Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 19
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Detection of Invisible Damages in `Rojo Brillante¿ Persimmon Fruit at Different Stages Using Hyperspectral Imaging and Chemometrics

  • Munera, S|||0000-0003-3064-1186
  • Rodriguez-Ortega, Alejandro|||0000-0003-4781-6368
  • Aleixos Borrás, María Nuria|||0000-0001-6051-3375
  • Cubero, Sergio
  • Gómez-Sanchis, Juan
  • Blasco, José
[EN] The main cause of flesh browning in 'Rojo Brillante' persimmon fruit is mechanical damage caused during harvesting and packing. Innovation and research on nondestructive techniques to detect this phenomenon in the packing lines are necessary because this type of alteration is often only seen when the final consumer peels the fruit. In this work, we have studied the application of hyperspectral imaging in the range of 450-1040 nm to detect mechanical damage without any external symptoms. The fruit was damaged in a controlled manner. Later, images were acquired before and at 0, 1, 2 and 3 days after damage induction. First, the spectral data captured from the images were analysed through an algorithm based on principal component analysis (PCA). The aim was to automatically separate intact and damaged fruit, and to detect the damage in the PC images when present. With this algorithm, 90.0% of intact fruit and 90.8% of damaged fruit were correctly detected. A model based on partial least squares-discriminant analysis (PLS-DA), was later calibrated using the mean spectrum of the pixels detected as damaged, to determine the moment when the fruit was damaged. The model differentiated fruit corresponding correctly to 0, 1, 2 and 3 days after damage induction, achieving a total accuracy of 99.4%., This work is co-funded by the projects AEI PID2019-107347RR-C31, PID2019-107347RR-C32, PID2019-107347RR-C33, IVIA-GVA 51918 and the European Union through the European Regional Development Fund (ERDF) of the Generalitat Valenciana 2014-2020.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Near infrared hyperspectral imaging and spectral unmixing methods for evaluation of fiber distribution in enriched pasta

  • Teixeira Badaró, Amanda
  • Amigo, José Manuel
  • Blasco, Jose
  • Rios Ferreira, Amanda
  • Pedrosa Silva Clerici, Maria Teresa
  • Fernandes Barbin, Douglas
  • Aleixos Borrás, María Nuria|||0000-0001-6051-3375
[EN] Pasta is mostly composed by wheat flour and water. Nevertheless, flour can be partially replaced by fibers to provide extra nutrients in the diet. However, fiber can affect the technological quality of pasta if not properly distributed. Usually, determinations of parameters in pasta are destructive and time-consuming. The use of Near Infrared-Hyperspectral Imaging (NIR-HSI), together with machine learning methods, is valuable to improve the efficiency in the assessment of pasta quality. This work aimed to investigate the ability of NIR-HSI and augmented Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS) for the evaluation, resolution and quantification of fiber distribution in enriched pasta. Results showed R2V between 0.28 and 0.89, %LOF < 6%, variance explained over 99%, and similarity between pure and recovered spectra over 96% and 98% in models using pure flour and control as initial estimates, respectively, demonstrating the applicability of NIR-HSI and MCR-ALS in the identification of fiber in pasta., This work was supported by the Coordenaçao de Aperfeicoamento de Pessoal de Nivel Superior -Brasil (CAPES) [Finance Code 001]; Sao Paulo Research Foundation (FAPESP) [grant numbers 2008/57808-1, 2014/50951-4, 2015/24351-2, 2017/17628-3, 2019/06842-0]; and by GVA-IVIA and FEDER funds through project IVIA-51918. The authors would like to thank Nutrassim Food Ingredients company for the donation of the fiber samples, the support provided by Mrs. Cristiane Vidal during NIR-HSI system operation and data processing and Dr. Celio Pasquini for promptly receiving us in the laboratory that he coordinates (Grupo de instrumentaçao e automaçao em quimica analitica, Instituto de quimica, Universidade Estadual de Campinas, Campinas-SP, Brazil) to data acquisition.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Estudio y desarrollo de soluciones mecanizadas automatizadas mediante la aplicación de sensores y nuevas tecnologías para la producción de cítricos

  • González González, María Gyomar
[ES] El objetivo de esta Tesis Doctoral es generar conocimiento y tecnología que permitan desarrollar soluciones mecanizadas y automatizadas mediante la aplicación de sensores para monitorizar, optimizar tareas y aumentar la productividad en los cultivos de cítricos y, por ende, la competitividad del sector citrícola. Con este fin, se ha trabajado en la aplicación de tecnologías en algunas de las operaciones más importantes y costosas en la citricultura. En el ámbito de la recolección, con el objetivo de facilitar y optimizar el proceso de recolección de cítricos para consumo en fresco, se implementaron mejoras en un prototipo de plataforma autopropulsada de asistencia para garantizar la seguridad de los trabajadores y minimizar los riesgos laborales, asegurar la calidad de la fruta recolectada y clasificarla adecuadamente en función de su calidad por un sistema de visión artificial. Tras la implementación de estos avances, se evaluó su funcionalidad en condiciones reales de campo y se determinó el rendimiento de la operación de recolección asistida. Los resultados mostraron que el rendimiento operativo teórico en el proceso de recolección con la asistencia del prototipo fue un 17% menor que en la recolección manual tradicional. Asimismo, con la finalidad de generar de manera automática mapas de rendimiento en cítricos accesibles al agricultor, se creó una nueva herramienta a modo de cuadro de mando, denominada CitrusYield. Esta herramienta es capaz de obtener mapas que muestran la variabilidad, haciendo uso de la información proporcionada al inspeccionar cada fruta y de los datos obtenidos por los dispositivos de geolocalización, permitiendo conocer el rendimiento de la producción a nivel intraparcelario. Se evalúo el funcionamiento de CitrusYield con datos obtenidos por el prototipo. El cuadro de mando analizó los datos y generó diferentes mapas georreferenciando la información de la fruta con su punto de recolección. A través de estos mapas, CitrusYield demostró su capacidad para reflejar la heterogeneidad de la producción dentro de la parcela. Los indicadores de calidad, rendimiento del sistema de inspección por visión artificial y la productividad revelaron el grado de eficiencia del proceso de recolección con la asistencia del prototipo. En el ámbito de la detección temprana de plagas y enfermedades, se llevó a cabo la investigación del potencial de la imagen en color y de la imagen hiperespectral para la detección automática de daños causados por la plaga Tetranychus urticae en hojas de cítricos. Además, se diferenciaron en función de la antigüedad y de otros problemas que puede tener el árbol causados por deficiencias nutricionales o por otras plagas. En el análisis para identificar el daño causado por esta plaga, se obtuvo una tasa de éxito del 92,5% en las imágenes en color. No obstante, no se pudo discriminar la edad del daño. En las imágenes hiperespectrales, el éxito fue del 100% en la detección del daño y del 92% en la discriminación de la edad. En cuanto a la discriminación de daños de T. urticae respecto a otros daños, en las imágenes en color se obtuvo una tasa de éxito del 100% en la discriminación de Phyllocnistis citrella en el envés de las hojas. Las deficiencias de N no pudieron discriminarse correctamente y las deficiencias de Fe, Mn o Zn se detectaron acertadamente en el 50% de los casos. En las imágenes hiperespectrales, los daños por P. citrella se discriminaron con éxito en el 100% de los casos. Las deficiencias por N se discriminaron correctamente en más del 65% de los casos. No obstante, las deficiencias de Fe, Mn o Zn no pudieron ser discriminadas correctamente. Las conclusiones de esta Tesis Doctoral ponen de manifiesto el gran potencial de implementar estas tecnologías para monitorizar, optimizar tareas y digitalizar los procesos en las labores llevadas a cabo en los campos de cítricos, de manera que se logra aumentar la eficiencia, productividad y, también, la competitividad en el sector., [CA] L'objectiu d'esta Tesi Doctoral és generar coneixement i tecnologia que permeten desenvolupar solucions mecanitzades i automatitzades mitjançant l'aplicació de sensors per a monitoritzar, optimitzar tasques i augmentar la productivitat en els cultius de cítrics i, per tant, la competitivitat del sector citrícola. Amb este fi, s'ha treballat en l'aplicació de tecnologies en algunes de les operacions més importants i costoses de la citricultura. Amb l'objectiu de facilitar i optimitzar el procés de recol·lecció de cítrics per a consum en fresc es van implementar millores en un prototip de plataforma autopropulsada d'assistència per a garantir la seguretat dels treballadors i minimitzar els riscos laborals, assegurar la qualitat de la fruita recol·lectada i classificar-la adequadament en funció de la qualitat estimada pel sistema de visió artificial. Després de la implementació d'estos avanços, es va avaluar la seua funcionalitat en condicions reals de camp i es va determinar el rendiment de l'operació de recol·lecció assistida. Els resultats van mostrar que el rendiment operatiu teòric en el procés de recol·lecció amb l'assistència del prototip va ser un 17% menor que en la recol·lecció manual tradicional. Així mateix, amb la finalitat de generar de manera automàtica mapes de rendiment en cítrics accessibles a l'agricultor, es va crear una nova eina digital a manera de quadre de comandament, denominada CitrusYield. Esta eina és capaç d'obtindre mapes que mostren la variabilitat, fent ús de la informació proporcionada pel sistema de visió artificial i de les dades obtingudes pels dispositius de geolocalización, permetent conéixer el rendiment de la producció a nivell intraparcel·lari. El quadre de comandament va analitzar les dades i va generar diferents mapes georreferenciant l'informació de la fruita amb el seu punt de recol·lecció. A través d'estos mapes, CitrusYield va demostrar la seua capacitat per a reflectir l'heterogeneïtat de la producció dins de la parcel·la. Els indicadors de qualitat, rendiment del sistema d'inspecció per visió artificial i la productivitat calculats per CitrusYield van revelar el grau d'eficiència del procés de recol·lecció amb l'assistència del prototip. En l'àmbit de la detecció de plagues i malalties de cítrics, es va dur a terme la investigació del potencial de la imatge en color i de la imatge hiperespectral, per a la detecció automàtica de danys causats per la plaga Tetranychus urticae en fulls de cítrics. A més, es van discriminar en funció de l'antiguitat i d'altres problemes que pot tindre l'arbre causats per deficiències nutricionals o per altres plagues. En l'anàlisi per a identificar el dany causat per esta plaga, es va obtindre una taxa d'èxit del 92,5% en les imatges en color. No obstant això, no es va poder discriminar l'edat del dany. En les imatges hiperespectrals, l'èxit va ser del 100% en la detecció del dany i del 92% en la discriminació de l'edat. En quan a la discriminació de danys de T. urticae respecte a altres danys, en les imatges en color es va obtindre una taxa d'èxit del 100% en la discriminació de Phyllocnistis citrella en el revés dels fulls. Les deficiències de N no van poder discriminar-se correctament i les deficiències de Fe, Mn o Zn es van detectar encertadament en el 50% dels casos. En les imatges hiperespectrals, els danys per pogué P. citrella es van discriminar amb èxit en el 100% dels casos, tant en el feix com en el revés dels fulls. Les deficiències per N es van discriminar correctament en més del 65% dels casos també en ambdós costats del full. No obstant això, les deficiències de Fe, Mn o Zn no van poder ser discriminades correctament Les conclusions de esta Tesi Doctoral posen de manifest el gran potencial d'implementar estes tecnologies per a monitoritzar, optimitzar tasques i digitalitzar els processos en les labors dues a terme en els camps de cítrics, de manera que s'aconseguix augmentar l'eficiència, productivitat i la competitivitat en el sector., [EN] This PhD dissertation aims to generate knowledge and technology to develop mechanised and automated solutions to monitor processes, optimise tasks and increase the productivity of citrus crops and, therefore, the competitiveness of the citriculture sector. For this purpose, this thesis has focused on the development of technologies in some of the most important and costly operations in the citrus sector. To facilitate and optimise the harvesting of citrus fruits for the fresh market, improvements were implemented in a prototype of a self-propelled assistance platform. The research has focused on guaranteeing the operator safety, ensuring the quality of the harvested fruit and classifying it properly based on its quality by an artificial vision system in real-time. The functionality was evaluated in-field conditions and performance was assessed. The results showed that the assisted harvesting process with the platform was more efficient than traditional manual harvesting. A theoretical operation yield was obtained with the prototype, 17% lower than in conventional manual harvesting. Furthermore, in order to automatically generate citrus yield maps accessible for the farmer, a new digital tool was created as a dashboard, called CitrusYield. This tool is capable of obtaining maps showing the variability, using the information provided during the fruit inspection at harvest and the data obtained by the geolocation device, and also allowing to know the performance of the production at the intra-orchard level. The CitrusYield functionality was evaluated with data obtained by the prototype. The dashboard analysed the data and generated different maps georeferencing the information of the fruit with its harvesting point. Through these maps, the ability of CitrusYield to show the heterogeneity of production within the orchard was demonstrated. The production variability was also quantified in the tables and graphs generated by the tool. The indicators of fruit quality obtained by the artificial vision system and the productivity revealed the degree of effectiveness and efficiency of the harvesting process with the prototype. In the context of early citrus pests and diseases detection, the potential of colour and hyperspectral imaging, as a fast and automatic methods to detect the presence and the age of the damage caused by the Tetranychus urticae pest on citrus leaves, were investigated. Another goal was to discriminate this damage from that caused by other pests and from nutritional deficiencies. In the analysis of identifying the damage caused by T. urticae, a success rate of 92,5% was obtained in the colour images. However, the age of the damage could not be discriminated. In hyperspectral images, the success rate was 100% in damage detection and 92% in age discrimination. Regarding the discrimination of T. urticae damages from others, in the colour images, a success of 100% was obtained in the discrimination of Phyllocnistis citrella on the underside of the leaves. N deficiencies could not be correctly discriminated and Fe, Mn or Zn deficiencies were correctly detected in 50% of cases. In the hyperspectral images, P. citrella damage was successfully discriminated in 100% of cases, both on the upper and under sides of the leaves. N deficiencies were correctly discriminated in more than 65% of cases on both sides of the leaf. However, Fe, Mn or Zn deficiencies could not be correctly discriminated. The conclusions of this Thesis show the potential of implementing these technologies to monitor, optimize tasks and digitize agricultural processes in the operations usually done in citrus crops. Therefore, the efficiency, productivity and competitiveness of the sector can increase when these technologies are used., Esta Tesis Doctoral ha recibido una subvención para la formación de personal investigador en agroalimentación en los centros de investigación agraria y alimentaria INIA-CC.AA. (FPI-INIA CPD2016-0007, #42), otorgada por el Instituto Nacional de Investigaciones y Tecnología Agraria y Alimentaria, con el apoyo parcial de los Fondos FEDER 2014-2020. En esta Tesis Doctoral se han realizado investigaciones en el marco de varios proyectos de investigación: Aplicación de nuevas tecnologías para una estrategia integral de la recolección mecanizada de cítricos (CITRUSREC) (RTA2014-00025-C05-00).Subproyecto 1 centrado en el desarrollo y evaluación de una plataforma de asistencia a la recolección (RTA2014-00025-C05-01) Subproyecto 5 sobre la generación de herramientas de ayuda para la toma de decisiones (RTA2014-00025-C05-05) Desarrollos de ingeniería para el aseguramiento de una agricultura rentable, sostenible y competitiva del campo a la mesa (GVA-IVIA proyecto 51918) Grupo Operativo "Avances tecnológicos para la modernización y la sostenibilidad en la producción de cítricos (GO CITRUSTECH)".
ReDivia Repositorio Digital del Instituto Valenciano de Investigaciones Agrarias
Publicación Artículo científico (JournalArticle)

Automated Detection of Tetranychus urticae Koch in Citrus Leaves Based on Colour and VIS/NIR Hyperspectral Imaging

  • González-González, María G.
  • Blasco, José
  • Cubero, Sergio
  • Chueca, Patricia
etranychus urticae Koch is an important citrus pest that produces chlorotic spots on the leaves and scars on the fruit of affected trees. It is detected by visual inspection of the leaves. This work studies the potential of colour and hyperspectral imaging (400–1000 nm) under laboratory conditions as a fast and automatic method to detect the damage caused by this pest. The ability of a traditional vision system to differentiate this pest from others, such as Phyllocnistis citrella, and other leaf problems such as those caused by nutritional deficiencies, has been studied and compared with a more advanced hyperspectral system. To analyse the colour images, discriminant analysis has been used to classify the pixels as belonging to either a damaged or healthy leaves. In contrast, the hyperspectral images have been analysed using PLS DA. The rate of detection of the damage caused by T. urticae with colour images reached 92.5%, while leaves that did not present any damage were all correctly identified. Other problems such as damage by P. citrella were also correctly discriminated from T. urticae. Moreover, hyperspectral imaging allowed damage caused by T. urticae to be discriminated from healthy leaves and to distinguish between recent and mature leaves, which indicates whether it is a recent or an older infestation. Furthermore, good results were achieved in the discrimination between damage caused by T. urticae, P. citrella, and nutritional deficiencies.
ReDivia Repositorio Digital del Instituto Valenciano de Investigaciones Agrarias
Publicación Artículo científico (JournalArticle)

Volume Rate Adjustment for Pesticide Applications against Aonidiella aurantii in Citrus: Validation of CitrusVol in the Growers’ Practice

  • Fonte, Alberto
  • Garcerá, Cruz
  • Tena, Alejandro
  • Chueca, Patricia
Aonidiella aurantii is one of the most damaging armored scales in citrus crops worldwide. To control this pest, high water volume rates are conventionally used. In order to rationalize the pesticide applications in citrus, IVIA developed CitrusVol, a tool that recommends the optimal volume rate based on the vegetation, the pest or disease and the active ingredient. In this study the objectives were: (I) validate CitrusVol as a tool to adjust the spray volume to control A. aurantii and (II) quantify its environmental and economical advantages. For this, the spray volume adjusted with CitrusVol was compared with the one conventionally used by farmers in 18 applications in seven orchards during two years. The following parameters were evaluated: (I) spray distribution in the canopy, (II) A. aurantii males trapped per day, and (III) number of scales per fruit at harvest. CitrusVol reduced the spray volume and the amount of pesticide by 35% on average. Despite this reduction, a satisfactory spray distribution was achieved, and the volume was found to control the pest in a comparable way to the conventional volume. Moreover, CitrusVol saved per application and on average 31.25 h/100 ha of spray operating time, 241.83 L/100 ha of fuel consumption and consequently, the reduction of emissions of CO2 was 631.18 kg/100 ha. Therefore, CitrusVol allows for efficient, low-input and low-impact pesticide applications.
ReDivia Repositorio Digital del Instituto Valenciano de Investigaciones Agrarias
Publicación Artículo científico (JournalArticle)

Detection of Invisible Damages in ‘Rojo Brillante’ Persimmon Fruit at Different Stages Using Hyperspectral Imaging and Chemometrics

  • Munera, Sandra
  • Rodríguez-Ortega, Alejandro
  • Aleixos, Nuria
  • Cubero, Sergio
  • Gómez-Sanchís, Juan
  • Blasco, José
The main cause of flesh browning in ‘Rojo Brillante’ persimmon fruit is mechanical damage caused during harvesting and packing. Innovation and research on nondestructive techniques to detect this phenomenon in the packing lines are necessary because this type of alteration is often only seen when the final consumer peels the fruit. In this work, we have studied the application of hyperspectral imaging in the range of 450–1040 nm to detect mechanical damage without any external symptoms. The fruit was damaged in a controlled manner. Later, images were acquired before and at 0, 1, 2 and 3 days after damage induction. First, the spectral data captured from the images were analysed through an algorithm based on principal component analysis (PCA). The aim was to automatically separate intact and damaged fruit, and to detect the damage in the PC images when present. With this algorithm, 90.0% of intact fruit and 90.8% of damaged fruit were correctly detected. A model based on partial least squares—discriminant analysis (PLS-DA), was later calibrated using the mean spectrum of the pixels detected as damaged, to determine the moment when the fruit was damaged. The model differentiated fruit corresponding correctly to 0, 1, 2 and 3 days after damage induction, achieving a total accuracy of 99.4%.
ReDivia Repositorio Digital del Instituto Valenciano de Investigaciones Agrarias
Publicación

Application of deep convolutional neural networks for the detection of anthracnose in olives using VIS/NIR hyperspectral images

  • Fazari, Antonio
  • Pellicer-Valero, Óscar
  • Gómez-Sanchís, Juan
  • Bernardi, Bruno
  • Cubero, Sergio
  • Benalia, Souraya
  • Zimbalatti, Giuseppe
  • Blasco, José
Anthracnose is one of the primary diseases that affect olive production before and after harvest, causing severe damage and economic losses. The objective of this work is to detect this disease in the early stages, using hyperspectral images and advanced modelling techniques of Deep Learning (DL) and convolutional neural networks (CNN). The olives were artificially inoculated with the fungus. Hyperspectral images (450–1050 nm) of each olive were acquired until visual symptoms of the disease were observed, in some cases up to 9 days. The olives were classified into two classes: control, inoculated with water, and fungi composed of olives inoculated with the fungus. The ResNet101 architecture was chosen and adapted to process 61-band hyperspectral images with only two classes. The result showed that the applied model is very effective in detecting infected olives since the sensitivity of the method was very high from the beginning (85% on day 3 and 100% onwards). From a commercial point of view, these results align with the need to detect the maximum number of infected fruits.
ReDivia Repositorio Digital del Instituto Valenciano de Investigaciones Agrarias
Publicación Artículo científico (JournalArticle)

Fusion of Different Image Sources for Improved Monitoring of Agricultural Plots

  • Moltó, Enrique
In the Valencian Community, the applications of precision agriculture in multiannual woody crops with high added value (fruit trees, olive trees, almond trees, vineyards, etc.) are of priority interest. In these plots, canopies do not fully cover the soil and the planting frames are incompatible with the Resolution of Sentinel 2. The present work proposes a procedure for the fusion of images with different temporal and spatial resolutions and with different degrees of spectral quality. It uses images from the Sentinel 2 mission (low resolution, high spectral quality, high temporal resolution), orthophotos (high resolution, low temporal resolution) and images obtained with drones (very high spatial resolution, low temporal resolution). The procedure is applied to generate time series of synthetic RGI images (red, green, infrared) with the same high resolution of orthophotos and drone images, in which gray levels are reassigned from the combination of their own RGI bands and the values of the B3, B4 and B8 bands of Sentinel 2. Two practical examples of application are also described. The first shows the NDVI images that can be generated after the process of merging two RGI Sentinel 2 images obtained on two specific dates. It is observed how, after the merging, different NDVI values can be assigned to the soil and vegetation, which allows them to be distinguished (contrary to the original Sentinel 2 images). The second example shows how graphs can be generated to describe the evolution throughout the vegetative cycle of the estimated values of three spectral indices (NDVI, GNDVI, GCI) on a point in the image corresponding to soil and on another assigned to vegetation. The robustness of the proposed algorithm has been validated by using image similarity metrics.
ReDivia Repositorio Digital del Instituto Valenciano de Investigaciones Agrarias
Publicación Artículo científico (JournalArticle)

Effect of the Airblast Settings on the Vertical Spray Profile: Implementation on an On-Line Decision Aid for Citrus Treatments

  • Garcerá, Cruz
  • Moltó, Enrique
  • Izquierdo-Sanz, Héctor
  • Balsari, Paolo
  • Marucco, Paolo
  • Grella, Marco
  • Gioelli, Fabrizio
  • Chueca, Patricia
Airblast sprayers are widely used for the application of plant protection products (PPP) in citrus. Adaptation of the vertical distribution of the spray cloud to the canopy (density, shape and size), is essential to deposit an adequate amount of PPP on the target and to reduce losses (drift, runoff). Vertical spray profiles of three air-assisted axial fan hydraulic sprayers with different configurations and settings were obtained to evaluate the effect of these settings on the vertical spray profile. From the analysis of the empirical results, the impact of operational settings (nozzle, air volume and flow rate) on treatment efficiency is assessed. The empirical database generated in this work has been employed to feed the Citrus VESPA model, a highly intuitive, web-based decision aid tool that helps farmers to easily estimate the vertical spray profiles generated by their particular sprayers and settings and how these influence deposition and potential drift. The tool can also be used to determine the effect and importance of adequately selecting, orienting and opening/closing nozzles and optimizing volume application rate and fan speed, in order to adjust the application to the actual vegetation, with the aim of saving resources and reducing risks to humans and the environment.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrogels for Cartilage Regeneration, from Polysaccharides to Hybrids

  • Sánchez-Téllez, Daniela Anahí
  • Téllez-Jurado, Lucía
  • Rodríguez-Lorenzo, Luis M.
The aims of this paper are: (1) to review the current state of the art in the field of cartilage substitution and regeneration; (2) to examine the patented biomaterials being used in preclinical and clinical stages; (3) to explore the potential of polymeric hydrogels for these applications and the reasons that hinder their clinical success. The studies about hydrogels used as potential biomaterials selected for this review are divided into the two major trends in tissue engineering: (1) the use of cell-free biomaterials; and (2) the use of cell seeded biomaterials. Preparation techniques and resulting hydrogel properties are also reviewed. More recent proposals, based on the combination of different polymers and the hybridization process to improve the properties of these materials, are also reviewed. The combination of elements such as scaffolds (cellular solids), matrices (hydrogel-based), growth factors and mechanical stimuli is needed to optimize properties of the required materials in order to facilitate tissue formation, cartilage regeneration and final clinical application. Polymer combinations and hybrids are the most promising materials for this application. Hybrid scaffolds may maximize cell growth and local tissue integration by forming cartilage-like tissue with biomimetic features, This work was supported by SIP-IPN 20170510 Project (Mexico), DGICYT Project, MAT2014-51918-C2-I-R (Spain), (CONACYT/CSIC)-EMHE program through project No. MHE200011 (Mexico-Spain). DA Sánchez-Téllez also acknowledges CONACYT (Mexico) for the scholarship given. The authors acknowledge Stephanie Cisneros-Téllez for helping them in the digitalization of Figures 1, 4 and 8., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biocompatible and bioadhesive low molecular weight polymers containing long-arm catechol-functionalized methacrylate

  • Puertas-Bartolomé, María
  • Fernández-Gutiérrez, Mar
  • García-Fernández, Luis
  • Vázquez-Lasa, Blanca
  • San Román, Julio
Excellent adherence properties of blue mussels have been attributed to a catechol-containing amino acid, L-3,4-dihydroxyphenylalanine. This natural form of adhesion has been a source to develop bioadhesive polymers that adhere to biological interfaces. In this study, we describe a bioinspired approach for preparing bioadhesive and biocompatible materials based on synthetic low molecular weight copolymers of a flexible catechol-functionalized methacrylate (CEMA) and N-vinylcaprolactam. Copolymers with CEMA contents in the range 0.9–13.5 mol% were obtained by radical copolymerization. These systems show good biocompatibility and provide good antioxidant behavior and anti-inflammatory activity. Likewise, hydrogels prepared by mixture of a selected copolymer with gelatin possess good bone bioadhesive properties. These findings show that copolymer composition can be used as a tool for the preparation of biomedical systems with tunable properties and great potential for the development of drug delivery systems and bioactive gels that can be applied in tissue regeneration processes., This work was supported by CIBER-BBN (Spain) and the Spanish Ministry of Economy and Competitiveness [project MAT2014-51918- C2-1-R and M. Puertas-Bartolomé scholarship, Peer reviewed, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

pH-sensitive polymeric nanoparticles with antioxidant and anti-inflammatory properties against cisplatin-induced hearing loss

  • Martín-Saldaña, Sergio
  • Palao-Suay, Raquel
  • Aguilar, María Rosa
  • García-Fernández, Luis
  • Arévalo, Humberto
  • Trinidad, Almudena
  • Ramírez-Camacho, Rafael
  • San Román, Julio
Polymeric nanoparticles (NPs) based on smart synthetic amphiphilic copolymers are used to transport and controlled release dexamethasone in the inner ear to protect against the ototoxic effect of cisplatin. The NPs were based on a mixture of two pseudo-block polymer drugs obtained by free radical polymerization: poly(VI-co-HEI) and poly(VP-co-MVE) or poly(VP-co-MTOS), being VI 1-vinylimidazole, VP N-vinylpyrrolidone, and HEI, MVE and MTOS the methacrylic derivatives of ibuprofen, α-tocopherol and α-tocopheryl succinate, respectively. The NPs were obtained by nanoprecipitation with appropriate hydrodynamic properties, and isoelectric points that matched the pH of inflamed tissue. The NPs were tested both in vitro (using HEI-OC1 cells) and in vivo (using a murine model) with good results. Although the concentration of dexamethasone administered in the NPs is around two orders of magnitude lower that the conventional treatment for intratympanic administration, the NPs protected from the cytotoxic effect of cisplatin when the combination of the appropriate properties in terms of size, zeta potential, encapsulation efficiency and isoelectric point were achieved. To the best of our knowledge this is the first time that pH sensitive NPs are used to protect from cisplatin-induced hearing loss by intratympanic administration., This work was funded by the Spanish Ministry of Economy and Competitiveness (MAT2014-51918-C2-1-R) and CIBER BBN-ECO Foundation project (NANOVIT)., Peer reviewed, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Contribution of bioactive hyaluronic acid and gelatin to regenerative medicine. Methodologies of gels preparation and advanced applications

  • Mora-Boza, Ana
  • Puertas-Bartolomé, María
  • Vázquez-Lasa, Blanca
  • San Román, Julio
  • Pérez-Caballer, Antonio
  • Olmeda-Lozano, Marta
An overview of the most relevant crosslinking processes and agents that are being developed for regenerative medicine, including different hydrogel modifications as well as several interesting and advanced applications. The functionality and reactivity of polysaccharides and in particular hyaluronic acid in combination with proteins like gelatin, collagen and many others offer very interesting opportunities for the new trends in regenerative medicine. The biomimetic approaches for the application in regenerative processes and tissue engineering have enormous possibilities because of the excellent response of these biomimetic materials and their bioactive and biodegradable character in the human body. These characteristics together with the possibility of application by minimally invasive surgery offer very interesting applications in regeneration of tissues and organs, as well as in targeting and releasing of bioactive compounds applications as drug delivery systems. In addition, the growing of clinical applications of these macromolecular components as assemblies opens new and advanced opportunities in regenerative medicine and drug delivery fields., Authors thank CIBER-BBN, Spain and the Spanish Ministry of Economy and Competitivity (project MAT2014-51918-C2-1-R and M. Puertas-Bartolomé scholarship) and “la Caixa” Foundation (A. Mora-Boza scholarship) for supporting this work, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bioactive and bioadhesive catechol conjugated polymers for tissue regeneration

  • Puertas-Bartolomé, María
  • Vázquez-Lasa, Blanca
  • San Román, Julio
The effective treatment of chronic wounds constitutes one of the most common worldwide healthcare problem due to the presence of high levels of proteases, free radicals and exudates in the wound, which constantly activate the inflammatory system, avoiding tissue regeneration. In this study, we describe a multifunctional bioactive and resorbable membrane with in-built antioxidant agent catechol for the continuous quenching of free radicals as well as to control inflammatory response, helping to promote the wound-healing process. This natural polyphenol (catechol) is the key molecule responsible for the mechanism of adhesion of mussels providing also the functionalized polymer with bioadhesion in the moist environment of the human body. To reach that goal, synthesized statistical copolymers of N-vinylcaprolactam (V) and 2-hydroxyethyl methacrylate (H) have been conjugated with catechol bearing hydrocaffeic acid (HCA) molecules with high yields. The system has demonstrated good biocompatibility, a sustained antioxidant response, an anti-inflammatory effect, an ultraviolet (UV) screen, and bioadhesion to porcine skin, all of these been key features in the wound-healing process. Therefore, these novel mussel-inspired materials have an enormous potential for application and can act very positively, favoring and promoting the healing effect in chronic wounds., This research was funded by CIBER-BBN, Spain and the Spanish Ministry of Economy and Competitivity (project MAT2014-51918-C2-1-R and María Puertas-Bartolomé’s scholarship, and project MAT2017-84277-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of advanced biantibiotic loaded bone cement spacers for arthroplasty associated infections

  • Parra, Francisco
  • González-Gómez, Álvaro
  • Fernández-Gutiérrez, Mar
  • Parra, J.
  • García-García, J.
  • Azuara, G.
  • Torre, B. de la
  • Buján, J.
  • Ibarra, B.
  • Duocastella Codina, Luis
  • Molina-Crisol, M.
  • Vázquez-Lasa, Blanca
  • San Román, Julio
The incidence increase of infections in patients with hip or knee implants with resistant pathogens (mainly some S. coagulase-negative and gram positive bacteria) demands advanced antibiotic loaded formulations. In this paper, we report the design of new biantibiotic acrylic bone cements for in situ delivery. They include a last generation antibiotic (daptomycin or linezolid) in combination with vancomycin and are performed based on a novel modification of the Palacos R acrylic bone cement, which is based on two components, a liquid (methyl methacrylate) and a solid (polymeric phase). Hence, the solid component of the experimental formulations include 45 wt% of microparticles of poly(D,L-lactic-co-glycolic) acid, 55 wt% of poly(methyl methacrylate) beads and supplements (10 wt-% each) of antibiotics. These formulations provide a selective and excellent control of the local release of antibiotics during a long time period (up to 2 months), avoiding systemic dissemination. The antimicrobial activity of the advanced spacers tested against S. aureus shows that single doses would be enough for the control of the infection. In vitro biocompatibility of cements on human osteoblasts is ensured. This paper is mainly focused on the preparation and characterization of cements and the studies of elution kinetics and bactericidal effects. Developed formulations are proposed as spacers for the treatment of infected arthroplasties, but also, they could be applied in other antibiotic devices to treat relevant bone-related infection diseases., Authors thank to The Spanish Ministry of Economy and Competitivity (project MAT2014-51918-C2-1-R) and Spanish SECOT Foundation (Project 2015) for financial support, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polylactic-co-glycolic acid microspheres added to fixative cements and its role on bone infected architecture

  • Ibarra, Blanca
  • García-García, J.
  • Azuara, G.
  • Vázquez-Lasa, Blanca
  • Ortega, Miguel Ángel
  • Asúnsolo, Ángel
  • San Román, Julio
  • Buján, J.
  • García-Honduvilla, N.
  • Torre, B. de la
Joint prostheses are an essential element to improve quality of life. However, prostheses may fail due to several factors, including the most frequent cause, Staphylococcus aureus infection. The identification of new fixing bone cements with less reactivity on bone tissue and an adequate response to infection remains a primary challenge. The aim of this study is to evaluate the response of bone tissue in rabbits after introduction of a hydroxyapatite-coated titanium rod with a commercial fixative cement (Palacos®) compared to a modified experimental cement (EC) containing polylactic-co-glycolic acid (PLGA) microspheres in the presence or absence of contaminating germs. This study used 20 New Zealand rabbits which were divided into four groups (n = 5) depending on the presence or absence of S. aureus and the use of commercial (Palacos®) or EC. A histological method, based on bone architecture damage, was proposed to evaluate from 1 to 9 the histological results and the response of the infected tissue. The macrophage response was also evaluated using monoclonal antibody RAM-11. The study showed better bone conservation with the use of EC with PLGA microspheres against the Palacos® commercial cement, including the noncontaminated and contaminated groups. © 2019 The Authors. Journal of Biomedical Materials Research Part B: Applied Biomaterials published by Wiley Periodicals, Inc. J Biomed Mater Res Part B: 00B: 000–000, 2019., SECOT (Spanish Society of Orthopedic Surgery and Traumatology); contract grant number: 2016/0055 MINECO (SpanishMinistry of Economy and Competitiveness); contract grant numbers:MAT2014-51918-C2-1-R,MAT-2017-84277-R MITIC-CM(Community of Madrid); contract grant number: B2017/BMD-3804, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bioadhesive functional hydrogels: Controlled release of catechol species with antioxidant and antiinflammatory behavior

  • Puertas-Bartolomé, María
  • Benito-Garzón, Lorena
  • Fung, S.
  • Kohn, J.
  • Vázquez-Lasa, Blanca
  • San Román, Julio
Chronic wounds are particularly difficult to heal and constitute an important global health care problem. Some key factors that make chronic wounds challenging to heal are attributed to the incessant release of free radicals, which activate the inflammatory system and impair the repair of the wound. Intrinsic characteristics of hydrogels are beneficial for wound healing, but the effective control of free radical levels in the wound and subsequent inflammation is still a challenge. Catechol, the key molecule responsible for the mechanism of adhesion of mussels, has been proven to be an excellent radical scavenger and anti-inflammatory agent. Our approach in this work lies in the preparation of a hybrid system combining the beneficial properties of hydrogels and catechol for its application as a bioactive wound dressing to assist in the treatment of chronic wounds. The hydrogel backbone is obtained through a self-covalent crosslinking between chitosan (Ch) and oxidized hyaluronic acid (HAox) in the presence of a synthetic catechol terpolymer, which is subsequently coordinated to Fe to obtain an interpenetrated polymer network (IPN). The structural analysis, catechol release profiles, in vitro biological behavior and in vivo performance of the IPN are analyzed and compared with the semi-IPN (without Fe) and the Ch/HAox crosslinked hydrogels as controls. Catechol-containing hydrogels present high tissue adhesion strength under wet conditions, support growth, migration and proliferation of hBMSCs, protect cells against oxidative stress damage induce by ROS, and promote down-regulation of the pro-inflammatory cytokine IL-1β. Furthermore, in vivo experiments reveal their biocompatibility and stability, and histological studies indicate normal inflammatory responses and faster vascularization, highlighting the performance of the IPN system. The novel IPN design also allows for the in situ controlled and sustained delivery of catechol. Therefore, the developed IPN is a suitable ECM-mimic platform with high cell affinity and bioactive functionalities that, together with the controlled catechol release, will enhance the tissue regeneration process and has a great potential for its application as wound dressing., Authors thank CIBER-BBN (Spain); the Spanish Ministry of Economy and Competitiveness (project MAT2014-51918-C2-1-R, M. Puertas- Bartolomé scholarship and project MAT2017-84277-R); and International Summer Exchange for supporting this work. The authors thank Rosana Ramírez of ICTP-CSIC, Spain, for assistance in the biological culture assays., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D Printing of a Reactive Hydrogel Bio-Ink Using a Static Mixing Tool

  • Puertas-Bartolomé, María
  • Włodarczyk-Biegun, Małgorzata K.
  • Campo, Aránzazu del
  • Vázquez-Lasa, Blanca
  • San Román, Julio
© 2020 by the authors., Hydrogel-based bio-inks have recently attracted more attention for 3D printing applications in tissue engineering due to their remarkable intrinsic properties, such as a cell supporting environment. However, their usually weak mechanical properties lead to poor printability and low stability of the obtained structures. To obtain good shape fidelity, current approaches based on extrusion printing use high viscosity solutions, which can compromise cell viability. This paper presents a novel bio-printing methodology based on a dual-syringe system with a static mixing tool that allows in situ crosslinking of a two-component hydrogel-based ink in the presence of living cells. The reactive hydrogel system consists of carboxymethyl chitosan (CMCh) and partially oxidized hyaluronic acid (HAox) that undergo fast self-covalent crosslinking via Schiff base formation. This new approach allows us to use low viscosity solutions since in situ gelation provides the appropriate structural integrity to maintain the printed shape. The proposed bio-ink formulation was optimized to match crosslinking kinetics with the printing process and multi-layered 3D bio-printed scaffolds were successfully obtained. Printed scaffolds showed moderate swelling, good biocompatibility with embedded cells, and were mechanically stable after 14 days of the cell culture. We envision that this straightforward, powerful, and generalizable printing approach can be used for a wide range of materials, growth factors, or cell types, to be employed for soft tissue regeneration., This research was funded by CIBER-BBN, Spain and the Spanish Ministry of Economy and Competitivity (project MAT2017-84277-R and M. Puertas-Bartolomé scholarship BES-2015-075161). B. Vázquez-Lasa and J. San Román are members of the SusPlast platform (Interdisciplinary Platform for Sustainable Plastics towards a Circular Economy) from the Spanish National Research Council (CSIC)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Micro-structured 3D-electrospun scaffolds of biodegradable block copolymers for soft tissue regeneration

  • Fabbri, M.
  • García-Fernández, Luis
  • Vázquez-Lasa, Blanca
  • Soccio, M.
  • Gamberini, R.
  • Rimini, B.
  • Munari, A.
  • San Román, Julio
The present article describes the application of a poly(ethylene terephthalate) mesh as template for the preparation of micro-structured fibres mat by electrospinning of biodegradable triblock copolymers based on polylactic acid and poly(butylene succinate/azelate) random copolymer. These copolymers present and excellent controlled biodegradation process in physiological conditions, with interesting applications in targeting and controlled release of different drugs. After the application of the poly(ethylene terephthalate) mesh in the electrospinning process, the detachment of the template provides a specific oriented microfibres mat, that affect to the adhesion and proliferation of cell seeded on the networks. In addition, the microfibres mats were loaded with dexamethasone as anti-inflammatory drug. The release of the drug takes place in a controlled relative short period due to the formation of drug crystals on the surface of the fibres during the electrospinning process. This issue can be restrained by acting on the triblock copolymer composition, improving the drug-polymer compatibility. Copolymerization also allows the modulation of the biodegradation rate. The biodegradable scaffolds under investigation can be therefore considered very promising for regenerative medicine and soft tissue engineering., L.García-Fernández, B. Vázquez-Lasa and J. San Roman thank CIBER-BBN and the Spanish Ministry of Economy and Competitiveness [grant number MAT2014-51918-C2-1-R] for supporting this work.