Pasar al contenido principal

DISPOSITIVOS, CIRCUITOS Y ARQUITECTURAS FIABLES Y DE BAJO CONSUMO PARA IOT

TEC2016-75151-C3-3-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE SEVILLA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Calibration of offset via bulk for Low-power HfO2 based 1T1R memristive crossbar Read-Out System

  • Mohan, Charanraj
  • Camuñas-Mesa, Luis A.
  • Vianello, Elisa
  • Periniolla, L.
  • Reita, Carlo
  • Rosa, José M. de la
  • Serrano-Gotarredona, Teresa
  • Linares-Barranco, Bernabé
Neuromorphic RRAM circuits typically need currents of several mA when many binary memristive devices are activated at the same time. This is due to the low resistance state of these devices, which increases the power consumption and limits the scalability. To overcome this limitation, it is vital to investigate how to minimize the amplitude of the read-out inference pulses sent through the crossbar lines. However, the amplitude of such inference voltage pulses will become limited by the offset voltage of read-out circuits. This paper presents a three-stage calibration circuit to compensate for offset voltage in the wordlines of a memristor-array read-out system. The proposed calibration scheme is based on adjusting the bulk voltage of one of the input differential pair MOSFETs by means of a switchable cascade of resistor ladders. This renders the possibility to obtain calibration voltage steps less than 0.1 mV by cascading a few number of stages, whose results are only limited by mismatch, temperature, electrical noise and other fabrication defects. The system is built using HfO2-based binary memristive synaptic devices on top of a 130-nm CMOS technology. Layout-extracted simulations considering technology corners, PVT variations and electrical noise are shown to validate the presented calibration scheme., This work was supported in part by the EU H2020 grants 644096 “ECOMODE” and 687299 “NeuRAM3”, by Spanish grants from the Ministry of Economy and Competitiveness – TEC2013-45638-C3-3-R (MARAGADA), TEC2015-63884-C2-1-P (COGNET) and TEC2016-75151-C3-3-R (TOGETHER) (with support from the European Regional Development Fund) and by the International Consortium of Nanotechnology of the Lloyd's Register Foundation under Grant Reference G0086. CSIC acknowledges CMP for design assembly and guidance.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced Linearity in FD-SOI CMOS Body-Input Analog Circuits – Application to Voltage-Controlled Ring Oscillators and Frequency-Based ΣΔ ADCs

  • Ahmadi-Farsani, Javad
  • Zúñiga-González, Virginia
  • Serrano-Gotarredona, Teresa
  • Linares-Barranco, Bernabé
  • Rosa, José M. de la
This paper investigates the use of the body terminal of MOS transistors to improve the linearity of some key circuits used to implement analog and mixed-signal circuits integrated in Fully Depleted Silicon on Insulator (FD-SOI) CMOS. This technology allows to increase the body factor with respect to conventional (bulk) CMOS processes. This effect is analyzed in basic analog building blocks - such as switches, simple-stage transconductors and Voltage-Controlled Ring Oscillators (VCROs). Approximated expressions are derived for the nonlinear characteristics and harmonic distortion of some of these circuits. As an application, transistor-level simulations of two VCRO-based ΣA modulators designed in a 28-nm FD-SOI CMOS technology are shown in order to demonstrate the benefits of the presented techniques., This work was supported in part by the EU Horizon 2020 Programme under Grant 687299 NeuRAM3 and in part by the Spanish Ministry of Economy and Competitiveness (with support from the European Regional Development Fund) under Contract TEC2016-75151-C3-3-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A 10-MHz BW 77.3-dB SNDR 640-MS/s GRO-Based CT MASH ΔΣ Modulator

  • Honarparvar, Mohammad
  • Rosa, José M. de la
  • Sawan, Mohamad
We present in this brief a novel multi-stage noise-shaping (MASH) 3-1 continuous-time (CT) delta-sigma modulator ( $\Delta \Sigma \text{M}$ ) with gated ring oscillator based quantizers (GROQs) in both stages of the cascade. The use of GROQs increases the linearity performance with respect to the conventional voltage controlled oscillator based quantizers (VCOQs) and allows a more robust extraction of the front-end stage quantization error in the time domain, thus making the proposed architecture more suitable to implement high-order expandable scaling-friendly MASH $\Delta \Sigma $ Ms, in which the back-end stages are implemented by mostly-digital GRO-based time-to-digital converters (TDCs). The circuit has been fabricated in a 65-nm CMOS technology with 1-V supply voltage, and it operates at 640-MHz sampling frequency to digitize 10-MHz signals. To the best of the authors' knowledge, this is the first reported experimental validation of a GRO-based CT MASH $\Delta \Sigma \text{M}$ , featuring a 79.8-dB signal to noise ratio (SNR) at -2.2-dBFS, a 77.3-dB signal to (noise + distortion) ratio (SNDR) at -4-dBFS and a dynamic range (DR) of 81.7 dB, with a power consumption of 12-mW. These metrics demonstrate state-of-the-art performance with a DR-based Schreier FOM of 170.9 dB., The authors acknowledge the Natural Sciences and Engineering Research Council of Canada for the support and CMC Microsystems for the design tools. This work was also partially supported by the Spanish Min. of Econ. and Comp. (and European RDF) under contract TEC2016-75151-C3-3-R., Peer reviewed