Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The Transformation of Coal-Mining Waste Minerals in the Pozzolanic Reactions of Cements

  • Giménez-García, Rosario
  • Vigil de la Villa, R.
  • Rubio, Virginia
  • Frías, Moisés
The cement industry has the potential to become a major consumer of recycled waste materials that are transformed and recycled in various forms as aggregates and pozzolanic materials. These recycled waste materials would otherwise have been dumped in landfill sites, leaving hazardous elements to break down and contaminate the environment. There are several approaches for the reuse of these waste products, especially in relation to clay minerals that can induce pozzolanic reactions of special interest in the cement industry. In the present paper, scientific aspects are discussed in relation to several inert coal-mining wastes and their recycling as alternative sources of future eco-efficient pozzolans, based on activated phyllosilicates. The presence of kaolinite in this waste indicates that thermal treatment at 600 °C for 2 h transformed these minerals into a highly reactive metakaolinite over the first seven days of the pozzolanic reaction. Moreover, high contents of metakaolinite, together with silica and alumina sheet structures, assisted the appearance of layered double hydroxides through metastable phases, forming stratlingite throughout the main phase of the pozzolanic reaction after 28 days (as recommended by the European Standard) as the reaction proceeded., This research has been supported by the Spanish Ministry of Economy and Competitiveness (Project Ref. MAT2012-37005-CO3-01/02/03 and BIA2015-65558-C3-1-2-3R (MINECO/FEDER)). The authors are also grateful to the Sociedad Anónima Hullera Vasco-Leonesa and to the Spanish Cement Institute (IECA) for their assistance with this research. We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Coal Mining Waste as a Future Eco-Efficient Supplementary Cementing Material: Scientific Aspects

  • Frías, Moisés
  • García, Rosario
  • Vigil de la Villa, R.
  • Martínez-Ramírez, S.
The stockpiling of tailings around coal mines poses a major environmental problem. Nonetheless, this clay mineral (kaolinite)-based waste can be reused as a supplementary cementitious material (recycled metakaolinite) in the manufacture of future eco-efficient cements. This paper explores the most significant scientific questions posed in connection with the conversion of this waste into pozzolans, such as the variation in product mineralogy depending on the sintering temperature and its effect on reaction kinetics in the pozzolan/Ca(OH)<sub>2</sub> system over a period of 365 days. The findings show that the optimal sintering temperature is 600 °C, such that the cementitious properties of the activated product are determined solely by the conversion of kaolinite into metakaolinite and are unaffected by the other clay minerals (micas). The presence of 20% activated coal waste favors the formation of larger amounts of aluminous phases such as C<sub>4</sub>AH<sub>13</sub> and C<sub>4</sub>AcH<sub>12</sub> than in the reference paste and enhances C–S–H gel polymerization., This research was funded by the Spanish Ministry of the Economy and Competitiveness under coordinated projects MAT2012-37005-CO3-01, BIA2015-65558-C3-1-2-3R (MINECO/FEDER). We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Coal-mining tailings as a pozzolanic material in cements industry

  • Yagüe, Santiago
  • Sánchez, Isabel
  • Vigil de la Villa, Raquel
  • García-Giménez, Rosario
  • Zapardiel, Antonio
  • Frías, Moisés
The generation of enormous volumes of mine-tailing waste is standard practice in the mining industry. Large quantities of these tailings are also sources of kaolinite-rich materials that accumulate in slag heaps, causing significant environmental degradation and visual impacts on the landscape. The consequences of coal refuse dumped in slagheaps calls for the study of eco-innovative solutions and the assessment of waste types. Moreover, the environmental benefits of reusing large amounts of contaminated waste are also evident. Hence, the objective of this investigation is to expand current knowledge of new siliceous-aluminium minerals and their pozzolanic activity. Four raw tailing samples are characterized to determine their chemical (by ICP/MS analysis), morphological (by SEM/EDX analysis), and mineralogical (by XRD analysis) compositions prior to their thermal activation that transforms the inert wastes at various temperatures into materials with cementitious properties. The results of XRD analysis following activation confirmed that the kaolinite content is fully transformed into metakaolinite. The coal refuse samples presented sufficiently reliable levels of pozzolanic activity for use as additives in industrial cements., This research was supported by the Spanish Ministry of Economy and Competitiveness (Project Ref BIA2015-65558-C3-1-2-3R (MINECO/FEDER)). The authors are also grateful to the Sociedad Anónima Huellera Vasco-Leonesa and to the Spanish Cement Institute (IECA) for their assistance with this research.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effects of calcination temperature and the addition of ZnO on coal waste activation: A mineralogical and morphological evolution

  • Vigil de la Villa, R.
  • García-Giménez, Rosario
  • Martínez-Ramírez, S.
  • Frías, Moisés
9 pags., 15 figs., 5 tabs., Eco-efficient cements based on industrial wastes constitute a priority line of research for the sustainability of the cement sector, in response to the challenges of the circular economy at a European level. Eco-innovation and investigation of new alternative sources of primary materials from waste arise as potential actions directed at the achievement of greater efficiency in the use of resources. From among the broad range of industrial wastes, those that contain kaolinite (K) and phyllosilicates are ideal as active additions in the manufacture of cements, having previously undergone a process of thermal activation. Earlier works have indicated that the chemical reactivity of natural K (untreated kaolin) may be increased through the addition of ZnO as a chemical agent. In this study, the effect of ZnO as a chemical agent is for the first time studied, when added to coal waste in proportions of 0.5, 1.0, 1.5 and 3.0% by weight, prior to the thermal activation process of the waste that is calcinated at 550°, 600°, and 650 °C for 2 h. The mineralogy and the pozzolanic activity of the activated products are considered, and their influence on the evolution of the hydrated phases at 1, 7, and 28 days of reaction in the pozzolan/lime system. Subsequently, the results are compared with those obtained from pure natural kaolinite activated at 600 °C/2 h, with ZnO addition and without chemical agent ZnO, with an added quantity of 1.0% in weight. The results showed important variations when the chemical activator (ZnO) was used for the natural kaolinite (NK) and the industrial waste. The chemical activator favors the disaggregation of the phyllosilicates from the aggregates, strengthening the pozzolanic reaction in the natural/lime kaolinite system. However, the activator in the coal waste/lime system, in addition to favoring the disaggregation of the aggregate, leaves epitaxial deposits on the surface and on the edges of the materials, saturating the substrate surface loading, with an inhibitory effect on the pozzolanic reaction. The abundance of metakaolinite (MK) and the partial dehydroxylation of the mica with its subsequent reorganization, explains the appearance of these minerals as one of the products of the reaction. With SEM/EDX, the existence of CeSeH gels of a spongy appearance may be observed following thermal activation of the coal waste; while if the activation is done under the combined effect of temperature and the addition of 1.0% ZnO, then the chemical activator favors the formation of long fibers and the appearance of gels, with compositions similar to LDH and calcium aluminates., The authors wish to express their gratitude and sincere appreciation to the Spanish Ministry of the Economy and Competitiveness under coordinated projects MAT2012-37005-CO3-01, BIA2015-65558-C3-1- 2-3R (MINECO/FEDER) for financing this research work and grateful to the Sociedad Anónima Hullera Vasco-Leonesa (Spain) and to the Spanish Cement Institute (IECA) for their assistance with this research., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ca/Si and Si/Al ratios of metakaolinite-based wastes: Their influence on mineralogy and mechanical strengths

  • García-Giménez, Rosario
  • Frías, Moisés
  • Vigil de la Villa, Raquel
  • Martínez-Ramírez, S.
Kaolinite-based wastes are researched as an alternative means of extracting metakaolinite, a pozzolanic product for the manufacture of eco-efficient cements. However, both crystallinity and the content of this crystalline phase play important roles during their thermal activation and, therefore, in their subsequent behavior in the matrix with cementitious properties. In this study, the initial compositions of two thermally activated products (paper sludge and coal waste) are studied for both the mineralogy and the mechanical properties of binary cements. The elemental composition of the materials was analyzed with X-ray Fluorescence (XRF). The mineralogy of the crystalline materials was determined by X-ray Diffraction (XRD). The sample morphology was determined with scanning electron microscopy (SEM). The pozzolanic activity is measured by accelerated methods and the preparation of the specimens of blended cement is prepared following the procedure described by Kock-Steinegger. The results showed that the pozzolanic activity of the waste (in terms of fixed lime) was similar at 90 days but that its reaction rate was different. The pozzolanic reaction of both wastes produced stratlingite and C-S-H gels, with the presence of C<sub>4</sub>AH<sub>13</sub>. The C-S-H gel generated with coal waste had very short chains, was poorer in Ca and was rich in Al. The addition of both wastes to the cement modified its mineralogical composition in comparison with a conventional cement, favoring the formation of C<sub>4</sub>AH<sub>13</sub> over the formation of ettringite., The authors are grateful to the Spanish Ministry of Economy and Competiveness (MINECO/FEDER) by the financial support (BIA2015-65558-C3-1/2/3-R) y a la Sociedad Anónima Hullera Vasco-Leonesa (León, Spain) and the Spanish Cement Institute (IECA, Madrid, Spain) for their support in this research.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Carbonation-induced mineralogical changes in coal mining waste blended cement pastes and their influence on mechanical and microporosity properties

  • Frías, Moisés
  • Vigil de la Villa, Raquel
  • García Giménez, Rosario
  • Rodríguez-Largo, Olga
  • Fernández-Carrasco, Lucía
  • Martínez-Ramírez, S.
The worldwide pursuit of new eco-efficient pozzolans is ongoing. Kaolinite-based waste is an eco-friendly source of recycled metakaolinite, a highly pozzolanic product. In this study, a blended cement paste containing 20% activated coal waste (ACW) was exposed to a 100% CO2 atmosphere at 65% RH for 7 days. The variations in its phase composition and strength were studied and compared to an OPC control. Both pastes were cured for 28 days prior to the carbonation test. Reaction kinetics were assessed using XRD, SEM/EDX, TG/DTG, FT-IR, Micro-Raman spectroscopy, pore solution pH and the cumulative carbonated fraction. The blended cement carbonated 68% faster than the control. While portlandite carbonation was the main reaction in both cements, decalcification was also observed (more intensely in the 20% ACW paste) in other hydraulic calcium phases (C-S-H gel, monocarboaluminate (C4AcH12), ettringite and tetracalcium aluminate (C4AH13). The end product of this reaction was calcium carbonate, mainly in the form of calcite, although traces of aragonite and amorphous carbonate were also detected. Compressive strength values rose with accelerated carbonation time and pore size reduction in both cement pastes., This research was funded by the Spanish Ministry of Economy and Competitiveness (Project Refs. MAT2012-37005-CO3-01/02/03) and MINECO/FEDER (BIA2015-65558-C3-1/2/3-R). The authors wish to thank the Sociedad Anónima Hullera Vasco-Leonesa (León, Spain), Sika (Madrid, Spain) and the Spanish Cement Institute (IECA) for their support in this research.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of ZnO on the activation of kaolinite-based coal waste: Pozzolanic activity and mineralogy in the pozzolan/lime system

  • García-Giménez, Rosario
  • Vigil de la Villa, Raquel
  • Martínez-Ramírez, S.
  • Fernández-Carrasco, Lucía
  • Frías, Moisés
One inconvenience presented by the thermal activation of kaolinite-based wastes is their low content of metakaolinite, a highly pozzolanic product listed in current standards for the manufacture of commercial cements. The addition of a chemical activator during the thermal activation process is a priority line of research to increase the reactivity of the recycled metakaolinite. In this paper, an additional chemical activator, ZnO, is studied and its effect on both pozzolanic properties and the evolution of mineralogical phases in the thermal activation of coal waste with a reaction time of up to 90 days in the pozzolan/lime system. To do so, activation temperatures of between 550 °C/650 °C were selected and additions of chemical activator (ZnO) in percentages of between 0.0% and 3.0% by weight of coal waste, because it is an activator with a positive effect on a 100% natural kaolinite. The results showed that the incorporation of ZnO inhibited the reactivity of the recycled metakaolinite and in consequence, the capacity of the metakaolinite to react with the surrounding lime; even more so when the content of added chemical activator was raised, albeit with some exceptions, in the samples activated at 550 °C and 650 °C with 0.5% of chemical activator. In none of the cases under analysis was the chemical activator able to improve the properties of the metakaolinite in comparison with the properties of the reference sample activated only with temperature. The hydrated phases that appeared in the pozzolanic reaction were tetracalcium aluminate hydrate, stratlingite, monosulfoaluminate hydrate and LDH (phyllosilicate/carbonate), The authors wish to express their gratitude and sincere appreciation to the Spanish Ministry of the Economy and Competitiveness under coordinated projects MAT2012-37005-CO3-01, BIA2015-65558-C3-1-2-3R (MINECO/FEDER) for financing this research work and grateful to the Sociedad Anónima Hullera Vasco-Leonesa (Spain) and to the Spanish Cement Institute (IECA) for their assistance with this research., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of a high content in activated carbon waste on low clinker cement microstructure and properties

  • Frías, Moisés
  • Vigil de la Villa, Raquel
  • García-Giménez, Rosario
  • Martínez-Ramírez, S.
  • Villar-Cociña, E.
  • Vegas, Iñigo
In the context of cement industry sustainability and socio-economic development, one of the primary objectives of the circular economy is the use of industrial waste as a supplementary cementitious material in the manufacture of future eco-efficient binders. This paper reports a first-time study of the effect of large proportions of the activated carbon (AC) waste used in low clinker cements on the properties and structure of the new binders. The behaviour of blended cement matrices prepared with 20%–50% AC as a pozzolan was analysed in terms of their chemical, mechanical and physical (rheology, heat of hydration, drying shrinkage, microporosity) properties. Macroporosity was also assessed with computed tomography (CT). The findings showed that these blended cements meet standard chemical and rheological requirements and that the 50% AC binder qualifies as a low heat cement. Drying shrinkage was observed to intensify with higher percentages of AC. A rise in total porosity was attendant upon pore size refinement, with an increase in the <100 nm fraction. Compressive strength declined with rising replacement ratios. Further to the CT findings, macroporosity (0.001–0.09 mm3) also increased with AC content, especially in the binders bearing 50% of the addition., This research was funded by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R) (MINECO/FEDER)). The assistance received for this study from Sociedad Anónima Hullera Vasco-Leonesa, SIKA (Madrid, Spain) and the Spanish Cement Institute (IECA) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cements based on kaolinite waste

  • García-Giménez, Rosario
  • Vigil de la Villa, Raquel
  • Frías, Moisés
  • Martínez-Ramírez, S.
  • Vegas, Íñigo
  • Fernández-Carrasco, Lucía
This article is part of the special issue “European Geosciences Union General Assembly 2018, EGU Division Energy, Resources & Environment (ERE)”. It is a result of the EGU General Assembly 2018, Vienna, Austria, 8–13 April 2018., The cement industry involves high-energy consumption that generates high CO2 emissions into the atmosphere. Environmental concerns can be addressed by replacing parts of Portland cement clinkers with pozzolanic materials in mortars and concrete. Slag, fly ash and silica fume are materials considered for the planned replacement. Research studies on clay minerals, such as kaolinite, are being followed with special attention by the scientific community and the cement industry. It is well known that these minerals require an activation process to transform kaolinite (K) into metakaolinite (MK). MK is an amorphous material from the transformation of K with high pozzolanic activity, which is its capacity to react with the portlandite released during the hydration of Portland cement, generating compounds such as C–S–H gels and some aluminum-phase hydrates. One of the MK production methods is heat treatment controlled by kaolinite at temperatures in the range of 600–900 ∘C. Different residues have been used (coal mining, paper sludge and waste from a drinking water treatment plant) activated at 600 ∘C for 2 h to elaborate blended cements. Due to their good behaviour as future eco-efficient additions, this research is a study by x-ray fluorescence (XRF), x-ray diffraction (XRD) and scanning electron microscopy (SEM) of their influence on the performances of blended cement mixtures (binary and ternary one), with substitutions of pozzolan ratio at 28 days of hydration. The porosity of pozzolanic cements decreases because of the formation of hydrated phases during pozzolanic reaction., The authors wish to express their gratitude and sincere appreciation to the Spanish Ministry of the Economy and Competitiveness under coordinated projects BIA2015-65558-C3-1-2-3R (MINECO/FEDER) for financing this research work. We are grateful to the Sociedad Anónima Hullera Vasco-Leonesa (Spain) and to the Spanish Cement Institute (IECA) for their assistance with this research., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The deterioration and environmental impact of binary cements containing thermally activated coal mining waste due to calcium leaching

  • Arribas, Idoia
  • Vegas, Iñigo
  • García, V.
  • Vigil de la Villa, Raquel
  • Martínez-Ramírez, S.
  • Frías, Moisés
Calcium-leaching processes can potentially degrade the structure of a concrete matrix. This problem is studied here through the progressive dissolution of Ca2+ in both ordinary Portland cement pastes (C-0) and binary cement blends (C-20) containing 20% thermally Activated Coal Mining Waste (ACMW).1 A series of accelerated tests are conducted that involve the immersion of these cement pastes in a 6 M ammonium nitrate solution at a temperature of 20 °C for 7 and for 21 days. A rise in paste porosity was observed, due to increased capillary pore sizes of between 5 and 0.1 μm. In the case of the 20% ACMW pastes (C-20), calcium leaching decreased, probably as a consequence of the pozzolanic effect of the ACMW, while potassium and magnesium leaching increased, due to the presence of the phyllosilicates in the ACMW. The paste compounds most affected by leaching were Ca(OH)2, C6AS3H32, and C4AH12. In general terms, it can be concluded that the incorporation of ACMW into binary cements slightly reduces the calcium leaching phenomena. Concerning the environmental impact assessment, the substitution of 20% OPC by ACMW reduced CO2 emissions by as much as 12% and improved energy efficiency by using approximately 19% fewer fossil resource, This research was developed in the framework of the MATCON Associated Unit (CSIC-Tecnalia, Madrid, Spain) with the support of the Spanish Ministry of Economy and Competitiveness (Project Ref. MAT2012-37005-CO3-01/02/03) and the European Regional Development Fund (MINECO/FEDER) (Project Ref. BIA2015-65558-C3-1,2,3-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

New developments in low clinker cement paste mineralogy

  • Frías, Moisés
  • Vigil de la Villa, Raquel
  • García-Giménez, Rosario
  • Martínez-Ramírez, S.
  • Fernández-Carrasco, Lucía
The use of industrial waste as a cement addition often changes the composition and development of the hydrated phases and with them matrix performance and durability, in particular at later ages. The effect of the presence in blended cement of 20% to 50% kaolinite based activated carbon waste (ACW) on paste hydration has been characterized by means of XRD, SEM/EDX, TG/DTG, NMR and FTIR to identify and monitor the mineralogical phases forming in materials at ages of up to 180 d. The results showed that the main reaction products forming in the first 7 d included C-S-H gels, C4ACH12 and C4AH13 (hydroxy-AFm). Whilst monocarboaluminate (Mc) content declined with rising percentages of ACW, the amount of hexagonal phase hydroxy-AFm rose. Then microstructure of the C-S-H gels developing in the OPC and the 50% additioned paste differed. Compact C-S-H gel plates, and phyllosilicate-like laminar spongy microplates with high polymerised C-S-H gel formed in the blended cement paste., This research was funded by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R) (MINECO/FEDER). The assistance received from Sociedad Anónima Hullera Vasco-Leonesa, SIKA (Madrid, Spain) and the Spanish Cement Institute (IECA) for this study is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Freeze-thaw effect on the durability of binary cements containingactivated coal-mining waste

  • García-Giménez, Rosario
  • Frías, Moisés
  • Arribas, Idoia
  • Vegas, Iñigo
  • Vigil de la Villa, Raquel
  • Rubio, Virginia
The present work contains an approach to the evaluation of binary cements prepared with a 20% substi-tution of coal-mining waste and their behaviour under a maximum of 300 freeze/thaw cycles.Mineralogical studies are conducted, as well as tests on mass variations, compressive strength, microp-orosity, the dynamic modulus of elasticity, and SEM morphologies. It is important to highlight that thepartial replacement of cement by 20% of activated coal waste, does not affect the durability against freeze/thaw cycles, since they show a fairly similar tendency to the reference mortar under extreme tempera-ture changes, This research was funded by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R) (MINECO/FEDER))., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pozzolanic reaction of a biomass waste as mineral addition to cement based saterials: studies by Nuclear Magnetic Resonance (NMR)

  • Martínez-Ramírez, S.
  • Frías, Moisés
  • Nakanishi, Erika Y.
  • Savastano Jr., Holmer
Non-fossil alternative fuels from biomass (agro-industrial, forestry and fodder plants) focus on getting cleaner, cheaper and more environmentally friendly energy sources directly related to the sustainable development of future societies. The resulting ash produced from the biomass calcination is a viable alternative for use as supplementary cementing materials in the construction industry. This study explores the scientific knowledge of calcium-silicate hydrate (C-S-H) gel formation during pozzolanic reaction between the biomass ash and calcium hydroxide through nuclear magnetic resonance technique with two different types of elephant grass ash that have different microstructure. The ash with the highest initial percentage of Q4 and Q3 units was found to react most actively and give rise to gels with the greatest inter-tetrahedral connectivity. In contrast, ash with higher content of total SiO2, exhibited lower reactivity and the C-S-H gel formed is characterised by low inter-tetrahedral connectivity from the earliest ages. Evaluation of C-S-H gel by nuclear magnetic resonance (NMR), as main hydrated phase for the engineering properties, revealed the potential of this tool to determine the effectiveness of this type of grass as raw material in cementing matrices through the evolution of the microstructure of the gel C-S-H formed., This research was financially supported by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R) (MINECO/FEDER). The authors are grateful to the Framework Agreement of Collaboration between IETcc/CSIC (Spain) and FZEA/USP (Brazil) (ref: 2013040043) and to CNPq (ref: 306386/2013-5). Finally, the authors are gratefully to the Sociedad Anónima Hullera Vasco-Leonesa, SIKA (Madrid, Spain) and the Spanish Cement Institute (IECA)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of mineral additions on the microstructure and properties of blended cement matrices for fibre-cement applications

  • Mejia-Ballesteros, Julian Eduardo
  • Holmer, Savastano Jr.
  • Fiorelli, Juliano
  • Frías, Moisés
This detailed study of the effect of three mineral additions (limestone, rice husk ash and activated coal miningwaste) differing in composition and properties explored the behaviour of blended cements with a 25% re-placement ratio. The aim was to select the optimal addition for improving the performance of naturalfibre-reinforced cements. The pozzolanic, physical and mechanical properties as well as the pore structure of theblended cement matrices were examined. Thefindings showed that although rice husk ash is characterised byhigh pozzolanicity, it had a less favourable effect on the cement than expected, yielding porous, poorly com-pacted and hence weak matrices. The activated coal mining waste showed better performance, reaching similarstrength to control mortar, better pore size refinement and an important reduction in mean pore size of 60%compared to control mortar after 60 days of curing. In light of thosefindings, this aluminosilicate addition isproposed as the most apt of the three studied for improving the quality offibre-reinforced cements, keeping inmind that the interaction effect amongst the three mineral additions was not considered in the present work, This research was funded by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R) (MINECO/FEDER)), the National Research Council’s I-COOP Programme (ref: COOPA20089-2015) and CNPq (project #306386/2013-5). The backing afforded by the Commission on In-service Training for Higher Education Personnel (CAPES) and the Framework Partnering Agreement between IETcc/CSIC (Spain) and FZEA/USP (Brazil) (ref: 2013040043) is gratefully acknowledged. Funding was also provided by FAPESP under Thematice Project #2012/51467-3., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reuse of coal mining waste to lengthen the service life of cementitious matrices

  • Caneda-Martínez, Laura
  • Frías, Moisés
  • Sánchez-Montero, Javier
  • Medina, César
  • Sánchez de Rojas, María Isabel
A chloride-induced accelerated corrosion test was conducted on steel bars embedded in mortar specimensprepared with thermally activated coal mining waste (ACMW). ACMW was observed to prompt two oppositeeffects: a delay in chloride ion penetration and a reduction in the critical chloride content needed to initiatecorrosion. Service life predictions based on thefindings revealed that adding 20% or 50% ACMW to cementimproved reinforcement corrosion resistance. Optimal results were observed for 20% replacement, in which themean reinforcement section loss was 21% lower than in OPC, Funding for this research was provided by the Spanish Ministry of the Economy and Competitiveness (MINECO) and the European Regional Development Fund (ERDF) [ref. BIA-2015-65558-C3-1,2,3-R], as well as by the Spanish Training Programme (MINECO) and the European Social Fund (ESF) [ref. BES-2016-078454]. The support received from Sociedad Anónima Hullera Vasco-Leonesa, SIKA (Madrid, Spain) and the Instituto Español del Cemento y sus Aplicaciones (IECA, Spanish cement institute) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Use of biomass-fired power plant bottom ash as an addition in new blended cements: Effect on the structure of the C-S-H gel formed during hydration

  • Sáez del Bosque, Isabel F.
  • Medina, José María
  • Frías, Moisés
  • Sánchez de Rojas, María Isabel
  • Medina, César
The identification of new supplementary cementitious materials (SCMs) for use in blended cements is an area of major interest to the scientific community. The industry is equally keen for, given the vast amounts of raw materials and emission of large volumes of greenhouse gases involved in cement manufacture, it is under pressure to reduce its environmental footprint. This study explored hydration in blended cements bearing 20 wt% bottom ash (BBA) from three biomass-fired power plants. The results showed that the OPC-BBA blended and the neat OPC pastes exhibited similar degrees of hydration (~90%) and their C-S-H gels similar Al/Si ratios (0.08–0.09), while the mean chain length of the C-S-H gels was slightly higher in the former (5.15–5.30 for blended cement vs. 4.71 for OPC). The presence of pozzolanic activity in the BBA pastes, in turn, was confirmed by their lower CH and higher C-S-H gel content than would be expected on the grounds of the dilution of the amount of cement used, This research was funded by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R and BIA2016-76643-C3-1-R) (MINECO), as well as by the Government of Extremadura and the European Regional Development Fund (ERDF) under grant GR 18122 awarded to the MATERIA research group. The authors wish to thank the Nuclear Magnetic Resonance support staff at the Madrid Institute for Materials Science (ICMM, a National Research Council body) for their assistance in conducting the 29Si MAS NMR trials., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Water transport in binary eco-cements containing coal mining waste

  • Caneda-Martínez, Laura
  • Medina, César
  • Sánchez de Rojas, María Isabel
  • Frías, Moisés
This study explores certain indirect, water transport-related durability indicators for mortars made with cement in which 20% or 50% of the ordinary portland cement (OPC) is replaced by thermally activated coal mining waste (ACMW). The valorisation of ACMW is triply beneficial, environmentally speaking, for it reduces waste stockpiling and its processing emits less CO2 and requires less fossil fuel-based energy than OPC manufacture. Its addition was observed to generate a finer pore structure and a larger volume of pores accessible to water. In mortars with 50% ACMW, pore volume rose by approximately 30%, lowering density and consequently mechanical strength. Total water absorption declined by 13% and capillary absorption by 24% in mortars with 20% ACMW, whilst no significant variations in either parameter relative to the OPC reference were found in the materials with 50% replacement ratios. Permeability to water penetration under pressure rose substantially in both blended mortars, although as the maximum and mean depth values lay within the limits specified in Spain's structural concrete code, the materials would be classified as impermeable. The mortars with 20% replacement exhibited no greater drying shrinkage than the OPC materials, whereas the mortars bearing 50% ACMW shrank by approximately 50% more than the reference., Funding for this research was provided by the Spanish Ministry of the Economy and Competitiveness (MINECO) and the European Regional Development Fund [ref. BIA-2015-65558-C3-1,2,3-R], as well as by the Spanish Training Programme (MINECO) and the European Social Fund [ref. BES-2016-078454]. The support received from the Instituto Español del Cemento y sus Aplicaciones (IECA, Spanish cement institute), SIKA (Madrid, Spain) and Sociedad Anónima Hullera Vasco-Leonesa is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design and properties of eco-friendly binary mortars containing ash from biomass-fuelled power plants

  • Medina, José María
  • Sáez del Bosque, Isabel F.
  • Frías, Moisés
  • Sánchez de Rojas, María Isabel
  • Medina, César
The use of biomass to produce electric power and heat will intensify in the years to come, in pursuit of sustainable growth. Stockpiling the vast amounts of fly and bottom ash generated in that process wastes resources and has an adverse impact on the environment. The viability of bottom ash as a supplementary cementitious material in new eco-efficient cements is studied, including its effect on binder chemical, rheological, mechanical and microstructural properties. The findings show that these additions induce improvements in later age mechanical performance relative to conventional mortars. An ANOVA conducted to determine the impact of waste type, replacement ratio and curing time on compressive and flexural strength reveals that the latter two have a significant effect on mechanical properties. The new cements meet the requirements laid down in EN 197-1 for CEM II/A and CEM IV/A cements, making them apt for use in construction., This research was funded by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R and BIA2016-76643-C3-1-R) (MINECO/FEDER), as well as by the Government of Extremadura and the European Regional Development Fund (ERDF) under grant GR 18122 awarded to the MATERIA research group., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exploring sulphate resistance of coal mining waste blended cements through experiments and thermodynamic modelling

  • Caneda-Martínez, Laura
  • Kunther, Wolfgang
  • Medina, César
  • Sánchez de Rojas, María Isabel
  • Frías, Moisés
This study evaluates the sulphate resistance of blended cement derived from the addition of thermally activated coal waste as pozzolan, at replacement levels of 0%, 20% (CMW20) and 50% (CMW50) with a multi-method approach. The pastes were prepared at a w/b ratio of 0.5, using a water-reducing admixture in the blended pastes to compensate for their high water demand. Sulphate resistance is reduced in CMW20 pastes, while longterm benefits are observed for CMW50 pastes, although moderate signs of deterioration are observed at the beginning of the exposure. The initial damage in CMW50 pastes is attributable to the precipitation of products (mainly ettringite and monosulphoaluminate) in the small capillary pores (<0.01 ¿m). This is prevented in OPC and CMW20 pastes since their microstructure allow the precipitation in the macropores (>0.05 ¿m). The greater long-term resistance of CMW50 pastes was explained by thermodynamic calculations, which suggests that the lower calcium leachability of these cements prevented gypsum formation. This, together with the higher content of carboaluminate phases, leads to lower supersaturation levels in the pore solution with respect to ettringite, reducing stresses derived from sulphate exposure., This work was supported by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund (MINECO/FEDER) [grant number BIA-2015-65558-C3-1,2,3-R] and as well as by the Spanish Training Program, and the European Social Fund (MINECO/FSE) [grant number BES-2016-078454]. The authors are also grateful to the Sociedad An´onima Hullera Vasco-Leonesa, SIKA (Madrid, Spain), the Spanish Cement Institute (IECA) and the Scientific Research Support Services of the University of A Coru˜na for their assistance. The sample preparation of the SEM samples by A. M. Rzepkiewicz-Hansen is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the fiber treatment and matrix modification on the durability of eucalyptus fiber reinforced composites

  • Mejia-Ballesteros, Julian Eduardo
  • Rodier, L.
  • Filomeno, R.
  • Savastano, H.
  • Frías, Moisés
  • Fiorelli, Juliano
It is well known that the most important issue of cement-based composites is the durability of the natural fibers. The present study evaluates the effect of activated coal mining residues on the physical-mechanical properties of fiber cement composites reinforced by thermally treated eucalyptus pulp, before and after accelerated aging. The results showed that the partial substitution of cement by activated coal mining residues and the use of thermally treated fibers contribute to the improvement of the mechanical properties of the composites. Indeed, an increase of the values of the modulus of rupture (MOR) and the specific energy (SE) of the composites is observed under four-point bending flexural tests. Moreover, after accelerated aging tests, both fiber treatment and matrix modification contribute to mitigate the degradation of the fibers and increase the mechanical properties of the composites. According to the results of the study, the use of activated coal mining residues as partial substitution of cement and hornification treatment of the pulp, can lead to the improvement of the mechanical performanceand durability of fiber cement composites., The authors were supported by grants offered by Susano PapelCelulose S.A., Brazil. The authors are also grateful to Coordination of Improvement of Higher Education Personnel – CAPES (Cod. 001) and the Framework Partnering Agreement between IETcc/CSIC (Spain) and FZEA/USP (Brazil) (BDC 20195707/ACAM 2019040029). This research was funded by the Spanish Ministry of Economy and Competitiveness (BIA2015-65558-C3-1-2-3R) (MINECO/FEDER)) and the National Research Council’s I–COOP Programme (ref: COOPA20089- 2015).
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

New developments in low clinker cement paste mineralogy

  • Frias Rojas, Moisés
  • Vigil de la Villa, Raquel
  • Garcia, Rosario
  • Martínez Ramírez, Sagrario
  • Fernández Carrasco, Lucía|||0000-0002-2379-3782
The use of industrial waste as a cement addition often changes the composition and development of the hydrated phases and with them matrix performance and durability, in particular at later ages. The effect of the presence in blended cement of 20% to 50% kaolinite based activated carbon waste (ACW) on paste hydration has been characterized by means of XRD, SEM/EDX, TG/DTG, NMR and FTIR to identify and monitor the mineralogical phases forming in materials at ages of up to 180 d. The results showed that the main reaction products forming in the first 7 d included C-S-H gels, C4ACH12 and C4AH13 (hydroxy-AFm). Whilst monocarboaluminate (Mc) content declined with rising percentages of ACW, the amount of hexagonal phase hydroxy-AFm rose. Then microstructure of the C-S-H gels developing in the OPC and the 50% additioned paste differed. Compact C-S-H gel plates, and phyllosilicate-like laminar spongy microplates with high polymerised C-S-H gel formed in the blended cement paste., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

New developments in low clinker cement paste mineralogy

  • Frias Rojas, Moisés
  • Vigil de la Villa, Raquel
  • Garcia, Rosario
  • Martínez Ramírez, Sagrario
  • Fernández Carrasco, Lucía
The use of industrial waste as a cement addition often changes the composition and development of the hydrated phases and with them matrix performance and durability, in particular at later ages. The effect of the presence in blended cement of 20% to 50% kaolinite based activated carbon waste (ACW) on paste hydration has been characterized by means of XRD, SEM/EDX, TG/DTG, NMR and FTIR to identify and monitor the mineralogical phases forming in materials at ages of up to 180 d. The results showed that the main reaction products forming in the first 7 d included C-S-H gels, C4ACH12 and C4AH13 (hydroxy-AFm). Whilst monocarboaluminate (Mc) content declined with rising percentages of ACW, the amount of hexagonal phase hydroxy-AFm rose. Then microstructure of the C-S-H gels developing in the OPC and the 50% additioned paste differed. Compact C-S-H gel plates, and phyllosilicate-like laminar spongy microplates with high polymerised C-S-H gel formed in the blended cement paste., Peer Reviewed, Postprint (author's final draft)