Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optical and mechanical mode tuning in an optomechanical crystal with light-induced thermal effects

  • Navarro-Urrios, D.
  • Gomis-Bresco, J.
  • Capuj, N. E.
  • Alzina, F.
  • Griol Barres, Amadeu
  • Puerto Garcia, Daniel
  • Sotomayor-Torres, C. M.
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] We report on the modification of the optical and mechanical properties of a silicon 1D optomechanical crystal cavity due to thermo-optic effects in a high phonon/photon population regime. The cavity heats up due to light absorption in a way that shifts the optical modes towards longer wavelengths and the mechanical modes to lower frequencies. By combining the experimental optical results with finite-difference time-domain simulations, we establish a direct relation between the observed wavelength drift and the actual effective temperature increase of the cavity. By assuming that the Young's modulus decreases accordingly to the temperature increase, we find a good agreement between the mechanical mode drift predicted using a finite element method and the experimental one., This work was supported by the EU through the project TAILPHOX (ICT-FP7-233883) and the ERC Advanced Grant SOULMAN (ERC-FP7-321122) and the Spanish projects TAPHOR (MAT2012-31392). The authors thank A. Tredicucci for a critical reading of the manuscript and A. Pitanti for fruitful discussions.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A self-stabilized coherent phonon source driven by optical forces

  • Navarro Urríos, Daniel
  • Capuj, N. E.
  • Gomis-Bresco, J.
  • Alzina, F.
  • Pitanti, A.
  • Sotomayor Torres, C. M.
  • Griol Barres, Amadeu
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] We report a novel injection scheme that allows for phonon lasing in a one-dimensional optomechanical photonic crystal, in a sideband unresolved regime and with cooperativity values as low as 10-2. It extracts energy from a cw infrared laser source and is based on the triggering of a thermooptical/free-carrier-dispersion self-pulsing limit-cycle, which anharmonically modulates the radiation pressure force. The large amplitude of the coherent mechanical motion acts as a feedback that stabilizes and entrains the self-pulsing oscillations to simple fractions of the mechanical frequency. A manifold of frequency-entrained regions with two different mechanical modes (at 54 and 122 MHz) are observed as a result of the wide tuneability of the natural frequency of the self-pulsing. The system operates at ambient conditions of pressure and temperature in a silicon platform, which enables its exploitation in sensing, intra-chip metrology or time-keeping applications., This work was supported by the European Comission project TAILPHOX (ICT-FP7-233883), the ERC Advanced Grant SOULMAN (ERC-FP7-321122) and the Spanish MINECO project TAPHOR (MAT2012-31392). The authors sincerely thank B. Djafari-Rouhani, Y. Pennec and M. Oudich for the design of the OM photonic crystal, A. Trifonova, S. Valenzuela and E. Weig for a critical reading of the manuscript and A. Tredicucci for fruitful discussions. A. M and A. G thank L. Bellieres and N. Sanchez-Losilla for their contributions in the OM photonic crystal etching processes. DNU and JGB gratefully acknowledge the support of a Beatriu de Pinos and a Juan de la Cierva postdoctoral fellowship, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dynamical back-action at 5.5 GHz in a corrugated optomechanical beam

  • Navarro-Urrios, D.
  • Gomis-Bresco, J.
  • El-Jallal, S.
  • Oudich, M.
  • Pitanti, A.
  • Capuj, N.
  • Tredicucci, A.
  • Alzina, F.
  • Pennec, Y.
  • Djafari-Rouhani, B.
  • Sotomayor Torres, C.M.
  • Griol Barres, Amadeu
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] We report on the optomechanical properties of a breathing mechanical mode oscillating at 5.5 GHz in a 1D corrugated Si nanobeam. This mode has an experimental single-particle optomechanical coupling rate of vertical bar g(o, OM)vertical bar= 1.8 MHz (vertical bar g(o, OM)vertical bar/2 pi=0.3 MHz) and shows strong dynamical back-action effects at room temperature. The geometrical flexibility of the unit-cell would lend itself to further engineering of the cavity region to localize the mode within the full phononic band-gap present at 4 GHz while keeping high go, OM values. This would lead to longer lifetimes at cryogenic temperatures, due to the suppression of acoustic leakage., This work was supported by the EU through the FP7 project TAILPHOX (ICT-FP7-233883) and the ERC Advanced Grant SOULMAN (ERC-FP7-321122) and the Spanish projects TAPHOR (MAT2012-31392). D.N-U and J.G-B acknowledge support in the form of postdoctoral fellowships from the Catalan (Beatriu de Pinos) and the Spanish (Juan de la Cierva) governments, respectively.
Dipòsit Digital de la UB
Publicación Artículo científico (JournalArticle)

Thermal noise and optomechanical features in the emission of a membrane-coupled compound cavity laser diode

  • Baldacci, Lorenzo
  • Pitanti, Alessandro
  • Masini, Luca
  • Arcangeli, Andrea
  • Colangelo, Francesco
  • Navarro Urrios, Daniel
  • Tredicucci, Alessandro
We demonstrate the use of a compound optical cavity as linear displacement detector, by measuring the thermal motion of a silicon nitride suspended membrane acting as the external mirror of a nearinfrared Littrow laser diode. Fluctuations in the laser optical power induced by the membrane vibrations are collected by a photodiode integrated within the laser, and then measured with a spectrum analyzer. The dynamics of the membrane driven by a piezoelectric actuator is investigated as a function of air pressure and actuator displacement in a homodyne configuration. The high Q-factor (~3.4·104 at 8.3·10−3mbar) of the fundamental mechanical mode at ~73kHz guarantees a detection sensitivity high enough for direct measurement of thermal motion at room temperature (~87pm RMS). The compound cavity system here introduced can be employed as a table-top, cost-effective linear displacement detector for cavity optomechanics. Furthermore, thanks to the strong optical nonlinearities of the laser compound cavity, these systems open new perspectives in the study of non-Markovian quantum properties at the mesoscale.
Dipòsit Digital de la UB
Publicación Artículo científico (JournalArticle)

Far-field characterization of the thermal dynamics in lasing microspheres

  • Ramírez Ramírez, Joan Manel
  • Navarro Urrios, Daniel
  • Capuj, Néstor E.
  • Berencén Ramírez, Yonder Antonio
  • Pitanti, Alessandro
  • Garrido Fernández, Blas
  • Tredicucci, Alessandro
This work reports the dynamical thermal behavior of lasing microspheres placed on a dielectric substrate while they are homogeneously heated-up by the top-pump laser used to excite the active medium. The lasing modes are collected in the far-field and their temporal spectral traces show characteristic lifetimes of about 2 ms. The latter values scale with the microsphere radius and are independent of the pump power in the studied range. Finite-Element Method simulations reproduce the experimental results, revealing that thermal dynamics is dominated by heat dissipated towards the substrate through the medium surrounding the contact point. The characteristic system scale regarding thermal transport is of few hundreds of nanometers, thus enabling an effective toy model for investigating heat conduction in non-continuum gaseous media and near-field radiative energy transfer.
Dipòsit Digital de la UB
Publicación Artículo científico (JournalArticle)

Mechanical oscillations in lasing microspheres

  • Toncelli, A.
  • Capuj, Néstor E.
  • Garrido Fernández, Blas
  • Sledzinska, M.
  • Sotomayor Torres, Clivia M.
  • Tredicucci, Alessandro
  • Navarro Urrios, Daniel
We investigate the feasibility of activating coherent mechanical oscillations in lasing microspheres by modulating the laser emission at a mechanical eigenfrequency. To this aim, 1.5%Nd3+:Barium-Titanium-Silicate microspheres with diameters around 50 μm were used as high quality factor (Q>106) whispering gallery mode lasing cavities. We have implemented a pump-and-probe technique in which the pump laser used to excite the Nd3+ ions is focused on a single microsphere with a microscope objective and a probe laser excites a specific optical mode with the evanescent field of a tapered fibre. The studied microspheres show monomode and multi-mode lasing action, which can be modulated in the best case up to 10 MHz. We have optically transduced thermally-activated mechanical eigenmodes appearing in the 50-70 MHz range, the frequency of which decreases with increasing the size of the microspheres. In a pump-and-probe configuration we observed modulation of the probe signal up to the maximum pump modulation frequency of our experimental setup, i.e., 20 MHz. This modulation decreases with frequency and is unrelated to lasing emission, pump scattering or thermal effects. We associate this effect to free-carrier-dispersion induced by multiphoton pump light absorption. On the other hand, we conclude that, in our current experimental conditions, it was not possible to resonantly excite the mechanical modes. Finally, we discuss on how to overcome these limitations by increasing the modulation frequency of the lasing emission and decreasing the frequency of the mechanical eigenmodes displaying a strong degree of optomechanical coupling.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dynamical back-action at 5.5 GHz in a corrugated optomechanical beam

  • Navarro-Urrios, D.
  • Gomis-Bresco, J.
  • Capuj, Néstor E.
  • Alzina, Francesc
  • Sotomayor Torres, C. M.
Under the terms of the Creative Commons Attribution (CC BY) license to their work.-- et al., We report on the optomechanical properties of a breathing mechanical mode oscillating at 5.5 GHz in a 1D corrugated Si nanobeam. This mode has an experimental single-particle optomechanical coupling rate of |g o, OM | = 1.8 MHz (|g o, OM |/2π = 0.3 MHz) and shows strong dynamical back-action effects at room temperature. The geometrical flexibility of the unit-cell would lend itself to further engineering of the cavity region to localize the mode within the full phononic band-gap present at 4 GHz while keeping high g o, OM values. This would lead to longer lifetimes at cryogenic temperatures, due to the suppression of acoustic leakage., This work was supported by the EU through the FP7 project TAILPHOX (ICT-FP7-233883) and the ERC Advanced Grant SOULMAN (ERC-FP7-321122) and the Spanish projects TAPHOR (MAT2012-31392). D.N-U and J.G-B acknowledge support in the form of postdoctoral fellowships from the Catalan (Beatriu de Pinòs) and the Spanish (Juan de la Cierva) governments, respectively., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optical and mechanical mode tuning in an optomechanical crystal with light-induced thermal effects

  • Navarro-Urrios, D.
  • Gomis-Bresco, J.
  • Capuj, Néstor E.
  • Alzina, Francesc
  • Griol, Amadeu
  • Puerto, D.
  • Martínez, Alejandro
  • Sotomayor Torres, C. M.
Under the terms of the Creative Commons Attribution (CC BY) license to their work., We report on the modification of the optical and mechanical properties of a silicon 1D optomechanical crystal cavity due to thermo-optic effects in a high phonon/photon population regime. The cavity heats up due to light absorption in a way that shifts the optical modes towards longer wavelengths and the mechanical modes to lower frequencies. By combining the experimental optical results with finite-difference time-domain simulations, we establish a direct relation between the observed wavelength drift and the actual effective temperature increase of the cavity. By assuming that the Young's modulus decreases accordingly to the temperature increase, we find a good agreement between the mechanical mode drift predicted using a finite element method and the experimental one., This work was supported by the EU through the project TAILPHOX (ICT-FP7-233883) and the ERC Advanced Grant SOULMAN (ERC-FP7-321122) and the Spanish projects TAPHOR (MAT2012-31392)., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Far-field characterization of the thermal dynamics in lasing microspheres

  • Ramírez Ramírez, Joan Manel
  • Navarro Urrios, Daniel
  • Capuj, Néstor E.
  • Berencén Ramírez, Yonder Antonio
  • Pitanti, Alessandro
  • Garrido Fernández, Blas
  • Tredicucci, Alessandro
This work reports the dynamical thermal behavior of lasing microspheres placed on a dielectric substrate while they are homogeneously heated-up by the top-pump laser used to excite the active medium. The lasing modes are collected in the far-field and their temporal spectral traces show characteristic lifetimes of about 2 ms. The latter values scale with the microsphere radius and are independent of the pump power in the studied range. Finite-Element Method simulations reproduce the experimental results, revealing that thermal dynamics is dominated by heat dissipated towards the substrate through the medium surrounding the contact point. The characteristic system scale regarding thermal transport is of few hundreds of nanometers, thus enabling an effective toy model for investigating heat conduction in non-continuum gaseous media and near-field radiative energy transfer.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal noise and optomechanical features in the emission of a membrane-coupled compound cavity laser diode

  • Baldacci, Lorenzo
  • Pitanti, Alessandro
  • Masini, Luca
  • Arcangeli, Andrea
  • Colangelo, Francesco
  • Navarro Urrios, Daniel
  • Tredicucci, Alessandro
We demonstrate the use of a compound optical cavity as linear displacement detector, by measuring the thermal motion of a silicon nitride suspended membrane acting as the external mirror of a nearinfrared Littrow laser diode. Fluctuations in the laser optical power induced by the membrane vibrations are collected by a photodiode integrated within the laser, and then measured with a spectrum analyzer. The dynamics of the membrane driven by a piezoelectric actuator is investigated as a function of air pressure and actuator displacement in a homodyne configuration. The high Q-factor (~3.4·104 at 8.3·10−3mbar) of the fundamental mechanical mode at ~73kHz guarantees a detection sensitivity high enough for direct measurement of thermal motion at room temperature (~87pm RMS). The compound cavity system here introduced can be employed as a table-top, cost-effective linear displacement detector for cavity optomechanics. Furthermore, thanks to the strong optical nonlinearities of the laser compound cavity, these systems open new perspectives in the study of non-Markovian quantum properties at the mesoscale.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Mechanical oscillations in lasing microspheres

  • Toncelli, A.
  • Capuj, Néstor E.
  • Garrido Fernández, Blas
  • Sledzinska, M.
  • Sotomayor Torres, Clivia M.
  • Tredicucci, Alessandro
  • Navarro Urrios, Daniel
We investigate the feasibility of activating coherent mechanical oscillations in lasing microspheres by modulating the laser emission at a mechanical eigenfrequency. To this aim, 1.5%Nd3+:Barium-Titanium-Silicate microspheres with diameters around 50 μm were used as high quality factor (Q>106) whispering gallery mode lasing cavities. We have implemented a pump-and-probe technique in which the pump laser used to excite the Nd3+ ions is focused on a single microsphere with a microscope objective and a probe laser excites a specific optical mode with the evanescent field of a tapered fibre. The studied microspheres show monomode and multi-mode lasing action, which can be modulated in the best case up to 10 MHz. We have optically transduced thermally-activated mechanical eigenmodes appearing in the 50-70 MHz range, the frequency of which decreases with increasing the size of the microspheres. In a pump-and-probe configuration we observed modulation of the probe signal up to the maximum pump modulation frequency of our experimental setup, i.e., 20 MHz. This modulation decreases with frequency and is unrelated to lasing emission, pump scattering or thermal effects. We associate this effect to free-carrier-dispersion induced by multiphoton pump light absorption. On the other hand, we conclude that, in our current experimental conditions, it was not possible to resonantly excite the mechanical modes. Finally, we discuss on how to overcome these limitations by increasing the modulation frequency of the lasing emission and decreasing the frequency of the mechanical eigenmodes displaying a strong degree of optomechanical coupling.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Mechanical oscillations in lasing microspheres

  • Toncelli, Alessandra
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Garrido Fernández, Blas
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Tredicucci, Alessandro|||0000-0003-3619-3011
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
We investigate the feasibility of activating coherent mechanical oscillations in lasing microspheres by modulating the laser emission at a mechanical eigenfrequency. To this aim, 1.5%Nd3+:Barium- Titanium-Silicate microspheres with diameters around 50 lm were used as high quality factor (Q>106) whispering gallery mode lasing cavities. We have implemented a pump-and-probe technique in which the pump laser used to excite the Nd3+ ions is focused on a single microsphere with a microscope objective and a probe laser excites a specific optical mode with the evanescent field of a tapered fibre. The studied microspheres show monomode and multi-mode lasing action, which can be modulated in the best case up to 10 MHz. We have optically transduced thermally activated mechanical eigenmodes appearing in the 50-70MHz range, the frequency of which decreases with increasing the size of the microspheres. In a pump-and-probe configuration, we observed modulation of the probe signal up to the maximum pump modulation frequency of our experimental setup, i.e., 20 MHz. This modulation decreases with frequency and is unrelated to lasing emission, pump scattering, or thermal effects. We associate this effect to free-carrier-dispersion induced by multiphoton pump light absorption. On the other hand, we conclude that, in our current experimental conditions, it was not possible to resonantly excite the mechanical modes. Finally, we discuss on how to overcome these limitations by increasing the modulation frequency of the lasing emission and decreasing the frequency of the mechanical eigenmodes displaying a strong degree of optomechanical coupling.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A self-stabilized coherent phonon source driven by optical forces

  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • Alzina, Francesc|||0000-0002-7082-0624
  • Pitanti, Alessandro|||0000-0002-7027-0300
  • Griol, Amadeu|||0000-0002-5428-5713
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We report a novel injection scheme that allows for phonon lasing in a one-dimensional opto-mechanical photonic crystal, in a sideband unresolved regime and with cooperativity values as low as 10'2. It extracts energy from a cw infrared laser source and is based on the triggering of a thermo-optical/free-carrier-dispersion self-pulsing limit-cycle, which anharmonically modulates the radiation pressure force. The large amplitude of the coherent mechanical motion acts as a feedback that stabilizes and entrains the self-pulsing oscillations to simple fractions of the mechanical frequency. A manifold of frequency-entrained regions with two different mechanical modes (at 54 and 122MHz) are observed as a result of the wide tuneability of the natural frequency of the self-pulsing. The system operates at ambient conditions of pressure and temperature in a silicon platform, which enables its exploitation in sensing, intra-chip metrology or time-keeping applications.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Dynamical back-action at 5.5 GHz in a corrugated optomechanical beam

  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • El-Jallal, Said
  • Oudich, Mourad
  • Pitanti, Alessandro|||0000-0002-7027-0300
  • Capuj, Nestor Eduardo|||0000-0002-9042-2041
  • Tredicucci, Alessadro
  • Alzina, Francesc|||0000-0002-7082-0624
  • Griol, Amadeu|||0000-0002-5428-5713
  • Pennec, Yan|||0000-0002-4719-9913
  • Djafari-Rouhani, Bahram|||0000-0001-6983-9689
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We report on the optomechanical properties of a breathing mechanical mode oscillating at 5.5 GHz in a 1D corrugated Si nanobeam. This mode has an experimental single-particle optomechanical coupling rate of |g|=1.8 MHz (|g|/2π=0.3 MHz) and shows strong dynamical back-action effects at room temperature. The geometrical flexibility of the unit-cell would lend itself to further engineering of the cavity region to localize the mode within the full phononic band-gap present at 4 GHz while keeping high go, OM values. This would lead to longer lifetimes at cryogenic temperatures, due to the suppression of acoustic leakage.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Thermal noise and optomechanical features in the emission of a membrane-coupled compound cavity laser diode

  • Baldacci, Lorenzo
  • Pitanti, Alessandro|||0000-0002-7027-0300
  • Masini, Luca
  • Arcangeli, Andrea
  • Colangelo, Francesco
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Tredicucci, Alessandro|||0000-0003-3619-3011
We demonstrate the use of a compound optical cavity as linear displacement detector, by measuring the thermal motion of a silicon nitride suspended membrane acting as the external mirror of a near-infrared Littrow laser diode. Fluctuations in the laser optical power induced by the membrane vibrations are collected by a photodiode integrated within the laser, and then measured with a spectrum analyzer. The dynamics of the membrane driven by a piezoelectric actuator is investigated as a function of air pressure and actuator displacement in a homodyne configuration. The high Q-factor (~3.4 · 10 4 at 8.3 · 10 -3 mbar) of the fundamental mechanical mode at ~73 kHz guarantees a detection sensitivity high enough for direct measurement of thermal motion at room temperature (~87 pm RMS). The compound cavity system here introduced can be employed as a table-top, cost-effective linear displacement detector for cavity optomechanics. Furthermore, thanks to the strong optical nonlinearities of the laser compound cavity, these systems open new perspectives in the study of non-Markovian quantum properties at the mesoscale.