Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Measuring heat transfer processes in gully pots for real-time estimation of accumulated sediment depths

  • Regueiro-Picallo, Manuel
  • Moreno Rodenas, Antonio
  • Clemens-Meyer, Francois
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract:] The accumulation of sediments in stormwater systems negatively affects their functioning. For example, the re-suspension of these sediments can lead to serious pollution of surface water bodies through combined sewer overflows (CSOs). In addition, the persistent accumulation of sediments reduces the storage and hydraulic capacity of stormwater systems, resulting in an increased risk of flooding. Stormwater managers spend considerable resources cleaning these systems, but we still lack reliable and easy-to-use monitoring methods to provide information on the location, volume and composition of sediments. This study explores the use of temperature sensors combined with the analysis of heat transfer processes to measure sediment depth in sand trap gully pots. To this end, a laboratory-scale experimental campaign was carried out using a 1 : 1 scale gully pot model, with different sediment types, hydrographs and inflow temperature conditions. The experiments were designed using field measurements to reproduce the temperature changes in gully pots and thus the heat transfer processes. The results showed maximum differences between reference measurements and estimated depths of less than 30 mm. Finally, the use of temperature sensors as a cost-effective solution for monitoring sediment accumulation is discussed., The work developed by Manuel Regueiro-Picallo is funded within the postdoctoral fellowship programmes from the Xunta de Galicia (Consellería de Cultura, Educación e Universidade, ED481B-2021-082 and ED481D-2024-023). This work includes the results from a joint research activity funded by the EU under the Horizon 2020 INFRAIA program (Co-UDlabs project. GA No. 101008626). The authors are also indebted to the members of the ESF department of Deltares, in special Danko Boonstra, Christian van Nieuwenhuizen, Jelle Molenaar, Gerard Vaalburg, Richard Boele, Ben Boon and Jos Ooms, for their support during the experimental campaign. Funding for open access charge: Universidade da Coruña/CISUG., Xunta de Galicia; ED481B-2021-082, Xunta de Galicia; ED481D-2024-023
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Dataset on the Impacts of Sand and Leaf Litter on the Hydrological Performance of Green Roofs as Surrogate for Infiltration-Based Blue-Green Infrastructure (BGI)

  • Joshi, Prabhat
  • Naves, Juan
  • Anta, Jose
  • Maurer, Max
  • Leitão, J. P.
Data article. Data identification number: https://doi.org/10.25678/000DDP Direct URL to data: https://opendata.eawag.ch/dataset/bgi-maintenance-experiment., [Abstract]: This dataset contains raw and processed data from controlled experiments conducted in a rainfall simulator to quantify the impacts of incremental sand and leaf litter accumulation on the hydrological performance of blue-green infrastructure (BGI). The tests were conducted in a controlled indoor environment using two BGI boxes (approximately 3.84 m² each), representing a typical infiltration-based BGI setup with vegetation, a 6-cm deep substrate, and storage layers. Soil moisture sensors and tipping buckets were installed to measure underdrain flow. In one box, sand was incrementally added (2–18 kg.m−²); in the other, leaf litter accumulation ranged from 0.3 to 1.725 kg (total). Each scenario received rainfall (16.66 mm.h−1 for Box 1; 18.66 mm.h−1 for Box 2) for 30 minutes, with intervals larger than four hours between tests. The dataset can be used to understand the impact of shock events that introduce high pollutant loads to the BGI surface and subsurface, affecting their hydrological performance. It can also be used to study the maintenance needs of BGI to sustain their hydrological functionality., This work was partially funded by the EU under the Horizon 2020 program within a contract for Integrating Activities for Starting Communities (Co-UDlabs project. GA No.101008626). The corresponding author's doctoral study is partly funded by the Engineering for Development (E4D) scholarship, ETH Zürich., https://doi.org/10.25678/000DDP
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

The Role of Open Data in Regulating Combined Sewer Overflows

  • Schellart, Alma
  • Sharp, Liz
  • Bertrand-Krajewski, Jean-Luc
  • Rieckermann, Jörg
  • Anta, Jose
  • Blumensaat, Frank
  • Clemens-Meyer, Francois
  • Dittmer, Ulrich
  • Douterelo, Isabel
  • Gruber, Günter
  • Jensen, Henriette
  • Rokstad, Marius
  • Shucksmith, James
  • Tait, Simon
  • Tscheikner-Gratl, Franz
  • Verbeiren, Boud
  • Vezzaro, Luca
[Abstract]: The aim of this work is to investigate how open data can play a beneficial role in the regulation of combined sewer overflows (CSOs). The investigation consists of a review and critical discussion of historic CSO design, alongside more recent developments of regulations and emerging experiences of monitoring CSOs and different levels of data openness. The study focuses on practice in 10 European countries/regions. The novelty of this work comes from its review of historical development of design guidelines and regulations, shifts in the aims of these regulations, practicalities around implementation and testing of compliance, alongside the openness and availability of data. The main conclusions are that increasingly complex regulation goes hand in hand with limited compliance checking and opaque decision-making, whereas opening up relatively simplistic performance data has generated public and political discussion about urban drainage systems and the potential costs of improvements in water quality of the impacted surface water bodies. Making CSO data open does, however, need to be done with due care. Collaboration with trusted citizen groups, ensuring the data are correct, easy to access, and understand, as well as avoiding a blame culture are all of key importance., This project has received funding from the European Union's Horizon 2020 research and innovation programme under Grant Agreement No. 101008626 (the Co-UDlabs project).
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Clogging effects on a polyurethane-based permeable pavement under controlled laboratory settings

  • Alvarado-Vicencio, Reginald
  • Garcia Hernandez, Alvaro
  • Pimiento, María Alejandra
  • Naves, Juan
  • Anta, Jose
  • Born, Maximilian
  • Wintgens, Thomas
[Abstract] Permeable pavements are a well-established green solution for mitigating urban runoff, but their implementation in cities has been limited due to their low load-bearing capacity. Previous studies of a new polyurethane-based mixture, named Polyurethane Bound Permeable Mixture (PBPM), reported good resistance to heavy loads such buses and trucks. Nevertheless, PBPM remains susceptible to clogging caused by sediment accumulation transported by runoff. Consequently, this study investigated three mixtures under various clogging conditions: two PBPM mixtures with aggregate sizes of 8 mm (PBPM8) and 5 mm (PBPM5), and one bitumen-based mixture with an aggregate size of 8 mm (PA8) as control. Laboratory experiments were conducted using a rainfall simulator and real sediments to evaluate the impact of sediment particle size, sediment load, and rainfall intensity on the hydraulic conductivity (Kv). Three experiments were conducted: Experiment 1 determined the combination of rain intensity and sediment particle size distribution (PSD) that caused maximum clogging; Experiment 2 assessed Kv reduction with increasing sediment loads (applied in multiple steps) at a fixed rainfall intensity; and Experiment 3 examined Kv changes under different combinations of sediment loads (applied in one step) and rainfall intensities. PBPM exhibited superior clogging resistance, maintaining ∼40% of its initial Kv at 2000 g/m², outperforming PA8 and other bitumen-based mixtures. Clogging was exacerbated by shorter rains and specific sediment size distributions, whereas lower-intensity rainfall yielded inconsistent effects. Overall, Kv decreased proportionally with increasing sediment loads. These findings demonstrate that clogging severity is governed by rainfall characteristics (duration and intensity) and sediment properties (size, load, and application method); however, comparisons with previous research suggest that porosity is a greater influence than aggregate size. This study provides a framework for developing representative laboratory-scale clogging protocols and optimizing permeable pavement mixture designs., Becas Chile/DAAD; 7774/2021, Becas Chile/DAAD; PKZ 91795021
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Combining a daily temperature pattern analysis and a heat-pulse system to estimate sediment depths in sewer systems

  • Regueiro-Picallo, Manuel
  • Langeveld, Jeroen
  • Wei, Haoyu
  • Bertrand-Krajewski, Jean-Luc
  • Rieckermann, Jörg
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract:] Sediments in urban drainage systems (UDS) significantly impact their operation, so effective strategies are required to reduce their negative effects. Monitoring sediment accumulation provides valuable insights into sediment characteristics, sediment transport dynamics, and system performance. However, the effectiveness of monitoring systems is limited due to cost constraints and installation challenges. This study describes the development and application of a new system based on temperature dynamics to measure sediment depths in sewer systems. The methodology involves the analysis of temperature time series under dry weather flow conditions to identify harmonic patterns between wastewater and sediment-bed temperatures. These patterns are increasingly attenuated by increasing sediment depth. This study combines a system called MONitoring Temperatures in SEdiments (MONTSE), which integrates a dual-probe heat-pulse (DPHP) method to characterize sediment thermal properties, and a surrogate model, which includes temperature pattern analysis, to estimate sediment depths. Likewise, laboratory-scale experiments were performed to validate the temperature monitoring system and the surrogate model performance. The maximum absolute errors in measured sediment depths were less than 22 mm, and the uncertainty of the system was estimated at ±7.3 mm. Groundbreaking measurements of thermal properties of UDS sediments were also reported. Reliable information on sediment depths and properties was provided, so the system could significantly optimize sewer system operation and cleaning strategies., The work developed by M. R.-P. is funded within the postdoctoral fellowship programme from the Xunta de Galicia (Consellería de Cultura, Educación e Universidade, ED481B-2021-082). This work includes the results from a transnational access funded by the EU under the Horizon 2020 INFRAIA program (Co-UDlabs project. GA No. 101008626). The authors are indebted to all members of the Transnational Access HALL-Eawag User Group and the facility provider for their support in the experimental campaign. H. W. acknowledges support from the VINNOVA DRIZZLE – Centre for Stormwater Management (Grant: 2016–05176). Funding for open access charge: Universidade da Coruña/CISUG., Xunta de Galicia; ED481B-2021-082, Suecia. VINNOVA DRIZZLE - Centre for Stormwater Management; 2016-05176
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Understanding sediment wash-off in road drainage systems under intense rainfall and high sediment masses: Insights from a large-scale modeling facility

  • Zafra Mejía, Carlos Alfonso
  • Hernández Medina, David Santiago
  • Suárez-López, Joaquín
  • Naves, Juan
  • Anta, Jose
[Abstract] The main objective of this paper is to analyze, through a unique large-scale modeling facility, the RDS wash-off under various scenarios of intense rainfall and high RDS masses. A 1:1 scale physical modeling facility was used to allow precise measurement of the RDS wash-off phenomenon under two different rainfall intensities (30/50 mm/h) and three initial RDS masses (100/150/200 g/m2). The accumulated and discharged masses of RDS in the different components of the modeling facility (roadway/RW, gully pot/GP and manhole/MH) were collected at the end of the wash-off simulations. The results suggested the following sequence of intervention in the components of the drainage system to control pollution associated with fine RDS (< 63 μm): MH (59.2 %) > GP (31.2 %) > RW (9.6 %). The wash-off simulations suggested the following maximum (30/68 g/m2), minimum (16/38 g/m2) and minimum (2.15/2.61 g/m2) limits on the mass of RDS remaining on the RW, removed by the GP and discharged into the MH, respectively. These mass limits were relevant to understand the RDS behavior and to suggest improvement strategies for the RW cleaning systems (coarse/fine fractions washed-off: 80.3/81.7 %), GPs (coarse/fine fractions removed: 75.3/49.6 %) and MHs (coarse/fine fractions discharged: 5/32.1 %). Finally, the results suggested that the size fractions <63 μm and between 500 and 1000 μm were representative of the wash-off for the finest and coarsest fractions of the RDS, respectively., This work was supported by Co-UDlabs project, European Union's Horizon 2020 research and innovation program [Grant number 101008626].
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

The Value of Urban Drainage Systems Data: Facts, Discussions and Recommendations

  • Pimiento, Maria Alejandra
  • Nielsen, Jesper E.
  • Rasmussen, Michael R.
  • Brelot, Elodie
  • Bertrand-Krajewski, Jean-Luc
  • Schellart, Alma
  • Tait, Simon
  • Brüggemann, Thomas
  • Clemens-Meyer, Francois
  • Rieckermann, Jörg
  • Leitão, J. P.
  • Ciambra, Andrea
  • Naves, Juan
  • Anta, Jose
Forum paper / Note, [Abstract]: This paper synthesizes the outcomes of an international workshop organized within the EU-funded Co-UDlabs project, which brought together researchers and practitioners to discuss the value of UDS data and identify key barriers and opportunities. The findings emphasize the need for improved data governance frameworks, enhanced quality control procedures, and greater adoption of open data principles to unlock the full potential of UDS data. The paper concludes with a set of recommendations aimed at fostering collaboration across academia, industry and utilities, promoting transparency, and advancing data-driven urban water management strategies., This work was funded by the EU under the Horizon 2020 program within a contract for Integrating Activities for Starting Communities (Co-UDlabs project. GA No. 101008626); H2020 Research Infrastructures.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

European stakeholders’ visions and needs for stormwater in future urban drainage systems

  • Tondera, Katharina
  • Brelot, Elodie
  • Fontanel, Fanny
  • Cherqui, Frederic
  • Nielsen, Jesper E.
  • Brüggemann, Thomas
  • Naismith, Iain
  • Goerke, Marcel
  • Suárez-López, Joaquín
  • Rieckermann, Jörg
  • Leitão, J. P.
  • Clemens-Meyer, Francois
  • Moreno Rodenas, Antonio
  • Tait, Simon
  • Anta, Jose
[Abstract:] Transitioning urban drainage systems to serve water-smart societies requires the involvement of different disciplines and stakeholders. However, stakeholders have different visions and needs from the transitioning process (e.g in terms of financing, policy adaptation and system management) these also vary between regions and countries. Identifying such different needs for stakeholders is necessary to propose practical adaptation strategies. Therefore, evidence of needs as reflected in policy papers and legislation in seven European countries was collected. Knowledgeable individuals in the urban drainage community were asked about their visions. Results show that whilst there is consensus on the challenges, visions on how to transition are diverse, indicating that more interaction between the different stakeholder groups is required to develop consensus. Additionally, organisational and legislative structures often slow down the necessary change processes., Graduate School H2O’Lyon; ANR-17-EURE-0018, This research was carried out within the Collaborative Urban Drainage research labs communities - Co-UDlabs Project. Co-UDlabs has received funding from the European Union’s Horizon 2020 research and innovation programme under Grant Agreement No. 101008626. In France, this research was performed within the framework of the OTHU (Field Observatory for Urban Water Management – www.othu.org) and the Graduate School H2O’Lyon (ANR-17-EURE-0018).
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Towards urban drainage sediment accumulation monitoring using temperature sensors

  • Regueiro-Picallo, Manuel
  • Anta, Jose
  • Naves, Acacia
  • Figueroa, Alejandro
  • Rieckermann, Jörg
[Abstract:] Sewer sediments are among the main concerns related to urban drainage system management as they represent the largest contribution of suspended solid loads during rainfall events due to their resuspension. This study presents a novel methodology to detect and assess bed deposits in urban drainage systems based on temperature monitoring by using well-known thermodynamics and sediment properties. To illustrate the heat transfer processes in a liquid–sediment system and their relation to accumulation, a lab-scale experimental campaign was performed using sewer sediments and simulating water temperature gradients in sewers. Wastewater temperatures showed a marked daily pattern, while the presence of sediment dampened dynamics. Sediment thickness could therefore be estimated from the time evolution of the temperature differences measured between the bottom of the sediment bed and the water phase. Likewise, experimental data were used to calibrate a 1D heat transfer model, from which several sediment accumulation scenarios were simulated by using real wastewater temperature series. Thus, the influence of sediment properties on accumulation processes was assessed, and the range of potentially measurable sediments within an optimal range of [5–20] cm was identified. As a conclusion, temperature measurements and heat transfer model analysis can be used to approximate and monitor the sediments deposited in urban drainage systems. Future studies will extend the method to spatially-resolved sediment monitoring and active temperature sensing to improve sediment accumulation monitoring capabilities., The work developed by Manuel Regueiro-Picallo is funded within the postdoctoral fellowship programme from the Xunta de Galicia (Consellería de Cultura, Educación e Universidade). This work was partially founded by the EU under the Horizon 2020 program within a contract for Integrating Activities for Starting Communities (Co-UDlabs project. GA No.101008626). Finally, the authors would like to thank Raúl Pernas for his collaboration during part of the experimental campaign.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Flow rate influence on sediment depth estimation in sewers using temperature sensors

  • Regueiro-Picallo, Manuel
  • Schellart, Alma
  • Jensen, Henriette
  • Langeveld, Jeroen
  • Viklander, Maria
  • Lundy, Lian
The data collected in the laboratory-scale experimental campaign is openly accessible in ZENODO and available in these in-text data citation reference: Regueiro-Picallo et al. (2024b), with a license Creative Commons Attribution 4.0 International (CC BY-NC 4.0). https://doi.org/10.5281/zenodo.10821837, [Abstract:] Enhancing sediment accumulation monitoring techniques in sewers will enable a better understanding of the build-up processes to develop improved cleaning strategies. Thermal sensors provide a solution to sediment depth estimation by passively monitoring temperature fluctuations in the wastewater and sediment beds, which allows evaluation of the heat-transfer processes in sewer pipes. This study analyses the influence of the flow conditions on heat-transfer processes at the water–sediment interface during dry weather flow conditions. For this purpose, an experimental campaign was performed by establishing different flow, temperature patterns, and sediment depth conditions in an annular flume, which ensured steady flow and room-temperature conditions. Numerical simulations were also performed to assess the impact of flow conditions on the relationships between sediment depth and harmonic parameters derived from wastewater and sediment-bed temperature patterns. Results show that heat transfer between water and sediment occurred instantaneously for velocities greater than 0.1 m/s, and that sediment depth estimations using temperature-based systems were barely sensitive to velocities between 0.1 and 0.4 m/s. A depth estimation accuracy of ±7 mm was achieved. This confirms the ability of using temperature sensors to monitor sediment build-up in sewers under dry weather conditions, without the need for flow monitoring., The experimental campaign was funded by the EU under the Horizon 2020 INFRAIA program (Co-UDlabs project. GA No. 101008626). The work developed by Manuel Regueiro-Picallo was funded within the postdoctoral fellowship programme from the Xunta de Galicia (Consellería de Cultura, Educación e Universidade, ED481B-2021-082)., Xunta de Galicia; ED481B-2021-082
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Large-scale clogging experiments assessing the hydraulic performance of porous asphalt during their service life

  • Goya Heredia, Angélica Vanessa
  • Suárez-López, Joaquín
  • Naves, Juan
  • Anta, Jose
[Abstract]: This study investigates the long-term behaviour of a porous asphalt that retrofitted a 36 m² laboratory full-scale street section, in terms of filtration and clogging processes. Throughout 11 experiments with increasing accumulative sediment loads up to 5.5 kg/m², the evolution of surface permeability, water levels inside the asphalt, water flows, turbidity, and TSS concentrations were analyzed. Sediment loads, representing dry-weather buildup, were applied to the asphalt surface followed by simulated 30-minute 80 mm/h rain events. Findings revealed an average permeability reduction rate of 4717 mm/h per kg/m². Surface clogging appeared from a cumulative load of 4.0 kg/m², but the asphalt effectively managed rainfall with only marginal variations in flows and water levels, except for the vicinities of gully pots. The porous asphalt demonstrated a sediment retention efficiency of 93%, with a significant decrease in turbidity and increasing TSS concentrations once the asphalt clogged. Comparison with previous work emphasized the scalability and reliability of small-scale test results for analyzing permeability evolution and retention efficiency, but such tests overlook real-world heterogeneities compromising the representativeness of water and sediment fluxes. The experimental dataset provides novel and valuable data for developing models to accurately simulate permeable pavements towards better urban planning, design, and maintenance., This work was partially funded by the EU under the Horizon 2020 programme through a contract for Integrating Activities for Starting Communities (Co-UDlabs project, GA No.101008626) and by the projects POREDRAIN (grant number RTI2018-094217-B-C33) and SUDSlong-LCG (grant number PID2021-122946OB-C31) funded by MCIN/AEI/10.13039/501100011033 and by ‘ERDF A way of making Europe’. The experiments were carried out with the support of the research infrastructure at the Centre of Technological Innovation in Construction and Civil Engineering (CITEEC) at the University of A Coruña.