Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Smart-Sensors to Estimate Insulation Health in Induction Motors via Analysis of Stray Flux

  • Zamudio-Ramírez, Israel
  • Osornio-Rios, Roque Alfredo
  • Trejo-Hernandez, Miguel
  • Romero-Troncoso, Rene de Jesus
  • J. Antonino-Daviu|||0000-0003-1898-2228
[EN] Induction motors (IMs) are essential components in industrial applications. These motors have to perform numerous tasks under a wide variety of conditions, which affects performance and reliability and gradually brings faults and efficiency losses over time. Nowadays, the industrial sector demands the necessary integration of smart-sensors to effectively diagnose faults in these kinds of motors before faults can occur. One of the most frequent causes of failure in IMs is the degradation of turn insulation in windings. If this anomaly is present, an electric motor can keep working with apparent normality, but factors such as the efficiency of energy consumption and mechanical reliability may be reduced considerably. Furthermore, if not detected at an early stage, this degradation could lead to the breakdown of the insulation system, which could in turn cause catastrophic and irreversible failure to the electrical machine. This paper proposes a novel methodology and its application in a smart-sensor to detect and estimate the healthiness of the winding insulation in IMs. This methodology relies on the analysis of the external magnetic field captured by a coil sensor by applying suitable time-frequency decomposition (TFD) tools. The discrete wavelet transform (DWT) is used to decompose the signal into different approximation and detail coefficients as a pre-processing stage to isolate the studied fault. Then, due to the importance of diagnosing stator winding insulation faults during motor operation at an early stage, this proposal introduces an indicator based on wavelet entropy (WE), a single parameter capable of performing an efficient diagnosis. A smart-sensor is able to estimate winding insulation degradation in IMs using two inexpensive, reliable, and noninvasive primary sensors: a coil sensor and an E-type thermocouple sensor. The utility of these sensors is demonstrated through the results obtained from analyzing six similar IMs with differently induced severity faults., We would like to thank Consejo Nacional de Ciencia y Tecnologia (CONACYT) for providing economic support in this work (scholarship). Finally, thanks to the next projects: SEP-CONACYT 222453-2013, and FOFIUAQ-FIN201812. This wok was also funded by Spanish 'Ministerio de Ciencia Innovacion y Universidades' and FEDER program in the framework of the 'Proyectos de I+D de Generacion de Conocimiento del Programa Estatal de Generacion de Conocimiento y Fortalecimiento Cientifico y Tecnologico del Sistema de I+D+i, Subprograma Estatal de Generacion de Conocimiento' (ref: PGC2018-095747-B-I00).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Firm Performance in Regulated Markets: The Case of Spanish Defence Industry

  • Callado-Muñoz, Francisco J.
  • Hromcová, Jana
  • Sanso-Navarro, Marcos
  • Vera-Cabello, María
  • Utrero-González, Natalia|||0000-0001-9304-3517
[EN] This paper studies the effects of legal reforms associated with defence and public procurement on firm performance. With this aim, a theoretical framework for the reaction of defence firms to regulatory changes is developed. Its predictions have been empirically assessed using the last reforms implemented in Spain. Our results suggest that these new regulations have allowed the main defence contractors to outperform the other defence contractors in terms of productivity, having no effect on profitability. These findings are in line with theoretical priors. Therefore, it can be claimed that governmental interventions have had an effect on firm performance. We also provide evidence that, while the procurement procedures and the contract law put into place in 2011 have principally affected the productivity of large firms, the centralization process established in 2014 has exerted a higher influence on SMEs., This work was supported by the Ministry of Education and Science through grants ECO2016-76255-P and ECO2017-86305-C4-2-R, RTI2018-095799-B-I00; Government of Aragon - Spain-and FEDER COMPETE (S52_17R) research group and the Defence University Centre Zaragoza grants 2017-21 and 2018-12.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Integration in the European higher education area: the case of military education

  • Callado-Muñoz, F.J.
  • Utrero-González, N.
Military training has always been considered as an education system with its own characteristics that distinguished it from the rest of higher education. However, different initiatives have been developed in order to integrate military education in the European Higher Education Area (EHEA). This paper analyses the European system of military institutions of higher education (MHEI). Results indicate MHEI sector has distinctive features that have increased the diversity of European HEIs. Further, the emergence of the MHEI sector can have benefits for both the European defence and their educational attainment. From a defence point of view, it can help the development of a European strategic culture and increase cooperation between countries in defence and security. From the education area modernisation, it will improve defence and security related research and may enhance defence knowledge transfer. In this way, the MHEI sector will be positioned as key player in the development of the Common Security and Defence Policy and a European strategic culture.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Characterisation of Technological Collaborations and Evolution in the Spanish Defence Industry

  • Callado-Muñoz, F.J.
  • Fernández Olmos, M.
  • Ramírez-Alesón, M.
  • Utrero-González, N.
Collaboration with technological partners as an innovation strategy has become widespread in recent years, and all sectors are immersed in this process. In particular, the defence industry is characterised by the technological complexity of the products and services offered, together with a constant innovation process. However, data that allow us to identify characteristics that are found in collaboration contracts are not usually available in this sector. This paper addresses this gap in the literature by studying the different characteristics of both the technological partners and the development agreements for the 1999-2017 period. This is possible thanks to a database of more than 300 collaboration technology agreements between public and private organisations and the Spanish Ministry of Defence. The results provide the Ministry of Defence with a clear picture of the type of collaborations in the Defence industry, their partners and their behaviour under different economic conditions, which will help it identify the type of collaborations that can contribute to improving the design of its innovation strategy.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Polylactide, Processed by a Foaming Method Using Compressed Freon R134a, for Tissue Engineering

  • Aguado Sorolla, María|||0009-0009-6138-3467
  • Saldaña, Laura
  • Pérez del Río, Eduardo
  • Guasch, Judith|||0000-0002-3571-4711
  • Parera, Marc
  • Córdoba, Alba
  • Seras-Franzoso, Joaquin|||0000-0002-7893-4773
  • Cano-Garrido, Olivia|||0000-0002-5504-2131
  • Vázquez, Esther|||0000-0003-1052-0424
  • Villaverde, Antonio|||0000-0002-2615-4521
  • Veciana i Miró, Jaume|||0000-0003-1023-9923
  • Ratera Bastardas, Imma|||0000-0002-1464-9789
  • Vilaboa, Nuria|||0000-0003-4473-4498
  • Ventosa, Nora|||0000-0002-8008-4974
Fabricating polymeric scaffolds using cost-effective manufacturing processes is still challenging. Gas foaming techniques using supercritical carbon dioxide (scCO) have attracted attention for producing synthetic polymer matrices; however, the high-pressure requirements are often a technological barrier for its widespread use. Compressed 1,1,1,2-tetrafluoroethane, known as Freon R134a, offers advantages over CO in manufacturing processes in terms of lower pressure and temperature conditions and the use of low-cost equipment. Here, we report for the first time the use of Freon R134a for generating porous polymer matrices, specifically polylactide (PLA). PLA scaffolds processed with Freon R134a exhibited larger pore sizes, and total porosity, and appropriate mechanical properties compared with those achieved by scCO processing. PLGA scaffolds processed with Freon R134a were highly porous and showed a relatively fragile structure. Human mesenchymal stem cells (MSCs) attached to PLA scaffolds processed with Freon R134a, and their metabolic activity increased during culturing. In addition, MSCs displayed spread morphology on the PLA scaffolds processed with Freon R134a, with a well-organized actin cytoskeleton and a dense matrix of fibronectin fibrils. Functionalization of Freon R134a-processed PLA scaffolds with protein nanoparticles, used as bioactive factors, enhanced the scaffolds' cytocompatibility. These findings indicate that gas foaming using compressed Freon R134a could represent a cost-effective and environmentally friendly fabrication technology to produce polymeric scaffolds for tissue engineering approaches.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A Novel Generation of Tailored Antimicrobial Drugs Based on Recombinant Multidomain Proteins

  • López-Cano, Adrià
  • Ferrer-Miralles, Neus|||0000-0003-2981-3913
  • Sánchez, Julieta M.|||0000-0001-6676-5776
  • Carratalá, José Vicente|||0000-0001-6950-2939
  • Rodriguez Rodriguez, Xavier
  • Ratera Bastardas, Imma|||0000-0002-1464-9789
  • Guasch, Judith|||0000-0002-3571-4711
  • Pich, Oscar Q.|||0000-0003-3561-630X
  • Bierge, Paula|||0000-0003-0917-3445
  • García de la Mària, Cristina|||0000-0002-0585-9469
  • Miró, José M.|||0000-0001-8057-7755
  • Garcia-Fruitos, Elena|||0000-0001-7498-4864
  • Arís i Giralt, Anna|||0000-0001-7830-888X
Antibiotic resistance has exponentially increased during the last years. It is necessary to develop new antimicrobial drugs to prevent and treat infectious diseases caused by multidrug- or extensively-drug resistant (MDR/XDR)-bacteria. Host Defense Peptides (HDPs) have a versatile role, acting as antimicrobial peptides and regulators of several innate immunity functions. The results shown by previous studies using synthetic HDPs are only the tip of the iceberg, since the synergistic potential of HDPs and their production as recombinant proteins are fields practically unexplored. The present study aims to move a step forward through the development of a new generation of tailored antimicrobials, using a rational design of recombinant multidomain proteins based on HDPs. This strategy is based on a two-phase process, starting with the construction of the first generation molecules using single HDPs and further selecting those HDPs with higher bactericidal efficiencies to be combined in the second generation of broad-spectrum antimicrobials. As a proof of concept, we have designed three new antimicrobials, named D5L37βD3, D5L37D5L37 and D5LAL37βD3. After an in-depth exploration, we found D5L37D5L37 to be the most promising one, since it was equally effective against four relevant pathogens in healthcare-associated infections, such as methicillin-susceptible (MSSA) and methicillin-resistant (MRSA) Staphylococcus aureus, methicillin-resistant Staphylococcus epidermidis (MRSE) and MDR Pseudomonas aeruginosa, being MRSA, MRSE and P. aeruginosa MDR strains. The low MIC values and versatile activity against planktonic and biofilm forms reinforce the use of this platform to isolate and produce unlimited HDP combinations as new antimicrobial drugs by effective means.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Exploring the impact of the recombinant Escherichia coli strain on defensins antimicrobial activity, BL21 versus Origami strain

  • López-Cano, Adrià
  • Martínez-Miguel, Marc
  • Guasch, Judith|||0000-0002-3571-4711
  • Ratera Bastardas, Imma|||0000-0002-1464-9789
  • Arís i Giralt, Anna|||0000-0001-7830-888X
  • Garcia-Fruitos, Elena|||0000-0001-7498-4864
The growing emergence of microorganisms resistant to antibiotics has prompted the development of alternative antimicrobial therapies. Among them, the antimicrobial peptides produced by innate immunity, which are also known as host defense peptides (HDPs), hold great potential. They have been shown to exert activity against both Gram-positive and Gram-negative bacteria, including those resistant to antibiotics. These HDPs are classified into three categories: defensins, cathelicidins, and histatins. Traditionally, HDPs have been chemically synthesized, but this strategy often limits their application due to the high associated production costs. Alternatively, some HDPs have been recombinantly produced, but little is known about the impact of the bacterial strain in the recombinant product. This work aimed to assess the influence of the Escherichia coli strain used as cell factory to determine the activity and stability of recombinant defensins, which have 3 disulfide bonds. For that, an α-defensin [human α-defensin 5 (HD5)] and a β-defensin [bovine lingual antimicrobial peptide (LAP)] were produced in two recombinant backgrounds. The first one was an E. coli BL21 strain, which has a reducing cytoplasm, whereas the second was an E. coli Origami B, that is a strain with a more oxidizing cytoplasm. The results showed that both HD5 and LAP, fused to Green Fluorescent Protein (GFP), were successfully produced in both BL21 and Origami B strains. However, differences were observed in the HDP production yield and bactericidal activity, especially for the HD5-based protein. The HD5 protein fused to GFP was not only produced at higher yields in the E. coli BL21 strain, but it also showed a higher quality and stability than that produced in the Origami B strain. Hence, this data showed that the strain had a clear impact on both HDPs quantity and quality.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Design strategies for positively charged endolysins, Insights into Artilysin development

  • Carratalá, José Vicente|||0000-0001-6950-2939
  • Arís i Giralt, Anna|||0000-0001-7830-888X
  • Garcia-Fruitos, Elena|||0000-0001-7498-4864
  • Ferrer-Miralles, Neus|||0000-0003-2981-3913
Endolysins are bacteriophage-encoded enzymes that can specifically degrade the peptidoglycan layer of bacterial cell wall, making them an attractive tool for the development of novel antibacterial agents. The use of genetic engineering techniques for the production and modification of endolysins offers the opportunity to customize their properties and activity against specific bacterial targets, paving the way for the development of personalized therapies for bacterial infections. Gram-negative bacteria possess an outer membrane that can hinder the action of recombinantly produced endolysins. However, certain endolysins are capable of crossing the outer membrane by virtue of segments that share properties resembling those of cationic peptides. These regions increase the affinity of the endolysin towards the bacterial surface and assist in the permeabilization of the membrane. In order to improve the bactericidal effectiveness of endolysins, approaches have been implemented to increase their net charge, including the development of Artilysins containing positively charged amino acids at one end. At present, there are no specific guidelines outlining the steps for implementing these modifications. There is an ongoing debate surrounding the optimal location of positive charge, the need for a linker region, and the specific amino acid composition of peptides for modifying endolysins. The aim of this study is to provide clarity on these topics by analyzing and comparing the most effective modifications found in previous literature.