Pasar al contenido principal

ESTUDIO EXPERIMENTAL DE LA FUNCIONALIDAD Y SEGURIDAD DE LAS CARRETERAS CONVENCIONALES

TRA2013-42578-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Validation of Low-Cost Driving Simulator Based on Continuous Speed Profiles

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • Marín-Morales, Javier|||0000-0003-1271-2892
  • Pérez Zuriaga, Ana María|||0000-0002-8434-1106
  • García García, Alfredo|||0000-0003-1345-3685
  • Dols Ruiz, Juan Francisco|||0000-0003-1815-1360
[EN] The number of road safety studies that are based on driving simulators is growing significantly. The Polytechnic University of Valencia, Spain, developed a low-cost driving simulator for the assessment, training, and rehabilitation of drivers (SE2RCO). The main objective of this research was the validation of the driving simulator so that studies about road safety and highway geometric design that considered human factors could be performed. The validation was based on continuous speed profiles collected from 28 volunteers on a 30-km-long, two-lane rural road section. The same volunteers drove through the same road section built in SE2RCO. Speed data of 79 curves and 52 tangents were selected for the analysis. Comparison of the real and simulated speeds ensured the simulator's objective validity according to average and operating speeds. Two models were developed to predict field speeds from simulated speeds. Results showed that a simulated average speed lower than approximately 90 km/h was linked to a similar real average speed. For higher simulated speeds, the average speed in the real environment was lower than the simulated one. In addition, the actual operating speed was around 5 km/h lower than the operating speed in the driving simulator. Most volunteers assessed the quality and similarity of the virtual environment compared with the real world as medium or high and assessed the driving tasks similarly, thus achieving subjective validation of the simulator., The authors thank the Polytechnic University of Valencia, which subsidized the research project CONSIM-Desarrollo de un Modelo para la Evaluacion de la Consistencia del Diseno Geometric de Carreteras Convencionales Mediante Simuladores de Conduccion. The study presented here was also part of the research project titled CASEFU-Estudio Experimental de la Funcionalidad y Seguridad de las Carreteras Convencionales, which was subsidized by the Spanish Ministry of Economy and Competitiveness and the European Social Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Examination Free-Flow Speed Distribution on Two-Lane Rural Roads

  • García Jiménez, María Elena
  • Pérez Zuriaga, Ana María|||0000-0002-8434-1106
  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
[EN] Free-flow speed variation of passenger vehicles along a road segment is one of the most used factors in road safety studies, as a surrogate measure to evaluate road design consistency. Free-flow speed may be measured when a road segment is already built but must be estimated during the design phase. Several studies have been carried out to calibrate models to estimate free-flow speed, with geometric features as explanatory variables. Currently, most free-flow speed models focus only on mean speed or speed in particular percentiles, such as the 85th or 95th. Moreover, most studies have assumed normality in the free-flow speed distribution without checking this hypothesis. The main objective of this study was to analyze the free-flow speed distribution on two-lane rural road curves and tangents. The research focused on two main issues: determining whether speed data were normally distributed at a specific site and analyzing the behavior of the mean and standard deviation of speed on curves and tangents. The study was based on continuous operating speed profiles, which were obtained from a database of more than 16,000 vehicles/km. A total of 63 horizontal curves and 78 tangents were analyzed. According to the results, the normal distribution is not the best distribution in most cases for describing free-flow speeds. In 46 of the curves and 64 of the tangents, free-flow speed cannot be assumed to be normally distributed. Therefore, some other distributions should be tested in further research., The study presented in this paper is part of the research project CASEFU-Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales, subsidized by the Spanish Ministry of Economy and Competitiveness and the European Social Fund. In addition, the authors thank the Center for Studies and Experimentation of Public Works of the Spanish Ministry of Public Works for subsidizing the field data collection, and the Infrastructure and Transportation Department of the General Directorate of Public Works of the Valencian Government, the Valencian Provincial Council, and the Ministry of the Interior, especially the General Directorate of Traffic of Spain, for their cooperation in gathering the field data.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of horizontal geometric design of two-lane rural roads on vehicle CO2 emissions

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Pérez Zuriaga, Ana María|||0000-0002-8434-1106
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
[EN] In 2014, highway vehicles accounted for 72.8% of all Greenhouse Gases emissions from transportation in Europe. In the United States (US), emissions follow a similar trend. Although many initiatives try to mitigate emissions by focusing on traffic operations, little is known about the relationship between emissions and road design. It is feasible that some designs may increase average flow speed and reduce accelerations, consequently minimizing emissions. This study aims to evaluate the impact of road horizontal alignment on CO2 emissions produced by passenger cars using a new methodology based on naturalistic data collection. Individual continuous speed profiles were collected from actual drivers along eleven two-lane rural road sections that were divided into 29 homogeneous road segments. The CO2 emission rate for each homogeneous road segment was estimated as the average of CO2 emission rates of all vehicles driving, estimated by applying the VT-Micro model. The analysis concluded that CO2 emission rates increase with the Curvature Change Rate. Smooth road segments normally allowed drivers to reach higher speeds and maintain them with fewer accelerations. Additionally, smother segments required less time to cover the same distance, so emissions per length were lower. It was also observed that low mean speeds produce high CO2 emission rates and they increase even more on roads with high speed dispersions. Based on this data, several regression models were calibrated for different vehicle types to estimate CO2 emissions on a specific road segment. These results could be used to incorporate sustainability principles to highway geometric design., The study presented in this paper is part of the research project titled "CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales" (TRA2013-42578-P), subsidized by the Spanish Ministry of Economy, Industry, and Competitiveness and the European Social Fund. In addition, the authors would like to thank the Center for Studies and Experimentation of Public Works (CEDEX) of the Spanish Ministry of Public Works for subsidizing the field data collection and the General Directorate of Public Works and Transportation of the Valencian Government, to the Road Department of the Valencian Provincial Council, and to the Spanish Ministry of the Interior, especially the General Directorate of Traffic of Spain, for their cooperation in field data gathering. Finally, we would like to thank Professor Hesham A. Rakha, Virginia Tech (USA), for providing the VT-Micro model and assessing the authors in its use to obtain outcomes.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the Influence of Geometric Design Consistency on Vehicle CO2 Emissions

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
[EN] Highway vehicles driving on rural roads account for more than 50% of all CO2 emissions produced by the transportation sector in Europe. Although the policy measures to mitigate Greenhouse Gas emissions are increasing, these do not include policies aimed at reducing emissions by means of highway geometric design, which significantly influences drivers¿ speeds and accelerations and, consequently, plays a major role on fuel consumption and emissions. Therefore, the main objective of this research is to study the influence of the geometric design consistency on vehicle CO2 emissions. To do this, continuous speed data were collected on 47 homogeneous road segments by means of Global Positioning System devices. Vehicle CO2 emissions were estimated by applying the VT-micro model, whereas geometric design consistency was assessed considering different global consistency models. As a conclusion, vehicle CO2 emissions decreases as the consistency level of a homogeneous road segment increases. Specifically, a good consistency road segment has been found to present an emission rate 20-30% lower than a poor-consistent one. Therefore, the design of consistent roads allows, in addition to maximize road safety, to help to achieve more environmentally sustainable highways, reducing CO2 emission production., The presented study is part of the research project titled “CASEFU – Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales” (TRA2013-42578-P), subsidized by the Spanish Ministryof Economy, Industry, and Competitiveness and the European Social Fund. In addition, authors would like to thank Professor Hesham A. Rakha, Virginia Tech (USA), for providing the VT-Micro model and assessing the authors in its use to obtain outcomes.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Time-Based Calibration of the Inertial Operating Speed to Enhance the Assessment of the Geometric Design Consistency

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
  • Bella, Francesco
[EN] Road crashes are mainly caused by three concurrent factors: infrastructure, vehicle, and human factors. The interaction between the infrastructure and human factors leads to the concept of geometric design consistency. Recently, a global consistency model was developed based on the difference between the inertial operating speed profile and the operating speed profile. The first was defined as the weighted average operating speed of the previous road section based on distance, and represents drivers¿ expectancies, whereas the second represents road behavior. However, drivers¿ expectancies are related to short-term memory which declines gradually and depends on time. Thus, a time-based inertial operating speed would allow a more accurate estimation of the phenomenon. This research analyzes different periods of time and weighting distributions to identify how drivers¿ expectancies should be estimated. A set of 71 homogeneous road segments located in Italy were considered in the study. As a result, 25 seconds and a convex parabolic distribution should be used to calculate the inertial operating speed profile. This new way of estimating drivers¿ expectancies showed better results than those obtained based on distance. Finally, the proposed consistency model was compared with the previous models and was found to be able to assess more accurately the geometric design consistency. Therefore, the proposed consistency model is a useful tool for engineers to estimate the number of crashes so that they can incorporate road safety considerations into the geometric design of either new two-lane rural roads, or improving the existing ones., This research was subsidized by the Spanish Ministry of Economy, Industry, and Competitiveness through ‘‘Ayudas a la movilidad predoctoral para la realizacio´n de estancias breves en centros de I+ D 2015.’’ The study presented in this paper is also part of the research project entitled ‘‘CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales’’ (TRA2013-42578-P), subsidized by the Spanish Ministry of Economy, Industry, and Competitiveness and the European Social Fund. In addition, the authors would like to thank the ‘‘Azienda Nazionale Autonoma delle Strade’’ (ANAS) and the ‘‘Automobile Club Italia’’ (ACI), who provided traffic and crash data, respectively
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Calibration of Inertial Consistency Models on North Carolina Two-Lane Rural Roads

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
  • Findley, Daniel J.
[EN] Road crash occurrence is closely related to the geometric design consistency, which can be defined as how drivers¿ expectancies and road behavior fit. To this regard, the crash rate on a road segment increases as its consistency level decreases. To assess this phenomenon, inertial consistency models were recently developed. These models are based on the difference between the inertial operating speed, which represents drivers¿ expectancies, and the operating speed, which represents road behavior. The higher the difference between both speeds, the higher the likelihood of crash occurrence. This research aims to validate and calibrate these consistency models on American two-lane rural roads. For this, a total of 194 homogeneous road segments and 977 horizontal curves along 665 km in North Carolina (US) were used. As a result, the geometric design consistency was identified as a major factor of crash occurrence. The higher the difference between drivers¿ expectancies and road behavior, the higher the crash rate. Likewise, the greater the consistency level, the greater the percentage of horizontal curves without reported crashes. A Safety Performance Function was also calibrated to estimate the number of crashes on a road segment. Consistency thresholds were defined and tested to identify where these crashes are more likely to take place. Finally, the results obtained in this study were compared with those obtained previously on Spanish highways. To this regard, the crash rate on an American highway was 1.85 times greater than those observed on a Spanish highway under the same risk exposure and consistency conditions. Therefore, different tools were developed to enhance the assessment of road safety to the geometric design of both new two-lane rural roads and improvements of existing highways., This research was subsidized by the Spanish Ministry of Economy, Industry, and Competitiveness through “Ayudas a la movilidad predoctoral para la realización de estancias breves en centros de I+D 2017” (EEBB-I-17-12154). The study presented in this paper is also part of the research project titled “CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales” (TRA2013-42578-P), subsidized by the Spanish Ministry of Economy, Industry, and Competitiveness and the European Social Fund. In addition, the authors would like to thank the North Carolina Department of Transportation (NCDOT), which provided traffic and crash data.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modification of the Highway Capacity Manual two-lane highway analysis procedure for Spanish conditions

  • Moreno Chou, Ana Tsui
  • Llorca García, Carlos
  • Washburn, Scott
  • Bessa Jr., José Elievam
  • Hale, David K
  • García García, Alfredo|||0000-0003-1345-3685
[EN] The US Highway Capacity Manual (HCM) methodology is used in Spain to evaluate traffic operation and quality of service. The effect of passing manoeuvre on two-lane highway operational performance is considered through adjustment factors to average travel speeds and percent time spent following. The procedure is largely based on simulations in TWOPAS and passing behaviours observed during US calibrations in the 1970s. It is not clear whether US driving behaviour and vehicles' performance are comparable with Spanish conditions. The objective of this research is to adapt the HCM 2010 methodology to Spanish driver behaviour, for base conditions (i.e. no passing restrictions). To do so, TWOPAS was calibrated and validated based on current Spanish passing field data. The calibration used a genetic algorithm. The case study included an ideal two-lane highway with varying directional traffic flow rate, directional split and percentage of trucks. The updated methodology for base conditions is simpler than the current HCM 2010 and does not rely on interpolation from tables., The research was funded by the Spanish Ministry of Economy and Competitiveness (TRA2013-42578-P) and has been partially developed as a result of a mobility stay at the University of Florida funded by the Spanish Ministry of Economy and Competitiveness (EEBB-I-15-09970). The research was completed with the support of the FPI Research and Teaching Fellowship of the Spanish Ministry of Economy and Competitiveness (BES-2011-044612) and the TUM University Foundation Fellowship (TUFF) for international postdocs. We would like to thank Dr Lemke from the Bundesanstalt fur Straaenwesen (Federal Highway Research Institute) for providing the book from Brannolte and Holz [13] and the final reports of the research projects FE-Nr. 02.155G92 [12] and FE 16.0015/2009 [11].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Operating speed models for heavy vehicles on tangents of two-lane rural roads

  • González-Hernández, Brayan
  • Llopis-Castelló, David|||0000-0002-9228-5407
  • García García, Alfredo|||0000-0003-1345-3685
[EN] Road safety is one of the most important public health concerns in our society. In Spain, most road crashes involving heavy vehicles occur on two-lane rural roads. However, current road safety assessment procedures only rely on the analysis of the operating speed profile for passenger cars due to the few speed models available for heavy vehicles. Therefore, the main objective of this research was to analyze and model the free flow truck speeds on tangents of two-lane rural roads. To do this, the continuous speed profiles of 83 drivers travelling with their own heavy vehicle were collected by means of Global Positioning System tracking devices on 12 road sections. As a result, two different patterns were identified, which were associated with unloaded (35-54 kg/kW) and loaded (112-131 kg/kW) trucks. The most influential variables on truck speeds were tangent length, the grade of the tangent, the Curvature Change Rate of the tangent and its adjacent horizontal curves, and the speed of the preceding horizontal curve. Finally, several regression models were calibrated to predict the 85th percentile speeds for both loaded and unloaded trucks., The study presented in this paper is part of the research project titled CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales . This work was supported by the Spanish Ministry of Science, Innovation, and Universities and the European Social Fund (TRA2013-42578-P). In addition, the authors would like to thank the companies Agricultores de la Vega de Valencia (SAV) S.L., Saevi S.L., and Abonos Orgánicos Montagut (AOM) S.L., for their cooperation in field data gathering.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modelling vehicles acceleration during overtaking manoeuvres

  • Llorca Garcia, Carlos
  • Moreno, A. T.
  • García García, Alfredo|||0000-0003-1345-3685
[EN] Abstract: Overtaking manoeuvre is a key issue for two-lane rural roads. These roads should provide sufficient overtaking sight distance (OSD) at certain locations to allow faster vehicles to pass slower ones. However, overtaking requires occupying the opposing lane, which represents a serious safety concern. Severity of overtaking related crashes is very high, compared with other manoeuvres. The development of advanced driver assistance systems (ADAS) for overtaking is being a complex task. Only few systems have been developed, but are not still in use. This research incorporated accurate data of real manoeuvres to improve the knowledge of the phenomenon. The trajectory of the overtaking vehicles on the left lane was observed. An instrumented vehicle measured the overtaking time and distance, the abreast position, and the initial and final speed of 180 drivers that passed it during a field experiment. Six different kinematic models (such as uniform acceleration or linear variation of acceleration) were calibrated. Generally, drivers started to accelerate before changing to the opposing lane. These models may be applied to ADAS, to estimate OSD and to improve microsimulation models., Part of this research was included in the project 'Desarrollo de modelos de distancias de visibilidad de adelantamiento', with reference code TRA2010-21736 and subsidised by the Spanish Ministery of Economy and Competitivity. The authors also thank Prof Dr Sayed, from University of British Columbia, for his valuable review.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comparison of the highway safety manual predictive method with safety performance functions based on geometric design consistency

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • García García, Alfredo|||0000-0003-1345-3685
  • Findley, Daniel J.
[EN] Road safety is a major public health concern in our society. Effective road design and accurate safety analyses must be a component of programs focused on reducing and eliminating roadway injuries and deaths. Various methodologies exist to determine the expected number of crashes on rural two-lane rural roads. This research compares different procedures which allow for the estimation of the number of crashes on homogeneous road segments. In this effort, a total of 27 two-lane rural road sections located in North Carolina were considered, resulting in 59 homogeneous road segments composed of 350 horizontal curves and 375 tangents along 150 km of road. Four methods were applied to the selected roadways: the Highway Safety Manual predictive method, two jurisdiction-specific Safety Performance Functions (SPFs), and a SPF which includes a consistency parameter. This research found that the use of SPFs which incorporate a consistency parameter allows highway engineers to consider human factor impacts on road safety assessment. The use of a consistency parameter can also simplify the crash estimation process. Analysis methods which only included local geometric variables provided unreliable results due to the calibration of only the specific road elements instead of their relationship with other road elements along homogeneous road segments., This research was subsidized by the Spanish Ministry of Science, Innovation, and Universities through "Ayudas a la movilidad predoctoral para la realizacion de estancias breves en centros de I+D 2017" (EEBB-I-17-12154) and is part of the research project titled "CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales" (TRA2013-42578-P), subsidized by the above mentioned Spanish Ministry and the European Social Fund. In addition, the authors would like to thank the North Carolina Department of Transportation, which provided traffic and crash data.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of a global inertial consistency model to assess road safety on Spanish two-lane rural roads

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
[EN] The most important factors for road crash occurrence are infrastructure, vehicle, and human factors. In fact, infrastructure and its interaction with human factor have been thoroughly studied in recent years through geometric design consistency, which can be defined as how drivers¿ expectations and road behavior relate. Global consistency models were calibrated in the last decade to assess road safety on an entire homogeneous road segment. However, none of them include the underlying consistency phenomenon in their formulation. Recently, a new model was developed based on the difference between the inertial operating speed profile, which represents drivers¿ expectancies, and the operating speed profile, which represents road behavior. While the operating speed represents the estimated operating speed for every location along the road, the inertial operating speed aggregates for every station the operating speed effect along some distance already covered by drivers. The authors hypothesized that this `aggregation effect¿ was connected to drivers¿ expectancies, which proved to be true based on the best model fitted. However, the exact distance (or time) that should be considered to estimate the inertial operating speed still remains unknown. This paper aims to complete this model, analyzing how the inertial operating speed varies depending on different distances and periods of time. This impact is measured considering the reliability of the corresponding consistency model. The paper also covers how the inertial operating speed should be determined along the final distance or time. For this, a total of 184 homogeneous road segments along 650¿km in Spain were used., The study presented in this paper is part of the research project titled "CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales" (TRA2013-42578-P), subsidized by the Spanish Ministry of Economy, Industry and Competitiveness and the European Social Fund. In addition, the authors would like to thank the Department of Housing, Public Works and Spatial Planning of the Valencian Regional Government and the Traffic Department of the Spanish Government, which provided traffic and crash data, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

New consistency model based on inertial operating speed profiles for road safety evaluation

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
  • Bella, Francesco
[EN] Road crashes are mainly caused by three concurrent factors: infrastructure, vehicle and human factor. The interaction between infrastructure and human factor leads to the concept of geometric design consistency, which can be defined as how driver¿s expectations and road behavior fit. This paper presents a new global consistency model based on the difference between the inertial operating speed profile (Vi) and the operating speed profile (V85). The first one is calculated as the weighted average speed of the previous road section and represents drivers¿ expectations, whereas the second one represents road behavior. A set of 71 homogeneous two-lane rural road segments located in Italy were used in the calibration of the model. As a result, a Safety Performance Function based on this new consistency model was proposed in order to estimate the number of crashes in an entire road segment. Finally, the new model was compared with previous global consistency models, concluding that the new consistency parameter better explains the phenomenon than the previous ones. Therefore, the new consistency model is a useful tool for the engineers which allows estimating the number of crashes and incorporate road safety to the geometric design of both new two-lane rural roads and improvements of existing highways., This research was subsidized by the Spanish Ministry of Economy and Competitiveness through "Ayudas a la movilidad predoctoral para la realizacion de estancias breves en centros de I+D 2015." The study presented in this paper is also part of the research project titled "CASEFU-Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales" (TRA2013-42578-P), subsidized by the Spanish Ministry of Economy and Competitiveness and the European Social Fund. In addition, the authors would like to thank the Azienda Nazionale Autonoma delle Strade (ANAS) and the Automobile Club Italia (ACI), which provided traffic and crash data, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Calibration of the inertial consistency index to assess road safety on horizontal curves of two-lane rural roads

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Camacho-Torregrosa, Francisco Javier|||0000-0001-6523-7824
  • García García, Alfredo|||0000-0003-1345-3685
[EN] One of every four road fatalities occurs on horizontal curves of two-lane rural roads. To this regard, many studies have been undertaken to analyze the crash risk on this road element. Most of them were based on the concept of geometric design consistency, which can be defined as how drivers¿ expectancies and road behavior relate. However, none of these studies included a variable which represents and estimates drivers¿ expectancies. This research presents a new local consistency model based on the Inertial Consistency Index (ICI). This consistency parameter is defined as the difference between the inertial operating speed, which represents drivers¿ expectations, and the operating speed, which represents road behavior. The inertial operating speed was defined as the weighted average operating speed of the preceding road section. In this way, different lengths, periods of time, and weighting distributions were studied to identify how the inertial operating speed should be calculated. As a result, drivers¿ expectancies should be estimated considering 15¿s along the segment and a linear weighting distribution. This was consistent with drivers¿ expectancies acquirement process, which is closely related to Short-Term Memory. A Safety Performance Function was proposed to predict the number of crashes on a horizontal curve and consistency thresholds were defined based on the ICI. To this regard, the crash rate increased as the ICI increased. Finally, the proposed consistency model was compared with previous models. As a conclusion, the new Inertial Consistency Index allowed a more accurate estimation of the number of crashes and a better assessment of the consistency level on horizontal curves. Therefore, highway engineers have a new tool to identify where road crashes are more likely to occur during the design stage of both new two-lane rural roads and improvements of existing highways., The study presented in this paper is part of the research project titled "CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales" (TRA2013-42578-P), subsidized by the Spanish Ministry of Economy, Industry and Competitiveness and the European Social Fund. In addition, the authors would like to thank the Department of Housing, Public Works and Spatial Planning of the Valencian Regional Government and the Traffic Department of the Spanish Government, which provided traffic and crash data, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Speed Prediction Models for Trucks on Horizontal Curves of Two-Lane Rural Roads

  • Llopis-Castelló, David|||0000-0002-9228-5407
  • Pérez Zuriaga, Ana María|||0000-0002-8434-1106
  • García García, Alfredo|||0000-0003-1345-3685
  • González-Hernández, Brayan
[EN] Road safety is closely related to geometric design consistency, which is usually assessed by examining operating speed. Most consistency models only consider passenger car speeds, even though the interaction between passenger cars and heavy vehicles plays a pivotal role in road safety. This is due to the fact that there are too few models to estimate heavy vehicle speeds. This study aims to develop speed prediction models for heavy vehicles on horizontal curves of two-lane rural roads. To do this, continuous speed profiles were collected by using Global Positioning System (GPS) tracking devices on 11 road sections. Truck speeds were analyzed on 105 horizontal curves. The results showed that the radius of the horizontal curve and the grade at the point of curvature have a significant influence on heavy vehicle speeds. In this regard, vertical alignment only has a significant effect on truck speeds along upgrades. In addition, different trends were identified for loaded and unloaded trucks, so different speed models were calibrated for each of them. As a result, heavy vehicle speeds were adversely affected by grades greater than 3%. This phenomenon was larger for loaded trucks than for unloaded ones. Finally, the calibrated 85th and 15th percentile speed models were compared with those developed previously. As a conclusion, the use of the proposed models in this study was recommended on Spanish two-lane rural roads due mainly to the different characteristics of heavy vehicles around the world., The study presented in this paper is part of the research project titled ‘‘CASEFU - Estudio experimental de la funcionalidad y seguridad de las carreteras convencionales’’ (TRA2013-42578- P), subsidized by the Spanish Ministry of Economy, Industry, and Competitiveness and the European Social Fund. In addition, the authors would like to thank the companies SAV, SAEVI, and OAM, for their cooperation in field data gathering.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Operational Considerations of Passing Zones for Two-lane Highways: Spanish Case Study

  • Moreno Chou, Ana Tsui
  • Llorca Garcia, Carlos
  • Washburn, Scott
  • Bessa Jr., José Elievam
  • García García, Alfredo|||0000-0003-1345-3685
[EN] The U.S. Highway Capacity Manual (HCM 2010) methodology is used in Spain to evaluate traffic operation and quality of service. In two-lane undivided highways, the effect of limiting where drivers could pass slower vehicles, or passing restrictions, is considered through the percentage of no-passing zones. This measure does not account for how passing opportunities are distributed along the road. The objective of this research was to evaluate the effect percentage of no-passing zones and average passing zone length on two-lane, and incorporate them in the analysis methodology, if significant. The TWOPAS microsimulation program was calibrated and validated to the Spanish conditions. Passing restrictions had little effect on average traffic speed (ATS), with differences lower than 6 km/h between a segment of road with no passing restrictions and a segment of a road with 100% of length with passing restriction. Conversely, passing restrictions can increase percent time spent following (PTSF) up to 30%. Increasing the passing zone length beyond 2,000 m does not improve PTSF. The new models could be used to better estimate traffic operation on Spanish two-lane highways., The research was funded by the Spanish Ministry of Economy and Competitiveness [TRA2013-42578-P], and has been partially developed as a result of a mobility stay at the University of Florida funded by the Spanish Ministry of Economy and Competitiveness [EEBB-I-15-09970]. The research was completed with the support of the FPI Research and Teaching Fellowship of the Spanish Ministry of Economy and Competitiveness [BES-2011-044612] and the TUM University Foundation Fellowship (TUFF) for international postdocs. We would like to thank Dr. Lemke from the Bundesanstalt fur Strassenwesen (Federal Highway Research Institute) for providing the final report of the research project FE 16.0015/2009 (23). This work was supported by the German Research Foundation (DFG) and the Technical University of Munich (TUM) in the framework of the Open Access Publishing Program.