Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

Synthesis of anodized WO3 nanocatalysts using Melia azedarach leaves extract for energetic applications [Dataset]

  • Fernández Domene, Ramón Manuel
  • Solsona Espriu, Benjamin Eduardo
  • Erans Moreno, María
  • Blasco-Tamarit, E.|||0000-0001-7314-082X
  • Sánchez Tovar, Rita
This study reports the bio-mediated synthesis of tungsten trioxide nanostructures from aqueous extracts of Melia azedarach (L.) dry leaves. The synthesis was carried out by electrochemical anodization of tungsten foils in the presence of different volume percentages of leaves extracts. These nanostructures were afterwards characterized by X-Ray Diffraction (XRD), impedance measurements and linear sweep voltammetry in the presence of simulated solar light. Finally, these nanoelectrodes were used as (photo)electrocatalysts in the photoelectrochemical water splitting process to obtain green hydrogen and as anodes in Li-ion rechargeable batteries. Description of methods used for collection/generation of data: - Synthesis of WO3 nanostructures: The leaves of M. azedarach were randomly sampled from several mature trees from the surroundings of the Burjassot Campus of the University of Valencia (Spain). Fresh leaves were rinsed with tap and distilled water and subsequently air-dried indoors for 1 week, at room temperature. The extracts were obtained from dried leaves, by mixing 15 g of material with 150 mL of distilled water at 60 ºC. The infusion was maintained at that temperature for 20 min. After that, the solution, once cooled, was filtered through filter paper and used to prepare the different reaction media. Nanostructures of WO3 were synthesized by subjecting tungsten foils (1,3 cm2 of exposed area) to an anodization process with a cell potential of 20 V, for 4 h. A platinum foil served as the cathode within the cell. The anodization process employed an aqueous electrolyte composed of 1.5 M methanesulfonic acid (MSA) with varying proportions of M. azedarach leaves extract (from 0% to 10%, in volume), at a temperature of 50◦C. Anodization was performed under controlled hydrodynamic conditions, by means of a Rotating Disk Electrode (RDE) set a constant rotation speed of 750 rpm. Following anodization, a thermal treatment (annealing) was carried out in a tubular oven at 600◦C for 4 h in an air atmosphere to obtain crystalline WO3 nanostructures. - Morphological and structural characterization: X-Ray diffraction analyses (XRD) were performed to investigate the crystallinity of the WO3 samples. A D8AVANCE diffractometer (Bruker) equipped with a monochromatic Cu Kα1 source was used. -(Photo)electrochemical characterization: impedance measurements and photocurrent density vs potential curves: Electrochemical characterization of the WO3 nanostructures was conducted through impedance measurements, performing Electrochemical Impedance Spectroscopy (EIS) and Mott-Schottky (MS) analyses. All electrochemical tests were carried out using a three-electrode cell with the nanostructures acting as working electrodes, a silver/silver chloride (3 M KCl) electrode was the reference electrode and a platinum tip served as counterelectrode. Measurements were performed with a PalmSens4 potentiostat and 0.1 M H2SO4 was used as electrolyte. The sample area exposed to that electrolyte was 0.5 cm2. For EIS, a constant potential of 1 V was selected with an amplitude of 10 mV, scanning the frequency from 100 kHz to 10 mHz. For MS analysis, a constant frequency of 5 kHz was used, while the potential was scanned from 1 V to 0.2 V at a rate of 50 mV/s. For the photoelectrochemical characterization of the WO3 nanostructures, the same experimental set-up was used, with the addition of a solar simulator with AM 1.5 conditions (100 mW/cm2). Linear voltammetries to obtain photocurrent density – potential curves were conducted from 0.2 V to 1.05 V, by applying dark-light pulses (16 s in the dark followed by 4 s with illumination) while the potential was scanned. - Evaluation of WO3 nanostructures as Li-ion battery anodes: WO3 nanostructures were evaluated as anodes (negative electrodes) for Li-ion batteries. For that purpose, Swagelok-type cells were used, with WO3 nanostructures acting as working electrodes and a metallic lithium foil acting as both the counter and the reference electrodes. Batteries were assembled inside an Ar-filled glove box, using 1 M LiPF6 in ethylene carbonate/dimethyl carbonate/diethyl carbonate 1:1:1 (v/ v/v) as electrolyte (Sigma-Aldrich) and a Whatman glass microfiber separator. After sealing the cells, they were cycled outside the glove box at room temperature, using a Biologic BCS-815 cyclic station. Galvanostatic charge/discharge curves were recorded at different cycling rates (from C/10–1 C, and returning to C/10) within a potential window between 1 V and 3.5 V vs Li/Li+.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

CuOx nanostrutures synthesized under hydrodynamic conditions photoelectrochemical applications [Dataset]

  • Sánchez García, Germán
  • Pérez Calvo, Alberto
  • Fernández Domene, Ramón Manuel
  • Blasco-Tamarit, E.|||0000-0001-7314-082X
  • Sánchez Tovar, Rita
  • Solsona Espriu, Benjamin Eduardo
CuOx (x = 1 and 2) nanostructures have been synthesized by electrochemical anodization in ethylene glycol based electrolytes using oxalic acid or NaF (with or without NaOH) as complexing agents. The influence of hydrodynamic conditions and time during anodization of copper have also been evaluated. An electrochemical and photoelectrochemical characterization of the nanostructures has been performed.