Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

Dipòsit Digital de la UB
Publicación Artículo científico (JournalArticle)

Large area in situ fabrication of Poly(pyrrole)-nanowires on flexible thermoplastic films using Nanocontact printing

  • Garcia-Cruz, Álvaro
  • Lee, Michael
  • Marote, Pedro
  • Zine, Nadia
  • Sigaud, Monique
  • Bonhomme, Anne
  • Pruna Morales, Raquel
  • López de Miguel, Manuel
  • Bausells, Joan
  • Jaffrezic, Nicole
  • Errachid, Abdelhamid
Abstract: Highly efficient nano-engineering tools will certainly revolutionize the biomedical and sensing devices research and development in the years to come. Here, we present a novel high performance conducting poly(pyrrole) nanowires (PPy-NW) patterning technology on thermoplastic surfaces (poly(ethylene terephthalate (PETE), poly(ethylene 2,6-naphthalate (PEN), polyimide (PI), and cyclic olefin copolymer (COC)) using nanocontact printing and controlled chemical polymerization (nCP-CCP) technique. The technique uses a commercial compact disk (CD) as a template to produce nanopatterned polydimethylsiloxane (PDMS) stamps. The PDMS nanopatterned stamp was applied to print the PPy-NWs and the developed technology of nCP-CCP produced 3D conducting nanostructures. This new and very promising nanopatterning technology was achieved in a single step and with a low cost of fabrication over large areas.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrochemical capacitive K+ EMIS chemical sensor based on the dibromoaza[7]helicene as an ionophore for potassium ions detection

  • Tounsi, Moncef
  • Zabala, Miguel
  • Bausells, Joan
  • Errachid, Abdelhamid
Tounsi, Moncef et al., A K+-sensitive capacitive electrolyte-membrane-insulator-semiconductor (EMIS) based on a novel dibromoaza[7]helicene ionophore has been developed. An ion-sensitive membrane based on polyvinylchloride (PVC) doped with the ionophore was deposited on the Si3N4/SiO2/Si-p/Cu-Al transducer. The properties of the K+-EMIS chemical sensor were investigated by electrochemical impedance spectroscopy (EIS). All the developed devices upon being tested have shown good sensitivity and linearity responses within the range 10-6 M to 10-1 M of potassium activity, with good selectivity over a wide variety of other cations (Na+, Li+, Cu2+, Ca2+, and Mg2+). To our knowledge, this is the first time that a capacitive field-effect sensor has been fabricated using helicene as a carrier for a K+-detection, combined with the structure Si3N4/SiO2/Si-p/Cu-Al as a transducer., We acknowledge the funding through the European Communities Seventh Framework Programme entitled Sea-on-a-Chip (FP7-OCEAN-2013) (No.614168), the European Union's Horizon 2020 Research and Innovation Programme entitled HEARTEN under grant agreement No 643694, NATO (CBP.NUKR.SFP 984173), and FP7-PEOPLE-2012-IRSES under the grant agreement No. 318053 (SMARTCANCERSENS). M. T. would like to acknowledge PHC-12 Mag088 project, and the Ministry of Higher Education and Scientific Research of Tunisia (LR11ES55)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of a novel capacitance electrochemical biosensor based on silicon nitride for ochratoxin A detection

  • Bougrinia, Madiha
  • Baraket, Abdoullatif
  • Jamshaid, Talha
  • El Aissari, Abdelhamid
  • Bausells, Joan
  • Zabala, Miguel
  • El Bari, Nezha
  • Bouchikhi, Benachir
  • Jaffrezic-Renault, Nicole
  • Errachid, Abdelhamid
  • Zine, Nadia
We report in this paper about the development of a novel capacitance electrochemical biosensor based on silicon nitride substrate (SiN) combined with a new structure of mangnetic nanoparticles (MNPs). SiN is highly stable as it was fabricated by a combination of several layers of Aluminum (Al), silicon p-doped (Si-p), silicon dioxide (SiO) and silicon nitride (SiN). This structure (SiN/SiO/Si-p/Al) has provided several advantages compared with other materials commonly used, and in particular in solid-state physics for electronic-based biosensors. The MNPs with terminated carboxylic acid were covalently bonded to SiN through a Self-Assembled Monolayers (SAMs) of the silane-amine (3-Aminopropyl) triethoxysilane (APTES). Finally anti-ochratoxin A antibodies were immobilized on MNPs by amide bonding. Contact Angle measurements, Atomic Force Microscopy, Scanning Electron Microscopy and Fluorescence Microscopy characterizations were performed during the biofunctionalization of the biosensor surface. Electrochemical measurements were carried out using Mott-Schottky analysis for ochratoxin A detection. The biosensor was highly sensitive and specific for ochratoxin A antigens, with a limit of detection of 4.57 pM, when compared to other interferences ochratoxin B and aflatoxin G1. The measurements were highly stable and reproducible for detection and interferences. The proposed method is very promising for ochratoxin A detection of several agro-food industry applications., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Silicon Nitride Capacitive Chemical Sensor for Phosphate Ion Detection Based on Copper Phthalocyanine – Acrylate-polymer

  • Barhoumi, Lassaad
  • Baraket, Abdoullatif
  • Nooredeen, Naglaa Mohammed
  • Ben Ali, Mounir
  • Nooredeen Abbas, Mohammed
  • Bausells, Joan
  • Errachid, Abdelhamid
In this work, we report the development of a highly sensitive capacitance chemical sensor based on a copper C,C,C,C-tetra-carboxylic phthalocyanine-acrylate polymer adduct (Cu(II)TCPc-PAA) for phosphate ions detection. A capacitance silicon nitride substrate based AlCu/Si-p/SiO2/Si3N4 structure was used as transducer. These materials have provided good stability of electro- chemical measurements. The functionalized silicon-based transducers with a Cu(II)Pc-PAA membrane were characterized by using Mott-Schottky technique measurements at different frequency ranges and for different phosphate concentrations. The morphological surface of the Cu(II) Pc-PAA modified silicon-nitride based transducer was characterized by contact angle measurements and atomic force microscopy. The pH effect was also investigated by the Mott-Schottky technique for different Tris-HCl buffer solutions. The sensitivity of silicon nitride was e studied at different pH of Tris-HCl buffer solutions. This pH test has provided a sensitivity value of 51 mV/decade. The developed chemical sensor showed a good performance for phosphate ions detection within the range of 10-10 to 10-5 M with a Nernstian sensitivity of 27.7 mV/decade. The limit of detection of phosphate ions was determined at 1 nM. This chemical sensor was highly specific for phosphate ions when compared to other interfering ions as chloride, sulfate, carbonate and perchlorate. The present capacitive chemical sensor is thus very promising for sensitive and rapid detection of phosphate in environmental applications., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Large area in situ fabrication of Poly(pyrrole)-nanowires on flexible thermoplastic films using Nanocontact printing

  • Garcia-Cruz, Álvaro
  • Lee, Michael
  • Marote, Pedro
  • Zine, Nadia
  • Sigaud, Monique
  • Bonhomme, Anne
  • Pruna Morales, Raquel
  • López de Miguel, Manuel
  • Bausells, Joan
  • Jaffrezic, Nicole
  • Errachid, Abdelhamid
Abstract: Highly efficient nano-engineering tools will certainly revolutionize the biomedical and sensing devices research and development in the years to come. Here, we present a novel high performance conducting poly(pyrrole) nanowires (PPy-NW) patterning technology on thermoplastic surfaces (poly(ethylene terephthalate (PETE), poly(ethylene 2,6-naphthalate (PEN), polyimide (PI), and cyclic olefin copolymer (COC)) using nanocontact printing and controlled chemical polymerization (nCP-CCP) technique. The technique uses a commercial compact disk (CD) as a template to produce nanopatterned polydimethylsiloxane (PDMS) stamps. The PDMS nanopatterned stamp was applied to print the PPy-NWs and the developed technology of nCP-CCP produced 3D conducting nanostructures. This new and very promising nanopatterning technology was achieved in a single step and with a low cost of fabrication over large areas.