Pasar al contenido principal

MEJORA DEL RENDIMIENTO (CORROSION E INTEGRIDAD MECANICA) DE SUSTRATOS DE MATERIALES DUROS MEDIANTE RECUBRIMIENTOS PVD ALCRSIN E IMPLANTACION IONICA

PGC2018-096855-A-C44

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Generación de Conocimiento y Fortalecimiento Científico y Tecnológico del Sistema de I+D+i
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario ASOC. DE LA INDUSTRIA NAVARRA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Influence of microstructural assemblage of the substrate on the adhesion strength of coated PcBN grades

  • Gordon Pozuelo, Sandra|||0000-0001-9131-9559
  • Roa Rovira, Joan Josep|||0000-0002-7440-0766
  • Rodríguez Suárez, Teresa
  • M'Saoubi, Rachid
  • Jiménez Piqué, Emilio|||0000-0002-6950-611X
  • Franca, Luiz F.P.
  • Llanes Pitarch, Luis Miguel|||0000-0003-1054-1073
Coated polycrystalline cubic boron nitride (PcBN) tools are increasingly used for industrial applications with stringent requirements. However, information on the mechanical integrity of these systems is quite limited. Within this context, the adhesion strength of two TiN/TiAlN-coated and microstructurally different PcBN substrates – high- and low-cBN content grades with metallic and ceramic binders, respectively – is investigated by means of Rockwell C indentation testing. In doing so, special attention is paid to substrate microstructure effects on emergence and evolution of damage as applied load is increased. For both coated systems, it is found that damage scenario evolves from early adhesive delamination within the contact area towards radial cracking and spalling outside the residual imprint. However, critical loads for transition between damage stages are discerned to depend on microstructural assemblage of the substrate. Higher resistance to radial cracking and delamination is exhibited by the high cBN-content grade, in agreement with its higher hardness and toughness. Failure micromechanisms associated with cracking and spalling are similar for both coated-PcBN systems. Very interesting, delamination outside the residual imprint is determined to be of cohesive nature within the substrate, an experimental fact resulting from interaction among indentation-induced radial, cone-like and lateral fissures in PcBN., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Influence of microstructural assemblage of the substrate on the adhesion strength of coated PcBN grades

  • Gordon Pozuelo, Sandra
  • Roa Rovira, Joan Josep
  • Rodríguez Suárez, Teresa
  • M'Saoubi, Rachid
  • Jiménez Piqué, Emilio
  • Franca, Luiz F.P.
  • Llanes Pitarch, Luis Miguel
Coated polycrystalline cubic boron nitride (PcBN) tools are increasingly used for industrial applications with stringent requirements. However, information on the mechanical integrity of these systems is quite limited. Within this context, the adhesion strength of two TiN/TiAlN-coated and microstructurally different PcBN substrates – high- and low-cBN content grades with metallic and ceramic binders, respectively – is investigated by means of Rockwell C indentation testing. In doing so, special attention is paid to substrate microstructure effects on emergence and evolution of damage as applied load is increased. For both coated systems, it is found that damage scenario evolves from early adhesive delamination within the contact area towards radial cracking and spalling outside the residual imprint. However, critical loads for transition between damage stages are discerned to depend on microstructural assemblage of the substrate. Higher resistance to radial cracking and delamination is exhibited by the high cBN-content grade, in agreement with its higher hardness and toughness. Failure micromechanisms associated with cracking and spalling are similar for both coated-PcBN systems. Very interesting, delamination outside the residual imprint is determined to be of cohesive nature within the substrate, an experimental fact resulting from interaction among indentation-induced radial, cone-like and lateral fissures in PcBN., Peer Reviewed, Postprint (published version)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Comparative study of mechanical performance of AlCrSiN coating deposited on WC-Co and cBN hard substrates

  • Liang, Jing
  • Serra, Marc
  • Gordon, Sandra
  • Fernández de Ara, Jonathan
  • Almandoz Sánchez, Eluxka
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
The objective of this study is to explore and compare the mechanical response of AlCrSiN coatings deposited on two different substrates, namely, WC-Co and cBN. Nano-indentation was used to measure the hardness and elastic modulus of the coatings, and micro-indentation was used for observing the contact damage under Hertzian contact with monotonic and cyclic (fatigue) loads. Microscratch and contact damage tests were also used to evaluate the strength of adhesion between the AlCrSiN coatings and the two substrates under progressive and constant loads, respectively. The surface damages induced via different mechanical tests were observed using scanning electron microscopy (SEM). A focused ion beam (FIB) was used to produce a cross-section of the coating–substrate system in order to further detect the mode and extent of failure that was induced. The results show that the AlCrSiN coating deposited on the WC-Co substrate performed better in regard to adhesion strength and contact damage response than the same coating deposited on the cBN substrate; this is attributed to the lower plasticity of the cBN substrate as well as its less powerful adhesion to the coating., This research was funded by The Spanish Ministry of Science, Innovation and Universities through grants PGC2018-096855-B-C41, PGC2018-096855-A-C44 and PID2021-126614OB-100.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Improved adhesion of cathodic arc PVD AlCrSiN coating on ion-implanted WC-Co substrates

  • Ortiz Membrado, Laia
  • García-González, Sandra
  • Orrit-Prat, Jordi
  • Bonet, Raül
  • Caro, Jaume
  • Fernández de Ara, Jonathan
  • Almandoz Sánchez, Eluxka
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
Ion implantation has been shown to improve adhesion strength of AlCrSiN coatings due to a synergic enhancement on fracture toughness and load bearing capability of the substrate that can potentially increase the in-service efficiency of coated cutting tools. In this work, AlCrSiN coatings deposited by PVD on WC-Co substrates implanted with Ti, Cr and N ion species have been processed. The mechanical properties and adhesion have been characterized by contact techniques and the residual stress of the coatings and substrates have been evaluated using FIB-DIC technique and Vickers indentation tests, respectively. An improvement of adhesion strength is obtained for treated substrates, especially for those implanted with titanium and chromium ions. This improvement is attributed to the introduction of residual stresses in the substrate, which increases its fracture toughness and enhances its load bearing capability., Work funded through The Spanish Ministry of Science, Innovation and Universities through grants PGC-2018-096855-B-C41, PGC-2018-096855-B-C42 and PGC-2018-096855-A-C44
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Improvement of the tribocorrosion properties of cemented carbide (WC-Tic-Co) samples with PVD coating

  • García Lorente, José Antonio
  • Claver Alba, Adrián
  • Marques, Mikel
  • Almandoz Sánchez, Eluxka
  • Fernández de Ara, Jonathan
  • Azkona, Ibon
This study aims to investigate the improvement of the tribocorrosion properties of WC-TiC-Co substrates by coating them with hard coatings such as AlCrSiN using cathodic arc deposition. WC-TiC-Co is commonly used in the fabrication of machining and cutting tools; however, there are some materials such as titanium or stainless steel that are difficult to work with; furthermore, in aggressive environments or under high temperatures the performance of the machining tools can be affected, and a failure may occur. This coating is intended to ensure the correct performance of the tools in any conditions. The coatings were characterized by glow discharge optical emission spectroscopy (GDOES), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Tribocorrosion, tribology and corrosion tests were performed to evaluate the tribocorrosion properties of the samples. Furthermore, mechanical and adhesive properties of the coating were studied using scratch and nanoindentation tests. The results showed improved tribocorrosion properties in the samples combined with good adhesive and mechanical properties. These results show the possibility of using these coated materials in the most demanding cutting and machining applications., Funded in part by the Spanish Ministry of Science, Innovation and Universities through grant PGC2018-096855-B-C43 and PGC2018-096855-A-C44.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Improved adhesion and tribological properties of altin-tisin coatings deposited by dcms and hipims on nitrided tool steels

  • Claver Alba, Adrián
  • Randulfe Ceballos, Jesús José
  • Fernández de Ara, Jonathan
  • Almandoz Sánchez, Eluxka
  • Montalá, Francesc
  • Colominas, Carles
  • Cot, Víctor
  • García Lorente, José Antonio
Hard coatings, such as AlTiN-TiSiN, deposited by Physical Vapor Deposition (PVD) techniques are widely used in industrial applications to protect and increase the lifetime of industrial components, such as cutting tools, dies, and forming tools. Despite their great properties, such as high hardness and wear and oxidation resistance, they are limited in cases of severe conditions due to the poor adhesion between the coating and the substrate. Duplex treatments have commonly been used to improve the adhesive properties of PVD coatings, especially those of the cathodic arc evaporation type. The purpose of this study is to achieve coatings with the good properties of the Magnetron Sputtering processes but with higher adhesion than that achieved with these techniques, thus achieving coatings that can be used under the most severe conditions. In this work, an AlTiN-TiSiN coating was deposited by a combination of DC Magnetron Sputtering (DCMS) and High-Power Impulse Magnetron Sputtering (HiPIMS) after a gas nitriding pretreatment on 1.2379 and Vanadis 4 tool steels. Mechanical (ultra-microhardness and scratch tests) and tribological tests were carried out to study the improvement in the properties of the coating. Duplex-treated samples showed improved adhesion between the coating and the substrate, with second critical load (Lc2) values greater than 100 N. Furthermore, they showed great toughness and wear resistance. These results show that this type of coating technique could be used in the most extreme applications and that they can compete with other techniques and coatings that to date they have not been able to compete with., This research was funded in part by the Spanish Ministry of Science, Innovation and Universities through grants PGC2018-096855-B-C43 and PGC2018-096855-A-C44.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Mechanical performance of AlCrSiN and AlTiSiN coatings on inconel and steel substrates after thermal treatments

  • Liang, Jing
  • Almandoz Sánchez, Eluxka
  • Ortiz Membrado, Laia
  • Rodríguez Lozano, Rafael
  • Fernández de Ara, Jonathan
  • García Fuentes, Gonzalo
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
The objective of this study was to explore the mechanical properties of AlCrSiN and AlTiSiN coatings deposited on Inconel and steel substrates after thermal treatments of 500 °C and 800 °C. Nanoindentation was used to measure the hardness and elastic modulus of the coatings, and microindentation was used for observing the contact damage with Hertzian contact loadings. Microscratch and Mercedes tests were used to evaluate the adhesive strength between coating and substrate with both progressive and static loads, respectively. The surface damage was inspected by optical microscopy and scanning electron microscopy (SEM). Focus ion beams (FIB) were used to mill the cross-sections in order to detect the extent and mode of failure. The results show that AlCrSiN coatings and Inconel substrates exhibit better mechanical performance, even after thermal treatments., The authors acknowledge the support from the Spanish ministry of Science, Innovation and Universities through grants PGC2018-096855-B-C41 and PGC2018-096855-A-C44.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Assessment of the mechanical performance of AlCrSiN coating implanted with Zr and Ta ions

  • Liang, Jing
  • Ortiz Membrado, Laia
  • Bonet, Raül
  • Orrit-Prat, Jordi
  • Caro, Jaume
  • Fernández de Ara, Jonathan
  • Almandoz Sánchez, Eluxka
  • Ruan, Qingdong
  • King-Yu Fu, Ricky
  • Chu, Paul K.
  • Llanes, Luis
  • Jiménez-Piqué, Emilio
This study explores the impact of Zr and Ta ion implantation on the mechanical performance of an AlCrSiN quaternary coating deposited on a WC-Co cermet substrate. Nanoindentation tests revealed a decrease in hardness and elastic modulus after ion implantation, compared to unimplanted coatings. Moreover, microscratch and contact damage tests demonstrated improved adhesion and reduced surface damage for ion-implanted samples, with Ta implantation exhibiting the best performance. Scanning Electron Microscopy (SEM) and focused ion beam (FIB) cross-sectional analysis confirmed less severe damage in ion-implanted samples compared to unimplanted ones. These findings suggest that Zr/Ta ion implantation enhances the structural integrity and adhesion of AlCrSiN coatings under loading conditions commonly encountered in practical applications, despite a moderate reduction in intrinsic hardness and elastic modulus., The work was funded by the Spanish Ministry of Science, Innovation, and Universities through grants PGC2018-096855-B-C41, PGC2018-096855-B-C43, and PGC2018-096855-A-C44