucho más precisos para la detección desde drones volando a baja altura. Por otro lado, la disponibilidad actual de sensores y cámaras 2D y 3D de muy alta resolución y de ordenadores más rápidos capaces de procesar grandes volúmenes de datos abre la posibilidad de llevar a cabo actuaciones en tiempo real. En este trabajo se expone una breve síntesis de los últimos avances producidos en sistemas de detección aérea y terrestre así como de algunos de los equipos inteligentes disponibles para el control físico o químico de las malas hierbas detectadas., Parte de los trabajos expuestos están siendo financiados por los proyectos AGL2014-52465-C4-1R; C4-3R y C4-4R integrados todos en un proyecto coordinado (Ministerio de Economía y Competitividad, fondos FEDER: Fondo Europeo de Desarrollo Regional)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Papaver rhoeas L. mapping with cokriging using UAV imagery

  • Jurado-Expósito, Montserrat
  • Castro, Ana Isabel de
  • Torres-Sánchez, Jorge
  • Jiménez-Brenes, Francisco Manuel
  • López Granados, Francisca
Accurately mapping the spatial distribution of weeds within a field is a first step towards effective Site-specific Weed Management. The main objective of this study was to investigate if the multivariate geostatistical method of cokriging (COK) can be used to improve the accuracy of Papaver rhoeas L. infestations maps in winter wheat fields using high-resolution UAV imagery as ancillary information. The primary variable was obtained by intensive grid weed density field samplings and the secondary variables were derived from the UAV imagery taken the same day as the weed field samplings (e.g. wavebands and derivative products, such as band ratios and vegetation indexes). Univariate Ordinary Kriging (OK) and multivariate cokriging (COK) interpolation methods were used and compared for Papaver density mapping. The performances of the different methods were assessed by cross-validation. The results indicated that COK outperformed OK in the spatial interpolation of Papaver density. COK reduced the prediction errors and enhanced the accuracy of Papaver estimates maps. The best performances were obtained when COK was performed with the UAV-secondary variables that yielded the highest correlation with Papaver density and produced the strongest spatial cross-semivariograms. On average, the COK with UAV-derived ancillary variables improved the accuracy of mapping Papaver density by 11 to 21% compared with OK. The results suggest the great potential of high-resolution UAV imagery as a source of ancillary information to improve the accuracy of spatial mapping of sparsely sampled target variables using COK., This research was financed by the AGL2014-52465-C4-4-R and AGL2017-83325-C4-4-R MINECO (Spanish Ministry of Economy and Competition, FEDER Funds). Research of AI. de Castro was financed by Juan de la Cierva (MINECO) program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A LiDAR-Based System to Assess Poplar Biomass

  • Andújar, Dionisio
  • Escolà, A.
  • Rosell Polo, Joan R.
  • Rueda Ayala, Víctor
  • Fernández Quintanilla, César
  • Ribeiro Seijas, Ángela
  • Dorado, José
This study evaluated the capabilities of a LiDAR-based system to characterize poplar trees for biomass production. The precision of the system was assessed by analyzing the relationship between the distance records and biophysical parameters. The terrestrial laser scanner (TLS) system consisted of a 2D time-of-flight LiDAR sensor, a gimbal to dynamically stabilize the sensor and a RTK-GPS to georeference its location and, subsequently, the sensor data. The sensor and its stabilizer were fixed facing downwards, on a metal frame designed for this purpose. Then, it was mounted on an all-terrain vehicle to perform 2D scans in planes perpendicular to the travel direction. Distances between the sensor and the surrounding objects had a high spatial resolution, providing high density 3D point clouds. Results on the reliability of the LiDAR system to estimate plant height showed a significant relationship between the sensor readings and actual poplar height and biomass data. In addition, tree biomass and tree volume were properly estimated in the point cloud. Regression analysis showed significant estimates of 0.79 and 0.89 for biomass and volume, respectively. These results reveal the potential of the LiDAR sensor to estimate both, plant height and plant biomass., This research was funded by the CICyT (Commision Interministerial de Ciencia y Tecnología, Spain), under Agreement No. AGL2011-25243 and AGL2014-52465-C4., Peer reviewed