- Pérez Álvarez-Quiñones, Gloria
- Herrera Serrano, Leticia
- Alonso Rodríguez, Pablo
- Martínez, Arturo
- Montero, Israel
- Alonso, Carmen
- Frutos Vázquez, Borja
- Martín-Consuegra, Fernando
Upon reception of samples of urban materials from a manufacturer, a reference was assigned with the general format "X_Y_z", where "X" is a number identifying the manufacturer, "Y" is a number identifying the specific product and "z" is a code identifying the type of material according to its composition, its application within the urban envelope and the product type according to its format.
Generic information of the sample was collected in the database for each reference. This information includes three groups of data:
- Commercial information: name of the manufacturer and name of the commercial product.
- Sample classification: type of material according to its composition (lime-based, cement-based, organic-based, bituminous, ceramic, metallic, or stone), its application in the urban envelope (facade, pavement, roof, or combinations of these) and the type of product according to its format (paving stone, tile, floor tile, brick, sheet, slab, mortar, paint, plate, board or roof tile).
- Physical properties of the specific sample measured: sample surface shape, dimensions (in mm) and weight (in kg).
- Appearance of the specific sample measured: qualitative assessment of color, tone, texture to the touch and texture to the eye. These parameters strongly depend on the perception of the observer, although some general criteria were defined:
Color can take values Red, Pink, Orange, Yellow, Green, Blue, Purple, White (includes pure white, off-white and light beige), Grey, Black (only pure black), Brown (includes terracota, tan, taupe and beige when not light), Metallic and Multicolor. For non-uniform materials within the same color range, the color is assigned based on the overall appearance of the material.
Tone can take values Light, Medium and Dark and is relative to the specific color so it is not assigned for white and black colors.
Texture to the touch can take values: Smooth (only for perfectly smooth surfaces); Medium (includes surfaces with low and medium roughness); Rough (surfaces with high roughness) and Grooves (surfaces showing variations in height in defined directions).
Finally, the texture to the eye refers to the predominant surface appearance and can take values: Granular (grains are distinguishable either by surface voids or by a mixture of different materials); Wood (veining imitating the appearance of Wood); Marble (veining imitating the appearance of marble); Veined (areas of different appearance are distinguishable, either by different roughness, or by different colors and/or materials and the result imitates neither wood nor marble); Uniform (similar appearance and no grain across the entire surface); and Other., The samples were characterized to obtain the thermo-optical parameters.
- Reflectance spectra in the 380 nm - 1700 nm wavelength range were collected from one sample of each product using a fiber-optic portable equipment. For products with application in facades (only in facades or in facades and other applications) and for products with application only in roofs, a high-power tungsten halogen radiation source from Ocean Optics, a 50-mm integrating sphere from Ocean Optics and two spectrometers from Stellarnet (Black Comet for the 380-1050 nm wavelength range and Dwarf Star for the 900-1700 nm range) were used. For products with application only in pavements a tungsten halogen lamp with a color-equalizing filter from Stellarnet was used connected to the two spectrometers via a fiber optic reflectance probe from Ocean Optics, in which seven illumination fibers are located around a central reading fiber. The probe was placed at an angle of 90º/45º with respect to the sample surface for non-glossy/glossy samples.
For each sample, reflectance spectra were measured at different points following a pattern to cover the whole surface. From each spectrum measured in a sample, the visible reflectance (RV) and solar reflectance (RS) values were calculated following the procedure defined at the UNE EN 410:2011 standard; the visible/solar absorptance values (AV/AS) were calculated as the unity minus the corresponding reflectance value, as all the samples analyzed are opaque; and the color coordinates in the CIE 1976 L*a*b* colour space were calculated following the procedure defined at UNE-EN ISO/CIE 11664-4:2020 standard. The mean and standard deviation values of these parameters were collected for each sample in the database., - Emissivity data were collected from one sample of each product using an ET-100 portable emissometer from Surface Optics Corporation. The instrument measures the directional-hemispherical reflectance of the analyzed surface at two radiation incidence angles (20° and 60°), across six wavelength intervals covering the range of 1.5 to 21 µm. From the reflectance data, the instrument calculates the directional thermal emittance at 20° (E20) and at 60° (E60), and derives from the values obtained at 20° the hemispherical total emittance (EH) that represents the emissivity. For each sample, the surface was measured at different points following a pattern to cover the whole area. The mean and standard deviation values for the two directional and the hemispherical emittances of each sample were calculated by the equipment and collected for each sample in the database., Python code was used to process the spectra and make the necessary corrections to obtain the absolute total reflectance, to calculate the visible and solar reflectance/absortance values and the color coordinates from the reflectance spectra, and to collect all the information of each sample both in a database in Excel format and in a product sheet., This dataset compiles thermo-optical, physical and visual properties of 236 commercial urban materials commonly used in façades, roofs and pavements. The database includes information on material classification, physical characteristics, surface appearance, visible and solar reflectance, visible and solar absorptance, thermal emittance and CIE L*a*b* colour coordinates. Data were collected between January 2023 and July 2026 through laboratory measurements using standardized experimental procedures and processed with Python-based tools.
The dataset supports the characterization of urban materials and facilitates research on urban microclimates, building energy performance, thermal comfort, climate adaptation and the development of sustainable urban environments., This dataset was generated as part of the mateMad project (PID2020-114873RB-C31), funded by MCIN/AEI; the PAULIA project (CPP2022-009932), funded by MCIN/AEI and the European Union–NextGenerationEU/PRTR; and the ZEBAI project (Grant Agreement 101138678), funded by the European Union's Horizon Europe research and innovation programme., No, This dataset is Version 2 of Database of visible reflectance, solar reflectance and emissivity of urban materials. It supersedes the previous release by extending the temporal coverage (2023–2026), increasing the number of commercial urban materials from 181 to 236, and enriching the database with new physical, visual and thermo-optical information. In addition to visible reflectance, solar reflectance and emissivity, this version includes visible and solar absorptance, directional thermal emittance (E20 and E60), hemispherical thermal emittance (EH), CIE L*a*b* colour coordinates, and descriptive information on the materials' physical characteristics and surface appearance.