Pasar al contenido principal

MODELADO AVANZADO Y CARACTERIZACION DE NUEVOS COMPONENTES DE ALTA FRECUENCIA EN GUIA DE ONDA Y TECNOLOGIA PLANAR PARA LAS APLICACIONES ESPACIALES EMERGENTES

PID2019-103982RB-C43

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ALICANTE

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Increasing Peak Power Handling in Microstrip Bandpass Filters by Using Rounded-End Resonators

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Á.
  • Marini, Stephan
  • Guglielmi, Marco
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This work describes a new strategy for improving the peak power handling capability (PPHC) of microstrip bandpass filters (BPFs) without any degradation in the electrical performance. For this purpose, a new resonator topology with rounded open-circuit terminations is proposed. Using this strategy, sharp edges are avoided, and a reduction of the maximum peak voltage (V-peak) is obtained, leading to higher peak power thresholds. An in-depth analysis of the variation of V-peak and PPHC as a function of the circle radius is also carried out. As a validation, two microstrip BPFs centered at 1.6 GHz with different end-circle sizes are designed, manufactured, and measured, showing a PPHC enhancement of 2.10 and 1.15 dB, respectively, compared to a standard microstrip BPF., This work was supported in part by the University of Alicante through the Fellowship Grant UAFPU2018-054 and in part by the Ministry of Science and Innovation through the sub-projects C41 and C43 of the Coordinated Project PID2019-103982RB.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

A Ka-band Compact Single-Layer Gap Waveguide Monopulse Slot Array Antenna

  • Ferrando-Rocher, Miguel|||0000-0003-4098-7180
  • Valero-Nogueira, Alejandro|||0000-0001-9296-4162
  • Herranz Herruzo, José Ignacio|||0000-0002-0507-1487
  • Mayor, Bryan
  • Marini, Stephan
[EN] This paper presents a gap-waveguide-based compact monopulse array antenna for millimeter-wave tracking applications at Ka-band (27.5 to 30.5 GHz). A low-loss Magic-Tee is designed to be used in a monopulse comparator network. The gap waveguide planar monopulse comparator network is integrated in a single layer with a 2×2 corporate-fed network combining ridge gap and groove gap waveguides. Simulated results show bandwidths of 10% with input reflection coefficients better than ¿12 dB for the sum and difference ports over the frequency band of interest. Besides, the isolation between sum and difference ports is more than 50 dB. The simplicity of the design and the fact that it is housed in a single layer permit easy scaling to larger arrays., This work has been funded by the Spanish Ministry of Science and Innovation under projects PID2019-107688RBC22 and PID2019-103982RB-C43.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bandpass Filter in Ridge Empty Substrate Integrated Waveguide With U-Shaped Impedance Inverters

  • David Herraiz|||0000-0002-3793-6078
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Morro, J. V.|||0000-0002-4699-6208
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Herraiz, Darío
  • Belenguer, Angel
[EN] Substrate integrated waveguides (SIWs) are a com- promise in terms of performance, cost, and volume between classical planar technologies and high quality three-dimensional waveguides. Empty SIWs (ESIW) reduce the losses by removing the dielectric substrate. In order to increase the usable bandwidth of the ESIW, a ridge layer can be added to the ESIW, thus obtaining the so-called ridge ESIW (RESIW). A transition from microstrip to RESIW has already been presented, but no other passive component has yet been implemented in this new technol- ogy. In this letter, we present a novel bandpass filter in RESIW, based on a new U-shaped geometry acting as impedance inverter, that can be easily fabricated with planar circuit manufacturing techniques. A design procedure for this filter is presented. A four-pole Chebyshev filter centered at 15 GHz, with a relative bandwidth of 3%, has been manufactured. The measured values for insertion and return losses are, respectively, lower than 1.05 dB and greater than 18 dB in the whole passband., This work was supported by the Ministerio de Ciencia e Innovacion (MICIN, Spanish Government) under Research Project PID-2019-103982RB-C41 and Project PID-2019-103982RB-C43 (funded by MICIN/AEI/10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Estrategia de Diseño para Aumentar la Capacidad en Potencia en Guias de Onda Groove-Gap

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Ángel
  • Marini, Stephan
  • Ferrando-Rocher, Miguel|||0000-0003-4098-7180
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This work describes a new design strategy for improving the power handling capability (PHC) of groove gap waveguides (GGW). First, a theoretical analysis is carried out to study the distribution of the quasi-TE10 mode and the variation of the PHC for different configurations and frequencies. Then, in order to minimize the strength of the maximum electric field above the pins, three of the main geometrical dimensions of the nails are optimized. Finally, the numerical results show that by using this strategy, the corona discharge power thresholds can be enhanced without degrading the electrical response., Este trabajo ha sido financiado por la Universidad de Alicante mediante la beca de investigación UAFPU2018-054, y por el Ministerio de Ciencia e Innovación a través de los proyectos de investigación PID2019-103982RB-C41 y PID2019-103982RB-C43.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A New Family of Reconfigurable Waveguide Filters and Diplexers for High-Power Applications

  • Melgarejo, Juan Carlos
  • Ossorio, Javier
  • Guglielmi, Marco
  • San-Blas, Angel Antonio
  • Tronser, Tillman
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Valencia-Sullca, Joaquín Francisco
  • Vidal Pantaleoni, Ana|||0000-0002-3853-6260
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this paper, we discuss how the use of the recently developed modified tuning pin (MTP) can be extended to the design of filters and diplexers implemented in rectangular waveguide, that can be reconfigured in a number of discrete states, and that can be used in high-power payloads. As an application example, the design of two reconfigurable filters and a reconfigurable diplexer is fully described. The highpower behavior of these components (in particular, with respect to corona and multipaction effects) is also studied in detail, in order to demonstrate that the structures that we discuss can operate correctly under highpower conditions. Furthermore, comparisons between simulations and measurements of several prototypes are also included, showing an excellent agreement between simulated and experimental data, thereby fully validating both the design approach and the filter reconfiguration strategy., This work was supported by the Ministerio de Ciencia e Innovacion, Spanish Government, through the Subprojects C43 and C41 of theCoordinated Research and Development Project PID2019-103982RB under Grant MCIN/AEI/10.13039/501100011033
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancement of corona discharge thresholds in microstrip bandpass filters by using cover-ended resonators

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Á.
  • Marini, Stephan
  • Esteve, Laura
  • Guglielmi, Marco
  • Reglero Mangada, Marta Sofía|||0000-0002-3811-843X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This paper studies the corona discharge power thresholds in microstrip bandpass filters (BPFs) and, in particular, is focused on a solution based on lambda/2 cover-ended resonators to enhance their peak power handling capability (PPHC). First, a parametric analysis is carried out to evaluate the variation of the maximum electric field and the unloaded quality factor (Q(u)) as a function of the cover's geometrical dimensions (i.e. height, length, and width). Next, several microstrip BPFs centered at 1.6 GHz are designed, and their behaviors under moderate-to-high applied RF power signals are simulated to corroborate the previous study. A suitable number and size of covers are selected to enhance PPHC without barely degrading the filters' electrical performance and, consequently, without hardly increasing the insertion losses. Finally, two third-order filters with covers and without covers (benchmark prototype) are manufactured, by way of illustration, and they are tested in the European High-Power RF Space Laboratory to validate the good performance of the proposed solution, where a PPHC enhancement of 3.1 dB at high pressures is achieved as compared to the benchmark prototype., This work has been supported by the University of Alicante through the fellowship grant UAFPU2018-054 and by the "Ministerio de Ciencia e Innovacion" through the sub-projects C41 and C43 of the coordinated project PID2019-103982RB. The authors would like to thank Val Space Consortium for its contribution - Laboratories funded by the European Development Fund - A way of making Europe.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Peak Power Handling Capability in Groove Gap Waveguide Filters Based on Horizontally Polarized Resonators and Enhancement Solutions

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Ángel
  • Marini, Stephan
  • Ferrando-Rocher, Miguel|||0000-0003-4098-7180
  • Taroncher Calduch, Mariam|||0000-0001-9068-1169
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This letter studies the peak power handling capability (PPHC) in groove gap waveguide filters based on horizontally polarized resonators. Moreover, a modification of the resonant cavity is proposed, where the central pins of the original structure are replaced by a rounded metal block. As a result of this change, the TE101-like mode can still be excited, but the maximum electric field strength is shifted to the center of the cavity, which leads to a higher PPHC. The main advantages of the original structure are maintained, and greater robustness in the manufacturing process is achieved. Next, some guidelines for the design of the coupling windows and the dimensions of the blocks are shown to minimize the electric field strength and, consequently, maximize the PPHC. Finally, two third-order bandpass filters (with pins and with blocks) centered at 16 GHz have been manufactured and tested in a measurement campaign, where a PPHC enhancement of 8.7 dB at high pressures is achieved for the novel solution presented in this work., This work was supported in part by the University of Alicante through the Fellowship Grant UAFPU2018-054 and in part by MCIN/AEI/10.13039/501100011033 through the Sub-Projects C41 and C43 of the Coordinated Project under Grant PID2019-103982RB.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Efficient Design Procedure for Combline Bandpass Filters With Advanced Electrical Responses

  • Jamshidi Zarmehri, Hojjat
  • San Blas Oltra, Ángel Antonio
  • Neshati, Mohammad
  • Sharma, Abhishek
  • Coves Soler, Ángela
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this paper, a very efficient procedure for designing waveguide combline bandpass filters with an advanced electrical response is presented. The proposed technique is based on a segmentation strategy, which reduces the number of variables to be optimized by dividing the design process into simpler stages. The electrical response of an appropriate equivalent circuit model of the waveguide structure considered in each stage is used to generate the target curve needed in the optimization process. Moreover, the well- known Aggressive Space Mapping technique has been also implemented to improve the computational efficiency of the whole method. In order to validate the proposed design procedure, two high-order combline bandpass filters, with symmetric and asymmetric electrical responses including transmission zeros, have been successfully designed and simulated with full-wave analysis tools. Furthermore, as an experimental validation, a prototype of the symmetric filter has been manufactured, showing a good agreement between simulated and experimental data., This work was supported by the Ministerio de Ciencia e Innovación, Spanish Government, through the Subprojects C43 and C41 of the Coordinated Research and Development Projects PID2019-103982RB and TED2021-129196B, under Grant MCIN/AEI/10.13039/501100011033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the Multipactor Effect in Groove Gap Waveguide Technology

  • Vague Cardona, José Joaquín|||0000-0001-5935-3116
  • Reglero Mangada, Marta Sofía|||0000-0002-3811-843X
  • Vidal Pantaleoni, Ana|||0000-0002-3853-6260
  • Baquero Escudero, Mariano|||0000-0001-8772-5431
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Asensio, Irene
  • Coves, Ángela
  • San Blas, Ángel A.
  • Raboso, David
[EN] This article presents a theoretical and experimental comparative study of the different multipactor threshold values obtained in the rectangular waveguide (RW) and the groove gap waveguide (GGW). To this end, the multipactor effect has been first analyzed in an RW with a recently developed theoretical model. Then, the multipactor breakdown power levels in the equivalent GGW have been predicted with an accurate electron tracking code, showing a significant increment compared with the RW case. In order to validate these results, two E-plane WR-90 RW transformers have been designed with a full-wave electromagnetic simulation tool. The central sections of these transformers have been implemented in RW and GGW, respectively, and their multipactor breakdown power levels have also been predicted. The two designed transformers have been fabricated in aluminum and then measured in terms of electrical response (scattering parameters) and RF multipactor effect (power threshold values). All the experimental results agree well with the set of simulated data, thus fully validating the performed study., This work was supported by the Ministerio de Ciencia e Innovacion, Spanish Government, through the Subprojects C41 and C43 of the Coordinated Research and Development Project PID2019103982RB under Grant MCIN/AEI/10.13039/501100011033.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Study and Proposal of High-Power Handling Capability Microwave Filtering Solutions

  • Morales-Hernández, Aitor
Over the last few years, the ever-increasing use of the new emerging wireless communication systems has imposed a considerable challenge in the development of novel microwave devices that can support the high bit rates and wide bandwidths demanded by the society. Moreover, other of the main goals of the current microwave components' designers is the fact that these devices can withstand the increasingly higher RF power requirements that must be considered at the output stages of transmitters. In this context, several physical phenomena should be analyzed in order to maximize the so-called power handling capability (PHC) in microwave components. In particular, this thesis focuses on the study of the corona discharge breakdown, since it is a physical effect that may limit the peak power thresholds (also known as peak power handling capability or PPHC) of microwave devices. In this regard, the main aim of this work is the proposal of several design strategies to achieve a considerable improvement of the PPHC in different filtering structures. In this sense, this dissertation is divided into two main parts. On the one hand, the study of the corona discharge breakdown will be first focused on microstrip bandpass filters, where the variation of the maximum electric field strength will be analyzed, and different solutions based on dielectric covers, rounded open-circuit terminations, an anticorona lacquer or a commercial adhesive will be thoroughly investigated and compared. The main objective will be the maximization of the peak power levels, while the degradation of the unloaded quality factor of the resonators will be minimized as far as possible. On the other hand, the second part of this thesis dissertation deals with a similar exhaustively analysis in groove gap waveguides (GGWs). Furthermore, different topologies of bandpass filters based on this technology will be studied, focusing also on the type of the electric field's polarization. In a similar way, several design criteria will be proposed for improving the PPHC of these components, thereby achieving a significant enhancement and reaching the same peak power thresholds of the counterpart rectangular waveguide devices. Finally, all the solutions described above will be experimentally validated in diverse measurement campaigns carried out at the European High Power RF Space Laboratory to corroborate the proper and good performances of all of them.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Design Strategy and Considerations to Improve Corona Discharge Breakdown in Groove Gap Waveguides

  • Morales-Hernández, Aitor
  • Ferrando-Rocher, Miguel
  • Sánchez-Soriano, Miguel Ángel
  • Marini, Stephan
  • Boria Esbert, Vicente Enrique
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
This paper studies the corona discharge breakdown thresholds in groove gap waveguides, and proposes a design strategy to enhance its peak power handling capability (PPHC). The theoretical analysis is focused on the study of the quasi-TE 10 mode, and on the PPHC at different frequencies and multiple arrangements of the pin dimensions of the bed of nails. Next, the geometrical parameters width, length and separation of such pins are optimized for improving peak power limits. Finally, the simulated results show reasonably good performance with respect to the equivalent rectangular waveguide power limit.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

A Ka-band Compact Single-Layer Gap Waveguide Monopulse Slot Array Antenna

  • Ferrando-Rocher, Miguel
  • Mayor, Bryan
  • Marini, Stephan
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
This paper presents a gap-waveguide-based compact monopulse array antenna for millimeter-wave tracking applications at Ka-band (27.5 to 30.5 GHz). A low-loss Magic-Tee is designed to be used in a monopulse comparator network. The gap waveguide planar monopulse comparator network is integrated in a single layer with a 2 x 2 corporate-fed network combining ridge gap and groove gap waveguides. Simulated results show bandwidths of 10% with input reflection coefficients better than -12 dB for the sum and difference ports over the frequency band of interest. Besides, the isolation between sum and difference ports is more than 50 dB. The simplicity of the design and the fact that it is housed in a single layer permit easy scaling to larger arrays.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Enhancement of corona discharge thresholds in microstrip bandpass filters by using cover-ended resonators

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Ángel
  • Marini, Stephan
  • Reglero, Marta
  • Esteve, Laura
  • Boria Esbert, Vicente Enrique
  • Guglielmi, Marco
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
This paper studies the corona discharge power thresholds in microstrip bandpass filters (BPFs) and, in particular, is focused on a solution based on λ/2 cover-ended resonators to enhance their peak power handling capability (PPHC). First, a parametric analysis is carried out to evaluate the variation of the maximum electric field and the unloaded quality factor (Qu) as a function of the cover’s geometrical dimensions (i.e. height, length, and width). Next, several microstrip BPFs centered at 1.6 GHz are designed, and their behaviors under moderate-to-high applied RF power signals are simulated to corroborate the previous study. A suitable number and size of covers are selected to enhance PPHC without barely degrading the filters’ electrical performance and, consequently, without hardly increasing the insertion losses. Finally, two third-order filters with covers and without covers (benchmark prototype) are manufactured, by way of illustration, and they are tested in the European High-Power RF Space Laboratory to validate the good performance of the proposed solution, where a PPHC enhancement of 3.1 dB at high pressures is achieved as compared to the benchmark prototype.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Peak Power Handling Capability in Groove Gap Waveguide Filters Based on Horizontally Polarized Resonators and Enhancement Solutions

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Ángel
  • Ferrando-Rocher, Miguel
  • Marini, Stephan
  • Taroncher Calduch, Máriam
  • Boria Esbert, Vicente Enrique
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
This letter studies the peak power handling capability (PPHC) in groove gap waveguide filters based on horizontally polarized resonators. Moreover, a modification of the resonant cavity is proposed, where the central pins of the original structure are replaced by a rounded metal block. As a result of this change, the TE₁₀₁-like mode can still be excited, but the maximum electric field strength is shifted to the center of the cavity, which leads to a higher PPHC. The main advantages of the original structure are maintained, and greater robustness in the manufacturing process is achieved. Next, some guidelines for the design of the coupling windows and the dimensions of the blocks are shown to minimize the electric field strength and, consequently, maximize the PPHC. Finally, two third-order bandpass filters (with pins and with blocks) centered at 16 GHz have been manufactured and tested in a measurement campaign, where a PPHC enhancement of 8.7 dB at high pressures is achieved for the novel solution presented in this work.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Multimode Equivalent Networks for Shielded Microwave Circuits With Thick Metallizations

  • Gómez Molina, Celia
  • Quesada Pereira, Fernando
  • Marini, Stephan
  • Álvarez Melcón, Alejandro
  • Boria Esbert, Vicente Enrique
  • Guglielmi, Marco
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
In this article, we show how the multimode equivalent network (MEN) technique can be extended to the analysis of multilayer boxed planar microwave circuits that are built using a thick metallization. This analysis is carried out considering the thick metallic circuit as a length of the uniform waveguide. The problem is then divided into two waveguide steps (or junctions). We first obtain the equivalent network of the two junctions. Then, we cascade them to obtain the MEN of the complete circuit, thereby including the effect of finite thickness rigorously. A key aspect of the formulation that we propose is that it includes ports in the transverse plane of the circuit. In addition to theory, several shielded microwave filters using a thick metallization are also analyzed. An in-depth study of the numerical convergence is also performed for two practical examples. Simulation results are shown to be in good agreement with both commercial simulation tools and measurements, thereby fully validating our theoretical formulation.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

1x4 Antenna Array corporately fed by a Novel Half-Mode Groove Gap Waveguide network

  • Ferrando-Rocher, Miguel
This paper presents a Ka-band linearly-polarized 4-antenna array fed with a novel corporate distribution network that uses a half-mode groove gap waveguide (HM-GGW). The antenna feed has no contact with the top cover where the array antenna is located, thanks to the features inherent in gap waveguide technology (GW). This technology, with many advantages, sometimes suffers from a complex mechanization, which in this case is reversed by the novel network proposed in this paper.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

A Gap Waveguide-Based 2x2 Circularly-polarized Monopulse Antenna Array

  • Vazquez-Sogorb, Carlos
  • Ferrando-Rocher, Miguel
  • Marini, Stephan
  • Herranz-Herruzo, Jose Ignacio
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
This paper presents a circular-polarized gap-waveguide-based compact monopulse array antenna for millimeter-wave tracking applications at Ka-band (29 to 31 GHz). The gap waveguide planar monopulse comparator network is integrated in a single layer with a 2×2 corporate-fed network combining ridge gap and groove gap waveguides. Radiating cavities consist of cubes with chamfered corners. Preliminary results show a bandwidth of 2 GHz with input reflection coefficients better than −20 dB for both ports of the antenna. In addition, the isolation between ports is greater than 50 dB. The design allows for scalability to build higher gain arrays from the antenna presented in this communication.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

In-depth Study of the Corona Discharge Breakdown Thresholds in Groove Gap Waveguides and Enhancement Strategies for Inductive Bandpass Filters

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Ángel
  • Ferrando-Rocher, Miguel
  • Marini, Stephan
  • Boria Esbert, Vicente Enrique
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
This work focuses on the study of the corona discharge breakdown in groove gap waveguides (GGWs) and inductive bandpass filters (BPFs) based on this technology. With the main aim of improving the peak power handling capability (PPHC), the location of the maximum normalized electric field strength (|Ê MAX |) as a function of the geometrical parameters is analyzed. First, the research deals with wave-guiding structures, comparing the distribution of the transverse electric TE10-like mode of a GGW to that of an equivalent rectangular waveguide (RW). Next, a design strategy based on the adjustment of the geometrical dimensions of the bed of nails is proposed, thus achieving a considerable reduction of |Ê MAX |. The second part of this paper aims for vertically polarized GGW BPFs, where the inductive irises become the most critical part of the component. By a simple modification of their dimensions, a second design criterion is suggested for improving the PPHC. Finally, several Ku-band BPFs centered at 14 GHz and 16 GHz have been manufactured and experimentally verified at the European High-Power Radiofrequency Space Laboratory. This measurement campaign shows peak power thresholds up to 1.09 kW and 3.59 kW at 600 mbar for the non- and full-optimized GGW BPFs, respectively, thereby demonstrating a PPHC enhancement up to 5.16 dB in the high-pressure range when both strategies, proposed in this work, are used.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Agrupación de ranuras alimentadas por una novedosa guía semi-modo en Gap Waveguide

  • Ferrando-Rocher, Miguel
  • Pérez-Guimerá, Alejandro
  • Herranz-Herruzo, Jose Ignacio
  • Valero-Nogueira, Alejandro
  • Marini, Stephan
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
This paper presents a novel antenna feed network that significantly facilitates the design and fabrication in Gap Waveguide technology. In particular, a 1x4 linearly polarized Ka-band antenna array with a novel corporate distribution network using a half-mode groove-gap waveguide (HM-GGW). The good simulated results obtained from 29 GHz to 31 GHz by this breadboard give the first validity to this new development for GW.
Repositorio Digital UPCT
Publicación Artículo científico (JournalArticle)

Multimode Equivalent Networks for Shielded Microwave Circuits With Thick Metallizations

  • Gómez Molina, Celia
  • Quesada Pereira, Fernando Daniel
  • Marini, Stephan
  • Melcón Álvarez, Alejandro
  • Boria Esbert, Vicente Enrique
  • Guglielmi, Marco
In this article, we show how the multimode equivalent network (MEN) technique can be extended to the analysis of multilayer boxed planar microwave circuits that are built using a thick metallization. This analysis is carried out considering the thick metallic circuit as a length of the uniform waveguide. The problem is then divided into two waveguide steps (or junctions). We first obtain the equivalent network of the two junctions. Then, we cascade them to obtain the MEN of the complete circuit, thereby including the effect of finite thickness rigorously. A key aspect of the formulation that we propose is that it includes ports in the transverse plane of the circuit. In addition to theory, several shielded microwave filters using a thick metallization are also analyzed. An in-depth study of the numerical convergence is also performed for two practical examples. Simulation results are shown to be in good agreement with both commercial simulation tools and measurements, thereby fully validating our theoretical formulation., This work was supported in part by the Ministerio de Educación, Cultura y Deporte, Spanish Government, under Grant FPU15/02883; and in part by the Ministerio de Ciencia e Innovación through the sub-projects C41, C42 and C43 of the coordinated project under Grant PID2019-103982RB