Pasar al contenido principal

FABRICACION ADITIVA DE COMPUESTOS METAL-CERAMICA Y RECUBRIMIENTOS AVANZADOS A PARTIR DE SUSPENSIONES COLOIDALES

PID2019-106631GB-C42

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exploitation of Lignocellulose Fiber-Based Biotemplates to Improve the Performance of an Immobilized TiO2 Photocatalyst

  • González Granados, Zoilo
  • Yus, Joaquín
  • Bravo, Yessica
  • Sánchez-Herencia, A. Javier
  • Ferrari, Begoña
The performance of an immobilized photocatalyst has been successfully improved by colloidal processing of a heterostructure composed by TiO<sub>2</sub> nanoparticles and lignocellulose nanofibers (LCNFs) obtained from biomass residues. The incorporation of 4 wt.% of biotemplate to the formulation increased the degradation rate and reduced the operating time to remove the 100% of methyl orange of a liquid solution. The reaction rate constant (<i>k</i> = 0.29–0.45 h<sup>−1</sup>) of the prepared photocatalytic coatings (using commercial particles and templates obtained from natural-derived resources) are competitive with other pure TiO<sub>2</sub> materials (no composites), which were prepared through more complex methodologies. The optimization stages of deposition and sintering processes allowed us to obtain homogeneous and crack-free microstructures with controlled thickness and mass values ranging from 3 to 12 µm and 0.9 to 5.6 mg, respectively. The variation of the microstructures was achieved by varying the amount of LCNF in the formulated suspensions. The versatility of the proposed methodology would allow for implementation over the internal surface of photocatalytic reactors or as a photocatalytic layer of their membranes. In addition, the processing strategy could be applied to immobilize other synthetized semiconductors with higher intrinsic photocatalysis properties., This research was supported by the projects S2018/NMT-4411 (Comunidad de Madrid) and PID2019-106631GB-C42 (MINECO/FEDER). Z. Gonzalez acknowledges the Spanish Ministry of Economy and Competitiveness for the Postdoctoral Fellowship: IJCI-2016-28538., This work was supported by FCT-Fundação para a Ciência e a Tecnologia (project PEst-OE/QUI/UI0674/2019, CQM, Portuguese government funds), through the Madeira 14–20 Program, project PROEQUIPRAM Reforço do Investimento em Equipamentos e Infraestruturas Científicas na RAM (M1420-01-0145-FEDER-000008) by ARDITI-Agência Regional para o Desenvolvimento da Investigação Tecnologia e Inovação, through project M1420-01-0145-FEDER-000005—Centro de Química da Madeira CQM + (Madeira 14–20). SM was supported by the postdoctoral fellowship granted by ARDITI CQM + project (ARDITI-CQM/2017/008-PDG). RP was supported by an FCT postdoctoral grant (SFRH/BPD/97387/2013)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Colloidal processing and sintering of WC-based ceramics with low Ni content as sintering aid

  • García Ayala, Esperanza Macarena
  • Silvestroni, L.
  • Yus, Joaquín
  • Ferrari, Begoña
  • Pastor, J.Y.
  • Sánchez-Herencia, A. Javier
To soften the extreme sintering conditions of Tungsten Carbide (WC), a 3 wt.% of metallic nickel (Ni) was added to the starting powders. To ensure a fair distribution of the second phase and an intimate mixture of the phases, the colloidal process was adopted. A commercial Ni and a in-house synthesised nanosized nickel were used as sintering aids. Rheological studies allowed a high dispersion of the nickel in the final composite powders. Sintering studies by Hot-Pressing route (HP) proved the great benefices of Ni as a sintering aid, decreasing the maximum temperature necessary to achieve full densification, from 1900 to 1450 °C and dwell times from 20 to 7 min. Among all the materials obtained, the best results in terms of density, microstructure and properties were obtained for WC-nNi, which achieved hardness of 14.8 GPa and toughness comparable to conventional cermets with much higher content of metallic phase., This work has been supported by the Spanish Government under contracts PID2019-106631GB-C42 and C44 (MICINN/FEDER, UE) and Madrid Regional Government under contract P2018/NMT-4411 (Comunidad de Madrid/FEDER, UE). Mrs. García-Ayala thanks MINECO/FEDER, UE by grant BES-2016-079038 and JECS Trust for a mobility grant (ref: 2018170) for three months to ISTEC. Authors thank A. Sangiorgi for advice and support running the HP cycles.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

  • Zegai, Ahmed-Ameur
  • Besharatloo, Hossein
  • Ortega-Columbrans, Pablo
  • Djerdjare, Boubekeur
  • Ferrari, Begoña
  • Sánchez-Herencia, A. Javier
This study investigates the sintering behaviour and properties of WC-based composites in which WC was mixed with W5vol%Ni in concentrations of 10vol% and 20vol%. Colloidal processing in water and spark plasma sintering were employed to disperse the WC particles and facilitate sintering. The addition of W5vol%Ni improved the sintering process, as evident from a lower onset temperature of shrinkage determined through dilatometric studies. All samples exhibited the formation of tungsten monocarbide (W2C), with a more pronounced presence in the WC/20(W5vol%Ni) composite. Sintering reached its maximum rate at 1550 °C and was completed at 1600 °C, resulting in a final density exceeding 99.8%. X-ray diffraction analysis confirmed the detection of WC and W2C phases after sintering. The observed WC content was higher than expected, which may be attributed to carbon diffusion during the process. Macro-scale mechanical characterisations revealed that the WC/10(W5vol%Ni) composite exhibited a hardness of 18.9 GPa, while the WC/20(W5vol%Ni) composite demonstrated a hardness of 18.3 GPa. Increasing the W5vol%Ni binder content caused a decrease in mechanical properties due to the formation of W2C phases. This study provides valuable insights into the sintering behavior and properties of WC/W5vol%Ni composites, offering potential applications in extreme environments., This research was supported by the Spanish Government through the projects PID2019–106631GB-C41/C42 and TED2021-129920B-C41 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Processing of membranes and 3D scaffolds based on n-TiO2 colloidally dispersed on a thermoplastic matrix for photocatalytic pollutant removal

  • Ortega-Columbrans, Pablo
  • Ferrández-Montero, Ana
  • Yus, Joaquín
  • Sánchez-Herencia, A. Javier
  • Ferrari, Begoña
[EN] One of the most promising technologies for water treatment today is photocatalytic membrane reactors (PMRs). Manufacturing efficient membranes is still challenging as many factors are involved, like the porosity, specific surface area, nature and size of particles. In this work, a colloidal method to self-support commercial nanoparticles (n-TiO) in a polymeric matrix of polylactic acid (PLA) is proposed allowing the fabrication of 2D and 3D structures with high inorganic content that can be adapted to the PMR configurations. Using a commercial filament of PLA loaded with up to 15 vol% of n-TiO2 as starting point, photocatalytic membranes have been manufactured by FFF. In addition, following a similar process, tapes with n-TiO2 particles up to 15 vol% have been processed by tape casting. Thermal characterisation (DTA) and dynamic rheometry evaluated the commercial filament for printing to determine the conditions used during the thermal extrusion and printing processes. FTIR and XRD technologies were used to determine the chemical interactions of PLA matrices with TiO nanoparticles. Porosity was measured by Archimedes's method for the filaments, by mercury intrusion for the membranes and by optical microscopy for the scaffolds. Finally, the microstructure of the 2D and 3D pieces was evaluated by scanning microscopy. 2D tape cast membranes were compared with individual filaments and 3D printed scaffolds in linear and gyroidal geometries. The catalytic activity results indicate that tape cast membranes show much higher kinetic constants than the individual filaments and the linear and gyroidal scaffolds. Regarding the two different printed scaffolds, in contrast to the kinetic values, gyroidal geometries achieve an average degradation time (t) of 6.1 h, which is a lower value than those observed for linear scaffold geometries. Methyl orange degradation tests after 24 h exposure under UV light showed degradation rates of 98% for membranes, 90% for commercial filaments, 80% for gyroidal scaffolds and 60% for linear patterns. Therefore, these results are promising as a solution for fabricating easily extractable self-supported membranes for water treatment in PMRs., This work has been supported by the Spanish Government (Agencia Estatal de Investigación) through the projects PID2019–106631 GB-C42 (MICRO@Mater) and TED2021–129920B-C41 (EC0FOOTPrint), both cofunded by AEI/10.13039/501100011033/Uni´on Europea NextGenerationEU/PRTR). Pablo Ortega Columbrans acknowledges the Comunidad de Madrid for the industrial doctorate support through the contract IND2022/IND-23603.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Material thermal extrusion of conductive 3D electrodes using highly loaded graphene and graphite colloidal feedstock

  • Urra Sánchez, Oxel
  • Besharatloo, Hossein
  • Yus, Joaquín
  • Sánchez-Herencia, A. Javier
  • Ferrari, Begoña
[EN] Evolution in the energy storage field requires the development of more sustainable and efficient high-performance electrochemical storage devices (EESDs). Additive manufacturing (AM) opens unique opportunities to improve the efficiency and the electrochemical response by the design of 3D electrodes and the increasing of exposed active surface area impossible to achieve by other processing techniques. In other to reach high-performance EESDs, carbonaceous species are well-established as electroactive materials owing to their electronic properties, low cost, and sustainable origin. Although the materials have been widely investigated, there is a lack of feedstock development for the fabrication of EESDs by AM technologies. This work presents the fabrication of metals free light conductive filaments for material thermal extrusion (MTE) by formulating PLA-based composites with a high content of colloidal graphite and graphene (15–25 vol%). By the colloidal characterization and surface modification of the carbonaceous species, an improved distribution and enhanced platelet/polymer bond were achieved, provoking the inorganic phase's orientation during the extrusion process. Prepared filaments were characterized to analyze the influence of the microstructural anisotropy on thermal, thermorheological, mechanical, and electrical properties. Subsequently, developed filaments were used to print complex electrodes by MTE, enhancing the electrochemical properties of the electrodes with superior control of the macrostructural design. The developed colloidal filaments with an oriented inorganic microstructure, not only allow a defined shaping of the outer structure of the electrodes but also let the design of completely different microstructures. Consequently, different microstructural configurations were printed increasing the number of conduction paths in the polymeric matrix to achieve high electric conductivities (22 S.m) in printed electrodes., This work has been supported by the Spanish Government (Agencia Estatal de Investigacion) ´ through the projects PID2019-106631GB-C42 (AEI/10.13039/501100011033) and the Regional Government of Madrid through the program ADITIMAT, ref. P2018/NMT-4411, both cofounded by the European Regional Development Fund (FEDER/ ERDF). H. Besharatloo acknowledge the Spanish Government for its postdoctoral support through Margarita Salas grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reaction behavior during Spark Plasma Sintering of cBN-TiCN-Ni powders

  • Mineiro, Ricardo
  • Fernandes, C.M.
  • Silva, E.L.
  • Soares, M.R.
  • Figueiredo, D.
  • Ferrari, Begoña
  • Sánchez-Herencia, A. Javier
  • Senos, A.M.R.
[EN] Polycrystalline cubic boron nitride (PcBN) is the designation given to composites constituted by cBN hard particles within a ceramic/metallic matrix. These composites are normally processed in severe pressure and temperature conditions to achieve full densification and prevent hexagonal BN formation, which would decrease the composite hardness. In this work, the Spark Plasma Sintering (SPS) technique was investigated as an alternative to sinter cBN-TiCN based composites, with and without addition of metallic Ni. The initial compositions were selected according with calculated phase diagrams, using the Thermo-calc software. The thermal behavior during SPS was studied up to 2000°C, namely the densification, reactivity and phase transformations. A larger densification was achieved with Ni addition, but full removal of open porosity was only possible at 1700 °C, where the cBN phase transformation to hBN completely occurred. In agreement with the thermodynamic calculations, other matrix phases, as TiB2 and Ni3B, were formed during sintering., This research is sponsored by FEDER funds through COMPETE, Programa Operacional Factores de Competividade, 3DCompcer (POCI-01-0247-FEDER-047060). The authors are grateful to the JECS Trust for funding this work between the Department of Materials and Ceramic Engineering, University of Aveiro (Portugal), and the Institute of Ceramic and Glass (ICV-CSIC) (Spain) (Contract No. 2020257). This work was developed within the scope of the project CICECO-Aveiro Institute of Materials, UIDB/50011/2020, UIDP/50011/2020 & LA/P/0006/2020, financed by national funds through the FCT/MCTES (PIDDAC) and also within PID2019-106631GB-C42 of the Spanish Government., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Lateral Laser-Cladding Process on the Corrosion Performance of Inconel 625

  • Rezayat, Mohammad
  • Sani, Amirhossein Aboutorabi
  • Noghani, Mohammad Talafi
  • Saghafi Yazdi, Morteza
  • Taheri, Morteza
  • Moghanian, Amirhossein
  • Mohammadi, Mohammad Abedini
  • Moradi, Mahmoud
  • Mateo García, Antonio Manuel
  • Besharatloo, Hossein
[EN] This study aimed to evaluate the corrosion properties of different samples coated by the laser-cladding method to find the optimal laser parameters. Thereby, potentiodynamic polarization (Tafel) and electrochemical impedance tests were performed to assess the corrosion resistance of coated samples. Consequently, the corrosion morphology of tested samples was inspected by scanning electron microscopy. The results demonstrated that the laser power directly correlates with pitting corrosion and defects on the surface of the samples. Moreover, when molybdenum and chromium ions are increased in the electrolyte solution, the passive and protective layers are more durable, as the ions are sited within the holes and defects, reducing the surface corrosion rate., This research was funded by Financial support from the Spanish Government (Agencia Estatal de Investigación) grant number PID2019-106631GB-C41/C42 and PGC2018-096855-B-C41. And The APC was funded by Regional Government of Madrid through the program ADITIMAT (S2018/NMT-4411), Spanish Government for its postdoctoral support (Margarita Salas 2022) and AGAUR, Agency for Administration of University and Research (Agència de Gestió d’Ajuts Universitaris i de Recerca) (2021 SGR 01053)., Peer reviewed
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Micropillar compression of Ti(C,N)-FeNi cermets: Microstructural, processing, and scale effects

  • Besharatloo, Hossein
  • de Nicolás Morillas, M.
  • Chen, Ming
  • Mateo, A.
  • Ferrari, Begoña
  • Gordo, Elena
  • Jiménez Piqué, Emilio
  • Wheeler, Jeff
  • Llanes, Luis
The influence of microstructure and processing route on the small-scale mechanical response as well as on the deformation and failure mechanisms of Ti(C,N)-FeNi cermets were investigated by uniaxial compression of micropillars milled by focused ion beam with different sizes. Stress-strain curves were determined and associated deformation mechanisms were observed in-situ using scanning electron microscopy. The appropriate micropillars dimension was assessed, based on the microstructural characteristics of studied cermets, to overcome scale effect issues. A direct relationship was observed between yield strength and ceramic/metal ratio for colloidal samples. Meanwhile, deformation of metallic binder and glide between Ti(C,N)/Ti(C,N) particles were evidenced as dominant mechanisms during the compression for colloidal cermets with 70 and 80 vol% of ceramic phase, respectively. The obtained results illustrate that samples processed from powder attained by colloidal route provide superior mechanical behavior, as compared to that exhibited by specimens shaped following a conventional powder metallurgy one (wet ball-milling/drying)., 8 páginas