Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Overcoming stability problems in microwave-assisted heterogeneous catalytic processes affected by catalyst coking

  • Julian, Ignacio
  • Pedersen, Christoffer M.
  • Achkasov, Kostiantyn
  • Hueso, José L.
  • Hellstern, Henrik L.
  • Silva, Hugo
  • Mallada, Reyes
  • Davis, Zachary James
  • Santamaría, Jesús
This article belongs to the Special Issue Microwave-Assisted Catalysis., Microwave-assisted heterogeneous catalysis (MHC) is gaining attention due to its exciting prospects related to selective catalyst heating, enhanced energy-efficiency, and partial inhibition of detrimental side gas-phase reactions. The induced temperature difference between the catalyst and the comparatively colder surrounding reactive atmosphere is pointed as the main factor of the process selectivity enhancement towards the products of interest in a number of hydrocarbon conversion processes. However, MHC is traditionally restricted to catalytic reactions in the absence of catalyst coking. As excellent MW-susceptors, carbon deposits represent an enormous drawback of the MHC technology, being main responsible of long-term process malfunctions. This work addresses the potentials and limitations of MHC for such processes affected by coking (MHCC). It also intends to evaluate the use of different catalyst and reactor configurations to overcome heating stability problems derived from the undesired coke deposits. The concept of long-term MHCC operation has been experimentally tested/applied to for the methane non-oxidative coupling reaction at 700 °C on Mo/ZSM-5@SiC structured catalysts. Preliminary process scalability tests suggest that a 6-fold power input increases the processing of methane flow by 150 times under the same controlled temperature and spatial velocity conditions. This finding paves the way for the implementation of high-capacity MHCC processes at up-scaled facilities., This research was funded by the European Union’s Horizon 2020 Research and Innovation Programme (ADREM project–Grant Agreement no. 680777) and the APC have been waived by the journal., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polyoxometalates as alternative Mo precursors for methane dehydroaromatization on Mo/ZSM-5 and Mo/MCM-22 catalysts

  • Julian, Ignacio
  • Hueso, José L.
  • Lara, Nidya
  • Solé-Daurá, Albert
  • Poblet, Josep M.
  • Mitchell, Scott G.
  • Mallada, Reyes
  • Santamaría, Jesús
The conversion of methane into higher molecular weight hydrocarbons of greater added value has emerged as one of the grand challenges of the 21st century. The non-oxidative methane dehydroaromatization (hereafter MDA) reaction is a promising methane valorisation reaction since it transforms methane into added-value aromatics and olefins, namely benzene, naphthalene and ethylene. Molybdenum-promoted ZSM-5 zeolite has proven to be one of the most effective catalysts for MDA providing a shape-selective environment for the conversion of methane into benzene. However, one of the principle disadvantages of using aluminosilicates in the presence of methane is that the catalyst suffers from rapid deactivation induced by coke formation, which ultimately leads to a decrease in activity and aromatics selectivity, making the process unsuitable for large-scale industrial applications. Better control of the metal dispersion on the surface of the aluminosilicate supports represents a crucial factor to partially suppress catalyst coking and improve stability. Here we show how different molecular polyoxomolybdate (POM) anions can be used as alternative Mo precursors to conventional Mo salts for the preparation of catalysts for the MDA reaction. Molecular dynamics simulations and experimental testing were conducted to characterize the interphase interactions between polyoxomolybdates and zeolite surfaces at the atomistic level and to evaluate the MDA performance of different POM-based catalysts supported on ZSM-5 and MCM-22, respectively. The catalysts prepared using hexamolybdate anions, [Mo6O19]2−, were found to be more active and selective towards benzene than those employing the commercial heptamolybdate, [Mo7O24]6−. The Mo loading and dispersion of MoOx species were found to be the key factors leading to enhanced catalytic stability on ZSM-5 and MCM-22-based supports for MDA where the 5% Mo6/MCM-22 catalyst provided a constant aromatics yield above 7% for more than 18 hours time-on stream operating at 700 °C with a diluted methane flow under atmospheric pressure. The zeolitic catalysts prepared with the Mo6 precursor were found to be amongst the most promising MDA catalysts in the literature and the results of this study pave the way for the selection and use of different POMs as innovative metal precursors to formulate new catalysts and further improve the MDA reaction process., Financial support from the European Union's Horizon 2020 Research and Innovation Programme (ADREM project – Grant Agreement No. 680777) is gratefully acknowledged. The microscopy measurements were conducted at the Laboratorio de Microscopias Avanzadas, Instituto de Nanociencia de Aragon, Universidad de Zaragoza, Spain. The synthesis of the materials has been performed at the Platform of Production of Biomaterials and Nanoparticles of the NANOBIOSIS ICTS, more specifically at the Nanoparticle Synthesis Unit of the CIBER in BioEngineering, Biomaterials & Nanomedicine (CIBER-BBN). JMP thanks the Spanish Ministry of Science (CTQ2017-87269-P), the Generalitat de Catalunya (2017SGR629) and the URV for support. JMP also thanks the ICREA foundation for an ICREA ACADEMIA award., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Supercritical solvothermal synthesis under reducing conditions to increase stability and durability of Mo/ZSM-5 catalysts in methane dehydroaromatization

  • Julian, Ignacio
  • Roedern, Morten B.
  • Hueso, José L.
  • Irusta, Silvia
  • Baden, Ane K.
  • Mallada, Reyes
  • Davis, Zachary James
  • Santamaría, Jesús
Natural gas is currently envisioned as a potential energy and hydrocarbon feedstock in the forthcoming years. To overcome the detrimental flaring of this natural gas and the partial release of its major component, methane, novel and more effective strategies are required. These include the development of new, efficient and seemingly stable catalysts able to rapidly convert methane into valuable feedstocks. We show a novel synthesis method of Mo/ZSM-5 based on a solvothermal synthesis under supercritical conditions and reducing atmosphere (SC-STS-E) to improve metal dispersion and enhance catalyst stability and durability during the methane dehydroaromatization (MDA) reaction. In contrast to the conventional impregnation method, SC-STS-E provides a super-high atom-like metal dispersion at the zeolite pores resulting in the most stable Mo/ZSM-5 catalyst for MDA with the highest long-term hydrocarbon yield (xCH4 = 11.6% and yC2+ = 8.9%, after 15 h on stream) among the catalysts reported in literature for this reaction., Financial support from the European Union’s Horizon 2020 Research and Innovation Programme (ADREM project – Grant Agreement No. 680777) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

From bench scale to pilot plant: A 150x scaled-up configuration of a microwave-driven structured reactor for methane dehydroaromatization

  • Julian, Ignacio
  • Pedersen, Christoffer M.
  • Jensen, Alexander B.
  • Baden, Ane K.
  • Hueso, José L.
  • Friderichsen, Anders V.
  • Birkedal, Henrik
  • Mallada, Reyes
  • Santamaría, Jesús
Microwave-assisted gas-phase conversion on structured catalysts is emerging as a promising process intensification technology in the field of heterogeneous catalysis. The combination of selective heating and structured catalytic materials induces a temperature difference between the heated catalytic sample and the surrounding void regions to avoid non-selective gas-phase reactions. This operational principle allowed inhibiting thermal cracking in alkane dehydrogenation processes as well as retarding catalyst deactivation by coking in methane dehydroaromatization (MDA) processes. However, its effectiveness has not been reported so far out of the laboratory scale conditions. This work addresses the scaling of the microwave-assisted MDA process from lab scale experiments to a scaled-up configuration capable of stable operation with a 150-fold higher feeding rate. The scaling-up potential and main obstacles to overcome for this technology are critically discussed. In addition, a techno-economic assessment of the MW-MDA process is presented. The catalytic activity was kept for seven consecutive reaction cycles, i.e. 35 h MW-MDA, prior to a progressive decay due to permanent deactivation caused by zeolite dealumination and active metal loss. The scaled set-up operated for up to 295 consecutive hours under unmanned operation conducting 4 -h MDA-regeneration cycles on Mo/ZSM-5@SiC monoliths and resulting in 125-fold increase of converted methane and a 450-fold increase of benzene (0.17 LC6H6/h) in comparison with the laboratory scale tests. Scaled set-up experiments were run using only a 6-fold microwave input power, thus, highlighting the non-linearity between energy consumption and scaling factor for this technology and the importance of microwave cavity design., Financial support from the European Union’s Horizon 2020 Research and Innovation Programme (ADREM project – Grant Agreement No. 680777) is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Gas-solid contactors and catalytic reactors with direct microwave heating: Current status and perspectives

  • Hueso, José L.
  • Mallada, Reyes
  • Santamaría, Jesús
Microwave heating (MWH) transforms energy from an electromagnetic wave to heat. In contrast to conventional heating (CH) mechanisms that use slower heat transfer processes via conduction, convection or radiation, microwaves (MW) directly interact with MW susceptor materials and induce a rapid conversion of the electromagnetic energy into heat. This rapid heating provides MWH with distinct features that can be leveraged to increase conversion, selectivity and/or energy efficiency of chemical processes. Here we discuss recent significant advances reported in MWH processes involving gas-solid interactions. Special attention is devoted to key aspects such as the methodologies to accurately determine local temperatures under the influence of electromagnetic (EM). Other relevant aspects such as the consideration of the solid catalyst dielectric properties or the design of novel gas-solid contactor configurations will be discussed. Emerging aspects such as the potential of MWH to minimize secondary by-products in high temperature reactions or to efficiently perform in transient processes, e.g. adsorption-desorption cycles, are highlighted. Finally, current challenges and perspectives towards a wide application of MWH in gas solid contactors will be critically discussed., Financial support from the European Research Council Advanced Grant (HECTOR-267626) and the Regional Government of Aragon (DGA) is gratefully acknowledged. Financial support from the European Union’s Horizon 2020 Research and Innovation Programme (ADREM project – Grant Agreement No. 680777) is also gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Non-oxidative methane conversion in microwave-assisted structured reactors

  • Julian, Ignacio
  • Ramirez, Heidy
  • Hueso, José L.
  • Mallada, Reyes
  • Santamaría, Jesús
The main problem to be addressed in the valorization of methane under non-oxidative conditions (MNOC) is to reduce or even avoid coke formation. In this work we report the use of microwave-assisted heating for MNOC. We have developed a system able to heat-up a Mo-ZSM5 catalyst coated on silicon carbide monolith that could operate stable for at least 19 h at reaction conditions, 700 °C. We demonstrate that under MW-heating the selectivity shifts to C2s and benzene. In contrast, the operation under conventional heating (CH) produces more coke and polyaromatics. The selective microwave heating has two effects in this reaction: i) during the activation of the catalyst the formation of the active catalytic species of Mo2C inside the microporous support is different affecting the selectivity and product distribution; ii) a gas-solid temperature gradient is established that prevents the formation of coke from PAHs in the gas phase. The MNOC process under controlled MW heating at high space velocity (3000 mL/gcat·h) gives a hydrocarbon yield of around 6% with a very low deactivation rate. These results open up new possibilities for process intensification using alternative sources of energy, as is the case of microwaves, for heating structured catalytic reactors., Financial support from the European Union’s Horizon 2020 Research and Innovation Programme (ADREM project – Grant Agreement No. 680777) is gratefully acknowledged. The microscopy measurements were conducted at the Laboratorio de Microscopias Avanzadas, Instituto de Nanociencia de Aragon, Universidad de Zaragoza, Spain., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Non-oxidative methane conversion in microwave-assisted structured reactors

  • Julian, Ignacio
  • Ramirez, Heidy
  • Hueso, Jose L.
  • Mallada, Reyes
  • Santamaria, Jesus
The main problem to be addressed in the valorization of methane under non-oxidative conditions (MNOC) is to reduce or even avoid coke formation. In this work we report the use of microwave-assisted heating for MNOC. We have developed a system able to heat-up a Mo-ZSM5 catalyst coated on silicon carbide monolith that could operate stable for at least 19¿h at reaction conditions, 700°C. We demonstrate that under MW-heating the selectivity shifts to C2s and benzene. In contrast, the operation under conventional heating (CH) produces more coke and polyaromatics. The selective microwave heating has two effects in this reaction: i) during the activation of the catalyst the formation of the active catalytic species of Mo2C inside the microporous support is different affecting the selectivity and product distribution; ii) a gas-solid temperature gradient is established that prevents the formation of coke from PAHs in the gas phase. The MNOC process under controlled MW heating at high space velocity (3000¿mL/gcat·h) gives a hydrocarbon yield of around 6% with a very low deactivation rate. These results open up new possibilities for process intensification using alternative sources of energy, as is the case of microwaves, for heating structured catalytic reactors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Overcoming stability problems in microwave-assisted heterogeneous catalytic processes affected by catalyst coking

  • Julian I.
  • Pedersen C.M.
  • Achkasov K.
  • Hueso J.L.
  • Hellstern H.L.
  • Silva H.
  • Mallada R.
  • Davis Z.J.
  • Santamaria J.
Microwave-assisted heterogeneous catalysis (MHC) is gaining attention due to its exciting prospects related to selective catalyst heating, enhanced energy-efficiency, and partial inhibition of detrimental side gas-phase reactions. The induced temperature difference between the catalyst and the comparatively colder surrounding reactive atmosphere is pointed as the main factor of the process selectivity enhancement towards the products of interest in a number of hydrocarbon conversion processes. However, MHC is traditionally restricted to catalytic reactions in the absence of catalyst coking. As excellent MW-susceptors, carbon deposits represent an enormous drawback of the MHC technology, being main responsible of long-term process malfunctions. This work addresses the potentials and limitations of MHC for such processes affected by coking (MHCC). It also intends to evaluate the use of different catalyst and reactor configurations to overcome heating stability problems derived from the undesired coke deposits. The concept of long-term MHCC operation has been experimentally tested/applied to for the methane non-oxidative coupling reaction at 700¿C on Mo/ZSM-5@SiC structured catalysts. Preliminary process scalability tests suggest that a 6-fold power input increases the processing of methane flow by 150 times under the same controlled temperature and spatial velocity conditions. This finding paves the way for the implementation of high-capacity MHCC processes at up-scaled facilities.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Polyoxometalates as alternative Mo precursors for methane dehydroaromatization on Mo/zsm-5 and Mo/mcm-22 catalysts

  • Julián, Ignacio
  • Hueso, José L.
  • Lara, Nidya
  • Sole-Daura, Albert
  • Poblet, Josep M.
  • Mitchell, Scott G.
  • Mallada, Reyes
  • Santamaría, Jesús
The conversion of methane into higher molecular weight hydrocarbons of greater added value has emerged as one of the grand challenges of the 21st century. The non-oxidative methane dehydroaromatization (hereafter MDA) reaction is a promising methane valorisation reaction since it transforms methane into added-value aromatics and olefins, namely benzene, naphthalene and ethylene. Molybdenum-promoted ZSM-5 zeolite has proven to be one of the most effective catalysts for MDA providing a shape-selective environment for the conversion of methane into benzene. However, one of the principle disadvantages of using aluminosilicates in the presence of methane is that the catalyst suffers from rapid deactivation induced by coke formation, which ultimately leads to a decrease in activity and aromatics selectivity, making the process unsuitable for large-scale industrial applications. Better control of the metal dispersion on the surface of the aluminosilicate supports represents a crucial factor to partially suppress catalyst coking and improve stability. Here we show how different molecular polyoxomolybdate (POM) anions can be used as alternative Mo precursors to conventional Mo salts for the preparation of catalysts for the MDA reaction. Molecular dynamics simulations and experimental testing were conducted to characterize the interphase interactions between polyoxomolybdates and zeolite surfaces at the atomistic level and to evaluate the MDA performance of different POM-based catalysts supported on ZSM-5 and MCM-22, respectively. The catalysts prepared using hexamolybdate anions, [Mo6O19]2-, were found to be more active and selective towards benzene than those employing the commercial heptamolybdate, [Mo7O24]6-. The Mo loading and dispersion of MoOx species were found to be the key factors leading to enhanced catalytic stability on ZSM-5 and MCM-22-based supports for MDA where the 5% Mo6/MCM-22 catalyst provided a constant aromatics yield above 7% for more than 18 hours time-on stream operating at 700 °C with a diluted methane flow under atmospheric pressure. The zeolitic catalysts prepared with the Mo6 precursor were found to be amongst the most promising MDA catalysts in the literature and the results of this study pave the way for the selection and use of different POMs as innovative metal precursors to formulate new catalysts and further improve the MDA reaction process.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

From bench scale to pilot plant: A 150x scaled-up configuration of a microwave-driven structured reactor for methane dehydroaromatization

  • Julian, I.
  • Pedersen, C.M.
  • Jensen, A.B.
  • Baden, A.K.
  • Hueso, J.L.
  • Friderichsen, A.V.
  • Birkedald, H.
  • Mallada, R.
  • Santamaria, J.
Microwave-assisted gas-phase conversion on structured catalysts is emerging as a promising process intensifi-cation technology in the field of heterogeneous catalysis. The combination of selective heating and structured catalytic materials induces a temperature difference between the heated catalytic sample and the surrounding void regions to avoid non-selective gas-phase reactions. This operational principle allowed inhibiting thermal cracking in alkane dehydrogenation processes as well as retarding catalyst deactivation by coking in methane dehydroaromatization (MDA) processes. However, its effectiveness has not been reported so far out of the lab-oratory scale conditions. This work addresses the scaling of the microwave-assisted MDA process from lab scale experiments to a scaled-up configuration capable of stable operation with a 150-fold higher feeding rate. The scaling-up potential and main obstacles to overcome for this technology are critically discussed. In addition, a techno-economic assessment of the MW-MDA process is presented. The catalytic activity was kept for seven consecutive reaction cycles, i.e. 35 h MW-MDA, prior to a progressive decay due to permanent deactivation caused by zeolite dealumination and active metal loss. The scaled set-up operated for up to 295 consecutive hours under unmanned operation conducting 4 -h MDA-regeneration cycles on Mo/ZSM-5@SiC monoliths and resulting in 125-fold increase of converted methane and a 450-fold increase of benzene (0.17 LC6H6/h) in comparison with the laboratory scale tests. Scaled set-up experiments were run using only a 6-fold microwave input power, thus, highlighting the non-linearity between energy consumption and scaling factor for this tech-nology and the importance of microwave cavity design.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Supercritical solvothermal synthesis under reducing conditions to increase stability and durability of Mo/ZSM-5 catalysts in methane dehydroaromatization

  • Julian, Ignacio
  • Roedern, Morten B.
  • Hueso, Jose L.
  • Irusta, Silvia
  • Badend, Ane K.
  • Mallada, Reyes
  • Davis, Zachary
  • Santamaria, Jesus
Natural gas is currently envisioned as a potential energy and hydrocarbon feedstock in the forthcoming years. To overcome the detrimental flaring of this natural gas and the partial release of its major component, methane, novel and more effective strategies are required. These include the development of new, efficient and seemingly stable catalysts able to rapidly convert methane into valuable feedstocks. We show a novel synthesis method of Mo/ZSM-5 based on a solvothermal synthesis under supercritical conditions and reducing atmosphere (SC-STSE) to improve metal dispersion and enhance catalyst stability and durability during the methane dehydroaromatization (MDA) reaction. In contrast to the conventional impregnation method, SC-STS-E provides a superhigh atom-like metal dispersion at the zeolite pores resulting in the most stable Mo/ZSM-5 catalyst for MDA with the highest long-term hydrocarbon yield (xCH4=11.6% and yC2+ = 8.9%, after 15 h on stream) among the catalysts reported in literature for this reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Gas-solid contactors and catalytic reactors with direct microwave heating: current status and perspectives

  • Hueso, José L.
  • Mallada, Reyes
  • Santamaría, Jesús
Microwave heating (MWH) transforms energy from an electromagnetic wave to heat. In contrast to conventional heating (CH) mechanisms that use slower heat transfer processes via conduction, convection or radiation, microwaves (MW) directly interact with MW susceptor materials and induce a rapid conversion of the electromagnetic energy into heat. This rapid heating provides MWH with distinct features that can be leveraged to increase conversion, selectivity and/or energy efficiency of chemical processes. Here we discuss recent significant advances reported in MWH processes involving gas-solid interactions. Special attention is devoted to key aspects such as the methodologies to accurately determine local temperatures under the influence of electromagnetic (EM). Other relevant aspects such as the consideration of the solid catalyst dielectric properties or the design of novel gas-solid contactor configurations will be discussed. Emerging aspects such as the potential of MWH to minimize secondary by-products in high temperature reactions or to efficiently perform in transient processes, e.g. adsorption-desorption cycles, are highlighted. Finally, current challenges and perspectives towards a wide application of MWH in gas solid contactors will be critically discussed.