- Amirkhizi, Parisa
- Madre, M. A.
- Constantinescu, Gabriel
- Torres, M. A.
- Sotelo, Andres
- Kovalevsky, Andrei V.
- Rasekh, Shahed
This study explores the effect of single doping with different rare earth elements (Y, La, and Yb) on the structural, morphological and electrical properties of CaMnO3 bulk ceramics, aiming to improve their thermoelectric performance. Ca(1-x)RxMnO3 (R = Y, La, Yb; x = 0, 0.05, 0.10) samples were synthesized via a solid-state reaction. XRD analysis confirmed the thermoelectric CaMnO3 phase as the major one, with orthorhombic perovskite structure. Small amounts of secondary phases (CaMn2O4 and Mn2O3) were also detected in some doped samples. The addition of dopants influenced the unit cell parameters, producing a shift to lower 2θ angles, confirming their incorporation into the ceramic structure. SEM micrographs revealed a significant reduction in grain size upon doping. Electrical resistivity measurements showed a metallic behavior for all doped samples. The Y-doped samples exhibited the highest resistivity values while the Yb-doped samples showed the lowest values (6.8 mΩ cm for the 0.10 doped one), which are among the lowest found in literature for this compound. The Seebeck coefficient values show minor changes for 0.05 doped samples when they decreased with increasing concentration of dopant. Consequently, the highest values were observed for 0.05-doped sample (−215 µV/K), independently of the dopant. This value is much higher than the ones typically reported in the literature. The highest value of the power factor was calculated for the 0.05 Yb doped sample, reaching approximately 0.56 mW/K2·m at 800°C. This value is higher than the best presented in the literature for this compound, to the best of our knowledge, and suggests that Yb3+ doping greatly enhances the high-temperature thermoelectric performance of bulk CaMnO3 ceramics, making it a promising dopant for high-efficiency thermoelectric materials., The authors wish to thank the Gobierno de Aragón (Grupo de Investigacion T54_23R) for financial support. Sh. Rasekh acknowledges the support of the Research Employment Contract FCT–CEECIND/02608/2017. This work was also developed within the scope of the PhD project of P. Amirkhizi (grant 2020.08051.BD funded by FCT) and the project CICECO-Aveiro Institute of Materials, UIDB/50011/2020 (DOI 10.54499/UIDB/50011/2020), UIDP/50011/2020 (DOI 10.54499/UIDP/50011/2020), and LA/P/0006/2020 (DOI 10.54499/LA/P/0006/2020), financed by national funds through the FCT/MCTES (PIDDAC). Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. This article was supported by the projects UIDB/00481/2020 and UIDP/00481/2020—Fundação para a Ciência e a Tecnologia, DOI 10.54499/UIDB/00481/2020 (https://doi.org/10.54499/UIDB/00481/2020) and DOI 10.54499/UIDP/00481/2020 (https://doi.org/10.54499/UIDP/00481/2020). Gabriel Constantinescu acknowledges the support of the TEOsINTE project (Grant agreement ID: 101003375), funded under the H2020-EU.4. Programmes (Funding Scheme: MSCA-IF-EF-ST—Standard EF). M. A. Madre, M. A. Torres, and A. Sotelo acknowledge the grant CEX2023-001286-S funded by MICIU/AEI /10.13039/501100011033., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed