Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 21
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Shear strength of concrete beams using stay-in-place flexible formworks with integrated transverse textile reinforcement

  • Lee, Minu
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] This study investigates the fabrication and the structural performance of concrete beams using weft-knitted tubular fabrics as stay-in-place formworks with integrated textile reinforcement. The use of non-corrosive high-strength textile materials for flexible formworks offers great potential for efficient construction processes and a bespoke design of material-efficient concrete structures. To this end, an experimental campaign consisting of ten three-point bending tests on beams with rectangular cross-sections made with flexible stay-in-place formworks was conducted, where aramid rovings were integrated within the textile as transverse reinforcement to withstand the shear forces while the longitudinal reinforcement consisted of conventional deformed steel bars. The use of digital image correlation measurements and distributed fibre optical sensing allowed the refined analysis of the deformations, including the strains in the textile reinforcement and the estimation of the crack kinematics, which were used to assess various contributions from the reinforcement and the concrete to the shear strength in the governing crack. The amount of textile reinforcement proved to be a decisive parameter in increasing the shear strength, although the full tensile capacity of the rovings could not be exploited due to the lack of ductility in the material behaviour. The thorough consideration of the shear transfer mechanisms revealed a strong dependence of the concrete contribution, specifically aggregate interlock and the formation of a direct strut, on the crack patterns. The combination of the brittle aramid rovings as shear reinforcement and conventional steel reinforcing bars in the tension chord provided a large deformation capacity if the shear reinforcement was able to sustain the load until a bending failure was reached., This research is supported by the National Centre for Competence in Research in Digital Fabrication, funded by the Swiss National Science Foundation (project number 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental exploration of digitally fabricated connections for structural concrete

  • Bichof, Patrick
  • Burger, Joris
  • Gebhard, Lukas
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Connections are a persistent challenge for traditional reinforced concrete construction and even more for digital fabrication with concrete (DFC). The latter, on the other hand, opens up new possibilities for producing connections with tailored geometries and surface roughness. Based on the findings of an exploratory, experimental campaign, this paper discusses the design, fabrication and structural testing of digitally fabricated joints using the DFC technology Eggshell to 3D print the formwork for joint surfaces in an additive manufacturing process. The programme includes (i) unreinforced and reinforced construction joints whose joint surface texture was varied to control the roughness and (ii) digitally fabricated dry keyed joints with varying geometry. Both, the construction joints as well as the dry keyed joints, were produced using set-on-demand concrete with a relatively small maximum aggregate size of 0 to 4 mm ¿ i.e., strictly speaking, mortar rather than concrete ¿ as typically applied in DFC. The experimental campaign included thorough instrumentation: a 3D scan of the joint surface before testing and high-resolution digital image correlation (DIC) combined with distributed fibre optical sensing (DFOS) during testing. The deviations from the targeted surface geometry, determined with 3D scans, were below 2 mm, with a standard deviation between 0.4 mm and 0.7 mm for keyed joints. The high-resolution DIC allowed measuring the compressive strains locally at (i) the corrugation of unreinforced or reinforced construction joints and (ii) the key chamfer of dry joints and, hence, studying strain variations over the height of the joints and the efficiency of different keys with varying dimensions. Finally, the shear transfer capacity, evaluated in a push-off test setup, showed that all digitally fabricated joints met or even outperformed the requirements defined in pertinent design codes despite the smaller aggregate size., The authors thank Tena Galkovski, Nicola Gehri, Armin Bratschi, Siro Gianinazzi, and the IBK Structural Lab personnel for their support in executing and evaluating the experiments presented in this paper. Furthermore, the authors thank Robert Presl (Institute of Geodesy and Photogrammetry, Department of Civil, Environmental and Geomatic Engineering, ETH Zurich) for his support in performing and evaluating the joint surface scans. Finally, the authors thank Pietro De Zanet for his support in creating Fig. 4, Fig. C.6 and Fig. C.7. This research project was supported by the NCCR in Digital Fabrication and funded by the SNSF number 51NF40 141853) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structural design and testing of material optimized ribbed RC slabs with 3D printed formwork

  • Huber, Tobias
  • Burger, Joris
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Most of the concrete volume in multistorey buildings is cast in solid slabs, which are frequently flat slabs supported on columns. By using two-way spanning ribbed slabs, concrete consumption could be significantly reduced. However, due to the high costs associated with formwork, such a complex rib configuration is rarely used nowadays. With the advent of technologies for automated formwork fabrication, the material-saving potential inherent in this structural system could again be exploited. This paper investigates the feasibility of material-efficient ribbed concrete slabs on a building scale using conventional concrete and steel reinforcing bars cast inside a three-dimensionalprinted plastic-based formwork. To that end, the code-compliant design of ribbed slabs is first discussed, followed by the introduction of a concept for an automated design-to-production workflow. The sustainability of this slab system is compared to a solution using conventional formwork in a case study consisting of a multibay office building with slabs spanning 8 m in both directions, revealing that ribbed slabs use 40% less concrete than solid slabs. Several representative structural elements of the case study (ribs, slab-column transition) were produced at full-scale and tested until failure to investigate the feasibility of production and structural performance. Three T-beams with various rib shapes (straight, kinked with diaphragms, curved) were tested in a threepoint bending configuration, showing a ductile behavior with longitudinal reinforcement yielding and indicating the relevance of torsional effects in curved ribs. Punching tests on two slab-column connections (ribbed, solid) revealed that the optimized ribbed slab could prevent brittle punching failures and achieve an ultimate load 105% higher than the solid reference slab. All specimens' load-bearing behavior could be predicted using established design formulas, showing the feasibility of producing code-compliant ribbed slabs with the applied technology., ETH Zürich Foundation; Geberit; Siemens; Swiss National Science Foundation's NCCR Digital Fabrication, Grant/Award Number: 51NF40-141853
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Towards efficient concrete structures with ultra-thin 3D printed formwork: exploring reinforcement strategies and optimisation

  • Gebhard, Lukas
  • Burger, Joris
  • Lloret-Fritschi, Ena
  • Gramazio, Fabio
  • Kohler, Matthias
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] The Eggshell fabrication process combines the 3D printing of formwork with the simultaneous casting of a fast-hardening concrete. One limiting factor to reaching mass-market adoption is a suitable reinforcing strategy. In this study, a reinforcement strategy combining steel reinforcing bars with steel fibres is explored. A series of eight beams were produced using the Eggshell process or conventionally cast. The longitudinal reinforcement was provided by two reinforcing bars, and two types of fibres, either mixed with the concrete or placed and aligned between the cast concrete layers, were used as shear reinforcement. The results showed that combining conventional longitudinal reinforcement and fibres as shear reinforcement is a suitable strategy. These findings were applied to fabricate an optimised beam with a volume reduction of almost 50%. The structural performance of this beam was similar to the beam with a rectangular crosssection with the same reinforcement strategy showing the potential of Eggshell in combination with an innovative reinforcement strategy to produce material-efficient structural concrete elements., This work was funded by the Swiss National Science Foundation, within the National Centre for Competence in Research in Digital Fabrication (project number 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thin-walled concrete beams with stay-in-place flexible formworks and integrated textile shear reinforcement

  • Lee, Minu
  • Popescu, Mariana
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Thin-walled textile-reinforced concrete beams have recently emerged as a promising approach for material-efficient design. However, the increased complexity of the formwork is a major challenge in implementing such elements for broader use in the construction industry. This study presents a novel type of stay-in-place flexible formworks with integrated textile reinforcement. The use of weft-knitted textiles allows the integration of continuous high-strength rovings as shear reinforcement and the introduction of spatial features within the fabric to guide bending-active rods to shape the complex cross-section geometry. The manufacturing procedure and the structural performance were investigated in an experimental campaign consisting of four concrete beams with I-profile cross sections tested in three-point bending, where aramid rovings were used for the shear and conventional deformed steel bars for the flexural reinforcement. The transverse reinforcement ratio proved to be essential in increasing the shear strength. Thereby, the use of digital image correlation measurements of the surface deformations allowed the direct assessment of the strains and, thus, the mechanical activation of the textile reinforcement. The full tensile capacity of all the aramid rovings crossing the governing crack could not be exploited due to the brittle material behavior, resulting in a progressive failure once the first roving reached its tensile strength. Compatibility-based stress fields were used to predict the load-deformation and failure behavior of the tested beams, which resulted in an excellent agreement of the ultimate loads and failure modes obtained from the model with the observations and results from the experiments., Swiss National Science Foundation, Grant/Award Number: 51NF40-141853
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Eggshell: Ultra-Thin Three-Dimensional Printed Formwork for Concrete Structures

  • Burger, Joris
  • Lloret-Fritschi, Ena
  • Scotto, Fabio
  • Demoulin, Thibault
  • Gebhard, Lukas
  • Gramazio, Fabio
  • Kohler, Matthias
  • Flatt, Robert J.
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Concrete is a material favored by architects and builders alike due to its high structural strength and its ability to take almost any form. However, to shape concrete structures, heavy-duty formwork is usually necessary to support the fresh concrete while curing. To expand geometrical freedom, three-dimensional (3D) printed concrete formwork has emerged as a field of research. This article presents one possible application, a novel fabrication process that combines large-scale robotic fused deposition modeling 3D printing with simultaneous casting of a fast-hardening, set-on-demand concrete. This fabrication process, known as ``Eggshell,¿¿ enables the production of nonstandard concrete structures in a material-efficient process. By casting a fast-hardening concrete in a continuous process, lateral pressure exerted by the fresh concrete is kept to a minimum. In this way, a 1.5-mm-thin thermoplastic shell can be used as a formwork, without any additional support. Geometries of different scales are tested in this article to evaluate the feasibility of the Eggshell fabrication process in an architectural context. An array of printing materials are also tested, and several different reinforcement concepts are analyzed. The findings are used to produce a full-scale architectural demonstrator project. This article shows that a wide range of concrete geometries can be produced in a material-efficient fabrication process, paving the way toward mass customization and structural optimization within concrete architecture., This research was supported by the NCCR Digital Fabrication, funded by the Swiss National Science Foundation (NCCR Digital Fabrication Agreement no. 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of the tension chord in the flexural response of concrete elements: Methodology and application to weft-knitted textile reinforcement

  • Lee, Minu
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] The use of high-strength fibrous materials offers great potential to serve as the main reinforcement in the flexural response of lightweight concrete structures. Specifically, weft-knitted textile reinforcement allows creating complex geometries (i.e. doubly curved or folded) and introducing straight inlays as well as spatial features such as ribs within the fabric to enhance the bond conditions between the reinforcement and the concrete. While the evaluation of uniaxial tension tests to characterise the mechanical behaviour is usually straightforward, the vast majority of bending tests of textile reinforced concrete elements in the literature are limited to load¿displacement data, which does not give direct information on the mechanical behaviour and makes it difficult to compare specimens with different geometries or reinforcement contents. This study presents a methodology based on digital image correlation measurements to directly assess the response in the tension chord of reinforced concrete beams in four-point bending. This methodology was applied and validated in an experimental campaign consisting of 16 bending tests with weft-knitted textile reinforcement. Various fibre materials, coating types and specimen geometries were tested, and the results were compared to corresponding uniaxial tension tests with the same type of reinforcement, generally showing a good agreement in the load-deformation behaviour and the crack kinematics. However, the textile reinforcement could not be utilised to the tensile strength obtained in uniaxial tension since all bending beams failed prematurely either in a combined bending-shear type failure (for most of the cement paste-coated textiles) or due to the delamination of the textile within a shear crack (for all epoxy-coated textiles). The Tension Chord Model with an assumed constant bond-slip relationship and an equivalent reinforcement ratio in bending yielded a good prediction of the stress¿strain relationship, the tension stiffening effect, the crack widths and spacing., The authors gratefully acknowledge Dr. Mariana Popescu from Block Research Group (ETHZ) and Dr. Lex Reiter from the Chair of Physical Chemistry of Building Materials (ETHZ) for contributing their technical and practical expertise, as well as the students Nathalie Chiaverio, Salome Geiser and Caterina Rovati for their valuable support during preparation and testing of the specimens. This research is supported by the National Centre for Competence in Research in Digital Fabrication, funded by the Swiss National Science Foundation (project number 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of short glass fibres and spatial features on the mechanical behaviour of weft-knitted textile reinforced concrete elements in bending

  • Lee, Minu
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Weft-knitted textiles made from high-strength fibrous materials offer great potential for use as a flexible stay-inplace formwork and reinforcement system since they allow creating complex geometries (i.e. doubly curved or folded) and introducing spatial features such as ribs within the fabric. However, the closed surface of the textile and its placement at the bottom edge of the concrete element present major challenges regarding bond, which may lead to premature failure due to delamination of the reinforcement initiated by a substantial opening of a governing crack. This study investigates the influence of short integral glass fibres and spatial bond ribs on the mechanical behaviour of weft-knitted textile reinforced concrete elements subjected to bending and their potential to increase the shear resistance. To this end, an experimental campaign consisting of 14 four-pointbending tests was conducted, where the specimens were examined regarding their load-deformation behaviour, crack kinematics and failure modes. The contribution of the short glass fibres to the load-bearing mechanism was estimated with Pfyl¿s fibre engagement model, based on the material characterisation results from prism tests on fibre reinforced concrete members. The Tension Chord Model was used to predict the stress-strain relationship of the reinforcement and the crack widths in the constant moment zone, which yielded a good correlation between the predictions and the experiments. The short fibres mostly contributed to the flexural response in the serviceability limit state, but only slightly increased the shear resistance due to their low fibre effectiveness. The introduction of bond shear connectors was shown to be essential to prevent the premature delamination of the reinforcement. The use of tall connectors allowed doubling the bearing capacity with respect to the flat reinforcement without any spatial features, effectively bridging the governing crack and reaching the tensile capacity of the longitudinal textile reinforcement., The authors gratefully acknowledge Dr Mariana Popescu from Block Research Group (ETHZ) and Dr Lex Reiter from the Chair of Physical Chemistry of Building Materials (ETHZ) for contributing their technical and practical expertise as well as the students Nathalie Chiaverio and Caterina Rovati for their valuable support during preparation and testing of the specimens shown in this paper. This research is supported by the National Centre for Competence in Research in Digital Fabrication, funded by the Swiss National Science Foundation (project number 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structural Stay-in-Place Formwork for Robotic in Situ Fabrication of Non-Standard Concrete Structures: A Real Scale Architectural Demonstrator

  • Hack, Norman
  • Dörfler, Kathrin
  • Walzer, Alexander Nikolas
  • Wangler, Timothy
  • Kumar, Nitish
  • Buchli, Jonas
  • Kaufmann, Walter
  • Flatt, Robert J.
  • Gramazio, Fabio
  • Kohler, Matthias
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Concrete is a highly versatile construction material, not only for the reason that it has excellent properties in terms of structural performance, building physics, availability and price, but also because it can be moulded into virtually any shape regardless of its geometric complexity. However, even though current digital design tools allow to effortlessly design and calculate structures, which are exploiting these properties, this potential remains all too often unrealized. This is due to the fact that geometrically complex concrete structures require expensive, one-of-a kind formwork, which can often not be reused or even recycled. Consequently, the current practice for producing non-standard curvilinear architecture in reinforced concrete is neither ecologically sustainable nor economically feasible for a broader range of architectural typologies. Additive Manufacturing (AM) processes, like 3D printing with concrete, on the other hand, currently struggle with the integration of structural reinforcement, limiting the technique to predominantly compression-loaded applications. This research addresses both issues and proposes Mesh Mould, a robotic fabrication process that unifies concrete formwork and structural reinforcement, and hence potentially reduces formwork waste and construction costs for non-standard reinforced concrete constructions. The development of a fully automated robotic fabrication process involved various research disciplines, including architecture, material science, mechanical engineering, robotics as well as civil engineering. This paper describes the technological developments of the Mesh Mould construction system that were necessary to meet the challenges of 1:1 construction. The results are demonstrated in a final loadbearing structure, the Mesh Mould wall of the DFAB HOUSE on NEST., The Mesh Mould research was a highly interdisciplinary research project conducted within the framework of National Center of Competence in Research Digital Fabrication (NCCR Digital Fabrication, Agreement #51NF40-141853), supported by Swiss National Science Foundation.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Interaction of reinforcement, process, and form in Digital Fabrication with Concrete

  • Kloft, Harald
  • Sawicki, Bartlomiej
  • Bos, Freek P.
  • Dörrie, Robin
  • Freund, Niklas
  • Gantner, Stefan
  • Gebhard, Lukas
  • Hack, Norman
  • Ivaniuk, Egor
  • Kruger, Jacques
  • Kaufmann, Walter
  • Mechtcherine, Viktor
  • Mirjan, Ammar
  • Wolfs, Rob
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Material, manufacturing process, and form are mutually dependent. In formwork-based concrete construction, the reinforcement must be positioned and fixed in the formwork, limiting material efficiency and freedom of form. In Digital Fabrication with Concrete (DFC), the formwork no longer limits the concrete forming process. Furthermore, the reinforcement no longer must be installed in advance, but can be placed before, during or after the concrete application. Therefore, the role of reinforcement and its interaction with processing must be fundamentally rethought in DFC. Furthermore, with reinforcement integration a concrete component expands from a contour-based shape into a structural form. The current paper proposes a new so-called RPF-framework expressing the interaction of reinforcement, process and form in DFC. The application of this framework is illustrated using current examples of DFC, whose structural forms are critically discussed. Finally, the need for a holistic approach to material, process and form in DFC is emphasised., The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: H. Kloft, R. Dorrie, N. Freund, S. Gantner, N. Hack, D. Lowke reports financial support was provided by German Research Foundation (DFG) Collaborative Research Centre Transregio 277 Additive Manufacturing in Construction (TRR 277 AMC) Project Number 414265976. L. Gebhard, W. Kaufmann reports financial support was provided by Swiss National Science Foundation (SNSF) National Centres of Competence in Research Digital Fabrication (dfab) Project Number 51NF40-141853. E. Ivaniuk, V. Mechtcherine reports financial support was provided byGerman Research Foundation (DFG) Priority Programme 2005 Opus Fluidum Futurum-Rheology of reactive, multiscale, multiphase construction materials (SPP 2005) . If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.r German Research Foundation (DFG) Priority Programme 2005 Opus Fluidum Futurum-Rheology of reactive, multiscale, multiphase con-struction materials (SPP 2005) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Design and fabrication of optimised ribbed concrete floor slabs using large scale 3D printed formwork

  • Burger, Joris
  • Huber, Tobias
  • Lloret-Fritschi, Ena
  • Gramazio, Fabio
  • Kohler, Matthias
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] This paper describes the design, fabrication, and testing process of an optimised, reinforced concrete ribbed floor slab fabricated using robotically 3D printed formwork. The design of the floor slab is based on the alignment of ribs along the trajectories of the principal bending moments. A workflow is described that generates a rib layout based on structural analysis, which is used to create a three-dimensional model of the slab. A full-scale prototype is fabricated by using an industrial robotic arm with a pellet extruder mounted as an end effector to 3D print the formwork. Reinforcement is inserted and the formwork is cast using self-compacting concrete. The successful design, fabrication, and structural testing of the full-scale floor slab prototype showed that the described workflow is suitable for realizing material-optimised, ribbed reinforced concrete floor slabs using 3D printed formwork., This project was funded by Siemens, Geberit and the ETH Zurich Foundation. This research was further supported by the The Swiss National Science Foundation (NCCR Digital Fabrication agreement number 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Digitally fabricated ribbed concrete floor slabs: a sustainable solution for construction

  • Mata Falcon, Jaime|||0000-0001-8701-4410
  • Bichof, Patrick
  • Huber, Tobias
  • Anton, Ana
  • Burger, Joris
  • Ranaudo, Francesco
  • Jipa, Andrei
  • Gebhard, Lukas
  • Reiter, Lex
  • Lloret-Fritschi, Ena
  • Van Mele, Tom
  • Block, Philippe
  • Gramazio, Fabio
  • Kohler, Matthias
  • Dillenburger, Benjamin
  • Wangler, Timothy
  • Kaufmann, Walter
[EN] The concrete used in floor slabs accounts for large greenhouse gas emissions in building construction. Solid slabs, often used today, consume much more concrete than ribbed slabs built by pioneer structural engineers like Hennebique, Arcangeli and Nervi. The first part of this paper analyses the evolution of slab systems over the last century and their carbon footprint, highlighting that ribbed slabs have been abandoned mainly for the sake of construction time and cost efficiency. However, highly material¿efficient two¿way ribbed slabs are essential to reduce the environmental impact of construction. Hence, the second part of this paper discusses how digital fabrication can help to tackle this challenge and presents four concrete floor systems built with digitally fabricated formwork. The digital fabrication technologies employed to produce these slab systems are digital cutting, binder¿jetting, polymer extrusion and 3D concrete printing. The presented applications showcase a reduction in concrete use of approximately 50% compared to solid slabs. However, the digitally fabricated complex formworks produced were wasteful and/or labour¿intensive. Further developments are required to make the digital processes sustainable and competitive by streamlining the production, using low carbon concrete mixes as well as reusing and recycling the formwork or structurally activating stay¿in¿place formwork., The authors gratefully acknowledge Professor Robert Flatt from the Chair of Physical Chemistry of Building Materials (ETH Zurich) for contributing his technical and practical expertise, as well as the students Johanna Renner and Magnus List for their sustainability analysis of ribbed slabs [54] shown in this paper. The ideas presented in this paper originated from discussions within the National Centre for Competence in Research in Digital Fabrication, funded by the Swiss National Science Foundation (project number 51NF40‐ 141853). Thisresearch containsinputsfrom open discussions with many colleagues not authoring this contribution. We would sincerely like to thank them for their selfless collaborative spirit.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fostering innovative and sustainable mass-market construction using digital fabrication with concrete

  • Bichof, Patrick
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] The construction industry produces buildings and infrastructure. These construction works are typically immobile and customised, and must meet many criteria to provide value to modern society: structural safety, durability, serviceability, aesthetics and integration, environmental sustainability and construction efficiency. Accordingly, traditional construction methods, along with the resulting construction works, have been adapted to comply with these multifaceted requirements for more than a century. However, the construction industry has a considerable environmental impact, with reinforced concrete as its primary driver due to its extensive use, and will be facing an ever-increasing responsibility to tackle climate neutrality in the upcoming years. Digital fabrication with concrete is a young yet already broad discipline that brings about the potential for the necessary reduction of the environmental impact and further industrialisation of the construction industry while being compatible with the multifaceted requirements for construction works. Still, it has not penetrated the construction mass market, which is paramount for making a significant difference towards improving the environmental impact of the construction industry. The present study tackles this issue by (i) assessing traditional construction and digital fabrication on a value-driven basis, identifying and summarising their inherent strengths and challenges, and (ii) proposing a value-driven ideation process to identify relevant mass-market levers of digital fabrication in the construction industry. The presented methodology indicates two exemplary applications of how traditional construction and digital fabrication processes can be combined to tackle the persistent environmental sustainability challenges., This research is supported by the National Centre for Competence in Research in Digital Fabrication in Architecture, funded by the Swiss National Science Foundation (project number 51NF40 141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Load-deformation behaviour of weft-knitted textile reinforced concrete in uniaxial tension

  • Lee, Minu
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Weft-knitted textiles offer many advantages over conventional woven fabrics since they allow the fabrication of doubly curved geometries without the need of stitching multiple patches together. This study investigated the use of highstrength continuous fibres as knitted textile reinforcement, focusing on various knitting patterns, fibre materials, coating types and spatial features to enhance the bond conditions between concrete and reinforcement. The bond is of particular interest since the contact surface of knitted textiles is fundamentally different due to their closed surface, compared to commercially available textile reinforcement, which is normally formed as orthogonally woven grids of ovings. An experimental campaign consisting of 28 textile-concrete composites was conducted, where digital image correlation-based measurements were used to assess the load-deformation behaviour and to analyse the crack kinematics. The results showed a beneficial post-cracking behaviour for epoxy coated configurations with straight inlays. The comparison of these configurations with conventional textile reinforcement generally showed a similar behaviour, but with higher utilisation compared to the filament strength. The Tension Chord Model, which assumes a constant bond stress-slip relationship, was adapted for the specific geometry of the knitted reinforcement, and it was used for the estimation of bond stresses and a post-diction of the experimental results, generally showing a good agreement., Open Access funding provided by ETH Zurich. This research is supported by the National Centre for Competence in Research in Digital Fabrication, funded by the Swiss National Science Foundation (project number 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Rethinking reinforcement for digital fabrication with concrete

  • Asprone, Domenico
  • Menna, Costantino
  • Bos, Freek P.
  • Salet, Theo A.M.
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] The fabrication of novel reinforced concrete structures using digital technologies necessarily requires the definition of suitable strategies for reinforcement implementation. The successful integration of existing reinforcement systems, such as steel rebar, rods, wires, fibres or filaments, will indeed allow for printed concrete structures to be designed using standard structural codes. However, reinforcement integration has to be compatible with either the specific printing technique adopted for the structural element production or with its shape. This paper provides a systematic overview of a number of digital fabrication techniques using reinforced concrete that have been developed so far, proposing a possible organization by structural principle, or place in the manufacturing process., This research is partially supported by: the National Centre for Competence in Research in Digital Fabrication in Architecture, funded by the Swiss National Science Foundation (project number 51NF40_141853); the TU/e research program on 3DCP, co-funded by a partner group of enterprises and associations, which as of the date of writing consisted of (alphabetical order) Ballast Nedam, BAM Infraconsult bv, Bekaert, Concrete Valley, CRH, Cybe, Saint-GobainWeber Beamix, SGS Intron, SKKB, Van Wijnen, Verhoeven Timmerfabriek, and Witteveen + Bos. Their support is gratefully acknowledged. In particular, the authors would like to thank SGWeber Beamix and Bekaert NV for supplying the printing concrete and reinforcement cables, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structural behaviour of 3D printed concrete beams with various reinforcement strategies

  • Gebhard, Lukas
  • Anton, Ana
  • Dillenburger, Benjamin
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] 3D concrete printing (3DCP) offers many new possibilities. This technology could increase the productivity of the construction industry and reduce its environmental impact by producing optimised structures more efficiently. Despite significant developments in materials science, little effort has been put in developing reinforcement strategies compatible with 3DCP and on the characterisation of their structural behaviour. Consequently, 3DCD still lacks compliance with structural integrity requirements. This study presents an experimental investigation consisting of nine four-point bending tests on extrusion 3DCP beams reinforced with various types of reinforcement. As interlayer shear reinforcement, aligned end-hook fibres (0.3 and 0.6%) or steel cables (0.1%) placed between the layers of printed concrete were used. As longitudinal reinforcement, unbonded posttensioning and conventional bonded passive reinforcement were explored. The crack patterns and their associated kinematics were tracked using digital image correlation. The results show that the post-tensioned beams failed in a brittle manner due to the crushing of concrete in bending, with deformations localised in a few bending cracks. In the beams with conventional bonded longitudinal reinforcement, both bending as well as shear cracks were generated, and the brittle failure of the interlayer shear reinforcement limited the ultimate load. Estimations based on the measured crack kinematics show that the interlayer shear reinforcement carried most of the applied shear force. Based on these results, a simple mechanical model is developed to understand the mechanical behaviour and to pre-design the required amount of interlayer shear reinforcement., The authors gratefully acknowledge the support of ETH students Jonathan Ensslin, Moritz Studer, JeanLuc Imhof and Vanessa Studer in the production, preparation and testing of the beams. The authors would like to acknowledge the collaboration with Dr. Lex Reiter, Dr. Timothy Wangler, and Prof. Dr. Robert J. Flatt from the chair of Physical Chemistry of Building Materials, ETH Zurich, for the development of the 3DCP mix design and the set ondemand printing process. The authors would also like to express their gratitude for their support to the technical teams of the IBK Structures Lab, the NCCR dfab Robotic Fabrication Lab, and the IfB Concrete Lab at ETH Zurich. This work was funded by the Swiss National Science Foundation, within the National Centre for Competence in Research in Digital Fabrication (project number 51NF40141853) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structural behaviour of post-installed reinforcement for 3D concrete printed shells A case study on water tanks

  • Gebhard, Lukas
  • Iqbal, Arshalan
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Incorporating sufficient reinforcement to ensure a ductile structural behaviour is a persisting challenge in digitally fabricated concrete structures. This paper investigates the structural performance of a reinforcement approach for 3D concrete printed elements, consisting of an unreinforced 3D printed concrete shell and a sprayed shell reinforced with a conventional reinforcing mesh for application in water tanks. Four reinforced concrete elements produced with this approach were tested in direct tension and compared to a reference test of a monolithic specimen to analyse the behaviour of circular water tanks under hoop stresses. Two eccentric reinforcement arrangements and two different printing patterns were investigated. Despite the testing setup not perfectly representing the actual behaviour of circular water tanks, in which shell deformations are kinematically restrained, the feasibility of the fabrication method could be examined. The results did not show significant differences in the behaviour of the different fabrication methods, with similar ductility as expected in a conventionally reinforced shell. The eccentric reinforcement caused the crack formation to originate on the surface close to the reinforcement, accompanied by out-of-plane deformations. The cracks on the far side of the reinforcement opened suddenly and reduced the out-of-plane deformations. The predictions with models neglecting the eccentricity of the reinforcement overestimated the crack opening. The best predictions were obtained from the tension chord model by only considering the concrete area defined by twice the mechanical cover of the reinforcement., The authors would like to thank Knauf Gips KG for partially funding this study. The experimental campaign was funded by the Swiss National Science Foundation within the National Centre for Competence in Research in Digital Fabrication (project number 51NF40-141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Opportunities and Challenges for Structural Engineering of Digitally Fabricated Concrete

  • Menna, Costantino
  • Bos, Freek P.
  • Vantyghem, Gieljan
  • Ferrara, Liberato
  • Asprone, Domenico
  • Salet, Theo A.M.
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Digital fabrication technologies utilizing concrete (DFC) have recently enabled form freedom for the production of a variety of concrete-made objects having mainly architectural and aesthetic functions. Structural elements or civil/building structures made by DFC demonstrate a high engineering potential, mainly for tailoring the final shape while optimising the structural/functional performance, material use, overall costs, and architectural effectiveness. However, the design of structurally efficient DFC constructions or components is often faced with a lack of a common structural engineering approach that can adapt to specific DFC particularities. In this paper, we provide a systematic overview of a number of DFC structural projects developed thus far. A comprehensive discussion about structural engineering details is provided, addressing the related fundamental structural issues and envisioning opportunities and challenges toward achieving the full potential of DFC., Dr. Mata-Falcon and Prof. Kaufmann would like to thank the Swiss National Science Foundation for support of most ETH-based work reported in this paper, along with partial financial support for Dr. MataFalcon (National Centre for Competence in Research in Digital Fabrication in Architecture: project number 51NF40_141853).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancing structural efficiency with digital concrete-Principles, opportunities and case studies

  • Gebhard, Lukas
  • Ammann, Rebecca
  • Pressmair, Nadine
  • Kromoser, Benjamin
  • Menna, Costantino
  • Baghdadi, Abtin
  • Kloft, Harald
  • Gabriel, Michael
  • Walch, Martin
  • Kaufmann, Walter
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] This paper explores the opportunities of digital fabrication with concrete (DFC) to improve structural efficiency and achieve sustainable construction. Efficient structural solutions that drastically reduce material consumption can be achieved by ensuring direct load flow and placing material where needed. More than 50% of material savings can be achieved by using flanges or hollow sections, providing continuity in beams or slabs, reducing the span of structures or using structural systems such as arches, trusses or deep beams. These concepts are not fully exploited as they often require expensive and complex formwork. DFC tackles the latter point, as it promises to produce complex geometries, minimising extra effort, cost, or waste. The paper discusses the optimisation potential of DFC for several structural elements and presents existing applications that demonstrate this potential. Five case studies of different technological approaches are discussed in detail, highlighting advantages and disadvantages to be addressed for widespread adoption., For the project "Bauhof Bludenz" the authors want to express their gratitude to the involved parties (Client: Werit Handels GmbH, User: City of Bludenz, Architect: Atelier Ender | Architektur, General Contractor: Tomaselli Gabriel Bau, Structural Engineer: gbd ZT GmbH, Scientific Support: TU Graz, Institute for Structural Design, Manufacturing of Formworks: Concrete 3D) . The research was funded by the Swiss National Science Foundation - National Centre for Competence in Research in Digital Fabrication (project number 51NF40-141853) , as well as by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) - Projektnummer 414265976 - TRR 277. Sub-project: C05-A04.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Inter-laboratory study on the influence of 3D concrete printing set-ups on the bond behaviour of various reinforcements

  • Gebhard, Lukas
  • Esposito, Laura
  • Menna, Costantino
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] This study investigates the influence of different printing set-ups and materials on the bond strength of reinforcement manually placed between 3D printed concrete layers. An identical experimental campaign was performed at two institutes in Switzerland and Italy. Each institute used its own printing process, which consisted either of a set on-demand mix or a high yield stress material. Two types of reinforcement (reinforcing bar Ø8 mm and a high strength steel wire Ø1 mm) and three production configurations (casting and printing with the reinforcement parallel or perpendicular to the printing direction) were investigated. The results showed high bond strength with only a limited influence of the fabrication method for the reinforcing bars. An increased bond was observed for the set on-demand approach compared to the high yield strength material. The comparison with existing models showed that the reinforcing bar bond strength of printed concrete varies slightly from conventional concrete. The high strength wires exhibited poor bond. Based on the gathered experiences, insights into the standardisation of testing for 3D concrete printing are discussed., The authors would like to thank the team of Etesias (Napoli, Italy) and Ana Anton (Digital Building Technologies, ETH Zurich) and Lex Reiter (Chair of Physical Chemistry of Building Materials, ETH Zurich) for their support in the printing laboratory. Furthermore, the authors are grateful for the support of the two teams of the structural labs at both institutes. At ETH Zurich, the experimental campaign was funded, and the exchange was supported by the Swiss National Science Foundation, within the National Centre for Competence in Research in Digital Fabrication (project number 51NF40-141853) . At UniNa, the experi-mental activities were supported by Italcementi Heidelberg CementGroup (industrial partner of the PhD program) and by the Italian Ministry of University and Research (MIUR) under program PON 2014-2020 (CCI 2014IT16M2OP005) . A special thanks for enabling the exchange and supporting the research goes to Prof. Dr. Walter Kaufmann (ETH Zurich).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

From Smart Dynamic Casting to a growing family of Digital Casting Systems

  • Lloret-Fritschi, Ena
  • Wangler, Timothy
  • Gebhard, Lukas
  • Mantellato, Sara
  • Scotto, Fabio
  • Burger, Joris
  • Szabo, Anna
  • Ruffray, Nicholas
  • Reiter, Lex
  • Boscaro, Federica
  • Kaufmann, Walter
  • Kohler, Matthias
  • Gramazio, Fabio
  • Flatt, Robert
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] Over the past decade innovative techniques for shaping concrete have emerged, all aiming to use less material and reduce the need for traditional formwork. One very promising method is to shape concrete dynamically: referred to as Smart Dynamic Casting (SDC), this process was pioneered in 2012 as the first robotically-driven system for slipforming bespoke concrete structures. The process has successfully been adapted to produce structures using ultra-thin formworks that are cast using our digital set-on-demand procedure. More generally we frame this approach as Digital Casting Systems (DCS), which allows the user precisely to determine the hydration rate of the material, thus eliminating formwork pressure. This paper highlights the major findings from SDC that led us to continue developing DCS. It lays out the material concepts fundamental the family of DCS, which, by eliminating the need for bulky formworks, has a large potential impact on future construction methods., The authors would like to thank the ETH Zurich for providing the Research Grant ETH-13 12-1. This grant laid the basis for a still ongoing collaboration between various ETH Zurich Researchers. Further we would like to thank the National Centre of Competence in Research in Digital Fabrication in Architecture, funded by the Swiss National Science Foundation (project number 51NF40:141853), for giving the opportunity to continue the investigate novel construction methods for the future of concrete construction.