Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Design Guidelines for Thermally Driven Micropumps of Different Architectures Based on Target Applications via Kinetic Modeling and Simulations

  • López Quesada, Guillermo
  • Tatsios, Giorgos
  • Valougeorgis, Dimitris
  • Rojas Cárdenas, Marcos
  • Baldas, Lucien
  • Barrot, Christine
  • Colin, Stéphane
This article belongs to the Special Issue Gas Flows in Microsystems, The manufacturing process and architecture of three Knudsen type micropumps are discussed and the associated flow performance characteristics are investigated. The proposed fabrication process, based on the deposition of successive dry film photoresist layers with low thermal conductivity, is easy to implement, adaptive to specific applications, cost-effective, and significantly improves thermal management. Three target application designs, requiring high mass flow rates (pump A), high pressure differences (pump B), and relatively high mass flow rates and pressure differences (pump C), are proposed. Computations are performed based on kinetic modeling via the infinite capillary theory, taking into account all foreseen manufacturing and operation constraints. The performance characteristics of the three pump designs in terms of geometry (number of parallel microchannels per stage and number of stages) and inlet pressure are obtained. It is found that pumps A and B operate more efficiently at pressures higher than 5 kPa and lower than 20 kPa, respectively, while the optimum operation range of pump C is at inlet pressures between 1 kPa and 20 kPa. In all cases, it is advisable to have the maximum number of stages as well as of parallel microchannels per stage that can be technologically realized., This project was funded by the European Union’s Framework Programme for Research and Innovation Horizon 2020 (2014-2020) under the Marie Skłodowska-Curie (grant agreement number. 643095).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Thermally driven pumps and diodes in multistage assemblies consisting of microchannels with converging, diverging and uniform rectangular cross sections

  • López Quesada, Guillermo
  • Tatsios, Giorgios
  • Valougeorgis, Dimitris
  • Rojas Cárdenas, Marcos
  • Baldas, Lucien
  • Barrot, Christine
  • Colin, Stéphane
Each stage is formed by combining in series-long microchannels with (a) uniform–uniform (“uni–uni”), (b) converging–uniform (“con–uni”), (c) diverging–uniform (“div–uni”) and (d) converging–diverging (“con–div”) rectangular cross sections. In all four investigated assemblies the generated pressure difference with the associated mass flow rate is fully assessed, in terms of inlet pressure, inclination parameter and number of stages. The analysis is based on linear kinetic modeling and is valid in the whole range of gas rarefaction. It is concluded that the “con–uni” and “div–uni” assemblies provide higher pressure differences and lower mass flow rates than the “uni–uni” assembly and they may be more suitable for specific pumping applications. The characteristics of the “con–uni” and “div–uni” assemblies are very close to each other. The multistage “uni–uni”, “con–uni” and “div–uni” assemblies are more stable when operating at small inlet pressures, where the pressure difference remains almost constant in wide ranges of mass flow rate. It is advisable to add as many stages as possible to increase, depending on the application, either the pressure difference or mass flow rate or both. Furthermore, the “con–div” assembly provides smaller pressure differences and mass flow rates than the other three, but it is suitable for diode applications. It is characterized by the so-called blocking inlet pressure, where the deduced pressure difference in the converging and diverging channels is the same. A detailed parametrization of the blocking inlet pressure in terms of inclination ratio, mean height, temperature difference and gas species, has been performed. It is concluded that multistage “con–div” assemblies may be ideally applied as thermally driven microfluidic diodes to control or block the flow, as well as to separate the species in multicomponent gas mixtures., This work has received funding from the European Union’s Framework Programme for Research and Innovation Horizon 2020 (2014–2020) under the Marie Skłodowska-Curie Grant Agreement No. 643095. This work was partly supported by the French Renatech network: The technical information and constraints received from Laboratoire d’Analyse et d’Architecture des Systèmes in Toulouse, France, regarding the manufacturing process to be implemented in the short future are highly acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Review of Optical Thermometry Techniques for Flows at the Microscale towards Their Applicability to Gas Microflows

  • Colin, Stéphane
  • Fernández Sánchez, José María
  • Barrot, Christine
  • Baldas, Lucien
  • Bajić, Slaven
  • Rojas-Cárdenas, Marcos
52 pags., 43 figs. -- This article belongs to the Special Issue Gas Flows in Microsystems, Volume II, Thermometry techniques have been widely developed during the last decades to analyze thermal properties of various fluid flows. Following the increasing interest for microfluidic applications, most of these techniques have been adapted to the microscale and some new experimental approaches have emerged. In the last years, the need for a detailed experimental analysis of gaseous microflows has drastically grown due to a variety of exciting new applications. Unfortunately, thermometry is not yet well developed for analyzing gas flows at the microscale. Thus, the present review aims at analyzing the main currently available thermometry techniques adapted to microflows. Following a rapid presentation and classification of these techniques, the review is focused on optical techniques, which are the most suited for application at microscale. Their presentation is followed by a discussion about their applicability to gas microflows, especially in confined conditions, and the current challenges to be overcome are presented. A special place is dedicated to Raman and molecular tagging thermometry techniques due to their high potential and low intrusiveness., Part of the work from the authors presented in Section 7 has received funding from the European Community’s Seventh Framework Program (FP7/2007-2013) under Grant Agreement No. 215504 and from the European Union’s Framework Programme for Research and Innovation Horizon 2020 (2014–2020) under Marie Skłodowska-Curie Grant Agreement No. 643095. Part of the work from the authors presented in Section 6 has received funding from the Spanish MCIN/AEI/ 10.13039/501100011033 and by “ERDF A way of making Europe” under Grant PID2021-123752NB-I00., Peer reviewed