Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A modeling study on the combustion characteristics of alcohol/diesel dual fuel counterflow flame

  • Rahnama, Pourya
  • Somers, Bart
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
[EN] This study combines a 0D Well Stirred Reactor (WSR), 1D counterflow flame, experimental data, and a 1D gas dynamic model to create an integrated modeling tool to study the dual fuel combustion behavior in engine-relevant conditions, fueled with E85 and diesel fuels. First, the performance of a reduced chemical kinetic mechanism is studied, and the most important reactions are identified. Subsequently, the validated mechanism is utilized to investigate ignition and flame propagation characteristics, and to analyze the combustion mode in different thermal and compositional stratification levels. The results reveal that under the studied operating conditions, auto-ignition of the background mixture was unlikely due to long ignition delay times compared to experimental combustion durations. Instead, the combustion mode is more of a partially premixed flame and diffusive combustion influenced by reactivity and thermal stratification. The effects of thermal stratification revealed that at higher temperatures of the background mixture, the location of the most reactive mixture fractions moves to the richer sides. Notably, low-temperature ignition behavior reflects the existence of cool flame chemistry near the stoichiometric zone, where intermediate species like formaldehyde form before full heat release occurs. When the oxidizer temperature increases further, a secondary, most reactive mixture fraction can be observed on the oxidizer (lean) side. Temperature and heat release rate profiles also revealed that at lower oxidizer temperatures, the heat release rate shows more traditional diffusive combustion behavior. However, at elevated temperatures, the secondary heat release rate, which corresponds to flame propagation, becomes more prominent. Increasing the ratio of E85 to diesel also influences the partially premixed flame propagation and its heat release. When the oxidizer temperature or E85 content is increased, the location of the secondary heat release moves further away to the oxidizer side, away from the stoichiometric region., The authors would like to thank the financial support received through contract UPV-Subprograma 2 (PAID-01-22) del Vicerrectorado de Investigacion and Nederlandse Organisatie voor Wetenschappelijk Onderzoek (NWO) project number HiEff, 10022252, which was incremental in the development of this thesis at the Technical University of Eindhoven (TU/e) and I.U.I. CMT-Clean Mobility & Thermofluids, Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Combined 1D/3D Method to Accurately Model Fuel Stratification in an Advanced Combustion Engine

  • Sadloe, Adiel
  • Rahnama, Pourya
  • Somers, Bart
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
[EN] For computational fluid dynamic (CFD) modeling of advanced combustion engines, the cylinder is usually considered a closed system in which the initial conditions are estimated based on the experimental data. Most of these approximations hinder observing the effect of design parameters on engine performance and emissions accurately, and most studies are limited to a few design parameters. An approach is proposed based on the combination of a 1D gas dynamic and a 3D CFD model to simulate the whole engine with as few simplifications as possible. The impact of changing the in-cylinder initial conditions, injection strategy (dual direct injection or multiple pulse injections), and piston bowl geometry on a reactivity controlled compression ignition (RCCI) engine's performance, emissions, and fuel stratification levels was investigated. It was found that applying the dual direct injection (DDI) strategy to the engine can be promising to reach higher load operations by reducing the pressure rise rate and causing stronger stratification levels. Increasing the number of injection pulses leads to lower Soot/NOx emissions. The best reduction in the pressure rise rate was found by the dual direct strategy (38.36% compared to the base experimental case) and higher exhaust gas recirculation (EGR) levels (41.83% reduction in comparison with the base experimental case). With the help of a novel piston bowl design, HC and CO emissions were reduced significantly. This resulted in a reduction of 54.58% in HC emissions and 80.22% in CO emissions., This work was funded by the Netherlands Organisation for Scientific Research (NWO, project number HiEff, 10022252).