Pasar al contenido principal

Desarrollo y diseño de materiales cerámicos mediante tecnologías no convencionales de microondas

RYC-2016-20915

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Incorporación
Convocatoria Ramón y Cajal
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Comparison in mechanical properties of zirconium titanate (ZrTiO4) synthetized by alternative routes and sintered by microwave (MW)

  • Guillén Pineda, René Miguel
  • Moreno, R.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
[EN] At present, ZrTiO4 nanopowders are used as a dielectric in the electroceramic field, applications of catalysis, microwave telecommunications devices, pigments, composites, etc. One of the most interesting applications is the potential as structural material and similar applications that require a high thermal resistance. However, all the properties of zirconium titanate are still a subject of interest for the industrial field.12 There are several routes of synthesis of ZrTiO4; among them is the sol-gel method and lyophilization. These methods have been used to make powders or small pieces of zirconium titanate. However, structural applications require materials in large quantities, so it is necessary to identify the differences between the methods of synthesizing and allowing the preparation of powders suitable for the generation of green materials for subsequent sintering.3 To develop a new generation of nanomaterials with microstructural differences it is necessary to innovate in the sintering process. Years ago, the use of conventional oven for sintering material was the usual procedure. Nowadays, non-conventional methods as Microwave sintering (MW) are a bright way to produce high dense materials, using heating rates in reduce dwell times and lower consumption using 70%-80% less energy. 4 This reactive sintering technique achieves excellent mechanical properties, homogeneous microstructure employing lower sintering temperatures. All these energy and economic advantages generate a new vision for the future on ceramic materials and their industrial production. The main objective of this study is to make a comparison of the mechanical properties of the materials synthesized by sol-gel method and lyophilization and sintered by microwaves., The authors would like to thank to the Generalitat Valenciana for financial support received for Santiago Grisolía program scholarship (GRISOLIAP/2018/168). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Low temperature degradation behaviour of 10Ce-TZP/Al2O3 bioceramics obtained by microwave sintering technology

  • Gil-Flores, Lorena
  • Rosa, Roberto
  • Veronesi, Paolo
  • Leonelli, Cristina
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Zirconia is one of the most used ceramics, especially for biomedical applications, due to its exceptional mechanical properties. However, it is commonly known that its properties can be diminished owing to a low temperature degradation (LTD). This phenomenon consists on a spontaneous phase transformation, from tetragonal to monoclinic, under certain conditions, which is accelerated when the samples are exposed under high levels of humidity at a temperature range between 20-300 ºC. In addition to the fact that the monoclinic phase presents worse mechanical properties than the tetragonal one, there is a volume change of 4% between phases that gives rise to defects in the material as microcracks. Due to this reason, zirconia prostheses failed catastrophically inside the human body between 1999 and 20011. Previous researches reveal that Al2O3 addition suppress the propagation of phase transformation2. Thus, the aim of the present work is to study the hydrothermal ageing of zirconia doped with ceria and toughened with alumina (10Ce-TZP/Al2O3) composite, which has been sintered by microwave employing two different frequencies: 2.45 and 5.8 GHz. Microwave heating technology is based on the absorption of electromagnetic radiation by the material, which allows the sample to be heated. So far, most microwave heating equipments use 2.45 GHz; accordingly, the novelty of this study is to employ a frequency of 5.8 GHz and to investigate its effect on LTD. LTD is carried out in an autoclaved in steam at 120 ºC and 1.2 bar, because these conditions accelerate the hydrothermal aging process3. In order to characterize the degraded samples, micro-Raman spectroscopy, AFM, nanoindentation technique and electronic microscopy have been performed. References 1. Norton, M. R., Yarlagadda, R., Anderson, G. H. J. Bone Joint Surg. Br., 2002, 84–B, 631–635. 2. Fabbri, P., Piconi, C., Burresi, E., Magnani, G., Mazzanti, F., Mingazzini, C. Dent. Mater., 2014. 3. Presenda, Á., Salvador, M. D., Moreno, R., Borrell, A. J. Am. Ceram. Soc., 2015, 98, 3680–3689., The authors thank the Generalitat Valenciana for the financial support provided to the PROMETEU/2016/040 project. A. Borrell is grateful to the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Comparison in mechanical properties of zirconium titanate (ZrTiO4) synthetized by alternative routes and sintered by microwave (MW)

  • Guillén Pineda, René Miguel
  • Borrell Tomás, María Amparo
  • Salvador Moya, Mª Dolores
  • Peñaranda Foix, Felipe Laureano
  • Moreno, Rodrigo
[EN] At present, ZrTiO4 nanopowders are used as a dielectric in the electroceramic field, applications of catalysis, microwave telecommunications devices, pigments, composites, etc. One of the most interesting applications is the potential as structural material and similar applications that require a high thermal resistance. However, all the properties of zirconium titanate are still a subject of interest for the industrial field.12 There are several routes of synthesis of ZrTiO4; among them is the sol-gel method and lyophilization. These methods have been used to make powders or small pieces of zirconium titanate. However, structural applications require materials in large quantities, so it is necessary to identify the differences between the methods of synthesizing and allowing the preparation of powders suitable for the generation of green materials for subsequent sintering.3 To develop a new generation of nanomaterials with microstructural differences it is necessary to innovate in the sintering process. Years ago, the use of conventional oven for sintering material was the usual procedure. Nowadays, non-conventional methods as Microwave sintering (MW) are a bright way to produce high dense materials, using heating rates in reduce dwell times and lower consumption using 70%-80% less energy. 4 This reactive sintering technique achieves excellent mechanical properties, homogeneous microstructure employing lower sintering temperatures. All these energy and economic advantages generate a new vision for the future on ceramic materials and their industrial production. The main objective of this study is to make a comparison of the mechanical properties of the materials synthesized by sol-gel method and lyophilization and sintered by microwaves., The authors would like to thank to the Generalitat Valenciana for financial support received for Santiago Grisolía program scholarship (GRISOLIAP/2018/168). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).