Pasar al contenido principal

SENSORES FOTONICOS BASADOS EN NANOPARTICULAS, NANOFIBRAS Y MATERIALES NANOESTRUCTURADOS

TEC2013-43679-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSIDAD PUBLICA DE NAVARRA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 32
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Continuous liquid-level sensor based on a long-period grating and microwave photonics filtering techniques

  • Ricchiuti, Amelia Lavinia
  • Urrutia Azcona, Aitor
  • Goicoechea Fernández, Javier
  • Arregui, Francisco J.
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
A fiber optic liquid-level sensor based on a long period grating (LPG) is proposed and experimentally validated. The principle of operation is based on a technique used to analyze microwave photonics filters. A 4-cm-long LPG cascaded with a high-reflectivity fiber Bragg grating is employed to achieve a continuous liquid-level sensor. The measurements have been performed using a modulator and a photo-detector with a modest bandwidth of less than 500 MHz, showing a sensitivity of −12.71 dB/cm and a standard deviation of 0.52 dB. One of the significant advantages of such sensing structure is that it is based on low-bandwidth radio frequency and off-the-shelf photonic components. In addition, the simple proposed scheme presents good repeatable performance and proves to be intrinsically robust against environmental changes, stable, and easy to reconfigure., This work was supported in part by the Accion Financiada por el Ministerio de Educacion, Cultura y Deporte through the framework of the Programa de Campus de Excelencia Internacional VLC/Campus, in part by the Spanish MINECO under Project TEC2014-60378-C2-1-R, in part by the Grant of the SANTIAGO GRISOLIA Program, in part by the Research Excellency Award Program GVA PROMETEO 2013/012, in part by the Project TEC2013-43679-R, and in part by an UPNA Predoctoral Grant. The associate editor coordinating the review of this paper and approving it for publication was Dr. Anna G. Mignani.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Simultaneous measurement of humidity and temperature based on a partially coated optical fiber long period grating

  • Urrutia, Aitor
  • Goicoechea, Javier
  • Ricchiuti, Amelia Lavinia
  • Arregui, Francisco J.
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
A humidity and temperature optical fiber sensor based on a long-period grating (LPG), which can provide simultaneous response to both magnitudes, is proposed and demonstrated via experiments. Previously, the LPG was fully coated with humidity sensitive nanostructured polymeric thin films by the Layer-by-Layer (LbL) nano assembly technique. Hence the surrounding refractive index was changed, so provoking wavelength shifts of the attenuation bands of the transmission spectrum. This fully coated LPG was exposed to relative humidity (RH) and temperature tests, varying from 20% to 80% RH and from 25 to 85ºC, respectively. Then, half of the LPG coating was chemically removed and this results in the splitting of the main attenuation band into two different contributions. When this semi-coated LPG was also exposed to RH and temperature tests, the new two attenuation bands presented different behaviors for humidity and temperature. This novel dual-wavelength based sensing method enables the simultaneous measurement of RH and temperature using only one LPG., This work was supported in part by the Spanish Ministry of Economy and Competitiveness - through the projects CICYT-FEDER TEC2013-43679-R and TEC2014-60378-C2-1-R. It was also supported by a UPNA pre-doctoral research grant, by the Program of International Excellence Campus VLC/Campus, by the grant of program SANTIAGO GRISOLIA, and by the Research Excellency Award Program GVA PROMETEO 2013/012.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Sensors based on thin-film coated cladding removed multimode optical fiber and single-mode multimode single-mode fiber: a comparative study

  • Del Villar, Ignacio
  • Socorro Leránoz, Abián Bentor
  • Hernáez Sáenz de Zaitigui, Miguel
  • Corres Sanz, Jesús María
  • Ruiz Zamarreño, Carlos
  • Sánchez Zábal, Pedro
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
Two simple optical fibre structures that do not require the inscription of a grating, a cladding removed multimode optical fibre (CRMOF) and a single-mode multimode single-mode structure (SMS), are compared in terms of their adequateness for sensing once they are coated with thin-films.The thin-film deposited (TiO2/PSS) permits increasing the sensitivity to surrounding medium refractive index. The results obtained can be extrapolated to other fields such as biological or chemical sensing just by replacing the thin-film by a specific material., This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Fluorescent sensors for the detection of heavy metal ions in aqueous media

  • Acha Morrás, Nerea de
  • Elosúa Aguado, César
  • Corres Sanz, Jesús María
  • Arregui San Martín, Francisco Javier
Due to the risks that water contamination implies for human health and environmental protection, monitoring the quality of water is a major concern of the present era. Therefore, in recent years several efforts have been dedicated to the development of fast, sensitive, and selective sensors for the detection of heavy metal ions. In particular, fluorescent sensors have gained in popularity due to their interesting features, such as high specificity, sensitivity, and reversibility. Thus, this review is devoted to the recent advances in fluorescent sensors for the monitoring of these contaminants, and special focus is placed on those devices based on fluorescent aptasensors, quantum dots, and organic dyes., This work was supported by the Spanish State Research Agency (AEI) and the Spanish Ministry of Economy and Competitiveness through the TEC2016-79367-C2-2-R project. Nerea de Acha would also like to acknowledge her pre-doctoral fellowship (reference BES-2014-069692) funded by the Spanish Ministry of Economy and Competitiveness through the TEC2013-43679-R project.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Etched LPFGs in reflective configuration for sensitivity and attenuation band depth increase

  • Del Villar, Ignacio
  • Socorro Leránoz, Abián Bentor
  • Corres Sanz, Jesús María
  • Matías Maestro, Ignacio
  • Cruz, José Luis
  • Rego, Gaspar
A reflection configuration setup for long-period fiber gratings is presented. It permits to obtain a unique band with attenuation double than that obtained in transmission configuration, which is interesting for applications where this value is reduced (e.g., the mode transition phenomenon). The method is based on the deposition of a silver mirror at the end of the optical fiber, which permits to absorb the power transmitted through cladding modes and to avoid the generation of interferometric bands. The method also solves the requirement of a precise cleave or to polish the end of the grating, a drawback present in other publications. The versatility of the setup has been proved by application of the cladding etching technique until the attenuation band corresponding with the first guided mode in the cladding is visualized in an optical spectrum analyzer. The experimental results are supported by the numerical data obtained with a method based on the exact calculation of core and cladding modes and the utilization of coupled mode theory, This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R and TEC2013-46643-C2-1-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optical sensors based on lossy-mode resonances

  • Matías Maestro, Ignacio
  • Ascorbe Muruzabal, Joaquín
  • Acha Morrás, Nerea de
  • López Torres, Diego
  • Zubiate Orzanco, Pablo
  • Sánchez Zábal, Pedro
  • Urrutia Azcona, Aitor
  • Socorro Leránoz, Abián Bentor
  • Rivero Fuente, Pedro J.
  • Hernáez Sáenz de Zaitigui, Miguel
  • Elosúa Aguado, César
  • Goicoechea Fernández, Javier
  • Bariáin Aisa, Cándido
  • Corres Sanz, Jesús María
  • Ruiz Zamarreño, Carlos
  • Arregui San Martín, Francisco Javier
  • Del Villar, Ignacio
Lossy-mode resonance (LMR)–based optical sensing technology has emerged in the last two decades as a nanotechnological platform with very interesting and promising properties. LMR complements the metallic materials typically used in surface plasmon resonance (SPR)–based sensors, with metallic oxides and polymers. In addition, it enables one to tune the position of the resonance in the optical spectrum, to excite the resonance with both transverse electric (TE) and transverse magnetic (TM) polarized light, and to generate multiple resonances. The domains of application are numerous: as sensors for detection of refractive indices voltage, pH, humidity, chemical species, and antigens, as well as biosensors. This review will discuss the bases of this relatively new technology and will show the main contributions that have permitted the optimization of its performance to the point that the question arises as to whether LMR–based optical sensors could become the sensing platform of the near future., This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Simultaneous measurement of humidity and temperature based on a partially coated optical fiber long period grating

  • Urrutia Azcona, Aitor
  • Goicoechea Fernández, Javier
  • Ricchiuti, Amelia L.
  • Barrera, David
  • Arregui San Martín, Francisco Javier
A humidity and temperature optical fiber sensor based on a long-period grating (LPG), which can provide simultaneous response to both magnitudes, is proposed and demonstrated via experiments. Previously, the LPG was fully coated with humidity sensitive nanostructured polymeric thin films by the Layer-by-Layer (LbL) nano assembly technique. Hence the surrounding refractive index was changed, so provoking wavelength shifts of the attenuation bands of the transmission spectrum. This fully coated LPG was exposed to relative humidity (RH) and temperature tests, varying from 20% to 80% RH and from 25 to 85 °C, respectively. Then, half of the LPG coating was chemically removed and this results in the splitting of the main attenuation band into two different contributions. When this semi-coated LPG was also exposed to RH and temperature tests, the new two attenuation bands presented different behaviors for humidity and temperature. This novel dual-wavelength based sensing method enables the simultaneous measurement of RH and temperature using only one LPG., This work was supported in part by the Spanish Ministry of Economy and Competitiveness – through the projects CICYT-FEDER TEC2013-43679-R and TEC2014-60378-C2-1-R. It was also supported by a UPNA pre-doctoral research grant, by the Program of International Excellence Campus VLC/Campus, by the grant of program SANTIAGO GRISOLÍA, and by the Research Excellency Award Program GVA PROMETEO 2013/012.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Giant sensitivity of optical fiber sensors by means of lossy moderesonance

  • Arregui San Martín, Francisco Javier
  • Del Villar, Ignacio
  • Ruiz Zamarreño, Carlos
  • Zubiate Orzanco, Pablo
  • Matías Maestro, Ignacio
Here we show an optical refractometer with a giant sensitivity of 304,360 nm per refractive index unit(nm/RIU). This sensitivity corresponds to a resolution of 3.28 × 10−9RIU if a standard optical spectrumanalyzer with a resolution of 1 pm is used. This record sensitivity is obtained by means of a lossy moderesonance (LMR) optical fiber sensor in a surrounding media with refractive index around 1.45. Thisachievement implies that the utilization of the LMR phenomenon opens the door to devices and systemsthat can beat, in terms of sensitivity, those used currently in real-time biomolecular analysis such assurface plasmon resonance (SPR) devices., This work was supported in part by the Spanish Ministry of Economy and Competitiveness (MINECO)-under contract FEDER TEC2013-43679-R
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Fabrication of Bragg gratings on the end facet of standard optical fibers by sputtering the same material

  • Ascorbe Muruzabal, Joaquín
  • Corres Sanz, Jesús María
  • Del Villar, Ignacio
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
A sputtering process has been applied to deposit quarter-wavelength stacks on the end facet of cleaved optical fibers by using only one sputtering target. Standard multimode optical fibers were used as substrates to fabricate broadband filters, and the experimentally measured spectral responses of these devices are shown. Periodical changes in the refractive index of the coating have been achieved by changing the vacuum chamber pressure. A reflected peak with a full-width at half-maximum of 20 nm centered at 440 nm has been obtained, which provides a good structure for the development of optical fiber sensors working with the wavelength detection technique. This optical structure can be used for several purposes: as tunable wavelength filters or optical fiber sensors or to improve the performance of fluorescence sensors. A theoretical analysis of these structures corroborates the experimental results and allows some rules to be obtained., This work was supported by a Public University of Navarra PhD Grant and by the Spanish Economy and Competitiveness Ministry, TEC-2013-43679-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Luminescence-based optical sensors fabricated by means of the layer-by-layer nano-assembly technique

  • Acha Morrás, Nerea de
  • Elosúa Aguado, César
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
Luminescence-based sensing applications range from agriculture to biology, including medicine and environmental care, which indicates the importance of this technique as a detection tool. Luminescent optical sensors are required to be highly stable, sensitive, and selective, three crucial features that can be achieved by fabricating them by means of the layer-by-layer nano-assembly technique. This method permits us to tailor the sensors0 properties at the nanometer scale, avoiding luminophore aggregation and, hence, self-quenching, promoting the diffusion of the target analytes, and building a barrier against the undesired molecules. These characteristics give rise to the fabrication of custom-made sensors for each particular application., This work was supported by the Spanish State Research Agency (AEI) through the TEC2016- 79367-C2-2-R project and the European Regional Development Fund (ERDF-FEDER). Nerea de Acha would also like to acknowledge her pre-doctoral fellowship (reference BES-2014-069692) funded by the Spanish Ministry of Economy and Competitiveness through the TEC2013-43679-R project.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High sensitivity humidity sensor based on cladding-etched optical fiber and lossy mode resonances

  • Ascorbe Muruzabal, Joaquín
  • Corres Sanz, Jesús María
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
In this work a high sensitivity optical fiber humidity sensor (OFHS) is presented. The configuration chosen for this purpose is a cladding-etched single mode optical fiber (CE-SMF) coated with a thin film of tin oxide (SnO2). The etching has been made using hydrofluoric acid (HF) and the coating has been fabricated by means of sputtering. Tin oxide was used to build the nano-coating which produces the Lossy Mode Resonance (LMR) and works as sensitive material. Theoretical and experimental results are shown and compared. The device was tested using a climatic chamber in order to obtain the response of the OFHS to relative humidity. Changes greater than 130 nm have been obtained for relative humidity varying from 20% to 90%, which gives a sensitivity of 1.9 nm/%RH., This work was supported by a Public University of Navarra PhD Grant and by the Spanish Economy and Competitiveness Ministry TEC-2013-43679-R Research Grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Enhancing sensitivity of photonic crystal fiber interferometric humidity sensor by the thickness of SnO2 thin films

  • López Torres, Diego
  • Elosúa Aguado, César
  • Villatoro, Joel
  • Zubia, Joseba
  • Rothhardt, Manfred
  • Schuster, Kay
  • Arregui San Martín, Francisco Javier
In order to improve the sensitivity of an interferometric humidity sensor based on a photonic crystal fiber with a sputtered SnO2 nanocoating, a study of the effect of its thickness on the sensitivity is presented in this paper. Sensors with coatings of different thickness were performed by applying distinct sputtering times in order to obtain an optimal thickness: the resulting nanofilms ranged from 470 to 1800 nm. Sensors were tested increasing the relative humidity from 20% to 90%, finding that the thickness was a key parameter which has to be optimized at nanometer scale to get the best sensitivity. The study points that there is an optimal thickness and higher or lower thicknesses worsen the sensitivity of the sensor. The optimal sensor showed a humidity resolution of 0.067%HR, a wavelength shift of 67 nm and a negligible sensitivity with the temperature., This work was supported by the Spanish Economy and Competitivity Ministry-FEDER TEC2013-43679-R as well as Public University of Navarre grant program.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Temperature sensor based on a hybrid ITOsilica resonant cavity

  • Socorro Leránoz, Abián Bentor
  • Soltani, Soheil
  • Del Villar, Ignacio
  • Corres Sanz, Jesús María
  • Armani, Andrea M.
Integrated optical devices comprised of multiple material systems are able to achieve unique performance characteristics, enabling applications in sensing and in telecommunications. Due to ease of fabrication, the majority of previous work has focused on polymer-dielectric or polymer-semiconductor systems. However, the environmental stability of polymers is limited. In the present work, a hybrid device comprised of an indium tin oxide (ITO) coating on a silicon dioxide toroidal resonant cavity is fabricated. Finite element method simulations of the optical field in the multi-material device are performed, and the optical mode profile is significantly altered by the high index film. The quality factor is also measured and is material loss limited. Additionally, its performance as a temperature sensor is characterized. Due to the high thermo-optic coefficient of ITO and the localization of the optical field in the ITO layer, the hybrid temperature sensor demonstrates a nearly 3-fold improvement in performance over the conventional silica device., This work has been supported by institutions both in Spain and in the USA. A pre-doctoral research grant of the Public University of Navarra and the Spanish Ministry of Economy and Competitiveness FEDER TEC2013-43679-R project from Spain. Also, the National Institute of Health through the Director’s New Innovator Award Program [1DP2OD007391-01] from the United States of America.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Continuous liquid-level sensor based on a long-period grating and microwave photonics filtering techniques

  • Ricchiuti, Amelia L.
  • Barrera, David
  • Urrutia Azcona, Aitor
  • Goicoechea Fernández, Javier
  • Arregui San Martín, Francisco Javier
A fiber optic liquid-level sensor based on a long period grating (LPG) is proposed and experimentally validated. The principle of operation is based on a technique used to analyze microwave photonics filters. A 4-cm-long LPG cascaded with a high-reflectivity fiber Bragg grating is employed to achieve a continuous liquid-level sensor. The measurements have been performed using a modulator and a photo-detector with a modest bandwidth of less than 500 MHz, showing a sensitivity of -12.71 dB/cm and a standard deviation of 0.52 dB. One of the significant advantages of such sensing structure is that it is based on low-bandwidth radio frequency and off-the-shelf photonic components. In addition, the simple proposed scheme presents good repeatable performance and proves to be intrinsically robust against environmental changes, stable, and easy to reconfigure., This work was supported in part by the Acción Financiada por el Ministerio de Educación, Cultura y Deporte through the framework of the Programa de Campus de Excelencia Internacional VLC/Campus, in part by the Spanish MINECO under Project TEC2014-60378-C2-1-R, in part by the Grant of the SANTIAGO GRISOLÍA Program, in part by the Research Excellency Award Program GVA PROMETEO 2013/012, in part by the Project TEC2013-43679-R, and in part by an UPNA Predoctoral Grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Sensitivity optimization with cladding-etched long period fiber gratings at the dispersion turning point

  • Del Villar, Ignacio
  • Cruz, José Luis
  • Socorro Leránoz, Abián Bentor
  • Corres Sanz, Jesús María
  • Matías Maestro, Ignacio
This work presents a refractive index sensor based on a long period fiber grating (LPFG) made in a reduced cladding fiber whose low order cladding modes have the turning point at large wavelengths. The combination of these parameters results in an improved sensitivity of 8734 nm/refractive index unit (RIU) for the LP0,3 mode in the 1400-1650 wavelength range. This value is similar to that obtained with thin-film coated LPFGs, which permits to avoid the coating deposition step. The numerical simulations are in agreement with the experimental results., This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R. J.L. Cruz also acknowledges financial support of project TEC2013-46643-C2-1-R, and the Generalitat Valenciana project PROMETEOII/2014/072.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Novel highly sensitive protein sensors based on tapered optical fibres modified with Au-based nanocoatings

  • Urrutia Azcona, Aitor
  • Bojan, Kartheka
  • Marques, Leonel
  • Mullaney, Kevin
  • Goicoechea Fernández, Javier
  • James, Stephen
  • Clark, Matt
  • Tatam, Ralph
  • Korposh, Sergiy
Novel protein sensors based on tapered optical fibres modified with Au coatings deposited using two different procedures are proposed. Au-based coatings are deposited onto a nonadiabatic tapered optical fibre using (i) a novel facile method composed of layer-by-layer deposition consisting of polycation (poly(allylamine hydrochloride), PAH) and negatively charged SiO2 nanoparticles (NPs) followed by the deposition of the charged Au NPs and (ii) the sputtering technique. The Au NPs and Au thin film surfaces are then modified with biotin in order to bind streptavidin (SV) molecules and detect them. The sensing principle is based on the sensitivity of the transmission spectrum of the device to changes in the refractive index of the coatings induced by the SV binding to the biotin. Both sensors showed high sensitivity to SV, with the lowest measured concentration levels below 2.5 nM. The calculated binding constant for the biotin-SV pair was 2.2 × 10−11 M−1 when a tapered fibre modified with the LbL method was used, with a limit of detection (LoD) of 271 pM. The sensor formed using sputtering had a binding constant of 1.01 × 10−10 M−1 with a LoD of 806 pM. These new structures and their simple fabrication technique could be used to develop other biosensors., This work was supported in part by the Spanish Ministry of Economy and Competitiveness-CICYT-FEDER TEC2013-43679R Research Grant and UPNA predoctoral and mobility research grants. The authors also acknowledge the support of UK Engineering and Physical Sciences Research Council Platform grant (EP/H02252X/1) and responsive mode grant (EP/L010437/1). The authors would like also to acknowledge the support of the EPSRC EP/G061661/1 Advanced Ultrasonics Platform Grant, University of Nottingham, Dean of Engineering Faculty Award.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Generation of surface plasmon resonance and lossy mode resonance by thermal treatment of ITO thin-films

  • Del Villar, Ignacio
  • Ruiz Zamarreño, Carlos
  • Hernáez Sáenz de Zaitigui, Miguel
  • Sánchez Zábal, Pedro
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
Silicon wafers coated with IndiumTinOxide (ITO) by application of sputtering technique have been characterized after different post-annealing techniques, showing that this last factor is critical for the quality of the thin-film and for the creation and tuning of both surface plasmon resonances and lossy mode resonances. By adequate selection of the ITO thin-film thickness both resonances can be tracked in the same spectrum, which can be used in sensor and optical communications fields., This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High sensitive and selective C-reactive protein detection by means of lossy mode resonance based optical fiber devices

  • Zubiate Orzanco, Pablo
  • Ruiz Zamarreño, Carlos
  • Sánchez Zábal, Pedro
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
This work presents the development of high sensitive, selective, fast and reusable C-reactive protein (CRP) aptasensors. This novel approach takes advantage of the utilization of high sensitive refractometers based on Lossy Mode Resonances generated by thin indium tin oxide (ITO) films fabricated onto the planar region of D-shaped optical fibers. CRP selectivity is obtained by means of the adhesion of a CRP specific aptamer chain onto the ITO film using the Layer-by-Layer (LbL) nano-assembly fabrication process. The sensing mechanism relies on resonance wavelength shifts originated by refractive index variations of the aptamer chain in presence of the target molecule. Fabricated devices show high selectivity to CRP when compared with other target molecules, such as urea or creatinine, while maintaining a low detection limit (0.0625 mg/L) and fast response time (61 s). Additionally, these sensors show a repetitive response for several days and are reusable after a cleaning process in ultrapure water., This work was supported by a Pre-Doctoral Research Grant of the Public University of Navarra, Spanish Economy and Competitiveness Ministry-Feder TEC2013-43679-R and Fundación CAN2015-70221 Research Grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High sensitive refractometers based on lossy mode resonances (LMRs) supported by ITO coated D-shaped optical fibers

  • Zubiate Orzanco, Pablo
  • Ruiz Zamarreño, Carlos
  • Del Villar, Ignacio
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
Tin doped indium oxide (ITO) coatings fabricated onto D-shaped optical fibers are presented as the supporting medium for Lossy Mode Resonances (LMRs) generation. The characteristic geometry of ITO-coated D-shaped optical fibers enables to observe experimentally LMRs obtained with both TM and TE polarized light (LMRTM and LMRTE). This permits to obtain a maximum transmission decay of 36 dB with a LMR spectral width of 6.9 nm, improving that obtained in previous works, where the LMRs were a combination of an LMRTM and an LMRTE. Surrounding medium refractive index (SMRI) sensitivity characterization of LMRTM has been performed obtaining a maximum sensitivity of 8742 nm/RIU in the range 1.365-1.38 refractive index units (RIU) which overcomes that of surface plasmon resonance-based optical fiber devices presented in recent works., This work was supported by the Spanish Economy and Competitiveness Ministry-Feder TEC2013-43679-R Research Grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Nanomaterials for functional textiles and fibers

  • Rivero Fuente, Pedro J.
  • Urrutia Azcona, Aitor
  • Goicoechea Fernández, Javier
  • Arregui San Martín, Francisco Javier
Nanoparticles are very interesting because of their surface properties, different from bulk materials. Such properties make possible to endow ordinary products with new functionalities. Their relatively low cost with respect to other nano-additives make them a promising choice for industrial mass-production systems. Nanoparticles of different kind of materials such as silver, titania, and zinc oxide have been used in the functionalization of fibers and fabrics achieving significantly improved products with new macroscopic properties. This article reviews the most relevant approaches for incorporating such nanoparticles into synthetic fibers used traditionally in the textile industry allowing to give a solution to traditional problems for textiles such as the microorganism growth onto fibers, flammability, robustness against ultraviolet radiation, and many others. In addition, the incorporation of such nanoparticles into special ultrathin fibers is also analyzed. In this field, electrospinning is a very promising technique that allows the fabrication of ultrathin fiber mats with an extraordinary control of their structure and properties, being an ideal alternative for applications such as wound healing or even functional membranes., This work was supported in part by the Spanish Ministry of Economy and Competitiveness—CICYT-FEDER TEC2013-43679-R research grant, and an UPNA pre-doctoral research grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optical fiber sensors based on nanoparticle-embedded coatings

  • Urrutia Azcona, Aitor
  • Goicoechea Fernández, Javier
  • Arregui San Martín, Francisco Javier
The use of nanoparticles (NPs) in scientific applications has attracted the attention of many researchers in the last few years. The use of NPs can help researchers to tune the physical characteristics of the sensing coating (thickness, roughness, specific area, refractive index, etc.) leading to enhanced sensors with response time or sensitivity better than traditional sensing coatings. Additionally, NPs also offer other special properties that depend on their nanometric size, and this is also a source of new sensing applications. This review focuses on the current status of research in the use of NPs within coatings in optical fiber sensing. Most used sensing principles in fiber optics are briefly described and classified into several groups: absorbance-based sensors, interferometric sensors, fluorescence-based sensors, fiber grating sensors, and resonance-based sensors, among others. For each sensor group, specific examples of the utilization of NP-embedded coatings in their sensing structure are reported., This work was supported in part by the Spanish Ministry of Economy and Competitiveness CICYT-FEDER TEC2013-43679-R Research Grant and a UPNA predoctoral research grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optical fiber sensors based on gold nanorods embedded in polymeric thin films

  • Urrutia Azcona, Aitor
  • Goicoechea Fernández, Javier
  • Rivero Fuente, Pedro J.
  • Pildain Lería, Ander
  • Arregui San Martín, Francisco Javier
In this work, we present a study about the generation and analysis of optical resonances caused by gold nanorods (GNRs) embedded in films. GNRs were embedded in polymeric thin films using the Layerby-Layer nanoassembly (LbL) deposition technique. Polymer/GNRs thin films of different thicknesses were deposited on the surface of cladding removed optical fibers for sensing. The spectral responses of the optical fiber sensors were monitored during the build-up of the thin films. The generation of two Localized Surface Plasmon Resonances (LSPRs) associated to the GNRs was observed in thinner coatings. These devices with around 12 polymer/GNRs bilayers were characterized as refractometers, providing an intensity-based sensitivity up to 75.69 dB/RIU. For thicker polymer/GNRs overlays, both LSPRs bands were also generated and, additionally, it was observed a new Lossy Mode Resonance (LMR) band due to modes coupled to the sensitive coating. The dependence of these three resonance bands with the surrounding refractive index was studied. Finally, these sensors were tested in a climatic chamber in the 20-90% relative humidity (RH) range and the LMR showed a good sensitivity to RH changes while the LSPR bands remained very stable in comparison. Results showed an excellent sensitivity of 11.2 nm/%RH for the LMR, confirming the potential of this type of optical fiber sensor based on the combination of LSPRs and LMRs bands., This work was supported in part by the Spanish Ministry of Economy and Competitiveness - CICYT-FEDER TEC2013-43679R, TEC2016-79367-C2-2-R, TEC2016-78047-R and TRA2013-48603-C4-1-R Research Grants, and a UPNA post-doctoral research grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

An optimized method based on digitalized Lissajous curve to determine lifetime of luminescent materials on optical fiber sensors

  • Ridruejo Muro, Adrián
  • Acha Morrás, Nerea de
  • Elosúa Aguado, César
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
A method is proposed to determine lifetime of luminescent emissions based on the phase shift measurement employing the digitalized Lissajous representation: this diagram has been typically used with analogical algorithms, whereas the proposed method is performed in digital domain, showing an improved accuracy and repeatability. The procedure is studied and tested with two different oxygen sensors that show different sensitivities and signal levels in order to confirm the no influence of the signals intensity on the calibration process.The computational cost of the proposed method is low, which makes it possible to monitor in real time luminescence sensors based on reversible quenching with a potential low cost system based on a digital signal processor (DSP)., This work was supported in part by the Spanish Ministry of Economy and Competitiveness FEDER TEC2013-43679-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Ultrahigh-sensitivity sensors based on thin-film coated long period gratings with reduced diameter, in transition mode and near the dispersion turning point

  • Del Villar, Ignacio
The mode transition and the dispersion turning point have been explored for optimization of thin-film coated long period fiber gratings during the last years. In this work and additional parameter, the cladding diameter, is combined with the other two phenomena for improving the sensitivity to the surrounding medium refractive index. The numerical data obtained were calculated with a method based on the exact calculation of core and cladding modes and the utilization of coupled mode theory. A sensitivity 143 × 103 nm/RIU is obtained, the highest reported so far with long period fiber gratings., This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Experimental demonstration of lossy mode and surface plasmon resonance generation with Kretschmann configuration

  • Del Villar, Ignacio
  • Torres Landívar, Víctor
  • Beruete Díaz, Miguel
Lossy mode resonances (LMRs) and surface plasmon resonaces (SPRs) are obtained experimentally with a Kretschmann configuration using a BK7 glass prism with all sides polished and coated with indium tin oxide (ITO). The properties of ITO allow for obtaining LMRs and SPRs with the same experimental setup. The results are corroborated with a numerical method for calculation of the reflection in the Kretschmann configuration., This work was supported in part by the Spanish Ministry of Education and Science under contracts FEDER TEC2013-43679-R, CSD2008-00066 and TEC2011-28664-C02. The FTIR spectrometer was financed by the Spanish Ministry of Economy and Competitiveness in the frame of the project CEI10-2-2005. M. Beruete acknowledges funding by the Spanish Government under the research contract program Ramón y Cajal RYC-2011-08221.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Photonic crystal fiber interferometer coated with a PAH/PAA nanolayer as humidity sensor

  • López Torres, Diego
  • Elosúa Aguado, César
  • Villatoro, Joel
  • Zubia, Joseba
  • Rothhardt, Manfred
  • Schuster, Kay
  • Arregui San Martín, Francisco Javier
Alojado según Res. CNEAI 5/12/23, In this paper, an optical fiber interferometric humidity sensor is presented. The device consists of 1 cmlong segment of photonic crystal fiber (PCF) spliced to standard single mode fibers (SMFs), forming an interferometer: the two collapsed interfaces between PCF and SMF segments produce the excitation and recombination of core and cladding modes. The latter interact with a poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) polymeric nanocoating deposited on the PCF by the well-established layer-by-layer nano assembly (LbL) technique. Humidity modifies the index of the polymeric nanolayer which in turns alters the cladding modes along the PCF segment and causes a detectable shift to the interference pattern. A study of different nanocoting thicknesses is presented in order to obtain the best possible sensibility for the sensor. Furthermore, the interrogation of the humidity sensor is presented not only by the conventional study of the spectrum shift amplitude, but also making use of the Fast Fourier Transform (FFT), which yields a linearization of the device response. The sensor here presented is reproducible, can resolve 0.074% of relative humidity (RH) and operates in the 20–95% RH range. Moreover, it exhibits response time of 0.3 s, a negligible cross sensitivity to temperature as well as long term stability., This work was supported by the Spanish Economy and Competitivity Ministry-FEDER TEC2013-43679-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Tunable optical fiber pH sensors based on TE and TM Lossy Mode Resonances (LMRs)

  • Zubiate Orzanco, Pablo
  • Ruiz Zamarreño, Carlos
  • Del Villar, Ignacio
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
In this paper, a high sensitivity optical fiber pH sensor based on lossy mode resonance (LMR) generated with transversal electric (TE) and transversal magnetic (TM) polarized light is presented. Poly(allylamine hydrochloride) (PAH)/poly(acrylic acid) (PAA) polymeric thin-films fabricated onto side-polished Dshaped optical fibers are used as pH-sensitive as well as LMR supporting coatings. The adequate selection of the pH-sensitive coating fabrication parameters enables to obtain devices working at different pH regions. Two devices have been obtained in order to measure pH from 4.0 to 5.0 and from 7.0 to 8.0 respectively. Obtained optical fiber pH sensors based on TE and TM LMRs showed a maximum sensitivity of 69 nm/pH, which means a resolution of ∼0.0008 pH units by using a conventional communications Optical Spectrum Analyzer (OSA) with 0.06 nm resolution., This work was supported by the Spanish Economy and Competitiveness Ministry-Feder TEC2013-43679-R and Fundación CAN2015-70221 Research Grants
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A comparative study in the sensitivity of optical fiber refractometers based on the incorporation of gold nanoparticles into layer-by-layer films

  • Rivero Fuente, Pedro J.
  • Hernáez Sáenz de Zaitigui, Miguel
  • Goicoechea Fernández, Javier
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
In this work, optical fiber refractometers based on the successive incorporation of gold nanoparticles have been fabricated by means of the Layer-by-Layer Embedding (LbL-E) deposition technique. This enables the apparition of two different optical phenomena, Localized Surface Plasmon Resonance (LSPR) and Lossy Mode Resonance (LMR). The absorption peaks related to both phenomena were captured during the fabrication process, showing a different evolution as a function of the resultant thickness coating. Initially, LSPR band is observed for thinner coatings, whereas multi-LMR bands are observed as the thickness coating is increased. In addition, the response of both phenomena to variations of the surrounding medium refractive index (SMRI) was monitored, studying their different sensitivities. LSPR band only shows intensity variation with negligible wavelength displacement whereas LMR bands present a strong wavelength response. The combination of both resonances opens the door in the design of self-referenced optical devices for sensing applications., This work was supported by the Spanish Economy and Competitiveness Ministry-Feder TEC2013-43679-R and by the Government of Navarra research grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optimization in nanocoated D-shaped optical fiber sensors

  • Del Villar, Ignacio
  • Zubiate Orzanco, Pablo
  • Ruiz Zamarreño, Carlos
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
Nanocoated D-shaped optical fibers have been proven as effective sensors. Here, we show that the full width at half minimum (FWHM) of lossy mode resonance can be reduced by optimizing the nanocoating width, thickness and refractive index. As a counterpart, several resonances are observed in the optical spectrum for specific conditions. These resonances are caused by multiple modes guided in the nanocoating. By optimizing the width of the coating and the imaginary part of its refractive index, it is possible to isolate one of these resonances, which allows one to reduce the full width at half minimum of the device and, hence, to increase the figure of merit. Moreover, it is even possible to avoid the need of a polarizer by designing a device where the resonance bands for TE and TM polarization are centered at the same wavelength. This is interesting for the development of optical filters and sensors with a high figure of merit., Spanish Ministry of Education and Science-FEDER (TEC2013-43679-R, TEC2016-78047- R); Government of Navarra Health Department (64/2015, 72/2015); Government of Navarra 2016/PI008.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Experimental study and sensing applications of polarization-dependent lossy mode resonances generated by D-shape coated optical fibers

  • Zubiate Orzanco, Pablo
  • Ruiz Zamarreño, Carlos
  • Del Villar, Ignacio
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
The fabrication and characterization of an optical fiber refractometer based on Lossy Mode Resonances (LMR) is presented. TiO2/ poly (sodium 4-styrenesulfonate) (PSS) coatings deposited on side-polished D-shaped optical fibers are used as LMR supporting coatings. LMRs are sensitive to the external medium refractive index and D-shaped optical fibers enable the observation of TE and TM LMR polarizations. These refractometers based on TE and TM LMR showed an average sensitivity of 2737 nm/RIU and 2893 nm/RIU respectively for a surrounding medium refractive index (SMRI) range from 1.35 to 1.41. This work also explores the utilization of previously described refractometers in the context of two common industrial applications such as the determination of the sugar content or °Brix in beverages and the salt concentration in sea water., This work was supported by the Spanish Economy and Competitiveness Ministry-Feder TEC2013-43679-R Research Grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optical fibre sensors using graphene-based materials: a review

  • Hernáez Sáenz de Zaitigui, Miguel
  • Ruiz Zamarreño, Carlos
  • Melendi Espina, Sonia
  • Bird, Liam
  • Mayes, Andrew
  • Arregui San Martín, Francisco Javier
Graphene and its derivatives have become the most explored materials since Novoselov and Geim (Nobel Prize winners for Physics in 2010) achieved its isolation in 2004. The exceptional properties of graphene have attracted the attention of the scientific community from different research fields, generating high impact not only in scientific journals, but also in general-interest newspapers. Optical fibre sensing is one of the many fields that can benefit from the use of these new materials, combining the amazing morphological, chemical, optical and electrical features of graphene with the advantages that optical fibre offers over other sensing strategies. In this document, a review of the current state of the art for optical fibre sensors based on graphene materials is presented., This work was supported in part by the following Research Grants: Spanish Economy and Competitiveness Ministry-Feder TEC2013-43679-R, Government of Navarra Health Department 64/2015, and European Commission H2020-MSCA-IF-2015 703185.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Indium tin oxide refractometer in the visible and near infrared via lossy mode and surface plasmon resonances with Kretschmann configuration

  • Torres Landívar, Víctor
  • Beruete Díaz, Miguel
  • Sánchez Zábal, Pedro
  • Del Villar, Ignacio
The following article appeared in Torres, V., Beruete, M., Del Villar, I., & Sánchez, P. (2016). Indium tin oxide refractometer in the visible and near infrared via lossy mode and surface plasmon resonances with Kretschmann configuration. Applied Physics Letters, 108(4), doi:10.1063/1.4941077, and may be found at http://dx.doi.org/10.1063/1.4941077., An indium tin oxide (ITO) refractometer based on the generation of lossy mode resonances (LMRs) and surface plasmon resonances (SPRs) is presented. Both LMRs and SPRs are excited, in a single setup, under grazing angle incidence with Kretschmann configuration in an ITO thin- film deposited on a glass slide. The sensing capabilities of the device are demonstrated using several solutions of glycerin and water with refractive indices ranging from 1.33 to 1.47. LMRs are excited in the visible range, from 617 nm to 682 nm under TE polarization and from 533nm to 637nm under TM polarization, with a maximum sensitivity of 700 nm/RIU and 1200 nm/RIU, respectively. For the SPRs, a sensing range between 1375 nm and 2494 nm with a maximum sensitivity of 8300 nm/RIU is measured under TM polarization. Experimental results are supported with numerical simulations based on a modification of the plane-wave method for a one- dimensional multilayer waveguide., This work was supported in part by the Spanish Ministry of Education and Science-under Contracts FEDER TEC2013-43679-R and TEC2014-51902-C2-2-R. The FTIR spectrometer was financed by the Spanish Ministry of Economy and Competitiveness in the frame of the Project CEI10-2-2005. M. Beruete acknowledges funding by the Spanish Government under the Research Contract Program Ramón y Cajal RYC-2011-08221.