Pasar al contenido principal

Desarrollo y diseño de materiales cerámicos mediante tecnologías no convencionales de microondas

RYC-2016-20915

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Incorporación
Convocatoria Ramón y Cajal
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 34
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of relative humidity and low temperature hydrothermal degradation on fretting wear of Y-TZP dental ceramics

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Gil, Lorena
  • Presenda, Alvaro
  • Vleugels, Jozef
  • Moreno, Rodrigo
[EN] Dental pieces are subjected to constant friction due to grinding during mastication and mouth disorders such as bruxism. Therefore, wear resistance of Y-TZP materials used for dental prostheses must be investigated. In this work, the influence of humidity and low temperature hydrothermal degradation (LTD) in 3Y-TZP ceramics subjected to fretting has been evaluated. A 100% r.h. reduces the effects of wear due to the lubricative effect of water, compared to those at ambient r.h. COF, wear volume and damage are considerably lowered at a r.h. of 100%. Exposure to degradation conditions for 25 h increased the vulnerability to wear damage of LAVA grade Y-TZP sintered at 1400 degrees C since the critical grain size of 300 nm was exceeded., This work has been supported by the Spanish Ministry of Economy and Competitiveness MINECO by MAT2015-67586-C3-R project and RyC contract (RYC-2016-20915), and the Generalitat Valenciana by PROMETEO/2016/040 project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structure Features and Properties of Graphene/Al2O3 Composite

  • Klyatskina, E.
  • Grigoriev, Evgenii
  • Zholnin, Aleksander
  • Stolyarov, V.V.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[EN] Since its discovery, graphene has attracted worldwide attention in the scientific community owing to its unique combination of properties. Thus, graphene is an ideal second phase to improve the structure and properties of metal, ceramic and polymer composite materials. This work presents a comparative study of two types of alumina-graphene composites fabricated with two sizes of delta-Al2O3 powders, nanometer and submicrometer, reinforced by graphene nanoplatelets (GNPs) and consolidated with the spark plasma sintering technique. The microstructure, mechanical and tribological properties of Al2O3-GNPs composites are influenced by the grain size of the ceramic matrix. Hardness values improve notably. The maximum value reached was 27.4 GPa for a composite fabricated with nanometric alumina powders, which is about 27 % higher than that of the Al2O3 monolithic material. Also, the methodology of powder mixing has a fundamental importance in obtaining materials with high-level properties., This work has been supported by the Competitiveness Program National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Russian Ministry of Education and Science No. 02. A 03.21.0005; the Russian Science Foundation No16 - 19 - 10213; the Spanish Ministry of Economy and Competitiveness project MAT2015 - 67586-C3-R. E. Klyatskina acknowledges the Valencian Government for her Post-Doc. Contract APOSTD/2014/046 and A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her contract RYC2016 - 20915.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Alumina/molybdenum nanocomposites obtained by colloidal synthesis and spark plasma sintering

  • Fernández-González, Daniel
  • Suárez-Menéndez, Marta
  • Piñuela-Noval, Juan
  • Díaz, Luís Antonio
  • Gómez-Rodríguez, Carlos
  • García Quiñonez, Luís V.
  • Fernández-Valdés, Adolfo
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Alumina/molybdenum nanocomposites were prepared by colloidal synthesis from alumina powder and molybdenum (V) chloride using ethanol as dispersion medium. Modified alumina was calcined at 450 ¿C in air atmosphere to remove chlorides, and then treated in a tubular furnace at 850 ¿C under Ar/H2 to reduce the MoO3 formed in the previous stage and obtain Al2O3 with molybdenum nanoparticles on the surface. Three different molybdenum contents were proposed (1, 5 and 10 wt % Mo), and pure alumina was used as reference, that were sintered by spark plasma sintering (SPS) under vacuum atmosphere at 1400 ¿C for 3 min with an applied pressure of 80 MPa. Composites were characterized by microstructure, hardness, toughness, and three-point bending test. The presence of molybdenum nanoparticles resulted in a fine-grained structure promoted by the presence of molybdenum at grain boundaries and triple points, as well as by the utilization of the SPS equipment. Hardness is at least a 20% greater and fracture toughness 30% larger in the composites than in the monolithic alumina., Daniel Fernandez-Gonzalezacknowledges the grant (Juan de la Cierva-Formacion program) FJC2019-041139-I funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia e Innovacion, Agencia Estatal de Investigacion). The authors also acknowledge the financial support received from FICYT (IDI/2021/000106). Juan Pinuela Noval acknowledges the Programa Severo Ochoa of Grants for Research and Teaching of the Principality of Asturias for the funds received for the elaboration of the Ph. D. Thesis (Ref: BP20 041).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Comparison in mechanical properties of zirconium titanate (ZrTiO4) synthetized by alternative routes and sintered by microwave (MW)

  • Guillén Pineda, René Miguel
  • Moreno, R.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
[EN] At present, ZrTiO4 nanopowders are used as a dielectric in the electroceramic field, applications of catalysis, microwave telecommunications devices, pigments, composites, etc. One of the most interesting applications is the potential as structural material and similar applications that require a high thermal resistance. However, all the properties of zirconium titanate are still a subject of interest for the industrial field.12 There are several routes of synthesis of ZrTiO4; among them is the sol-gel method and lyophilization. These methods have been used to make powders or small pieces of zirconium titanate. However, structural applications require materials in large quantities, so it is necessary to identify the differences between the methods of synthesizing and allowing the preparation of powders suitable for the generation of green materials for subsequent sintering.3 To develop a new generation of nanomaterials with microstructural differences it is necessary to innovate in the sintering process. Years ago, the use of conventional oven for sintering material was the usual procedure. Nowadays, non-conventional methods as Microwave sintering (MW) are a bright way to produce high dense materials, using heating rates in reduce dwell times and lower consumption using 70%-80% less energy. 4 This reactive sintering technique achieves excellent mechanical properties, homogeneous microstructure employing lower sintering temperatures. All these energy and economic advantages generate a new vision for the future on ceramic materials and their industrial production. The main objective of this study is to make a comparison of the mechanical properties of the materials synthesized by sol-gel method and lyophilization and sintered by microwaves., The authors would like to thank to the Generalitat Valenciana for financial support received for Santiago Grisolía program scholarship (GRISOLIAP/2018/168). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Lead-free low-melting-point glass as bonding agent for TiO2 nanoparticles

  • Lopez-Esteban, S.
  • Cabal, B.
  • Bartolomé, J.F.
  • Fernandez, A.
  • Faraldos, M.
  • Bahamonde, A.
  • Moya, J.S.
  • Pecharroman, C.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] This work is a study of the properties of TiO2-anatase nanoparticles attached by a low-melting point inorganic glass (530 degrees C). Unlike other low-melting glasses, this composition does not contain any toxic metal. Likewise, it shows an excellent wettability on ceramic nanoparticles. A small addition of 5 vol% of glass remarkably enhances the mechanical strength of the composites with respect to pure TiO2 calcined at the same temperature, becoming twice this value. Self-cleaning properties analyzed using the methylene blue 385 nm UV-A photodegradation test showed that, after different UV-light periods, the photo-efficiency of TiO2-anatase was not altered by the presence of this glass., This work was supported by CSIC under grant 201960E103 and by the Spanish Ministry of Science Innovation and Universities (MCIU/AEI/FEDER, UE) under award RTI2018-094958-B-I00. Dr. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microwave sintering study of strontium-doped lanthanum manganite in a single-mode microwave with electric and magnetic field at 2.45 GHz

  • Moratal, Sheila
  • Moreno, Rodrigo
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] The objective of this work is to study the changes in the physical and mechanical properties of strontium-doped lanthanum manganite (LSM) material and LSM-YSZ (ZrO2 doped with 8 mol% yttria) composite, obtained by colloidal processing and sintered by 2.45 GHz microwave sintering at 1200 and 1300 ¿C using two different single-mode cavities. One circular cavity with TE111 mode that has maximum in the electric field (E-field) and one rectangular cavity with TE102 mode that has maximum in the magnetic field (H-field). As compared to conventional sintering at 1300 and 1400 ¿C, the microwave-heated samples exhibited a denser structure for shorter sintering times. LSM-based materials showed higher heating behavior in H-field, which translates into higher energy absorption. This fact can be attributed to an electromagnetic pressure induced by the combined effect of current loops subjected to H-field. Therefore, the interaction between the material and the electromagnetic waves depends on the dominant field of them., This research was funded by the project of the Spanish Ministry of Science and Innovation: RTI2018-099033-B-C32&C33 and RYC2016-20915, and Generalitat Valenciana (BEST/2021/084, BEST/2021/082).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Molten salt attack on multilayer and funcionally-graded YSZ coating

  • Carpio-Cobo, Pablo
  • Navarro-López, Lucia
  • Sánchez, E.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Thermal barrier coatings have been extensively studied in the last years in order to increase the operational temperature of the current gas turbines as well as to improve the coating lifetime. Many coating characteristics must be met to achieve these requirements (low thermal conductivity, high thermal fatigue resistance...); therefore, complex systems have been engineered for these purposes. One of the possibilities to optimise the different properties deals with the design of multilayer or functionally-graded coatings where various types of microstructures with different characteristics are combined. One of the most important cause of gas turbines degradation relates to the attack of different type of particles which are suspended in the atmosphere (sand, fly ash...). These solid particles are molten at the operational temperatures and then, the molten salts chemically react with the coating. For this reason, the present research was focused on this type of attack. In the present work, the molten salt attack of various YSZ coatings with multilayer and functionally-graded design was addressed. Two different type of microstructures were specifically combined for this design: the APS coating microstructure obtained from conventional (microstructured) powder and a bimodal structure with nanozones obtained from nanostructured feedstock. Besides, different salts were used to simulate different attack environments (desert sand and volcanic fly ash). Findings show that nanozones act as barrier against the penetration of molten salts toward deeper layer. However, a layer formed by nanozones can detach when the salt attack is too aggressive. Hence, functionally-graded coatings, where two types of microstructures are combined through the whole coating, become ideal to diminish the molten salt attack., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2015-67586-C3-R) as well as A. Borrell and L. Navarro thanks for their post-doc (RyC-2016-20915) and pre-doc (BES-2016-077792) contracts respectively. P. Carpio acknowledges the Valencia Government for his post-doc contract (APOSTD/2016/040).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of green body density on the properties of graphite-molybdenum-titanium composite sintered by spark plasma sintering

  • Suárez, Marta
  • Fernández-González, D.
  • Gutiérrez-González, C.F.
  • Díaz, L.A.
  • Moya, J.S.
  • Torrecillas, R.
  • Fernández, A.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] This manuscript contains a study about the effect of the degree of compaction of green parts on the properties of a Graphite-5.5 vol. % Molybdenum- 0.6 vol. % Titanium composite obtained by SPS. The composite, sintered at 2000 degrees C, below the eutectic temperature of the C-Mo system (2584 degrees C), exhibits different properties depending on the direction of the applied pressure. On this matter, properties are significantly better in-plane than in the other directions. Samples uniaxially pressed at 60 MPa to obtain the green compact exhibit highly improved properties which are competitive with those obtained under extreme conditions, i.e. uniaxial pressure at 300 MPa and sintering temperature > 2000 degrees C in presence of a liquid phase. The composite production process could be easier scaled up to the industrial level. Thus, this graphite-molybdenum-titanium composite could be used as heat sink in a panoply of applications., This research was funded by the Spanish Ministry of Science and Innovation. Call Programa Estatal de I+D+i Orientada a los Retos de la Sociedad [RTI2018-102269-B-I00] . Daniel Fernandez-Gonzalez acknowledges the grant (Juan de la Cierva-Formacion program) FJC2019-041139-I funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia e Innovacion, Agencia Estatal de Investigacion). Authors are grateful to Ainhoa Macias San Miguel from Nano-materials and Nanotechnology Research Center (CINN) for providing technical assistance.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Mo content on the properties of graphite MoC composites sintered by spark plasma sintering

  • Suárez, Marta
  • Fernández-González, Daniel
  • Díaz, Luís Antonio
  • Piñuela-Noval, Juan
  • Moya, José Serafin
  • Torrecillas, Ramón
  • Fernández, Adolfo
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Graphite-molybdenum-titanium powders prepared by colloidal processing technique were sintered by Spark Plasma Sintering (SPS). This material is proposed in this manuscript due to its potential interest as heat sink. The influence of the molybdenum content (2.5, 5.0 and 10.0 vol.%) on the thermal, electrical, and mechanical properties of the composite are studied to define the composite with the best properties. Thermal, electrical, and mechanical properties of the composite graphite¿10 vol.% Mo¿1 vol.% Ti (that are composites of graphite with molybdenum and titanium carbides after sintering) are significantly better than those ofthe composites with lower molybdenum contents (2.5 vol.% and 5 vol.%). This way, flexural strength, electrical conductivity, and thermal conductivity are 1.5, 7.8 and 18 times greater, respectively, than in the composite graphite¿2.5 vol.% Mo¿1 vol.% Ti. In the case of comparing with the composite graphite¿5 vol.% Mo¿1 vol.% Ti, flexural strength, electrical conductivity, and thermal conductivity are 1.2, 5.1 and 3.2 greater in the composite graphite¿10 vol.% Mo¿1 vol.% Ti, respectively., This research was funded by the Spanish Ministry of Science and Innovation. Call Programa Estatal de I+D+i Orientada a los Retos de la Sociedad (RTI2018-102269-BI00). Daniel Fernández-González acknowledges the grant (Juan de la Cierva-Formación program) FJC2019-041139-I funded by MCIN/AEI/ 10.13039/501100011033 (Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación). Amparo Borrell acknowledges for her RYC-2016-20915. Juan Pinuela Noval acknowledges the Programa Severo Ochoa of Grants for Research and Teaching of the Principality of Asturias for the funds received for the elaboration of the Ph.D. Thesis (Ref: BP20 041).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Low temperature degradation behaviour of 10Ce-TZP/Al2O3 bioceramics obtained by microwave sintering technology

  • Gil-Flores, Lorena
  • Rosa, Roberto
  • Veronesi, Paolo
  • Leonelli, Cristina
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Zirconia is one of the most used ceramics, especially for biomedical applications, due to its exceptional mechanical properties. However, it is commonly known that its properties can be diminished owing to a low temperature degradation (LTD). This phenomenon consists on a spontaneous phase transformation, from tetragonal to monoclinic, under certain conditions, which is accelerated when the samples are exposed under high levels of humidity at a temperature range between 20-300 ºC. In addition to the fact that the monoclinic phase presents worse mechanical properties than the tetragonal one, there is a volume change of 4% between phases that gives rise to defects in the material as microcracks. Due to this reason, zirconia prostheses failed catastrophically inside the human body between 1999 and 20011. Previous researches reveal that Al2O3 addition suppress the propagation of phase transformation2. Thus, the aim of the present work is to study the hydrothermal ageing of zirconia doped with ceria and toughened with alumina (10Ce-TZP/Al2O3) composite, which has been sintered by microwave employing two different frequencies: 2.45 and 5.8 GHz. Microwave heating technology is based on the absorption of electromagnetic radiation by the material, which allows the sample to be heated. So far, most microwave heating equipments use 2.45 GHz; accordingly, the novelty of this study is to employ a frequency of 5.8 GHz and to investigate its effect on LTD. LTD is carried out in an autoclaved in steam at 120 ºC and 1.2 bar, because these conditions accelerate the hydrothermal aging process3. In order to characterize the degraded samples, micro-Raman spectroscopy, AFM, nanoindentation technique and electronic microscopy have been performed. References 1. Norton, M. R., Yarlagadda, R., Anderson, G. H. J. Bone Joint Surg. Br., 2002, 84–B, 631–635. 2. Fabbri, P., Piconi, C., Burresi, E., Magnani, G., Mazzanti, F., Mingazzini, C. Dent. Mater., 2014. 3. Presenda, Á., Salvador, M. D., Moreno, R., Borrell, A. J. Am. Ceram. Soc., 2015, 98, 3680–3689., The authors thank the Generalitat Valenciana for the financial support provided to the PROMETEU/2016/040 project. A. Borrell is grateful to the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Synthesis and processing of improved graphite-molybdenum-titanium composites by colloidal route and spark plasma sintering

  • Suárez, M.
  • Fernández-González, D.
  • Díaz, L.A.
  • Moya, J.S.
  • Fernández, A.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Graphite-molybdenum-titanium composites might attract significant interest as heat sinks for different sector applications due to their excellent thermal, electrical and mechanical properties. This type of composites was already studied but following the powder metallurgy and spark plasma sintering (SPS) route. The aim of the present investigation is to study a new route of fabrication of these composites to improve their properties: colloidal synthesis and SPS process. The results obtained for graphite-10 vol% Mo-1 vol% Ti composites prepared by both routes are compared. It has been proved that the properties of the composites are significantly improved by the colloidal route compared with the powder metallurgy route, i. e. electrical conductivity by a factor of 3, thermal properties by a factor of 8 and bending strength by a factor of 4., This research was funded by the Spanish Ministry of Science and Innovation. Call Programa Estatal de I+D+i Orientada a los Retos de la Sociedad [RTI2018-102269-B-I00] . This research was also supported by a Juan de la Cierva Formacion grant from the Spanish Ministry of Sci-ence and Innovation (MCINN) to Daniel Fernandez-Gonzalez [FJC2019-041139-I] . A. Borrell acknowledges for her RYC-2016-20915. Authors are grateful to Ainhoa Macias San Miguel from Nanomaterials and Nanotechnology Research Center (CINN) for providing technical assistance.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fabrication and characterization of Nb2O5-doped 3Y-TZP materials sintered by microwave technology

  • Guillén-Pineda, René M.
  • Gutiérrez-González, Carlos F.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] The purpose of this research is focused on the manufacture and characterization of a partially stabilized zirconia ceramic with 3 mol% of Yttria and doped with .5 and 1.5 mol% of Nb2O5 to analyze the influence of doping, with the purpose of improving the properties before hydrothermal degradation. In the first instance, the microwave sintering process was used for the consolidation of this material, then the physical and mechanical properties were characterized. Together, the results obtained by the conventional sintering process were compared. A low hydrothermal degradation study (LTD) is presented at low temperatures in which possible changes in the mechanical properties of the ceramic materials are analyzed and its influence on the phase transformation that zirconia may present is observed. The mechanical properties were evaluated through hardness, fracture toughness, and Young's modulus tests. Likewise, their density was analyzed, and microstructure was characterized by FESEM. It was found that the microwave-sintered samples at 1200 degrees C exhibited superior properties of toughness than even samples sintered by conventional methods at higher temperatures (1400 degrees C). The sample of 3Y-TZP with 1.5 mol% Nb2O5 sintered by microwave with <.2% of porosity achieved a maximum fracture toughness value around 40% higher than the dense monolithic 3Y-TZP material., Santiago Grisolia program, Grant/Award Number: GRISOLIAP/2018/168; Ministry of Science, Innovation and Universities (Spain), Grant/Award Numbers: RTI2018-099033-B-C32, RYC-2016-20915
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tribological behavior of TZ4YS-MoSi2 composites obtained by Spark Plasma Sintering

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Bloem, Carlos
  • Gutiérrez-González, Carlos F.
  • Alcázar, Carmen
  • Moreno, Rodrigo
[EN] The aim of this work was to evaluate the role of MoSi2 content (5, 10, 15 wt%) in the mechanical and tribological behavior of TZ4YS-MoSi2 composites obtained by colloidal processing and spark plasma sintering (SPS) at 1500 degrees C. Firstly, the densification of TZ4YS-MoSi2 composite and the shrinkage-rate curves by SPS applying 80 MPa from 1300 degrees C to 1500 degrees C is studied. The hardness and fracture toughness values confirmed that up to 99.9% densification is gradually reached with increasing MoSi2 percentage. Secondly, pin-on-disk tribological tests at different distances (1, 5, 15 and 2000 m) with Al2O3 as counterpart were performed to record the behavior of the materials in the initial and final stages of wear. The MoSi2 content was associated to the beginning of the transition from mild to severe wear, higher the amount of MoSi2 faster is the transition. This behavior was correlated with MoSi2 content, which aids the formation of a tribolayer., The authors would like to thank the Ministry of Science, Innovation and Universities (Spain) for its financial through the projects RTI2018-099033-B-C32&C33 (MCIU/AEI/FEDER, UE) and RYC-2016-20915.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fast-low temperature microwave sintering of ZrSiO4-ZrO2 composites

  • Moratal, Sheila
  • Rosado, Eduardo
  • Moreno, Rodrigo
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Today, many industrial applications require components that work under extreme conditions, especially at very high temperatures (>1200 & DEG;C) for a long time. An excellent combination of properties such as low thermal conductivity, low coefficient of thermal expansion and high chemical resistance are required for such applications. Advanced ceramic materials based on zircon-zirconia composites (ZrSiO4-ZrO2) possess these properties, thus making them attractive for, i.e., high-level radioactive waste immobilisation. The main drawback of these materials are the high temperatures and long residence times required to sinter them and obtain high densities, which entails high energy consumption and costs. Therefore, non-conventional microwave sintering is a very powerful and efficient technique capable of reducing sintering temperatures and holding times. The objective of this study is to evaluate the microwave sinterability of zircon-zirconia powders obtained by colloidal methods (80-20 vol% and 20-80 vol% ZrSiO4-ZrO2). A stability study of the phases present was carried out by X-ray diffraction and the mechanical and microstructural properties were evaluated in order to obtain the best materials with outstanding final properties., Grants PID2021-128548OB-C21 and PID2021-124521OB-100 funded by MCIN/AEI/10.13039/501100011033 and "ERDF A way of making Europe". Grant CIGE/2021/076 funded by Generalitat Valenciana. E. Rosado acknowledges a MCIN/AEI pre -doctoral fellowship PRE2019-091092.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructure and mechanical properties of 4YTZP-SiC composites obtained through colloidal processing and Spark Plasma Sintering

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Navarro, Lucia
  • Gutiérrez-González, Carlos F.
  • Alcazar, Carmen
  • Moreno, Rodrigo
[ES] En este estudio se investigaron las propiedades microestructurales y mecánicas de los composites de circona reforzados con carburo de silicio (SiC) obtenidos mediante procesamiento coloidal y sinterización por descarga eléctrica (spark plasma sintering [SPS]). Se prepararon mezclas de circona dopada con 4 %mol de itria (4YTZP) y SiC con porcentajes del 15 y 20% en peso mediante procesamiento coloidal y liofilización para garantizar la homogeneidad de los polvos, posteriormente se sinterizaron por SPS a temperaturas de 1300 a 1400 °C para obtener composites densos. La técnica de SPS permite controlar el tiempo y la velocidad de sinterización e impide la oxidación del SiC para garantizar una mayor reproducibilidad. La microestructura de los composites ha revelado algunos defectos durante la sinterización debido a las diferencias de coeficiente de expansión térmica entre la 4YTZP y el SiC. Por otro lado, se estudiaron las propiedades mecánicas como la dureza Vickers, el módulo de Young y la resistencia a la flexión. En comparación con el material monolítico de 4YTZP sinterizado a 1400 °C, los composites presentan mejores valores de resistencia a la fractura (~ 588 MPa y ~ 492 MPa, con un 15 y un 20% en peso de SiC, respectivamente). También se ha demostrado que las partículas de SiC actúan como centro de absorción de propagación de grietas., [EN] Bulk composites of silicon carbide reinforced zirconia were obtained through colloidal processing and spark plasma sintering, and their microstructural and mechanical properties were investigated. Mixtures of powders of 4 mol% yttria-doped zirconia and silicon carbide, with percentages of 15 and 20 wt% of silicon carbide, were prepared by colloidal processing and freeze-drying to guarantee the homogeneity of powders, and sintered by SPS at temperatures ranging from 1300 to 1400 degrees C to obtain dense composites. The spark plasma sintering technique makes it possible to control sintering energy and speed, and impedes the oxidation of silicon carbide to ensure larger reproducibility. The microstructure of the composites reveals that some defects arise during sintering due to the differences of coefficient of thermal expansion between zirconia and silicon carbide. Mechanical properties were studied, such as Vickers hardness, Young's modulus, and bending strength. Compared with 4YTZP monolithic material, composites have better fracture strength values (similar to 588 MPa and 492 MPa, for 15 wt% and 20 wt% of silicon carbide, respectively) when sintered at 1400 degrees C. It is also demonstrated that silicon carbide particles act as an absorption centre for propagating cracks., The authors would like to thank the financial support received of the Spanish Ministry of Economy and Competitiveness (MINECO) under project MAT201567586C3R. A. Borrell acknowledge MINECO for RYC-2016-20915.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

From freeze-dried precursors to microwave sintered Al2O3-ZrO2 composites

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Gil-Flores, Lorena
  • Guillén-Pineda, René Miguel
[EN] Homogeneous Al2O3-Zr0.91Y0.09O1.955 (65-35 mol%) nanopowders have been prepared in a wide temperature range (from 1073 to 1573 K) by thermal decomposition of amorphous precursors, made previously by freeze-drying of appropriate solutions in air Electron microscopy images show that, whereas at low temperatures (973 K) pseudo-spherical particles constituted of Al2O3 and Zr0.91Y0.09O1.955 grains are observed (similar to 38nm), at high temperatures (1573 K) a homogeneous dispersion of nanocrystalline ZrO2-based grains (similar to 186 nm) is dispersed in the sintered Al2O3 matrix. The comparison between phase and microstructure evolution in these samples clearly indicates that the disorder at the atomic scale in the precursor makes the attainment of higher temperatures necessary for nucleation and growth of both phases. Finally, a selected material was sintered in a mono-mode microwave device at 2.45 GHz in air at 1573 and 1673 K. This fast-microwave technology allows fabrication of composites with high densities (similar to 99% TD) and excellent mechanical properties, such as hardness and Young's modulus reaching 25.6 GPa and 358 GPa, respectively., The authors would like to thank to the Generalitat Valenciana for financial support received for the project PROMETEO/2016/040 and Santiago Grisolia program scholarship (GRISOLIAP/2018/168). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dielectric, mechanical and thermal properties of ZrO2¿TiO2 materials obtained by microwave sintering at low temperature

  • Guillén, René M.
  • Recio, Paloma
  • Moreno, Rodrigo
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] The sinterability of 3Y-TZP/TiO2 materials using micrometre-sized ZrO2 and nanometre-sized TiO (16 wt%) by one-step fast microwave sintering at low temperature (1200¿1300C) was investigated. Firstly, in situ detailed analysis of the dielectric properties of the material with temperature was carried out in order to measure the capacity of the material to transform microwave energy into heat. Another related parameter associated to microwave sintering is the penetration depth of the microwave radiation into the material, which showed great homogeneity from 400¿C. Secondly, the effect of sintering conditions on microstructure, density, hardness and coefficient of thermal expansion was evaluated. The X-ray diffraction study and microstructural characterization demonstrate that it is possible to obtain fully dense pieces (>99%) by microwave sintering, a condition yielding to a coarse-grained (~1¿2 ¿m), quite hard (~13.7 GPa) 3Y-TZP/TiO material. However, the most important feature is the significant reduction of the thermal expansion coefficient as compared to that of 3Y- TZP. In addition, the results from conventional sintering at 1400¿1500 C with 2 and 6 h of dwell time are examined and compared. The materials obtained at 1500¿C showed high density with grain size and hardness similar to those obtained by microwave but with a dramatic difference in the power consumption of the sintering cycle, since the materials obtained by microwave used a maximum absorbed power of 120 W and a heating cycle of only 40 min., The authors are grateful to the Generalitat Valenciana for the fund-ing support for the Santiago Grisolia program (GRISOLIAP/2018/168) and to the Ministry of Science, Innovation and Universities (Spain) through the projects RTI2018-099033-B-C32 and C33 (MCIU/AEI/FEDER, UE) and RYC-2016-20915.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of SiC addition on mechanical behavior of thermal barriers with the aid of acoustic emission

  • Busquets Mataix, David Jeronimo|||0000-0001-5031-7805
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Bloem, Carlos
[EN] The improvement of high temperature materials with lower heat transfer coefficients lead to the development of thermal barrier coatings (TBCs). One of the most widely used materials for thermal barrier coatings is Y2O3 stabilized ZrO2 (Y-TZP) because of its excellent shock resistance, low thermal conductivity, and relatively high coefficient of thermal expansion. The aim of this work is to study the TBCs mechanical behavior with the addition of SiC into the suspension of Y-TZP/Al2O3 by acoustic emission (AE). Additionally, a microstructural analysis and a finite elements model were carried out in order to compare results. The coatings were made by suspension plasma spray (SPS) on metal plates of 70 x 12 x 2 mm(3). An intermetallic was deposited as a bond coating, followed by a coating of Y-TZP/Al2O3 with and without 15 wt.% SiC, with thicknesses between 87 and 161 mu m. The AE becomes a fundamental tool in the study of the mechanical behavior of thermal barriers. The use of wavelet transforms streamlines the study and analysis of recorded sound spectra. The crack generation arises at very low stress levels., The authors wish to thank the financial contribution of the Ministry of Economy, Industry, and Competitiveness of the Government of Spain, (MINECO), and to the RTI 2018-099033-B-C32-RETOS. A. Borrel acknowledges her contract (RyC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Null-thermal expansion coefficient LAS-nSiC composite by slip-casting

  • Suárez, M.
  • Díaz, L.A.
  • Bartolomé, J.F.
  • López-Esteban, S.
  • Torrecillas, R.
  • Moya, J.S.
  • Fernández, A.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] In the present work, lithium aluminosilicate (LAS) reinforced with SiC nanoparticles (nSiC) is successfully pre-pared by slip-casting for the first time. The stability of aqueous suspension is investigated in terms of its rheo-logical properties. The isoelectic point (IEP) of beta-Eucryptite particulate system was found to be at pH 6.1. To obtain the best processing conditions, LAS-nSiC suspension with 55 wt% of solids and 0.06 wt% of Tetramethyl ammonium hydroxide (TMAH) as dispersant is recommended. The slurry is slip-casted in plaster of Paris molds and sintered at 1430 degrees C for different holding times in controlled atmosphere. Microstructure, mechanical and coefficient of thermal expansion (CTE) properties of the sintered samples have been evaluated. LAS-nSiC com-posite sintered at 1430 degrees C shows dense and free-cracked microstructure with a CTE close to zero., This research was funded by the Spanish Ministry of Science and Innovation, Called Programa Estatal de I+D+i Orientada a los Retos de la Sociedad [RTI2018-102269-B-I00] . Likewise, the authors acknowledge the financial support of PID2020-119130GB-I00 project funded by MCIN/AEI/10.13039/501100011033. A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract [RYC-2016-20915] . Authors are grateful to Ainhoa Macias San Miguel from Nano-materials and Nanotechnology Research Center (CINN-CSIC-UNIOVI- PA) for providing technical assistance.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dry-sliding wear behavior of 3Y-TZP/Al2O3-NbC nanocomposites produced by conventional sintering and spark plasma sintering

  • Salem, Raphael
  • Gutiérrez-González, C.F.
  • Chinelatto, Adilson L.
  • Chinelatto, Adriana S.A.
  • Pallone, Eliria
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[EN] This work presents the initial results of the dry-sliding wear behavior of 3 mol% yttria-stabilized zirconia reinforced with 5 vol% alumina-niobium carbide (3Y-TZP/5 vol% Al2O3-NbC) nanocomposites sintered by conventional sintering and spark plasma sintering methods in the temperature range of 1350-1450 degrees C. The reinforcement of 3Y-TZP matrix with hard nanoparticles aimed to improve wear strength of the composites. Wear tests were performed by the ball-on-disc method using alumina (Al2O3) and tungsten carbide with 6 wt% cobalt cermet (WC-6%Co) balls as counter-materials, a load of 15 N, a sliding distance of 2000 m, and a sliding speed of 0.1 m/s. Wear behavior was evaluated in terms of wear rate and FE-SEM micrograph analysis of the wear tracks. The nanocomposite sintered at 1450 degrees C by conventional sintering exhibited the least wear when tested with the WC-6%Co ball. Generally, the wear mechanism showed evidence of severe wear regime with both counter-materials., The authors acknowledge the Brazilian institutions CAPES-PVE (grant number 23038.009604/2013-12), FAPESP (grant number 2015/07319-8), Fundação Araucária (grant number 810/2014), European Union/Erasmus Mundus for doctorate mobility (grant number EB15DM1542), and the Spanish Ministry of Economy and Competitiveness (RYC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Microwave-Assisted Synthesis and Sintering of Lead-Free KNL-NTS Ceramics

  • Lagunas-Chavarría, Anggel
  • Navarro-Rojero, María Guadalupe
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Catalá Civera, José Manuel|||0000-0002-0617-1762
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Lead-free piezoelectric powders (K0.44Na0.52Li0.04)(Nb0.82Ta0.10Sb0.04)O-3 were obtained by conventional and microwave-assisted reactive heating. Firstly, the synthesis of the material was carried out following the mixed oxide route and employing both traditional methods and microwave technology. Thermogravimetry, X-ray diffraction, field emission scanning electron microscopy and electrical properties analyses were evaluated. X-ray diffraction of the powders calcined by the microwave process shows the formation of perovskite structure with orthorhombic geometry, but it is possible to observe the presence of other phases. The presence of the secondary phases found can have a great influence on the heating rate during the synthesis on which the kinetics of the reaction of formation of the piezoelectric compound depend. The calcined powder was sintered at different temperatures by conventional and non-conventional processes. The microstructure of the ceramics sintered by microwave at 1050 degrees C for 10 min shows perovskite cubes with regular geometry, of size close to 2-5 p.m. However, the observed porosity (similar to 8%), the presence of liquid phase and secondary phases in the microstructure of the microwave sintered materials lead to a decrease of the piezoelectric constant. The highest d 33 value of 146 pC/N was obtained for samples obtained by conventional at 1100 degrees C 2 h compared to samples sintered by microwave at 1050 degrees C 10 min (similar to 15 pC/N)., This research was funded by the projects of the Spanish Ministry of Science and Innovation: RTI2018-099033-B-C32 and RYC-2016-20915, and Generalitat Valenciana (BEST/2021/084, BEST/2021/082).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructure and mechanical properties of 5.8 GHz microwave-sintered ZrO2/Al2O3 ceramics

  • Gil-Flores, Lorena
  • Fernández, Adolfo
  • Suárez-Menéndez, Marta
  • Rosa, Roberto
  • Veronesi, Paolo
  • Leonelli, Cristina
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Aim of the present study is to sinter zirconia nanocomposite powders doped with ceria and toughened with alumina (10Ce-TZP/Al2O3) by non-conventional means, i.e. microwave sintering technology. The sintering effects of various microwave applicators and frequency generators were evaluated using an optimised experimental set-up. The microwave-sintered samples were compared with the composites sintered by the conventional method. The mechanical properties of the ceramic composites were evaluated by their hardness, fracture toughness and Young's modulus. Likewise, their density and microstructure were analysed., The authors thank the Generalitat Valenciana for the financial support provided to the PROMETEU/2016/040 project. A. Borrell is grateful to the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Synthesis and sintering at low temperature of a new nanostructured beta- Eucryptite dense compact by spark plasma sintering

  • Suárez, M.
  • Fernández, A.
  • Díaz, L.A.
  • Sobrados, I.
  • Sanz, J.
  • Palomares, F.J.
  • Torrecillas, R.
  • Moya, J.S.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] The solid state reaction between kaolin and Li2CO3 with a 1:1 M composition has been studied in the temperature range 380 degrees C-550 degrees C. The role played by Li2CO3 (basic medium) in the thermal transformation of the kaolin has been investigated by X-Ray diffraction, FESEM, TEM, MAS-NMR and XPS techniques. For the first time, a nanostructured high density beta-Eucryptite ( < 10 nm) has been obtained by Spark Plasma Sintering (SPS) at 550 degrees C in high vacuum. The atmosphere used in sintering treatments has a determinant role in lithium migration and crystallization of beta-Eucryptite. In the case of low vacuum treatments, an amorphous LiAlSiO4 geopolymer type material was obtained. Due to exclusive properties and performances of beta-Eucryptite based materials, the results reported in the present investigation open new perspectives for new nanostructured and amorphous functional materials with null thermal expansion, ionic conduction and remarkable mechanical properties., The authors acknowledge the Principado de Asturias (Spain) for funding through the projects GRUPIN IDI/2018/000232 and MAT201678362-C4-2. A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-209.15).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of microwave heating effect in the behaviour of graphene as second phase in ceramic composites

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Centeno, Alba
  • Alonso, Beatriz
  • Zurutuza, Amaya
[EN] The choice of the right material is essential in microwave processing. The carbon materials are good microwave absorbers, which allows them to be transformed by microwave heating into new carbon materials with adapted properties, capable of heating other materials indirectly. In this paper, the microwave heating of graphene as reinforcement of the lithium aluminosilicate (LAS) ceramics has been explored. LAS ceramics have a near-zero coefficient of thermal expansion and exhibit an effective and efficient heating by microwave. Nevertheless, we have found that the graphene did not show any significant response to the microwave radiation and, hence, the interaction as mechanical reinforcement with the LAS material is harmful. The possible benefits of graphene materials to microwave technology are widely known; however, the mechanism involved in the interaction of microwave radiation with ceramic-graphene composites with high dielectric loss factors has not been addressed earlier., This research was funded by the project of the Spanish Ministry of Economy and Competitiveness (MINECO): RTI2018-099033-B-C32. A. Borrell acknowledges to MINECO her RyC contract (RYC-2016-20915)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructure and mechanical properties of 5.8 GHz microwave-sintered ZrO2/Al2O3 ceramics

  • Gil-Flores, Lorena
  • Salvador, M. D.
  • Peñaranda Foix, Felipe Laureano
  • Fernández, Adolfo
  • Suárez, Marta
  • Rosa, Roberto
  • Veronesi, Paolo
  • Leonelli, Cristina
  • Borrell, Amparo
Aim of the present study is to sinter zirconia nanocomposite powders doped with ceria and toughened with alumina (10Ce-TZP/Al2O3) by non-conventional means, i.e. microwave sintering technology. The sintering effects of various microwave applicators and frequency generators were evaluated using an optimised experimental set-up. The microwave-sintered samples were compared with the composites sintered by the conventional method. The mechanical properties of the ceramic composites were evaluated by their hardness, fracture toughness and Young's modulus. Likewise, their density and microstructure were analysed., The authors thank the Generalitat Valenciana for the financial support provided to the PROMETEU/2016/040 project. A. Borrell is grateful to the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tribological and wear behaviour of alumina toughened zirconia nanocomposites obtained by pressureless rapid microwave sintering

  • Gil-Flores, Lorena
  • Salvador, M. D.
  • Peñaranda Foix, Felipe Laureano
  • Dalmau, Alba
  • Fernández, Adolfo
  • Borrell, Amparo
Dense alumina toughened zirconia nanocomposites (ATZ, 3Y-TZP with 20 wt% Al2O3) were densified by non-conventional microwave sintering technology at relatively low temperatures (1200 and 1300 °C). The sintering method and its effect on densification, microstructure, mechanical properties and tribological behaviour were investigated. The outcomes demonstrated that the density rose as the sintering temperature was higher, and therefore the mechanical properties were enhanced, reaching a maximum hardness (18.4 ± 0.4 GPa) and fracture toughness (5.7 ± 0.3MPa· m1/2). In addition, the samples were subjected to a tribological test in dry and wet conditions, using artificial saliva. In both cases, the coefficient of friction and wear volume for samples obtained by microwave sintering are lower than conventional samples, with the wear volume being two times higher in dry conditions than in wet conditions., The authors are grateful to the Government of Valencia for the funding received for the project PROMETEU/2016/040. A. Borrell thanks to the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915). A. Dalmau acknowledges to the Valencia Government for the financial support (APOSTD/2017/051)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Comparison in mechanical properties of zirconium titanate (ZrTiO4) synthetized by alternative routes and sintered by microwave (MW)

  • Guillén Pineda, René Miguel
  • Borrell Tomás, María Amparo
  • Salvador Moya, Mª Dolores
  • Peñaranda Foix, Felipe Laureano
  • Moreno, Rodrigo
[EN] At present, ZrTiO4 nanopowders are used as a dielectric in the electroceramic field, applications of catalysis, microwave telecommunications devices, pigments, composites, etc. One of the most interesting applications is the potential as structural material and similar applications that require a high thermal resistance. However, all the properties of zirconium titanate are still a subject of interest for the industrial field.12 There are several routes of synthesis of ZrTiO4; among them is the sol-gel method and lyophilization. These methods have been used to make powders or small pieces of zirconium titanate. However, structural applications require materials in large quantities, so it is necessary to identify the differences between the methods of synthesizing and allowing the preparation of powders suitable for the generation of green materials for subsequent sintering.3 To develop a new generation of nanomaterials with microstructural differences it is necessary to innovate in the sintering process. Years ago, the use of conventional oven for sintering material was the usual procedure. Nowadays, non-conventional methods as Microwave sintering (MW) are a bright way to produce high dense materials, using heating rates in reduce dwell times and lower consumption using 70%-80% less energy. 4 This reactive sintering technique achieves excellent mechanical properties, homogeneous microstructure employing lower sintering temperatures. All these energy and economic advantages generate a new vision for the future on ceramic materials and their industrial production. The main objective of this study is to make a comparison of the mechanical properties of the materials synthesized by sol-gel method and lyophilization and sintered by microwaves., The authors would like to thank to the Generalitat Valenciana for financial support received for Santiago Grisolía program scholarship (GRISOLIAP/2018/168). A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and sintering at low temperature of a new nanostructured beta-Eucryptite dense compact by spark plasma sintering

  • Suárez, Marta
  • Fernández, Adolfo
  • Díaz, Luis A.
  • Sobrados, Isabel
  • Sanz Lázaro, Jesús
  • Borrell, Amparo
  • Palomares, F. Javier
  • Torrecillas, Ramón
  • Moya, J. S.
The solid state reaction between kaolin and Li2CO3 with a 1:1 M composition has been studied in the temperature range 380°C-550 °C. The role played by Li2CO3 (basic medium) in the thermal transformation of the kaolin has been investigated by X-Ray diffraction, FESEM, TEM, MAS-NMR and XPS techniques. For the first time, a nanostructured high density β- Eucryptite (<10 nm) has been obtained by Spark Plasma Sintering (SPS) at 550 °C in high vacuum. The atmosphere used in sintering treatments has a determinant role in lithium migration and crystallization of β- Eucryptite. In the case of low vacuum treatments, an amorphous LiAlSiO4 geopolymer type material was obtained. Due to exclusive properties and performances of β- Eucryptite based materials, the results reported in the present investigation open new perspectives for new nanostructured and amorphous functional materials with null thermal expansion, ionic conduction and remarkable mechanical properties., The authors acknowledge the Principado de Asturias (Spain) for funding through the projects GRUPIN IDI/2018/000232 and MAT2016-78362-C4-2. A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-209.15)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Lead-free low-melting-point glass as bonding agent for TiO2 nanoparticles

  • López-Esteban, Sonia
  • Cabal, Belén
  • Borrell, Amparo
  • Bartolomé, Jose F.
  • Fernández, Adolfo
  • Faraldos, Marisol
  • Bahamonde, A.
  • Moya, J. S.
  • Pecharromán, Carlos
This work is a study of the properties of TiO2-anatase nanoparticles attached by a low-melting point inorganic glass (530°C). Unlike other low-melting glasses, this composition does not contain any toxic metal. Likewise, it shows an excellent wettability on ceramic nanoparticles. A small addition of 5 vol% of glass remarkably enhances the mechanical strength of the composites with respect to pure TiO2 calcined at the same temperature, becoming twice this value. Self-cleaning properties analyzed using the methylene blue 385 nm UV-A photodegradation test showed that, after different UV-light periods, the photo-efficiency of TiO2-anatase was not altered by the presence of this glass., This work was supported by CSIC under grant 201960E103 and by the Spanish Ministry of Science Innovation and Universities (MCIU/AEI/FEDER, UE) under award RTI2018-094958-B-I00. Dr. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of colored on the microwave sintering behavior of dental zirconia ceramics

  • Moratal, Sheila
  • Gil-Flores, Lorena
  • Salvador, M. D.
  • Suárez, Marta
  • Peñaranda Foix, Felipe Laureano
  • Borrell, Amparo
The aim of this work is to study the physical, chemical, and mechanical properties of 3 mol% Yttria-stabilized Tetragonal Zirconia Polycrystalline (3Y-TZP) materials doped with varying amounts of iron oxide (0, 400, 800, and 1000 ppm). We carried out full dense consolidation using two different sintering methods: fast-microwave technology at 1200°C and 1300°C, and conventional furnace at 1400°C. It was observed an improvement in density and hardness values, as well as great fracture toughness, and more intense color was achieved resulting in more natural color, similar to that of human teeth, using the microwave technique at 1300°C compared to the conventional method. However, the microwave-sintered specimens exhibited an increase in zirconia grains size and high color intensity along with iron oxide content when compared to conventional process, where the grain size does not vary with the coloring agent content. The results obtained in this work suggest that microwave technology can produce an increase in sintering activity due to the different dielectric properties of 3Y-TZP materials doped with Fe2O3. Another interesting confirmed result is that the addition of Fe2O3 presents a high resistance to low temperature hydrothermal degradation producing a delay in the aging process., A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract (RYC-2016-20915)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A novel study of the effect of temperature on the crystal structure of lithium aluminosilicate materials

  • Benavente, Rut
  • Salvador, M. D.
  • Fernández, Adolfo
  • Borrell, Amparo
Dense Li2O–Al2O3–SiO2 (LAS) material was obtained in solid state by two sintering methods: conventional and microwave. The cyclical variation in temperature that these materials are subjected to during their useful life could cause changes in their crystalline structure and therefore changing their macroscopic properties. The role played by temperature in the diffraction patterns evolution was investigated through X-Ray thermodiffractometry measurements. Evolution of lattice parameters and crystal structure was determined and correlated with changes in the coefficient of thermal expansion. This work provides a comprehensive view of the thermal history of LAS materials according to the sintering technique used., This research was funded by the project of the Spanish Ministry of Economy and Competitiveness (MINECO): RTI2018-099033-B-C32 and RYC-2016-20915., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and processing of improved graphite-molybdenum-titanium composites by colloidal route and spark plasma sintering

  • Suárez, Marta
  • Fernández-González, Daniel
  • Díaz, Luis A.
  • Borrell, Amparo
  • Moya, J. S.
  • Fernández, Adolfo
Graphite-molybdenum-titanium composites might attract significant interest as heat sinks for different sector applications due to their excellent thermal, electrical and mechanical properties. This type of composites was already studied but following the powder metallurgy and spark plasma sintering (SPS) route. The aim of the present investigation is to study a new route of fabrication of these composites to improve their properties: colloidal synthesis and SPS process. The results obtained for graphite-10 vol% Mo-1 vol% Ti composites prepared by both routes are compared. It has been proved that the properties of the composites are significantly improved by the colloidal route compared with the powder metallurgy route, i. e. electrical conductivity by a factor of 3, thermal properties by a factor of 8 and bending strength by a factor of 4., This research was funded by the Spanish Ministry of Science and Innovation. Call Programa Estatal de I+D+i Orientada a los Retos de la Sociedad [RTI2018-102269-B-I00]. This research was also supported by a Juan de la Cierva Formación grant from the Spanish Ministry of Science and Innovation (MCINN) to Daniel Fernández-González [FJC2019-041139-I]. A. Borrell acknowledges for her RYC-2016-20915., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Null-thermal expansion coefficient LAS-nSiC composite by slip-casting

  • Suárez, Marta
  • Díaz, Luis A.
  • Bartolomé, Jose F.
  • Borrell, Amparo
  • López-Esteban, Sonia
  • Torrecillas, Ramón
  • Moya, J. S.
  • Fernández, Adolfo
In the present work, lithium aluminosilicate (LAS) reinforced with SiC nanoparticles (nSiC) is successfully prepared by slip-casting for the first time. The stability of aqueous suspension is investigated in terms of its rheological properties. The isoelectic point (IEP) of β-Eucryptite particulate system was found to be at pH 6.1. To obtain the best processing conditions, LAS-nSiC suspension with 55 wt% of solids and 0.06 wt% of Tetramethyl ammonium hydroxide (TMAH) as dispersant is recommended. The slurry is slip-casted in plaster of Paris molds and sintered at 1430ºC for different holding times in controlled atmosphere. Microstructure, mechanical and coefficient of thermal expansion (CTE) properties of the sintered samples have been evaluated. LAS-nSiC composite sintered at 1430ºC shows dense and free-cracked microstructure with a CTE close to zero., This research was funded by the Spanish Ministry of Science and Innovation, Called Programa Estatal de I+D+i Orientada a los Retos de la Sociedad [RTI2018–102269-B-I00]. Likewise, the authors acknowledge the financial support of PID2020–119130GB-I00 project funded by MCIN/AEI /10.13039/501100011033. A. Borrell acknowledges the Spanish Ministry of Economy and Competitiveness for her RyC contract [RYC-2016–20915]., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Mo content on the properties of graphite-MoC composites sintered by spark plasma sintering

  • Suárez, Marta
  • Fernández-González, Daniel
  • Díaz, Luis A.
  • Piñuela-Noval, Juan
  • Borrell, Amparo
  • Moya, J. S.
  • Torrecillas, Ramón
  • Fernández, Adolfo
In Press., [EN] Graphite–molybdenum–titanium powders prepared by colloidal processing technique were sintered by Spark Plasma Sintering (SPS). This material is proposed in this manuscript due to its potential interest as heat sink. The influence of the molybdenum content (2.5, 5.0 and 10.0 vol.%) on the thermal, electrical, and mechanical properties of the composite are studied to define the composite with the best properties. Thermal, electrical, and mechanical properties of the composite graphite–10 vol.% Mo–1 vol.% Ti (that are composites of graphite with molybdenum and titanium carbides after sintering) are significantly better than those of the composites with lower molybdenum contents (2.5 vol.% and 5 vol.%). This way, flexural strength, electrical conductivity, and thermal conductivity are 1.5, 7.8 and 18 times greater, respectively, than in the composite graphite–2.5 vol.% Mo–1 vol.% Ti. In the case of comparing with the composite graphite–5 vol.% Mo–1 vol.% Ti, flexural strength, electrical conductivity, and thermal conductivity are 1.2, 5.1 and 3.2 greater in the composite graphite–10 vol.% Mo–1 vol.% Ti, respectively., [ES] Se sinterizaron por Spark Plasma Sintering (SPA) polvos de grafito-molibdeno-titanio preparados mediante la técnica de síntesis coloidal. En el presente manuscrito se propone este material debido a su potencial en disipadores de calor. Se estudió la influencia del contenido en molibdeno (2,5, 5,0 y 10,0 vol.%) en las propiedades térmicas, eléctricas y mecánicas del material compuesto para definir aquel con las mejores propiedades. De este modo, las propiedades térmicas, eléctricas y mecánicas del material compuesto grafito-10 vol.% Mo-1 vol.% Ti (que son composites de grafito con carburos de titanio y molibdeno tras la sinterización) son significativamente mejores que aquellas de los materiales compuestos con menores contenidos en molibdeno (2,5 vol.% y 5 vol.%). Así pues, la resistencia a flexión, la conductividad eléctrica y la conductividad térmica son 1,5, 7,8 y 18 veces superiores, respectivamente, a las del composite grafito-2,5 vol. Mo-1 vol.% Ti. Si la comparación se lleva a cabo con el material compuesto grafito-5 vol.% Mo-1 vol.% Ti, la resistencia a flexión, la conductividad eléctrica y la conductividad térmica son 1,2, 5,1 y 3,2 veces superiores en el material compuesto grafito-10 vol. Mo-1 vol.% Ti, respectivamente., This research was funded by the Spanish Ministry of Science and Innovation. Call Programa Estatal de I+D+i Orientada a los Retos de la Sociedad (RTI2018-102269-BI00). Daniel Fernández-González acknowledges the grant (Juan de la Cierva-Formación program) FJC2019-041139-I funded by MCIN/AEI/ 10.13039/501100011033 (Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación). Amparo Borrell acknowledges for her RYC-2016-20915. Juan Piñuela Noval acknowledges the Programa “Severo Ochoa” of Grants for Research and Teaching of the Principality of Asturias for the funds received for the elaboration of the Ph.D. Thesis (Ref: BP20 041)., Peer reviewed