DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación
Set de datos (Dataset)
Supporting Information for A new quasi-solid polymer electrolyte for next-generation Na–O2 batteries: unveiling the potential of a polyamide-polyether system [Dataset]
Under a Creative Commons BY 4.0 license., Figures:
Figure S1. The synthetic route for the Pebax®1657 membrane via solvent evaporation method.
Figure S2. SEM micrographs corresponding of the Celgard separator (a) and Pebax®1657 membrane (b), air permeability assessed via Gurley measurements (c), N2 adsorption-desorption isotherm at -196 ºC (77K) (d).
Figure S3 Electrolyte uptake of the Celgard separator and Pebax®1657 membrane as a function of time (a), Nyquist plots (b), and the correlation between electrolyte uptake and ionic conductivity for Celgard/L.E. and Pebax®1657 QSPE (c). Both polymers were immersed in 1M NaTFSI/diglyme electrolyte.
Figure S4. NMR spectra of the 1M NaTFSI/diglyme electrolyte after immersion of the Pebax®1657 membrane for 48 hours, compared to NaTFSI/diglyme control and using deuterated dimethyl sulfoxide (DMSO-d6) as the reference solvent: (a) 1H-NMR; (b) 23Na-NMR; (c) 19F-NMR.
Figure S5. Raman spectra of NaTFSI/diglyme electrolyte, Pebax®1657 membrane, and Pebax Pebax®1657 QSPE, and Pebax®1657 QSPE after cycling showing different regions of the spectrum. The Pebax®1657 membrane was immersed in 1M NaTFSI/diglyme and dried before analysis.
Figure S6. The proposed mechanism for Na+ ion transport via Pebax®1657 QSPE
Figure S7. ATR-FTIR spectra (a) and XRD patterns (b) of Celgard separator, NaTFSI/diglyme, and Celgard/L.E.
Figure S8. The correct XRD patterns and the Full Width at Half Maximum (FWHM) via the Pseudo-Voigt function for Pebax®1657 membrane and Pebax®1657 QSPE impregnated with NaTFSI/diglyme.
Figure S9. SEM cross-section of Pebax®1657 QSPE (a) and EDS-SEM mapping for the Pebax®1657 QSPE showing the distribution of Na, F, and S elements within the membrane matrix (b and c).
Transference number calculations
Figure S10. LSV profiles using unsymmetrical coin cells (Na| Celgard/L.E.|SS; Na| The Pebax®1657 QSPE |SS) with scan rate 1 mV/s, (a), Nyquist plots before and after polarization, (b), and chronoamperometry curves (CA) for Celgard/L.E. and Pebax®1657 QSPE with PEIS measurements (c).
Figure S11. Voltage profiles of Na|Na symmetrical cells using Celgard/L.E (a and c) Pebax®1657 QSPE (b and f) for different stags long-term galvanostatic cycling at current density (75 µA cm-2), respectively.
Figure S12. Raman spectra of the air cathodes discharged at a-b)75 µA cm-2 and c-d) 150 µA cm-2, for the Swagelok-type Na-O2 batteries using a-c) Celgard/L.E. and b-d) Pebax®1657 QSPE.
Figure 13. SEM imaging of the cathode/electrolyte interface after discharge at different current densities; a-b)75 µA cm-2 and c-d) 150 µA cm-2, for the batteries assembled using a) Celgard/L.E. and Pebax®1657 QPE systems.
Figure S14. Galvanostatic discharge/charge (shallow cyclability) curves at current densities (75 µA cm-2 and 150 µA cm-2) for the Swagelok-type Na-O2 batteries assembled cells using Celgard/L.E. (a and c) and Pebax®1657 QSPE (b and d) to a limited capacity (0.25 mAh cm-2) and Cut-off potential (1.8 V). The charge overpotential evolution during cycling for both Celgard/L.E. and Pebax®1657 QSPE at the two current densities (75 μA cm-2 and 150 μA cm-2) (e). Both polymers were immersed in 1 M NaTFSI/diglyme inside the glovebox.
Figure S15. SEM imaging and digital photos of the pristine Na anode (a, d) and Na anode for the discharged Swagelok-type Na-O2 batteries assembled cells at current density (75 µA cm-2) using Pebax®1657 QSPE (b, e) and Celgard/L.E. (c, f).
Tables:
Table S1. The assigned chemical-shifts for the liquid electrolyte (NaTFSI/diglyme) as observed in the NMR spectra.
Table S2. The assigned FTIR bands of the Pebax®1657 QSPE, Pebax®1657 membrane, NaTFSI/diglyme electrolyte, Celgard membrane, and Celgard/L.E, respectively.
Table S3. The assigned Raman bands of the NaTFSI/diglyme electrolyte, Pebax®1657 membrane, Pebax®1657 QSPE, and Pebax®1657 QSPE, respectively.
Table S4. Comparison of the electrochemical performance of this work with reported polymer electrolytes for Na-O2 batteries in the literature.
Table S5. Comparison of the electrochemical performance of this work with reported polymer electrolytes for Na ion batteries in the literature.
References., M.Y. acknowledges the Marie Sklodowska-Curie Actions (MSCA-IF) grant “101067009” funded by the European Union's Horizon research and innovation programme. N.O.-V. acknowledges grant RYC2020–030104-I funded by MICIU/AEI/ 10.13039/501100011033 and by ESF Investing in your future. C.P.G. thanks the grant PID2023-150574NB-I00 funded by MICIU/AEI/ 10.13039/501100011033 and ERDF/EU., Peer reviewed