Pasar al contenido principal

DESARROLLO DE NUEVAS TECNOLOGIAS DESTINADAS A REDUCIR EL IMPACTO ACUSTICO DEL TRANSPORTE FERROVIARIO EN ENTORNOS URBANOS

TRA2013-45596-C2-1-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improved railway wheelset-track interaction model in the high-frequency domain

  • Martínez Casas, José|||0000-0001-5706-4951
  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • F. D. Denia|||0000-0003-4536-8610
[EN] As it is well known, there are various phenomena related to railway train-track interaction, some of them caused by the high frequency dynamics of the system, such as rolling noise when the vehicle runs over the track, as well as squeal noise and short-pitch rail corrugation for curved tracks. Due to these phenomena and some others unsolved so far, a large effort has been made over the last 40 years in order to define suitable models to study the train-track interaction. The introduction of flexibility in wheelset and rail models was required to have a more realistic representation of the wheel-rail interaction effects at high frequencies. In recently published train-track interaction models, the rails are modelled by means of Timoshenko beam elements, valid up to 1.5 kHz for lateral rail vibration and up to 2 kHz for vertical vibration. This confines the frequency range of validity for the complete train-track model to 1.5 kHz. With the purpose of extending the range of validity above 1.5 kHz, a 3D track model based on the Moving Element Method (MEM) is developed in this paper to replace the Timoshenko beam considered in earlier studies, adopting cyclic boundary conditions and Eulerian coordinates. The MEM approach considers a mobile Finite Element (FE) mesh which moves with the vehicle, so the mass of the rail flows with the vehicle speed but in the opposite direction through the mesh. Therefore, the MEM permits to fix the contact area in the middle of a finitely long track and to refine the mesh only around the contact area, where the forces and displacements will be more significant. Additionally, a modal approach is adopted in order to reduce the number of degrees of freedom of the rail model. Both strategies lower substantially the computational cost. Simulation results are presented and discussed for different excitation sources including random rail roughness and singularities such as wheel flats. All the simulation cases are carried out for a Timoshenko beam and a 3D MEM track model in order to point out the differences in the contact forces above the range of validity of the Timoshenko beam., The authors gratefully acknowledge the financial support of Ministerio de Economía y Competitividad and the European Regional Development Fund (project TRA2013-45596-C2-1-R), as well as Generalitat Valenciana (project Prometeo/2012/023) and Ministerio de Educación, Cultura y Deporte (project SP20140659) as part of Programa Campus de Excelencia Internacional.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Method for obtaining the wheel-rail contact location and its application to the normal problem calculation through CONTACT

  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • F. D. Denia|||0000-0003-4536-8610
  • Thompson, David J.
  • Squicciarini, Giacomo
[EN] This work presents a robust methodology for calculating inter-penetration areas between railway wheel and rail surfaces, the profiles of which are defined by a series of points. The method allows general three-dimensional displacements of the wheelset to be considered, and its characteristics make it especially suitable for dynamic simulations where the wheel-rail contact is assumed to be flexible. The technique is based on the discretization of the geometries of the surfaces in contact, considering the wheel as a set of truncated cones and the rail as points. By means of this approach, it is possible to reduce the problem to the calculation of the intersections between cones and lines, the solution for which has a closed-form expression. The method has been used in conjunction with the CONTACT algorithm in order to solve the static normal contact problem when the lateral displacement of the wheelset, its yaw angle and the vertical force applied in the wheelset centroid are prescribed. The results consist of smooth functions when the dependent coordinates are represented as a function of the independent ones, lacking the jump discontinuities that are present when a rigid contact model is adopted. Example results are shown and assessed for the normal contact problem for different lateral and yaw positions of the wheelset on the track., This work was supported by the financial contribution of the European Union’s Shift2Rail programme (RUN2Rail project, grant number 777564), the Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (projects TRA2013-45596-C2-1-R and TRA2017-84701-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the Falling Friction Effect on Rolling Contact Parameters

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • Vila Tortosa, María Paloma|||0000-0003-3399-231X
  • Alonso Pazos, Asier
[EN] The existence of a wheel rail friction coefficient that depends on the slip velocity has been associated in the literature with important railway problems like the curving squeal and certain corrugation problems in rails. Rolling contact models that take into account this effect were carried out through the so-called Exact Theories adopting an exact elastic model of the solids in contact, and Simplified Theories which assume simplified elastic models such as Winkler. The former ones, based on Kalker s Variational Theory, give rise to numerical problems; the latter ones need to adopt hypotheses that significantly deviate from actual conditions, leading to unrealistic solutions of the contact problem. In this paper, a methodology based on Kalker s Variational Theory is presented, in which a local slip velocity-dependent friction law is considered. A formulation to get steady-state conditions of rolling contact by means of regularisation of the Coulomb s law is proposed. The model allows establishing relationships in order to estimate the global properties (creepage velocities vs. total longitudinal forces) through local properties (local slip velocity vs. coefficient of friction) or vice versa. The proposed model shows a good agreement with experimental tests while solving the numerical problems previously mentioned., The authors acknowledge the financial contribution of the Spanish Ministry of Economy and Competitiveness through the Project TRA2013-45596-C2-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Finite element based acoustic analysis of dissipative silencers with high temperature and thermal-induced heterogeneity

  • F. D. Denia|||0000-0003-4536-8610
  • Sánchez-Orgaz, Eva María|||0000-0002-8864-3056
  • Martínez Casas, José|||0000-0001-5706-4951
  • Kirby, Ray
A mixed finite element model has been derived for the acoustic analysis of perforated dissipative silencers including several effects simultaneously: (1) High temperature and thermal gradients in the central duct and the outer absorbent material; (2) A perforated passage carrying non-uniform axial mean flow. For such a combination, the properties of sound propagation media and flow are inhomogeneous and vary with position. The material of the outer chamber can be modelled by its complex equivalent acoustic properties, which completely determine the propagation of sound waves in the air contained in the absorbent medium. Temperature gradients introduce variations in these properties that can be evaluated through a heterogeneous temperature-dependent resistivity in combination with material models obtained at room temperature. A pressure-based wave equation for stationary medium is then used with the equivalent density and speed of sound of the absorbent material varying as functions of the spatial coordinates. Regarding the central air passage, a wave equation in terms of acoustic velocity potential can be used to model the non-uniform moving medium since the presence of temperature variations introduce not only heterogeneous acoustic properties of the air but also a gradient in the mean flow velocity. The acoustic connection between the central passage and the outer chamber is given by the acoustic impedance of the perforated duct. This impedance depends on the heterogeneous properties of the absorbent material and the non-uniform mean flow, leading to a spatial variation of the acoustic coupling and also to additional convective terms in the governing equations. The results presented show the influence of temperature, thermal gradients and mean flow on the transmission loss of automotive silencers. It has been found that high temperature and thermal-induced heterogeneity can have a significant influence on the acoustic attenuation of an automotive silencer and so should be included in theoretical models. In some particular configurations it may be relatively accurate to approximate the temperature field by using a uniform profile with an average value, specially for low resistivity materials. It has been shown, however, that this is not always possible and attenuation overestimation is likely to be predicted, mainly for high radial thermal gradients and high material flow resistivities, if the temperature distribution is not taken into account., Authors gratefully acknowledge the financial support of Ministerio de Economia y Competitividad and the European Regional Development Fund (projects DPI2010-15412 and TRA2013-45596-C2-1-R), Generalitat Valenciana (project Prometeo/2012/023) and Universitat Politecnica de Valencia (PAID-05-12, project SP20120452).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

3D acoustic modelling of dissipative silencers with nonhomogeneous properties and mean flow

  • Sánchez-Orgaz, Eva María|||0000-0002-8864-3056
  • Denia, Francisco David
  • Martínez-Casas, José
  • Baeza, Luis
A finite element approach is proposed for the acoustic analysis of automotive silencers including a perforated duct with uniform axial mean flow and an outer chamber with heterogeneous absorbent material. This material can be characterized by means of its equivalent acoustic properties, considered coordinate-dependent via the introduction of a heterogeneous bulk density, and the corresponding material airflow resistivity variations. An approach has been implemented to solve the pressure wave equation for a nonmoving heterogeneous medium, associated with the problem of sound propagation in the outer chamber. On the other hand, the governing equation in the central duct has been solved in terms of the acoustic velocity potential considering the presence of a moving medium. The coupling between both regions and the corresponding acoustic fields has been carried out by means of a perforated duct and its acoustic impedance, adapted here to include absorbent material heterogeneities and mean flow effects simultaneously. It has been found that bulk density heterogeneities have a considerable influence on the silencer transmission loss., This work was supported by Ministerio de Economia y Competitividad (Projects DPI2010-15412 and TRA2013-45596-C2-1-R), Conselleria d'Educacio, Cultura i Esport (Project Prometeo/2012/023), and Programa de Apoyo a la Investigacion y Desarrollo (PAID-05-12 and Project SP20120452) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Point collocation scheme in silencers with temperature gradient and mean flow

  • F. D. Denia|||0000-0003-4536-8610
  • Sánchez-Orgaz, Eva María|||0000-0002-8864-3056
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • Kirby, R
This work presents a mathematical approach based on the point collocation technique to compute the transmission loss of perforated dissipative silencers with transversal temperature gradients and mean flow. Three-dimensional wave propagation is considered in silencer geometries with arbitrary, but axially uniform, cross section. To reduce the computational requirements of a full multidimensional finite element calculation, a method is developed combining axial and transversal solutions of the wave equation. First, the finite element method is employed in a two-dimensional problem to extract the eigenvalues and associated eigenvectors for the silencer cross section. Mean flow as well as transversal temperature gradients and the corresponding thermal-induced material heterogeneities are included in the model. In addition, an axially uniform temperature field is taken into account, its value being the inlet/outlet average. A point collocation technique is then used to match the acoustic fields (pressure and axial acoustic velocity) at the geometric discontinuities between the silencer chamber and the inlet and outlet pipes. Transmission loss predictions are compared favorably with a general three-dimensional finite element approach, offering a reduction in the computational effort., The authors gratefully acknowledge the financial support of Ministerio de Economia y Competitividad and the European Regional Development Fund (project TRA2013-45596-C2-1-R), as well as Generalitat Valenciana (project Prometeo/2012/023).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational performance of analytical methods for the acoustic modelling of automotive exhaust devices incorporating monoliths

  • F. D. Denia|||0000-0003-4536-8610
  • Martínez Casas, José|||0000-0001-5706-4951
  • Carballeira, Javier|||0000-0002-4179-8499
  • Nadal, Enrique|||0000-0002-2808-298X
  • Fuenmayor Fernández, Francisco-Javier|||0000-0003-3594-9593
[EN] The acoustic modelling of automotive exhaust devices, such as catalytic converters (CC) and diesel particulate filters (DPF), usually requires the use of multidimensional analytical and numerical techniques. The presence of higher order modes and three-dimensional waves in the expansion and contraction subdomains, as well as sound propagation within the monolith capillary ducts, can be considered through the finite element method (FEM), although this approach is traditionally thought to be very time consuming. With a view to overcome this limitation and to reduce the computational effort of the FEM, alternative modelling techniques are presented in the current work to speed up transmission loss calculations in exhaust devices incorporating monoliths. These approaches are based on the point collocation technique and the mode matching method. As shown in earlier studies, the sound attenuation of an exhaust device incorporating a monolith can be properly predicted if the latter is replaced by a plane wave four-pole transfer matrix providing a relationship between the acoustic fields at both sides of the monolithic region. Therefore, this work combines the presence of multidimensional higher order modes in the expansion and contraction regions with one-dimensional wave propagation within the capillary ducts of the central monolith. The point collocation technique and the mode matching method are applied to the compatibility conditions of the acoustic fields at all the subdomain interfaces to couple the solutions of the wave equation in the corresponding exhaust device subcomponents. For the particular case of rigid circular ducts, Bessel functions are considered as transversal pressure modes. The computational efficiency and accuracy of the results associated with the two analytical modelling techniques presented here are assessed, including the effect of the number of modes and collocation points, as well as their location. All the analytical approaches proposed in this work provide accurate predictions of the device attenuation performance and outperform the computational expenditure of a FE computation. Some differences are found, however, among the various analytical schemes in terms of computational speed and solution accuracy. From the results presented here, the mode matching method is the most efficient technique for the particular configurations under study, mainly due to the possibility of exploiting the orthogonality properties of the transverse pressure modes., This work has been supported by Ministerio de Economia y Competitividad and the European Regional Development Fund (project TRA2013-45596-C2-1-R), as well as Generalitat Valenciana (projects Prometeo/2016/007 and GV/2016/011 of Conselleria d'Educacio, Investigacio, Cultura i Esport).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A comprehensive model of the railway wheelset-track interaction in curves

  • Martínez Casas, José|||0000-0001-5706-4951
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • Di Gialleonardo, Egidio
  • Bruni, Stefano
Train-track interaction has been extensively studied in the last 40 years at least, leading to modelling approaches that can deal satisfactorily with many dynamic problems arising at the wheel/rail interface. However, the available models are usually not considering specifically the running dynamics of the vehicle in a curve, whereas a number of train-track interaction phenomena are specific to curve negotiation. The aim of this paper is to define a model for a flexible wheelset running on a flexible curved track. The main novelty of this work is to combine a trajectory coordinate set with Eulerian modal coordinates; the former permits to consider curved tracks, and the latter models the small relative displacements between the trajectory frame and the solid. In order to reduce the computational complexity of the problem, one single flexible wheelset is considered instead of one complete bogie, and suitable forces are prescribed at the primary suspension seats so that the mean values of the creepages and contact forces are consistent with the low frequency curving dynamics of the complete vehicle. The wheelset model is coupled to a cyclic track model having constant curvature by means of a wheel/rail contact model which accounts for the actual geometry of the contacting profiles and for the non-linear relationship between creepages and creep forces. The proposed model can be used to analyse a variety of dynamic problems for railway vehicles, including rail corrugation and wheel polygonalisation, squeal noise, numerical estimation of the wheelset service loads. In this paper, simulation results are presented for some selected running conditions to exemplify the application of the model to the study of realistic train-track interaction cases and to point out the importance of curve negotiation effects specifically addressed in the work., The authors acknowledge the financial contribution of the Spanish Ministry of Economy and Competitiveness through the project TRA2013-45596-C2-1-R.