e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación
Tesis doctoral (DoctoralThesis)
Additive Manufacturing of CuCrZr via Powder Bed Fusion Electron Beam (PBF-EB) as high heat flux material for nuclear fusion applications, Fabricación aditiva de CuCrZr mediante fusión por haz de electrones en lecho de polvo (PBF-EB) como material de alto flujo térmico para aplicaciones de fusión nuclear
For decades, the pursuit of clean and sustainable electricity through nuclear fusion has stood as an elusive grail in humanity’s technological journey. We can not only witness this energy in our parent star, the Sun, but also feel it on our skin under its rays; yet replicating this complex phenomenon on Earth has always remained far beyond our grasp as a species. Today, experimental fusion devices such as ITER (International Thermonuclear Experimental Reactor) demonstrate that we are closer than ever to achieve this revolutionary breakthrough. This thesis shifts the focus beyond ITER towards DEMOnstration Power Plants (DEMO), conceptual reactors designed to prove in the future the feasibility of continuously delivering clean and safe net electricity to the grid.
Among the main challenges involved in developing DEMO fusion reactors, the materials challenge is paramount. The subject matter of this work is the class of High Heat Flux (HHF) materials required to manage extreme heat loads in these devices. To date, ITER-Grade CuCrZr (IG-CuCrZr, 0.6-0.9 Cr – 0.07-0.15 Zr – Bal. Cu (wt.%)) is the baseline heat sink alloy, chosen for its combination of high thermal conductivity and relatively high mechanical strength, combined with good fracture toughness, availability, and relatively low cost. Achieving the optimal precipitate microstructure in CuCrZr, however, demands precise post‑processing, and elevated temperatures can quickly degrade its performance.
The challenge intensifies during assembly, since high‑temperature joining methods such as welding, brazing or hot isostatic pressing (HIP), inevitably modify the optimised precipitate microstructure, thereby weakening the alloy’s mechanical and functional performance. Moreover, future DEMO reactors (and especially commercial fusion plants) will demand superior creep resistance, enhanced mechanical performance and robust behaviour under neutron irradiation. Under these conditions, IG‑CuCrZr is not expected to perform adequately: irradiation‑induced embrittlement below 275 °C, combined with long‑term creep requirements, further compromises its suitability. Various reinforcement strategies such as tungsten fibres or particles, and oxide‑dispersion‑strengthened (ODS) variants, are currently under investigation; however, this thesis takes Additive Manufacturing (AM) as a route by optimising advanced manufacturing processes with significant potential.
Over the last decade, AM has established itself as an emerging manufacturing technology with great potential in metallic materials. AM enables the manufacture of net-shaped parts with highly intricate internal cooling structures, and has a great potential for reducing the number of joining processes that would otherwise degrade critical microstructures for the performance of the material. This is particularly relevant in nuclear fusion applications, where components not only present complex geometries but also require strict minimisation of welds and joints, especially those involving filler material. In this context, AM is not just advantageous: it may in fact be the only viable fabrication route for certain components. The approach taken in this thesis is to go beyond the geometric and manufacturing advantages of AM and explore its potential to enhance material properties. Rather than solely addressing design and assembly challenges, AM is here considered as a powerful tool to engineer improved microstructures directly during fabrication. In doing so, this work demonstrates that AM can deliver Cu alloys with superior mechanical and functional performance compared to those produced through conventional processing routes.
In this thesis, the Powder Bed Fusion (PBF) AM technology has been employed, specifically the electron beam-based PBF (PBF-EB). Although this technique is less widespread than its laser-based (PBF-LB) counterparts, it is proposed here as the most suitable approach for processing Cu-based alloys for fusion applications, due to the limitations observed in PBF-LB. Issues such as excessive reflectivity, poor densification, and cracking have been consistently reported in laser-based fabrication of Cu-based materials. While near-full densification has indeed been achieved in recent studies, it has required highly optimised processing conditions and considerable effort in process development. In contrast, this work advocates for the use of the electron beam-based approach as a more appropriate route for processing Cu-based materials, particularly when high thermal conductivity, structural integrity, and microstructural control are simultaneously required.
In addition, the use of PBF-EB offers several further advantages over laser-based techniques, particularly relevant for the material under investigation in this work. First, the highly vacuum environment required by an electron beam system is especially beneficial when processing powders with high oxygen affinity, such as copper. This reduces oxidation during fabrication and, consequently, minimises the formation of oxide-induced porosity. A second key advantage relates to the dominant strengthening mechanism in CuCrZr: precipitation strengthening. The intrinsic preheating applied in PBF-EB (via both electron beam pre-scanning and sustained heating of the build platform) promotes an in-situ ageing process during fabrication. This results in the direct formation of a precipitation-hardened microstructure in the as-built condition, without the need for subsequent post-processing ageing treatments.
Therefore, this thesis constitutes a materials science investigation into the feasibility of the PBF-EB process for fabricating IG-CuCrZr heat sink material for nuclear fusion applications. To this end, key process parameters were systematically optimised to push final densification towards 100 %. An extensive parametric optimisation campaign was required to achieve this goal. The results obtained demonstrate that, while near-full densification and excellent microstructural quality can be reached, the process remains highly sensitive to parameter tuning and strongly dependent on the characteristics of the powder feedstock. This underlines the importance of tailoring both the powder morphology and the processing strategy to ensure consistent and reproducible results.
During the optimisation campaign, it was demonstrated that employing relatively low and constant electron beam scanning speeds (on the order of a few hundred mm/s) led to the best densification results. Interestingly, this is not typical in standard PBF-EB builds, where scan speeds often vary across different regions of the part. The optimised parameter set achieved in this study falls within what can be described as a slightly overmelted regime, based on the spherical microporosity observed in the fabricated specimens and in comparison with previous reports in the literature. This parameter set promoted a consistent overlapping of melt pools and remelting of previously deposited layers throughout the entire height of the specimens. As a result, the resulting microstructure was strongly influenced by these repeated thermal cycles, which played a key role in shaping grain morphology and precipitation behaviour.
Residual porosity is an inherent feature of AM and, as such, must be a central focus during process optimisation. It effectively becomes a screening criterion when assessing fabrication strategies. In this work, it has been demonstrated that the spherical and non-interconnected microporosity (and absent at the specimen surface) can be effectively removed through HIP, resulting in an average relative density level of 99.5%. While this is a very good value, it still indicates some room for further improvement. As expected, the remaining porosity has a measurable impact on thermal conductivity. However, experimental measurements conducted in this work fall within the typical variability range reported in the literature for IG-CuCrZr, namely between 320 and 380 W/m·K. These measurements were performed up to 400 °C, thus also confirming the thermal stability of the material within the operating range relevant to fusion applications. This confirms that the material, even in its current state of development, meets the thermal performance requirements for its intended application as a HHF material in nuclear fusion reactors.
Additive processes like PBF inherently generate extreme thermal gradients and very rapid solidification rates, producing non‑equilibrium, hierarchical microstructures that span several orders of magnitude in scale and demand exhaustive multiscale characterisation. While this is a general feature of PBF technologies, it becomes particularly relevant in PBF-EB due to the sustained preheating applied during processing and the formation of nanoscale precipitates directly in the as-built material. In this work, macro‑ and mesoscale features were first examined by optical microscopy (OM). Field‑Emission Scanning Electron Microscopy (FE-SEM) combined with Energy‑Dispersive X‑ray Sspectroscopy (EDS) then provided detailed insights into microscale characteristics, including the distribution and chemistry of precipitates. At the finest scale, Scanning/Transmission Electron Microscopy (S/TEM) resolved nanoscale features such as precipitates and dislocation networks formed during PBF‑EB. Finally, Electron Backscattered Diffraction (EBSD) was used to assess the crystallographic texture induced by fabrication, and orientation data were post-processed using the Bishop-Hill framework to compute the material’s Taylor factor.
This level of detailed characterisation is essential to understand the underlying mechanisms and dynamics that govern microstructure formation during fabrication. In this sense, the present work goes beyond validating the properties of the material obtained: it highlights how both processing parameters and post‑treatments can be used as active tools to tailor microstructures on demand for specific functional and mechanical requirements. AM is inherently anisotropic due to its layer-by-layer nature. Rather than being seen as a limitation, this anisotropy offers significant potential for designing processing strategies that promote the formation of substructures not typically accessible via conventional manufacturing methods. This opens the door to a new paradigm in which material properties can be engineered during fabrication through deliberate control of thermal histories and solidification paths.
The microstructural results obtained in this work provide compelling examples of tailored features achieved through process design. Elongated grains aligned along the build direction (BD) were observed, as expected in PBF processes. Interestingly, the combination of scan strategy and process parameters used in this study resulted in the development of corrugated grain boundaries, a microstructural feature with proven potential to enhance creep resistance by suppressing grain boundary sliding. This is particularly relevant for HHF components. At a finer scale, subgrains developed a cellular-like arrangement, with dislocation-rich cell walls. Such features have previously been linked to increased mechanical strength without compromising ductility, providing an intrinsic microstructural advantage.
Regarding precipitation, the as-built material already exhibited a refined distribution of strengthening precipitates (commonly known as Guinier-Preston zones), comparable in size and density to those reported in conventionally processed IG-CuCrZr. The average precipitate size was measured at ∼4.5 nm; however, a substantial population of larger precipitates in the 10-15 nm range was also identified. These larger precipitates are known to promote dislocation looping via the Orowan mechanism, which has been proposed as a promising strategy to mitigate irradiation-induced embrittlement. Therefore, this represents another tailored microstructural feature, specifically relevant for fusion environments. Finally, the presence of coarser precipitates located at grain and subgrain boundaries was also confirmed. Such a distribution plays a key role in enhancing creep resistance by reducing grain boundary sliding during prolonged thermal exposure, providing yet another example of process-driven tailoring for targeted performance.
The crystallographic texture developed was also characterised and the results revealed a fibre-type texture with <110> orientations preferentially aligned along BD, consistent with the epitaxial growth typically observed under steep thermal gradients. No cylindrical symmetry around BD was detected, confirming the presence of an inclined fibre texture. Pole figure analysis further enabled the identification and quantification of specific components within this fibre texture. Their evolution was monitored through post-processing thermal treatments of varying durations. The results showed that the dominant <110> || BD texture progressively transitioned into a <100> || BD orientation, with other components emerging depending on the thermal exposure. This transition has significant implications for the mechanical behaviour of the material.
To assess such implications, a novel methodology was developed in this thesis combining conventional texture analysis (such as pole figure and data orientation analysis) with Taylor factor computation based on the Bishop-Hill framework, as previously introduced. While grounded in established mathematical theories and models, its application to IG‑CuCrZr produced by PBF‑EB represents an original contribution, offering a new approach for quantifying crystallographic texture effects in additively manufactured materials. The results confirmed an initially anisotropic response, with high Taylor factors along BD averaging 3.34, compared to the 3.05 value obtained along the transverse direction. Notably, this transverse direction was aligned with the loading axis in the tensile tests. However, thermal treatments – particularly long-term (2 months) exposure at 375 °C – promoted a convergence of the Taylor factor values along BD and the transverse direction, both stabilising around ∼2.7. This trend towards mechanical isotropy is highly desirable for structural reliability in fusion components. Beyond its direct relevance to the alloy and process studied, this methodology can be extended to other materials and manufacturing routes, offering a powerful tool for designing and tailoring anisotropy in advanced structural materials.
Mechanical performance was evaluated through standard uniaxial tensile tests, miniaturised Charpy V‑notch impact tests for toughness, and Vickers microhardness measurements across different annealing conditions. These techniques are routinely employed for the qualification of structural materials and are therefore essential for assessing their suitability in demanding environments. Altogether, they provide a clear and quantitative understanding of how individual PBF‑EB parameters influence energy absorption, microstructural evolution and the mechanical behaviour of IG‑CuCrZr heat‑sink material.
The mechanical response obtained in this work was found to be comparable to, and in some cases even superior to, values reported in the literature for conventionally manufactured IG‑CuCrZr. These results support the initial hypothesis that not only can AM match the performance of traditional processing routes, but it also holds potential to enhance it. A comparison with recent studies on PBF-LB highlights a key distinction: in PBF-LB, the as-built microstructure tends to be a supersaturated solid solution due to the absence of powder preheating, resulting in poor mechanical performance unless a direct age-hardening (DAH) treatment is subsequently applied. Although such post-processing does lead to improved strength values (sometimes even exceeding those reported in this work) it reinforces the need for a dedicated ageing step in PBF-LB. In contrast, the preheating strategy inherent to PBF‑EB enables in-situ precipitation during fabrication, producing a strengthened microstructure directly in the as-built condition.
Hardness measurements revealed values consistently above the minimum recommended for IG‑CuCrZr components in ITER applications (126 HV), as well as above the typical range reported in the literature for conventionally processed material (120-140 HV). After HIP treatment, values between 157 and 174 HV were obtained across the various conditions evaluated. These high hardness values provide indirect evidence of the well-developed precipitation microstructure present in the material, although it is important to note that hardness is not governed exclusively by precipitation. Nevertheless, its sensitivity to microstructural features and the simplicity of the test makes hardness a valuable screening tool for rapid assessment of fabrication and heat treatment quality. In terms of toughness, miniaturised Charpy impact tests confirmed a good energy absorption capacity across all specimens. However, when compared to the upper range of values reported in the literature, the results suggest some room for improvement, likely linked to the residual ∼0.5% microporosity observed in the samples.
Beyond the core findings, this work also confirms and substantiates several relevant aspects regarding composition and processing that are critical for future developments. First, it has been demonstrated that a slight increase in Cr content beyond the upper limit defined for IG-CuCrZr does not lead to undesirable precipitate coarsening, suggesting a potential margin for mechanical performance enhancement without compromising thermal stability. Second, Zr has been found to have a particularly strong influence on mechanical strength. Based on the observed trends, this thesis advocates for a refined definition of allowable alloying element content (particularly Zr) within the current specification, to better align compositional choices with target performance requirements. Finally, the importance of minimising oxygen contamination throughout the entire fabrication chain was clearly confirmed. Although difficult to control, even modest increases in oxygen content were shown to impact densification and microstructural integrity, reaffirming the need for stringent powder handling and atmosphere control practices in AM of Cu-based alloys.
These results establish a solid foundation for the qualification of PBF‑EB materials in nuclear fusion systems and point towards future pathways for performance enhancement through alloy and process design., Durante décadas, la búsqueda de una fuente de electricidad limpia y sostenible a través de la fusión nuclear ha sido un objetivo esquivo en el camino tecnológico de la humanidad. Sentimos esta energía de nuestra estrella madre directamente en nuestra piel, bajo sus rayos; sin embargo, replicar este complejo fenómeno en la Tierra siempre ha estado fuera de nuestro alcance como especie. Hoy en día, dispositivos experimentales como ITER (Reactor Experimental Termonuclear Internacional) demuestran que estamos más cerca que nunca de lograr este avance revolucionario. Esta tesis dirige el foco más allá de ITER, hacia las futuras plantas de demostración (DEMO), reactores conceptuales diseñados para probar la viabilidad de suministrar de forma continua electricidad limpia y segura a la red. Entre los principales desafíos para el desarrollo de reactores de fusión tipo DEMO, el reto relacionado con los materiales es fundamental. El tema central de este trabajo se centra en los materiales sometidos a flujos térmicos intensos (High Heat Flux, HHF), necesarios para gestionar las elevadas cargas térmicas en estos dispositivos. Hasta la fecha, el CuCrZr grado ITER (IG-CuCrZr, 0.6–0.9 Cr – 0.07–0.15 Zr – resto Cu en %p) se considera la aleación base para disipadores térmicos, seleccionada por su combinación de alta conductividad térmica y resistencia mecánica relativamente elevada, junto con una buena tenacidad a fractura, disponibilidad y bajo coste. Sin embargo, lograr la microestructura óptima de precipitados en CuCrZr requiere tratamientos de post-procesado muy precisos, y las altas temperaturas pueden degradar rápidamente su rendimiento. Este reto se intensifica durante el ensamblaje, ya que los métodos de unión a alta temperatura como la soldadura, el brazing o el prensado isostático en caliente (HIP) modifican inevitablemente la microestructura optimizada, debilitando así el rendimiento mecánico y funcional de la aleación. Además, los futuros reactores DEMO (y especialmente las plantas comerciales) exigirán una resistencia al creep superior, mejor comportamiento mecánico y robustez frente a la irradiación neutrónica. En estas condiciones, no se espera que IG-CuCrZr rinda adecuadamente: la fragilización inducida por irradiación por debajo de 275 °C, junto con los requisitos de resistencia al creep a largo plazo, comprometen aún más su idoneidad. Si bien se están investigando estrategias de refuerzo como fibras o partículas de tungsteno y variantes reforzadas por dispersión de óxidos (ODS), esta tesis adopta la Fabricación Aditiva (Additive Manufacturing, AM) como vía alternativa mediante la optimización de procesos avanzados con alto potencial. Durante la última década, la AM se ha consolidado como una tecnología emergente con gran potencial en la fabricación de materiales metálicos. Permite la producción de piezas con geometrías finales e intrincadas estructuras internas de refrigeración, y tiene un enorme potencial para reducir el número de uniones que, de otro modo, degradarían microestructuras críticas. Esto resulta particularmente relevante en aplicaciones de fusión nuclear, donde los componentes no solo presentan geometrías complejas, sino que además requieren una estricta minimización de uniones, especialmente aquellas con material de aporte. En este contexto, AM no solo es ventajosa, sino que podría ser la única vía viable de fabricación para ciertos componentes. El enfoque de esta tesis va más allá de las ventajas geométricas y de fabricación, explorando el potencial de la AM para mejorar directamente las propiedades del material. En lugar de limitarse a abordar los desafíos de diseño y ensamblaje, aquí se considera la AM como una herramienta poderosa para diseñar microestructuras mejoradas directamente durante la fabricación. Así, se demuestra que la AM puede producir aleaciones de Cu con propiedades mecánicas y funcionales superiores a las obtenidas por rutas convencionales. En esta tesis se emplea la tecnología de AM por fusión en lecho de polvo (Powder Bed Fusion, PBF), concretamente la variante basada en haz de electrones (PBF-EB). Aunque esta técnica es menos común que su contraparte láser (PBF-LB), se propone aquí como la más adecuada para procesar aleaciones base cobre en aplicaciones de fusión, dadas las limitaciones observadas en PBF-LB. Problemas como alta reflectividad, baja densificación y agrietamiento son frecuentes en la fabricación láser de materiales base Cu. Aunque en estudios recientes se ha alcanzado una densificación casi completa, ha sido necesario un desarrollo de proceso muy optimizado. En cambio, este trabajo aboga por el uso de PBF-EB como una ruta más adecuada, especialmente cuando se requiere alta conductividad térmica, integridad estructural y control microestructural. Además, el uso de PBF-EB presenta ventajas adicionales especialmente relevantes para el material estudiado. Primero, las condiciones de alto vacío que requiere el sistema de haz de electrones es beneficioso al procesar polvos con alta afinidad por el oxígeno, como el cobre. Esto reduce la oxidación durante la fabricación y minimiza la formación de porosidad inducida por óxidos. En segundo lugar, el mecanismo de refuerzo dominante en CuCrZr es el endurecimiento por precipitación. El precalentamiento intrínseco en PBF-EB (por escaneado previo del haz y calefacción sostenida de la base) promueve un envejecimiento in situ durante la fabricación. Esto da lugar a una microestructura endurecida por precipitación directamente en la condición as-built, sin necesidad de tratamientos de envejecimiento posteriores. Por tanto, esta tesis constituye una investigación en ciencia de materiales sobre la viabilidad del proceso PBF-EB para fabricar CuCrZr de grado ITER como material disipador de calor en aplicaciones nucleares. Para ello, se optimizaron sistemáticamente los parámetros clave del proceso para alcanzar una densificación cercana al 100 %. Esto requirió una extensa campaña de optimización paramétrica. Los resultados muestran que, aunque se puede alcanzar una densificación casi total con buena calidad microestructural, el proceso sigue siendo muy sensible al ajuste fino de parámetros y fuertemente dependiente de las características del polvo de partida. Esto subraya la importancia de adaptar tanto la morfología del polvo como la estrategia de procesado para garantizar resultados reproducibles y consistentes. Durante la optimización, se demostró que el uso de velocidades de escaneado del haz relativamente bajas y constantes (del orden de unos cientos de mm/s) condujo a los mejores resultados de densificación. Esto no es habitual en construcciones estándar por PBF-EB, donde las velocidades suelen variar según la zona. El conjunto de parámetros optimizado en este estudio se sitúa en un régimen ligeramente sobrefundido, según la microporosidad esférica observada y en comparación con estudios previos. Este conjunto favoreció una superposición coherente de las melt pools y la fusión repetida de capas previas, influyendo fuertemente en la morfología de grano y en la precipitación. La porosidad residual es una característica inherente a la AM, y por tanto debe abordarse como un criterio de evaluación central. En este trabajo, se ha demostrado que la microporosidad esférica, no conectada y ausente en la superficie puede eliminarse eficazmente mediante HIP, alcanzando una densidad relativa media del 99,5 %. Aunque es un valor excelente, aún deja cierto margen de mejora. Como era de esperar, la porosidad restante afecta a la conductividad térmica. Sin embargo, las medidas experimentales se sitúan dentro del rango típico reportado para IG-CuCrZr (320-380 W/m·K). Estas medidas, realizadas hasta 400 °C, confirman la estabilidad térmica del material en el rango operativo relevante, cumpliendo con los requisitos funcionales como material HHF para reactores de fusión nuclear. Procesos aditivos como PBF generan gradientes térmicos extremos y velocidades de solidificación muy elevadas, dando lugar a microestructuras jerárquicas fuera de equilibrio que requieren una caracterización multiescala exhaustiva. Esto es especialmente relevante en PBF-EB debido al precalentamiento sostenido y la formación directa de precipitados nanoscópicos. En este trabajo, las características macro y mesoscópicas se analizaron mediante microscopía óptica, las características microscópicas mediante FE-SEM con EDS, y las nanoscópicas mediante S/TEM. Además, se caracterizó la textura cristalográfica con EBSD y se calcularon los factores de Taylor con el marco de Bishop-Hill. Este nivel de caracterización permite comprender los mecanismos que gobiernan la formación microestructural. Más allá de validar las propiedades del material, este trabajo demuestra cómo los parámetros de fabricación y tratamientos térmicos permiten ajustar microestructuras a medida para requisitos funcionales y mecánicos específicos. La AM es inherentemente anisotrópica debido a su naturaleza capa por capa, y el mismo proceso puede ser aprovechado para inducir subestructuras no accesibles por métodos convencionales, inaugurando un nuevo paradigma en el diseño de materiales. Los resultados microestructurales de este trabajo muestran características ajustadas mediante el diseño del proceso. Se observaron granos elongados alineados con la dirección de construcción (BD) y bordes de grano corrugados, que podrían mejorar la resistencia al creep al suprimir el deslizamiento intergranular. A escala más fina, los subgranos desarrollaron estructuras celulares ricas en dislocaciones. En cuanto a los precipitados, se observaron zonas Guinier-Preston de tamaño y densidad comparables a las obtenidas por procesamiento convencional, con precipitados de ∼4,5 nm y una fracción significativa en el rango 10-15 nm (relevantes para endurecimiento Orowan). También se identificaron precipitados gruesos en bordes de grano y subgrano, lo cual favorece la resistencia al creep. La textura cristalográfica desarrollada fue de tipo fibra con orientaciones <110> alineadas con BD, sin simetría cilíndrica e inclinada un cierto ángulo. El análisis de figuras de polos permitió identificar y cuantificar componentes específicos, cuyo comportamiento ante tratamientos térmicos se estudió. Se observó una transición de <110> || BD a <100> || BD, con implicaciones mecánicas relevantes. Para evaluar estos efectos, se desarrolló una metodología que combina análisis convencional de textura con el cálculo del factor de Taylor usando el marco Bishop-Hill. Su aplicación a CuCrZr procesado por PBF-EB representa una contribución original. Inicialmente se observaron factores de Taylor más altos en BD (3.34) frente a la dirección transversal (3.05), pero tras tratamiento térmico prolongado a 375 °C, ambos convergieron hacia ∼2.7, indicando una tendencia hacia la isotropía mecánica. Las propiedades mecánicas se evaluaron mediante ensayos de tracción, impacto Charpy miniaturizado y microdureza Vickers. Estos ensayos demostraron un comportamiento comparable, e incluso superior, al de CuCrZr convencional. La comparación con PBF-LB mostró que, en ese caso, el envejecimiento post-proceso es esencial para obtener buen rendimiento, mientras que en PBF-EB se consigue directamente en estado as-built gracias al precalentamiento. Las durezas obtenidas fueron consistentemente superiores al mínimo requerido para componentes de ITER (126 HV), alcanzando entre 157 y 174 HV tras HIP. Las pruebas de impacto indicaron buena tenacidad, aunque ligeramente inferior a los valores máximos reportados, probablemente por la microporosidad residual del 0,5 %. Finalmente, este trabajo confirma varios aspectos clave para desarrollos futuros. Se ha demostrado que un ligero aumento en el contenido de Cr no conlleva engrosamiento de precipitados, abriendo margen de mejora mecánica. También se ha constatado que el Zr influye fuertemente en la resistencia, proponiendo un ajuste más fino en las especificaciones actuales. Por último, se ha confirmado la importancia crítica de minimizar el oxígeno a lo largo de toda la cadena de fabricación. Incluso incrementos moderados impactan negativamente en la densificación y la integridad microestructural, subrayando la necesidad de un control atmosférico riguroso en la AM de aleaciones base Cu. Estos resultados sientan una base sólida para la cualificación de materiales PBF-EB en sistemas de fusión nuclear y apuntan hacia futuras estrategias de mejora mediante diseño de aleación y proceso., 1. Funding Entity: Strategic Projects Oriented towards Ecological Transition and Digital Transition (State Research Plan 2021-2023, Ministry of Science and Innovation), Reference: TED2021-129825A-I00.- 2. Funding Entity: Ministry of Science and Innovation (R&D Challenges Projects 2019), Reference: PID2019-105325RB-C31. - 3. Funding Entity: Community of Madrid. R&D Technologies Program Call 2018, Reference: S2018/EMT-4437. - 4. Title: Additive Manufacturing of CuCrZr - Characterization, Subprojects (WP) under GRANT 101052200 “EUROFUSION”, FP9. - 5. Funding Entity: CDTI/AEI, Call Transmisiones 2024, Reference: MIG-20242038/PLEC2024-011150., Programa de Doctorado en Ciencia e Ingeniería de Materiales por la Universidad Carlos III de Madrid, Presidenta: Marta Serrano García.- Secretaria: Carmen María Cepeda Jiménez.- Vocal: Gerald Pintsuk
Proyecto:
EC / HE 101052200