Pasar al contenido principal

ANTENAS RECONFIGURABLES PARA COMUNICACIONES DE BANDA ANCHA EN LA BANDA DE MILIMETRICAS

PID2019-107688RB-C22

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

A Half-Mode Groove Gap Waveguide for Single-Layer Antennas in the Millimeter-Wave Band

  • Ferrando-Rocher, Miguel
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Baquero-Escudero, Mariano
This paper presents an alternative to significantly reduce the time and difficulty in designing and fabricating antennas in Gap Waveguide technology (GW) by using a novel half-mode groove gap waveguide. GW is often criticized within the subtractive manufacturing field for the high fabrication time required to mill many pins with the waveguides in the same piece. To demonstrate the possibilities of this new approach, two different antennas have been designed, fabricated, and measured. Both antennas, formed by only two pieces with no contact, operate from 29 GHz to 31 GHz and present reflection coefficients below −10 dB and high antenna efficiency above 90%. In addition, both prototypes can reuse the bed of nails, which favors shorter manufacturing times and lower costs in the development phase.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

A Ka-band Compact Single-Layer Gap Waveguide Monopulse Slot Array Antenna

  • Ferrando-Rocher, Miguel
  • Mayor, Bryan
  • Marini, Stephan
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
This paper presents a gap-waveguide-based compact monopulse array antenna for millimeter-wave tracking applications at Ka-band (27.5 to 30.5 GHz). A low-loss Magic-Tee is designed to be used in a monopulse comparator network. The gap waveguide planar monopulse comparator network is integrated in a single layer with a 2 x 2 corporate-fed network combining ridge gap and groove gap waveguides. Simulated results show bandwidths of 10% with input reflection coefficients better than -12 dB for the sum and difference ports over the frequency band of interest. Besides, the isolation between sum and difference ports is more than 50 dB. The simplicity of the design and the fact that it is housed in a single layer permit easy scaling to larger arrays.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Single-Layer Sequential Rotation Network in Gap Waveguide for a Wideband Low-Profile Circularly Polarized Array Antenna

  • Ferrando-Rocher, Miguel
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Bernardo-Clemente, Bernardo
A low-profile circularly-polarized sequential rotation fed 4x4 array antenna working in the Ka-band from 27.5 GHz to 31 GHz is presented. The particularity of the antenna lies in its single-layer sequential rotation feed network implemented in a bed of nails using a combination of groove and ridge gap waveguides. The basic radiating element is one slot loaded by a simple coffee-bean-shaped parasitic element on top. Experimental results show an antenna matching below −10 dB in a 13.6% bandwidth and a measured axial ratio below 1.3 dB in the desired band.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Selective Laser Sintering Manufacturing as a Low Cost Alternative for Flat-Panel Antennas in Millimeter-Wave Bands

  • Ferrando-Rocher, Miguel
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Bernardo-Clemente, Bernardo
In this paper, the capabilities of Selective Laser Sintering metal 3D-Printing technology to achieve a lightweight and cost-effective flat panel antenna in the millimeter wave band are studied. Specifically, two identical dual-band 4×4 array antennas working in the K and Ka bands have been manufactured; one with Selective Laser Sintering (SLS) and one using computer numerical control (CNC). Measured performance of the SLS antenna prototype is benchmarked with the performance of the previously measured CNC antenna. Experimental results reveal the strengths and weaknesses of this particular low-cost additive manufacturing technique with respect to traditional subtractive manufacturing techniques.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Dual-Band Single-Layer Slot Array Antenna Fed by K/Ka-Band Dual-Mode Resonators in Gap Waveguide Technology

  • Ferrando-Rocher, Miguel
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Baquero-Escudero, Mariano
This paper presents a 4 x 4 single-layer dual-band array antenna operating in K and Ka-band using Gap Waveguide technology (GW). Radiating elements consist of I-shaped slots located on the top plate of the antenna and cavity backed by a novel coaxial cavity with dual-frequency operation. The antenna presents two ports, one for each band, which radiate a directive far field pattern with linear polarization. A single-layer high-bandwidth corporate-feed network is used to excite the cavities. In addition, a diplexer is integrated as part of the network to separate both working bands. Experimental results show impedance and radiation pattern bandwidths larger than 2 GHz in both bands.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Wideband Coffee-Bean Shaped Radiating Element for Circularly-Polarized Waveguide Slot Arrays

  • Ferrando-Rocher, Miguel
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
A wideband coffee-bean shaped radiating element for circularly-polarized waveguide slot arrays is presented. The proposed solution is based on a very simple polarizer aimed to be integrated into flat panel antennas in the millimeter-wave band. For validation purposes, a slot array fed by a groove gap waveguide network at 30 GHz is taken as a feeder. Simulated results using periodic boundary conditions in a 2×2 unit cell are presented in this work. Preliminary results show a frequency bandwidth of 4 GHz with input reflection coefficient better than −-10 dB. It is worth stressing the good polarization purity achieved, being below 1.5 dB from 29 GHz to 31 GHz and below 3 dB in the whole band of interest (28 to 32 GHz).
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

1x4 Antenna Array corporately fed by a Novel Half-Mode Groove Gap Waveguide network

  • Ferrando-Rocher, Miguel
This paper presents a Ka-band linearly-polarized 4-antenna array fed with a novel corporate distribution network that uses a half-mode groove gap waveguide (HM-GGW). The antenna feed has no contact with the top cover where the array antenna is located, thanks to the features inherent in gap waveguide technology (GW). This technology, with many advantages, sometimes suffers from a complex mechanization, which in this case is reversed by the novel network proposed in this paper.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Novel Asymmetric T-Shaped Radiating Element for Circularly-Polarized Waveguide Slot Arrays

  • Herranz-Herruzo, Jose Ignacio
  • Ferrando-Rocher, Miguel
  • Valero-Nogueira, Alejandro
  • Bernardo-Clemente, Bernardo
Waveguide slot arrays are a widely used solution to attain linearly-polarized high-gain antennas. In this paper, an all-metal T-shaped radiating element is conceived with the aim to replace the usual rectangular slots and attain circularly-polarized arrays, preserving their good properties. The polarization conversion is made possible thanks to the inclusion of a parasitic arm perpendicular to the main active slot. Due to the fact that this second arm is not directly fed by the waveguide but coupled to the active slot, the T-shaped element can be used in any array originally formed by metallic rectangular slots. The design of resonant shunt arrays has been addressed here for validation purposes. The experimental results of two sample linear arrays at 30 GHz demonstrate the design accuracy and manufacturing reliability, reporting an axial ratio below 2 dB within a bandwidth of 1.9 GHz and a peak efficiency around 98%.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

A Gap Waveguide-Based 2x2 Circularly-polarized Monopulse Antenna Array

  • Vazquez-Sogorb, Carlos
  • Ferrando-Rocher, Miguel
  • Marini, Stephan
  • Herranz-Herruzo, Jose Ignacio
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
This paper presents a circular-polarized gap-waveguide-based compact monopulse array antenna for millimeter-wave tracking applications at Ka-band (29 to 31 GHz). The gap waveguide planar monopulse comparator network is integrated in a single layer with a 2×2 corporate-fed network combining ridge gap and groove gap waveguides. Radiating cavities consist of cubes with chamfered corners. Preliminary results show a bandwidth of 2 GHz with input reflection coefficients better than −20 dB for both ports of the antenna. In addition, the isolation between ports is greater than 50 dB. The design allows for scalability to build higher gain arrays from the antenna presented in this communication.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Half-Mode Waveguide Based on Gap Waveguide Technology for Rapid Prototyping

  • Ferrando-Rocher, Miguel
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Baquero-Escudero, Mariano
In this letter, a half-mode waveguide based on gap waveguide (GW) technology for rapid prototyping is explored. Two devices have been designed and measured for demonstration purposes: a power divider and a curved waveguide. Both devices are constructed from two noncontacting metal pieces. Both devices also follow the same design process. In the bottom piece, a horizontally polarized groove GW (GGW) is housed. The height of the groove is about half, which is required to propagate the fundamental mode. The top cover is a uniform pinned surface that acts as a high impedance surface (HIS) over the groove below. Both the power divider and the curved waveguide show measured reflection coefficient values of less than -15 dB in the bandwidth of interest (28-31 GHz) and are in excellent agreement with simulated results. These devices stand out for their ease of fabrication and open a horizon for cheaper and more robust GW designs for mass production.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Elemento radiante de banda ancha en forma de grano de café para guías de onda ranuradas con polarización circular

  • Ferrando-Rocher, Miguel
Se presenta un elemento radiante de banda ancha con forma de grano de café para agrupaciones de guía de ondas ranuradas con polarización circular. La solución propuesta se basa en un polarizador muy sencillo destinado a ser integrado en antenas planas en la banda de ondas milimétricas. Para su validación, se toma como alimentador una agrupación de ranuras conectadas por una red corporativa. En este trabajo se presentan resultados simulados utilizando condiciones de contorno periódicas en la celda unidad. Los resultados preliminares muestran un ancho de banda de frecuencia de 4 GHz con un coeficiente de reflexión por debajo de -10 dB. Cabe destacar la buena pureza de polarización conseguida, al obtener una relación axial por debajo de 1.5 dB de 29 GHz a 31 GHz y por debajo de 3 dB en toda la banda de interés (28 a 32 GHz).
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Agrupación de ranuras alimentadas por una novedosa guía semi-modo en Gap Waveguide

  • Ferrando-Rocher, Miguel
  • Pérez-Guimerá, Alejandro
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Marini, Stephan
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
This paper presents a novel antenna feed network that significantly facilitates the design and fabrication in Gap Waveguide technology. In particular, a 1x4 linearly polarized Ka-band antenna array with a novel corporate distribution network using a half-mode groove-gap waveguide (HM-GGW). The good simulated results obtained from 29 GHz to 31 GHz by this breadboard give the first validity to this new development for GW.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Guía semi-modo en tecnología Gap Waveguide para prototipado rápido de dispositivos

  • Ferrando-Rocher, Miguel
  • Valero-Nogueira, Alejandro
  • Herranz-Herruzo, Jose Ignacio
  • Bernardo-Clemente, Bernardo
In this communication, a half-mode waveguide based on Gap Waveguide technology for rapid prototyping is presented. A power divider is designed for demostration purposes. The power divider is constructed from two non-contacting metal pieces. The horizontally-polarized power divider is housed in the bottom piece. The height of the groove is about half that which would be required to propagate the fundamental mode. The top cover is a uniform pinned surface that acts as a High Impedance Surface (HIS) over the groove of the bottom plate. The simulated reflection coefficient shows values of less than −15 dB in the bandwidth of interest (28 to 31 GHz). This design stands out for its ease of fabrication and opens a horizon for cheaper and more robust GW designs for mass production.