Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Stratigraphy of a diamond epitaxial three-dimensional overgrowth using doping superlattices

  • Lloret Vieira, Fernando Manuel
  • Fiori, Alexandre
  • Araújo Gay, Daniel
  • Eon, David
  • Villar Castro, María del Pilar
  • Bustarret, Etienne
The selective doped overgrowth of 3D mesa patterns and trenches has become an essential fabrication step of advanced monolithic diamond-based power devices. The methodology here proposed combines the overgrowth of plasma-etched cylindrical mesa structures with the sequential growth of doping superlattices. The latter involve thin heavily boron doped epilayers separating thicker undoped epilayers in a periodic fashion. Besides the classical shape analysis under the scanning electron microscope relying on the appearance of facets corresponding to the main crystallographic directions and their evolution toward slow growing facets, the doping superlattices were used as markers in oriented cross-sectional lamellas prepared by focused ion beam and observed by transmission electron microscopy. This stratigraphic approach is shown here to be applicable to overgrown structures where faceting was not detectable. Intermediate growth directions were detected at different times of the growth process and the periodicity of the superlattice allowed to calculate the growth rates and parameters, providing an original insight into the planarization mechanism. Different configurations of the growth front were obtained for different sample orientations, illustrating the anisotropy of the 3D growth. Dislocations were also observed along the lateral growth fronts with two types of Burger vector: b 01 1 = 1 2 [01 1 ] and b 112 = 1 6 [112]. Moreover, the clustering of these extended defects in specific regions of the overgrowth prompted a proposal of two different dislocation generation mechanisms.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Control of the alumina microstructure to reduce gate leaks in diamond MOSFETs

  • Gutiérrez Peinado, Marina
  • Lloret Vieira, Fernando Manuel
  • Thanh-Toan, Pham
  • Cañas, Jesus
  • Fernández de los Reyes, Daniel
  • Eon, David
  • Pernot, Julien
  • Araújo Gay, Daniel
In contrast to Si technology, amorphous alumina cannot act as a barrier for a carrier at diamond MOSFET gates due to their comparable bandgap. Indeed, gate leaks are generally observed in diamond/alumina gates. A control of the alumina crystallinity and its lattice matching to diamond is here demonstrated to avoid such leaks. Transmission electron microscopy analysis shows that high temperature atomic layer deposition, followed by annealing, generates monocrystalline reconstruction of the gate layer with an optimum lattice orientation with respect to the underneath diamond lattice. Despite the generation of γ-alumina, such lattice control is shown to prohibit the carrier transfer at interfaces and across the oxide.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Lattice performance during initial steps of the Smart-Cut™ process in semiconducting diamond: A STEM study

  • Piñero Charlo, José Carlos
  • de Vecchy, John
  • Fernández de los Reyes, Daniel
  • Alba Muñoz, Gonzalo
  • Widiez, J
  • Di Cioccio, L
  • Lloret Vieira, Fernando Manuel
  • Araújo Gay, Daniel
  • Pernot, Julien
An alternative route for the development of diamond-based technologies is the Smart-Cut process. Such a process could make possible the combination of diamond and silicon technologies, as well as building alternative structures or manufacturing large diamond wafers. However, crystalline quality and implantation-related damages may alter the electronic properties of the diamond wafer. In fact, this is a critical bottleneck that needs to be analysed in order to develop a reliable diamond/Smart-Cut based technology. In this contribution, we present STEM-based experiments used to evaluate various key parameters such as the sharpness of the transition regions, the behaviour of the implanted region and diamond lattice performance in Smart-Cut processes. Indeed, an outstanding sp2/sp3 relation close to ideality (it is, that of undamaged diamond) is evidenced in the diamond-transfer region.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

MPCVD Diamond Lateral Growth Through Microterraces to Reduce Threading Dislocations Density

  • Lloret Vieira, Fernando Manuel
  • Gutiérrez Peinado, Marina
  • Araújo Gay, Daniel
  • Eon, David
  • Bustarret, Etienne
Diamond lateral growth is a useful technique to assess 3D architectures of devices. The requirement of the overgrowth on etched substrates has been observed to have additional benefit in the crystallinity of the diamond. The surface roughness is enhanced and threading dislocation density is reduced as a consequence of the lateral growth on patterned substrates. Under these premises, this contribution presents a study of defects and terrace coalescences for the lateral growth on a trenched surface substrates with different trench widths. The latter was achieved on 100-oriented HPHT diamond substrates grown by MPCVD and using very thin-doped layers to mark the growth plane every 100 nm. The results showed high density of threading dislocations that were gathered to the centre of the coalescence. These threading dislocations, as well as planar defects, were investigated using transmission electron microscopy. The mechanism of those defects generation and the better conditions to achieve defect-free areas are discussed.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Three-Dimensional Diamond MPCVD Growth over MESA Structures: A Geometric Model for Growth Sector Configuration

  • Lloret Vieira, Fernando Manuel
  • Araújo Gay, Daniel
  • Eon, David
  • Bustarret, Etienne
The overgrowth of {100}-oriented patterned diamond substrates by microwave plasma enhanced chemical vapor deposition was studied by transmission electron microscopy through a stratigraphic approach. A sector-like growth behavior is evidenced, resulting from a competition between slowly growing facets at protruding (top) corners and edges against quickly growing facets at recessing (bottom) corners. Depending on the pattern orientation and height, under some particular experimental conditions, it is possible to predict the sequence of growth sectors, and thus to choose the crystallographic orientation of the overgrown surface, by stopping the growth at the right stage. A simple two-dimensional model is provided, allowing the fabrication of structures adapted to the requirements of specific electronic devices.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Crystalline defects induced during MPCVD lateral homoepitaxial diamond growth

  • Lloret Vieira, Fernando Manuel
  • Eon, David
  • Bustarret, Etienne
  • Araújo Gay, Daniel
The development of new power devices taking full advantage of the potential of diamond has prompted the design of innovative 3D structures. This implies the overgrowth towards various crystallographic orientations. To understand the consequences of such growth geometries on the defects generation, a Transmission Electron Microscopy (TEM) study of overgrown, mesa-patterned, homoepitaxial, microwave-plasma-enhanced, chemical vapor deposition (MPCVD) diamond is presented. Samples have been grown under quite different conditions of doping and methane concentration in order to identify and distinguish the factors involved in the defects generation. TEM is used to reveal threading dislocations and planar defects. Sources of dislocation generation have been evidenced: (i) doping level versus growth plane, and (ii) methane concentration. The first source of dislocations was shown to generate <110> Burgers vector dislocations above a critical boron concentration, while the second induces <112> type Burgers vector above a critical methane/hydrogen molar ratio. The latter is attributed to partial dislocations whose origin is related to the dissociation of perfect ones by a Shockley process. This dissociation generated stacking faults that likely resulted in penetration twins, which were also observed on these samples. Lateral growth performed at low methane and boron content did not exhibit any dislocation.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Boron-doping proximity effects on dislocation generation during non-planar MPCVD homoepitaxial diamond growth

  • Lloret Vieira, Fernando Manuel
  • Eon, David
  • Bustarret, Etienne
  • Fiori, Alexandre
  • Araújo Gay, Daniel
Epitaxial lateral growth will be required if complex diamond-based device architecture, such as, for example, Metal-oxide-semiconductor Field-effect transistors (MOSFETs) or epitaxial lateral overgrowth (ELO) substrates, need to be developed for high-power applications. To this end, undoped and doped non-planar homoepitaxial diamond were overgrown on (001)-oriented diamond-patterned substrates. Defects induced by both the heavy boron doping and three-dimensional (3D) growth were studied by transmission electron microscopy (TEM). At high methane and boron concentrations, threading dislocations with Burgers vectors b = 1/6 〈211〉, b = 1/2 〈110〉, or both were observed. Their generation mechanisms were established, revealing boron proximity effects as precursors of dislocations generated in boron-doped samples and providing clues as to the different Burgers vectors. The concentration ranges of boron and methane resulting in good crystalline quality depended on the plane of growth. The microwave plasma-enhanced chemical vapour deposition (MPCVD) growth conditions and the maximum boron concentration versus plane orientation yielding a dislocation-free diamond epitaxial layer were determined
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

High quality Al2O3/(100) oxygen-terminated diamond interface for MOSFETs fabrication

  • Pham, T. T.
  • Gutiérrez Peinado, Marina
  • Masante, C.
  • Rouger, N.
  • Eon, D.
  • Gheeraert, Etienne
  • Araújo Gay, Daniel
  • Pernot, Julien
In this letter, we report on the improvement of gate controlled Al2O3/(100) boron doped (B-doped) oxygen-terminated diamond (O-diamond) Metal Oxide Semiconductor Capacitors using 40 nm thick Al2O3 deposited by Atomic Layer Deposition at 380 °C and then annealed at 500 °C in vacuum conditions. The high quality of Al2O3 and an Al2O3/diamond interface is verified thanks to electrical measurements and Transmission Electron Microscopy (TEM) measurements. A density of interface states lower than 1012 eV-1 cm-2 is measured from the flat-band regime to the depletion regime. The shift of the flat-band voltage and the leakage current through the oxide are significantly reduced in good agreement with the mono-crystalline character of the Al2O3 layer revealed by TEM
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Impact of methane concentration on surface morphology and boron incorporation of heavily boron-doped single crystal diamond layers

  • Rouzbahani, Rozita
  • Nicley, Shanon S
  • Vanpoucke, Danny E P
  • Lloret Vieira, Fernando Manuel
  • Pobedinskas, Paulius
  • Araújo Gay, Daniel
  • Haenen, Ken
The methane concentration dependence of the plasma gas phase on surface morphology and boron incorporation in single crystal, boron-doped diamond deposition is experimentally and computationally investigated. Starting at 1%, an increase of the methane concentration results in an observable increase of the B-doping level up to 1.7×1021 cm−3, while the hole Hall carrier mobility decreases to 0.7±0.2 cm2 V−1 s−1. For B-doped SCD films grown at 1%, 2%, and 3% [CH4]/[H2], the electrical conductivity and mobility show no temperature-dependent behavior due to the metallic-like conduction mechanism occurring beyond the Mott transition. First principles calculations are used to investigate the origin of the increased boron incorporation. While the increased formation of growth centers directly related to the methane concentration does not significantly change the adsorption energy of boron at nearby sites, they dramatically increase the formation of missing H defects acting as preferential boron incorporation sites, indirectly increasing the boron incorporation. This not only indicates that the optimized methane concentration possesses a large potential for controlling the boron concentration levels in the diamond, but also enables optimization of the growth morphology. The calculations provide a route to understand impurity incorporation in diamond on a general level, of great importance for color center formation.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Diamond/γ-alumina band offset determination by XPS

  • Cañas, Jesus
  • Alba Muñoz, Gonzalo
  • Leinen, Dietmar
  • Lloret Vieira, Fernando Manuel
  • Gutiérrez Peinado, Marina
  • Eon, David
  • Pernot, Julien
  • Gheeraert, Etienne
  • Araújo Gay, Daniel
γ-Alumina is a promising candidate for fabricating the gate of the diamond metal oxide semiconductor field effect transistor based on oxygen termination due to its high bandgap of 6.7 eV and high static dielectric constant of 9. Besides these properties, having a sufficient barrier for holes is mandatory to avoid carriers leakage through the gate. However, the band offset of the diamond/alumina heterojunction can be affected by the alumina crystallinity and interface bonds, which depend on multiple factors such as deposition and annealing temperature or diamond surface treatment prior to deposition. In this work, the heterojunction of atomic layer deposited alumina and (1 0 0) p-diamond is studied using X-ray photoelectron spectroscopy (XPS). Transmission electron microscopy studies reveal that the deposited alumina layer is 35 nm thick and present the gamma phase. The valence band offset between diamond and γ-alumina is evaluated on a single sample with a new methodology based on an ion etching XPS depth profile. The obtained value for the valence band offset of diamond and γ-alumina is 3.4 eV.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Influence of methane concentration on MPCVD overgrowth of 100-oriented etched diamond substrates

  • Lloret Vieira, Fernando Manuel
  • Araújo Gay, Daniel
  • Eon, David
  • Villar Castro, María del Pilar
  • González Leal, Juan María
  • Bustarret, Etienne
Selective diamond growth on etched diamond substrates allows the development of 3D-type device geometries, which can make possible higher capacity, higher surface for contacts and benefits from better properties versus growth orientation. Such structures need the control of lateral growth or lateral etching that guarantee the best epitaxial growth, with a well-faceted surface, with a minimum density of emerging defects in order to limit the current leakage and to improve the breakdown voltage. Previous works used 111-oriented selective growth on etched diamond for lateral p–n junctions or bipolar junction transistors. The behavior of homoepitaxial overgrowth on etched diamond substrates depends directly on growth parameters such as temperature, gas concentration or microwave power that can favor the growth in one specific direction. The present contribution considers the effect of methane concentration during the overgrowth of the mesa pattern. The presence of highly doped intermediate layers allowed following the growth plane orientation in a stratigraphic approach. Faceting and growth velocities were analyzed using scanning and transmission electron microscopes (SEM and TEM).