Pasar al contenido principal

MEJORA DEL RENDIMIENTO (CORROSION E INTEGRIDAD MECANICA) DE SUSTRATOS DE MATERIALES DUROS MEDIANTE RECUBRIMEINTOS PVD ALCRSIN E IMPLANTACION DE IONES

PGC2018-096855-B-C41

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Generación de Conocimiento y Fortalecimiento Científico y Tecnológico del Sistema de I+D+i
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Micropillar compression of Ti(C,N)-FeNi cermets: Microstructural, processing, and scale effects

  • Besharatloo, Hossein
  • de Nicolás Morillas, M.
  • Chen, Ming
  • Mateo, A.
  • Ferrari, Begoña
  • Gordo, Elena
  • Jiménez Piqué, Emilio
  • Wheeler, Jeff
  • Llanes, Luis
The influence of microstructure and processing route on the small-scale mechanical response as well as on the deformation and failure mechanisms of Ti(C,N)-FeNi cermets were investigated by uniaxial compression of micropillars milled by focused ion beam with different sizes. Stress-strain curves were determined and associated deformation mechanisms were observed in-situ using scanning electron microscopy. The appropriate micropillars dimension was assessed, based on the microstructural characteristics of studied cermets, to overcome scale effect issues. A direct relationship was observed between yield strength and ceramic/metal ratio for colloidal samples. Meanwhile, deformation of metallic binder and glide between Ti(C,N)/Ti(C,N) particles were evidenced as dominant mechanisms during the compression for colloidal cermets with 70 and 80 vol% of ceramic phase, respectively. The obtained results illustrate that samples processed from powder attained by colloidal route provide superior mechanical behavior, as compared to that exhibited by specimens shaped following a conventional powder metallurgy one (wet ball-milling/drying)., 8 páginas
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct-methane anode-supported solid oxide fuel cells fabricated by aqueous gel-casting

  • Morales, Miguel
  • Laguna-Bercero, M. A.
  • Jiménez-Piqué, Emilio
Direct methane Solid Oxide Fuel Cells (SOFCs) operated under catalytic partial oxidation (CPOX) conditions are investigated, focusing on the processing of the anode support and the anode deactivation caused by carbon deposition. Anode-supported SOFCs based on gadolinium-doped ceria (GDC) electrolyte, and NiO-GDC anode support were fabricated by the gel-casting method. Suitable aqueous slurries formulations of NiO–GDC were prepared, starting NiO-GDC nanocomposite powders, agarose as gelling agent and rice starch as pore former. Electrochemical and mechanical tests evidenced that the support of 550 ± 50 µm thickness and 10 wt% pore former is a good candidate for direct-methane SOFCs. The cells operating under stoichiometric conditions of CPOX reached a performance of 0.64 W·cm−2 at 650 ºC, a very close value to that measured under humidified hydrogen (0.71 W·cm−2). The best electrochemical stability of the cell is achieved at a CH4/O2 ratio of 2.5, showing no evidence of carbon deposition and reducing nickel re-oxidation significantly., This research has received funding from grants PGC2018-096855-B-C41 and PID2019-107106RB-C32 funded by MCIN/AEI/10.13039/501100011033. Miguel Morales Comas is a Serra Húnter Fellow (Generalitat de Catalunya)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Micromechanical mapping of polycrystalline cubic boron nitride composites by means of high-speed nanoindentation: Assessment of microstructural assemblage effects

  • Gordon, S.
  • Besharatloo, Hossein
  • Wheeler, J.M.
  • Rodriguez-Suarez, T.
  • Roa, J.J.
  • Jiménez-Piqué, Emilio
  • Llanes, L.
[EN] Polycrystalline cubic boron nitrides (PcBNs) are composites widely used as cutting tool materials due to their exceptional high hardness and wear resistance. Investigation of their micromechanical properties is key for optimizing PcBN’s performance through microstructural design. Within this context, high-speed nanoindentation is proposed and implemented, for three different PcBN grades, to correlate microstructure with local mechanical properties. A total of 40,000 imprints were performed in each grade. The obtained mechanical maps and data sets are statistically treated following two deconvolution approaches: 1D and 2D Gaussian fitting. The use of high-speed nanoindentation is validated not only by the reliable assessment of the intrinsic mechanical properties of cBN particles, binder and interphase region, but also by the successful mirroring of microstructural assemblage within the mechanical maps attained. Comparison of the results determined from 1D and 2D gaussian representations are in satisfactory agreement. Nevertheless, some difficulties and disparity between them arises when involving fine-grained microstructures., Work was supported by the Spanish Ministerio de Ciencia, Innovación y Universidades MICINN - FEDER (Spain) through grants PGC2018-096855-B-C41 and PID2019-106631GB-C41 (AEI/10.13039/501100011033), as well as by the industry-university collaborative program among Element Six, Seco Tools and UPC., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Micropillar compression of Ti(C,N)-FeNi cermets: Microstructural, processing, and scale effects

  • Besharatloo, Hossein
  • Nicolás-Morillas, M. de
  • Chen, M.
  • Mateo, A.
  • Ferrari, Begoña
  • Gordo Odériz, Elena
  • Jiménez-Piqué, Emilio
  • Wheeler, J.M.
  • Llanes, L.
[EN] The influence of microstructure and processing route on the small-scale mechanical response as well as on the deformation and failure mechanisms of Ti(C,N)-FeNi cermets were investigated by uniaxial compression of micropillars milled by focused ion beam with different sizes. Stress-strain curves were determined and associated deformation mechanisms were observed in-situ using scanning electron microscopy. The appropriate micropillars dimension was assessed, based on the microstructural characteristics of studied cermets, to overcome scale effect issues. A direct relationship was observed between yield strength and ceramic/metal ratio for colloidal samples. Meanwhile, deformation of metallic binder and glide between Ti(C,N)/Ti(C,N) particles were evidenced as dominant mechanisms during the compression for colloidal cermets with 70 and 80 vol% of ceramic phase, respectively. The obtained results illustrate that samples processed from powder attained by colloidal route provide superior mechanical behavior, as compared to that exhibited by specimens shaped following a conventional powder metallurgy one (wet ball-milling/drying)., The authors want to acknowledge the financial support from the Spanish Government (Agencia Estatal de Investigación) through the projects PID2019–106631GB-C41/C42/C43 (AEI/10.13039/501100011033) and PGC2018–096855-B-C41, Fondo Europeo de Desarrollo Regional (FEDER) and the Regional Government of Madrid through the program ADITIMAT, ref. P2018/NMT-4411. H. Besharatloo and M. de Nicolás-Morillas acknowledge the Spanish Government for its postdoctoral support through Margarita Salas grants. Finally, the authors would like to thank Dr. Miguel de Dios for his efforts as one of the experts who helped colloidal processing to become functional for new cermets., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Lateral Laser-Cladding Process on the Corrosion Performance of Inconel 625

  • Rezayat, Mohammad
  • Sani, Amirhossein Aboutorabi
  • Noghani, Mohammad Talafi
  • Saghafi Yazdi, Morteza
  • Taheri, Morteza
  • Moghanian, Amirhossein
  • Mohammadi, Mohammad Abedini
  • Moradi, Mahmoud
  • Mateo García, Antonio Manuel
  • Besharatloo, Hossein
[EN] This study aimed to evaluate the corrosion properties of different samples coated by the laser-cladding method to find the optimal laser parameters. Thereby, potentiodynamic polarization (Tafel) and electrochemical impedance tests were performed to assess the corrosion resistance of coated samples. Consequently, the corrosion morphology of tested samples was inspected by scanning electron microscopy. The results demonstrated that the laser power directly correlates with pitting corrosion and defects on the surface of the samples. Moreover, when molybdenum and chromium ions are increased in the electrolyte solution, the passive and protective layers are more durable, as the ions are sited within the holes and defects, reducing the surface corrosion rate., This research was funded by Financial support from the Spanish Government (Agencia Estatal de Investigación) grant number PID2019-106631GB-C41/C42 and PGC2018-096855-B-C41. And The APC was funded by Regional Government of Madrid through the program ADITIMAT (S2018/NMT-4411), Spanish Government for its postdoctoral support (Margarita Salas 2022) and AGAUR, Agency for Administration of University and Research (Agència de Gestió d’Ajuts Universitaris i de Recerca) (2021 SGR 01053)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Direct-methane anode-supported solid oxide fuel cells fabricated by aqueous gel-casting

  • Morales, M.
  • Laguna-Bercero, M.A.
  • Jiménez-Piqué, E.
Direct methane Solid Oxide Fuel Cells (SOFCs) operated under catalytic partial oxidation (CPOX) conditions are investigated, focusing on the processing of the anode support and the anode deactivation caused by carbon deposition. Anode-supported SOFCs based on gadolinium-doped ceria (GDC) electrolyte, and NiO-GDC anode support were fabricated by the gel-casting method. Suitable aqueous slurries formulations of NiO–GDC were prepared, starting NiO-GDC nanocomposite powders, agarose as gelling agent and rice starch as pore former. Electrochemical and mechanical tests evidenced that the support of 550 ± 50 µm thickness and 10 wt% pore former is a good candidate for direct-methane SOFCs. The cells operating under stoichiometric conditions of CPOX reached a performance of 0.64 W·cm−2 at 650 ºC, a very close value to that measured under humidified hydrogen (0.71 W·cm−2). The best electrochemical stability of the cell is achieved at a CH4/O2 ratio of 2.5, showing no evidence of carbon deposition and reducing nickel re-oxidation significantly.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Comparative study of mechanical performance of AlCrSiN coating deposited on WC-Co and cBN hard substrates

  • Liang, Jing
  • Serra, Marc
  • Gordon, Sandra
  • Fernández de Ara, Jonathan
  • Almandoz Sánchez, Eluxka
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
The objective of this study is to explore and compare the mechanical response of AlCrSiN coatings deposited on two different substrates, namely, WC-Co and cBN. Nano-indentation was used to measure the hardness and elastic modulus of the coatings, and micro-indentation was used for observing the contact damage under Hertzian contact with monotonic and cyclic (fatigue) loads. Microscratch and contact damage tests were also used to evaluate the strength of adhesion between the AlCrSiN coatings and the two substrates under progressive and constant loads, respectively. The surface damages induced via different mechanical tests were observed using scanning electron microscopy (SEM). A focused ion beam (FIB) was used to produce a cross-section of the coating–substrate system in order to further detect the mode and extent of failure that was induced. The results show that the AlCrSiN coating deposited on the WC-Co substrate performed better in regard to adhesion strength and contact damage response than the same coating deposited on the cBN substrate; this is attributed to the lower plasticity of the cBN substrate as well as its less powerful adhesion to the coating., This research was funded by The Spanish Ministry of Science, Innovation and Universities through grants PGC2018-096855-B-C41, PGC2018-096855-A-C44 and PID2021-126614OB-100.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Improved adhesion of cathodic arc PVD AlCrSiN coating on ion-implanted WC-Co substrates

  • Ortiz Membrado, Laia
  • García-González, Sandra
  • Orrit-Prat, Jordi
  • Bonet, Raül
  • Caro, Jaume
  • Fernández de Ara, Jonathan
  • Almandoz Sánchez, Eluxka
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
Ion implantation has been shown to improve adhesion strength of AlCrSiN coatings due to a synergic enhancement on fracture toughness and load bearing capability of the substrate that can potentially increase the in-service efficiency of coated cutting tools. In this work, AlCrSiN coatings deposited by PVD on WC-Co substrates implanted with Ti, Cr and N ion species have been processed. The mechanical properties and adhesion have been characterized by contact techniques and the residual stress of the coatings and substrates have been evaluated using FIB-DIC technique and Vickers indentation tests, respectively. An improvement of adhesion strength is obtained for treated substrates, especially for those implanted with titanium and chromium ions. This improvement is attributed to the introduction of residual stresses in the substrate, which increases its fracture toughness and enhances its load bearing capability., Work funded through The Spanish Ministry of Science, Innovation and Universities through grants PGC-2018-096855-B-C41, PGC-2018-096855-B-C42 and PGC-2018-096855-A-C44
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Mechanical performance of AlCrSiN and AlTiSiN coatings on inconel and steel substrates after thermal treatments

  • Liang, Jing
  • Almandoz Sánchez, Eluxka
  • Ortiz Membrado, Laia
  • Rodríguez Lozano, Rafael
  • Fernández de Ara, Jonathan
  • García Fuentes, Gonzalo
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
The objective of this study was to explore the mechanical properties of AlCrSiN and AlTiSiN coatings deposited on Inconel and steel substrates after thermal treatments of 500 °C and 800 °C. Nanoindentation was used to measure the hardness and elastic modulus of the coatings, and microindentation was used for observing the contact damage with Hertzian contact loadings. Microscratch and Mercedes tests were used to evaluate the adhesive strength between coating and substrate with both progressive and static loads, respectively. The surface damage was inspected by optical microscopy and scanning electron microscopy (SEM). Focus ion beams (FIB) were used to mill the cross-sections in order to detect the extent and mode of failure. The results show that AlCrSiN coatings and Inconel substrates exhibit better mechanical performance, even after thermal treatments., The authors acknowledge the support from the Spanish ministry of Science, Innovation and Universities through grants PGC2018-096855-B-C41 and PGC2018-096855-A-C44.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Assessment of the mechanical performance of AlCrSiN coating implanted with Zr and Ta ions

  • Liang, Jing
  • Ortiz Membrado, Laia
  • Bonet, Raül
  • Orrit-Prat, Jordi
  • Caro, Jaume
  • Fernández de Ara, Jonathan
  • Almandoz Sánchez, Eluxka
  • Ruan, Qingdong
  • King-Yu Fu, Ricky
  • Chu, Paul K.
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
This study explores the impact of Zr and Ta ion implantation on the mechanical performance of an AlCrSiN quaternary coating deposited on a WC-Co cermet substrate. Nanoindentation tests revealed a decrease in hardness and elastic modulus after ion implantation, compared to unimplanted coatings. Moreover, microscratch and contact damage tests demonstrated improved adhesion and reduced surface damage for ion-implanted samples, with Ta implantation exhibiting the best performance. Scanning Electron Microscopy (SEM) and focused ion beam (FIB) cross-sectional analysis confirmed less severe damage in ion-implanted samples compared to unimplanted ones. These findings suggest that Zr/Ta ion implantation enhances the structural integrity and adhesion of AlCrSiN coatings under loading conditions commonly encountered in practical applications, despite a moderate reduction in intrinsic hardness and elastic modulus., The work was funded by the Spanish Ministry of Science, Innovation, and Universities through grants PGC2018-096855-B-C41, PGC2018-096855-B-C43, and PGC2018-096855-A-C44