Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of activation conditions on textural properties and performance of activated biochars for pyrolysis vapors upgrading

  • Di Stasi, Christian
  • Greco, Gianluca
  • Canevesi, Rafael L. S.
  • Izquierdo Pantoja, María Teresa
  • Fierro, Vanessa
  • Celzard, Alain
  • González García, Belén
  • Manyà, Joan J.
8 figures, 4 tables. supplementary information avilable.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0, The main aim of the present study is to provide a comprehensive assessment of the effects of process activation conditions on the textural properties of the resulting activated carbons, which were produced from wheat straw-derived biochar through chemical activation (with K2CO3 at different pressures and mass impregnation ratios) and physical activation (with CO2 at different temperatures and pressures). For chemically activated biochars, it was found that specific surface area and pore size distribution were both only positively affected by increasing the carbonate loading. However, physically activated biochars produced at the highest pressure and lowest temperature (1.0 MPa and 700 °C) had the highest surface areas and widest pore size distributions. The materials with the most appropriate textural properties were then tested as catalysts for steam and dry reforming of the aqueous phase of pyrolysis oil. The best catalytic performance (a total gas yield of 74% and a selectivity toward H2 of almost 40%) was observed for a physically activated biochar. This good performance was ascribed to the high availability of K0 on the catalyst surface, which could effectively promote the reactions involved in the upgrading process., This project received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 721991. The authors also acknowledge the funding from the Aragón Government (Ref. T22_20R), co-funded by FEDER 2014-2020 “Construyendo Europa desde Aragón”. This study was partly supported by the French PIA project “Lorraine Université d’Excellence”, reference ANR-15-IDEX-04-LUE, PROMOTEE project and TALiSMAN project, funded by FEDER (2019-000214)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Importance of pyrolysis temperature and pressure in the concentration of polycyclic aromatic hydrocarbons in wood waste-derived biochars

  • Greco, Gianluca
  • Videgain, María
  • Di Stasi, Christian
  • Pires, Elísabet
  • Manyà, Joan J.
Biochar addition to soil can lead to potential environmental risks due to its content of polycyclic aromatic hydrocarbons (PAHs). Until now, previous research focused on assessing the influence of pyrolysis peak temperature and feedstock on the formation and evolution of PAHs. Nevertheless, the effects of other important process parameters —such as pressure, gas residence time, and type of carrier gas— have not been comprehensively explored. To fill this gap, a 2-level full factorial design of experiments was conducted to assess the influence of the above-mentioned parameters on the pyrolysis behavior of an untreated wood waste as well as the properties of resulting biochars, including their PAHs contents. Results showed that the highest production of PAHs was reached at lower peak temperatures, whereas an increase in temperature led to a substantial reduction of the final PAHs content. An increased pressure also resulted in a marked decrease in PAHs, probably as a consequence of the higher carrier gas flow rates used under pressurized conditions, which could inhibit the generation of PAHs by condensation and polymerization. The outstanding results obtained from the phytotoxicity assessment for three plant species (barley, watercress, and basil) suggest that PAHs were not the major responsible for the observed short-term phytotoxic effects of biochars, since a considerable part of the phytotoxic compounds in biochar can be removed by a simple water washing step., This project has received funding from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No 721991. JJM and EP also acknowledge the funding from the Aragón Government (Refs. T22_20R and E37_20R, respectively), co-funded by FEDER 2014-2020 “Construyendo Europa desde Aragón”. EP acknowledges the Spanish Ministerio de Ciencia, Innovación y Universidades (project number RTI2018-093431-B-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of the effects of process water recirculation on the surface chemistry and morphology of hydrochar

  • Arauzo, Pablo
  • Olszewski, Maciej Pawel
  • Wang, Xia
  • Pfersich, Jens
  • Sebastián, Víctor
  • Manyà, Joan J.
  • Hedin, Niklas
  • Kruse, Andrea
The effect of two process water (PW) recirculation strategies after hydrothermal carbonization (HTC) of brewers spent grains (BSG) is evaluated with the focus on the hydrochar characteristics. The HTC process has been carried out under different operating conditions, which are residence time between 2 and 4 h and temperature in the range of 200–220 °C. The composition of the hydrochars reveals that operating conditions have a more significant effect than PW recirculation. The composition of the liquid produced by HTC with PW recirculation is essentially controlled by the operating temperature, for instance, the total organic carbon (TOC) in the PW changes in the narrow range of 200–220 °C. A detailed analysis of PW also has been done. The main components of the liquid phase are lactic, formic, acetic, levulinic, and propionic acid as well as 5-hydroxymethylfurfural, that affect the surface structure of the hydrochars., This research was funded by the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie Grant Agreement No. 721991 and Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) – 328017493/GRK 2366 (International Research Training Group “Adaption of maize-based food-feed-energy systems to limited phosphate resources”)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Combustion characteristics of hydrochar and pyrochar derived from digested sewage sludge

  • Arauzo, P.J.
  • Atienza-Martínez, M.
  • Ábrego, J.
  • Olszewski, M.P.
  • Cao, Z.
  • Kruse, A.
In this paper, hydrochars and pyrochars were produced at 260 ºC under different residence times (2 and 4 h) using anaerobic digested sewage sludge (SSL) as initial feedstock. The effect of reaction time on the fuel properties of hydrochars and pyrochars was evaluated. Moreover, the combustion kinetics of raw SSL and the derived pyrochars and hydrochars without coal blending were determined at two different air flows (20 and 90 mL/min) and compared. In the same conditions, the yield of hydrochar was significantly lower than that of pyrochar, confirming the different reaction pathways followed in each process. The results showed hydrochars have lower carbon recovery and energy yield than pyrochars, making the latter more suitable for energy purposes. The thermogravimetric combustion study showed that both thermochemical treatments increased the ignition temperature but decreased the burnout temperature, which results in higher stability during handling and storage. However, raw SSL is better for combustion than hydrochar according to the combustibility index. In addition, the kinetic study showed that the activation energy of the combustion of biochars, especially pyrochar, is lower than that of raw SSL, which is advantageous for their combustion.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Physically activated wheat straw-derived biochar for biomass pyrolysis vapors upgrading with high resistance against coke deactivation

  • Di Stasi, Christian
  • Alvira, Darío
  • Greco, Gianluca
  • González, Belén
  • Manya, Joan J.
Wheat straw-derived biochars (produced through slow pyrolysis at 500 degrees C and 0.1 MPa) were physically (with CO2) and chemically (with K2CO3) activated to assess their performance as renewable and low-cost catalysts for biomass pyrolysis vapors upgrading. Preliminary cracking experiments, which were carried out at 700 degrees C using a mixture of four representative model compounds, revealed a clear correlation between the volume of micropores of the catalyst and the total gas production, suggesting that physical activation up to a degree of burn-off of 40% was the most interesting activation route. Next, steam reforming experiments were conducted using the most microporous material to analyze the effect of both the bed temperature and gas hourly space velocity (GHSV) on the total gas production. The results showed a strong dependence between the bed temperature and the total gas production, with the best result obtained at the highest temperature (750 degrees C). On the other hand, the change in GHSV led to minor changes in the total gas yield, with a maximum achieved at 14500 h(-1). Under the best operating conditions deduced in the previous stages, the addition of CO2 into the feed gas stream (partial pressure of 20 kPa) resulted in a total gas production of 98% with a H-2/CO molar ratio of 2.16. This good result, which was also observed during the upgrading of the aqueous phase of a real biomass pyrolysis oil, was ascribed to the relatively high coke gasification rate, which refresh the active surface area preventing deactivation by coke deposition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effects of slow-pyrolysis conditions on the products yields and properties and on exergy efficiency: A comprehensive assessment for wheat straw

  • Greco, Gianluca
  • Di Stasi, Christian
  • Rego, Filipe
  • González, Belén
  • Manyà, Joan J.
In the present work, the effects of the peak temperature (400–550 °C), absolute pressure (0.2–0.9 MPa), gas residence time (100–200 s) and reactor atmosphere (pure N2 or a mixture of CO2/N2) on the pyrolysis behavior of wheat straw pellets were investigated. A factorial design of experiments was adopted to assess the effects of the above-mentioned factors on the pyrolysis products, the exergy efficiencies related to them and to the overall process, and the heat required. The pyrolysis energy/exergy assessment is nowadays of great interest, for the scaling of the installations from lab-scale to commercial-scale. Results showed that, as expected, the peak temperature was the most influential factor on the yields and distributions of all the pyrolysis products as well as the char properties related to its potential stability and pore size distribution. However, an increased pressure enhanced the release of the gas species at the expense of the liquid products, without altering the final char yield. The char exergy efficiency was negatively affected by an increase in peak temperature, whereas its effect on the exergy efficiency of the produced gas resulted to be positive. It was also found that pressurized pyrolysis favored the exergy efficiency of the process, even at relatively high pyrolysis peak temperature. For the biomass feedstock and the range of operating conditions studied here, thermodynamic irreversibilities of the pyrolysis system were considerably lowered when the process was conducted at 550 °C, 0.9 MPa and using a mixture of CO2 and N2 as carrier gas at relatively short residence times.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Importance of pyrolysis temperature and pressure in the concentration of polycyclic aromatic hydrocarbons in wood waste-derived biochars

  • Greco, Gianluca
  • Videgain, María
  • Di Stasi, Christian
  • Pires, Elisabet
  • Manyà, Joan J.
Biochar addition to soil can lead to potential environmental risks due to its content of polycyclic aromatic hydrocarbons (PAHs). Until now, previous research focused on assessing the influence of pyrolysis peak temperature and feedstock on the formation and evolution of PAHs. Nevertheless, the effects of other important process parameters —such as pressure, gas residence time, and type of carrier gas— have not been comprehensively explored. To fill this gap, a 2-level full factorial design of experiments was conducted to assess the influence of the above-mentioned parameters on the pyrolysis behavior of an untreated wood waste as well as the properties of resulting biochars, including their PAHs contents. Results showed that the highest production of PAHs was reached at lower peak temperatures, whereas an increase in temperature led to a substantial reduction of the final PAHs content. An increased pressure also resulted in a marked decrease in PAHs, probably as a consequence of the higher carrier gas flow rates used under pressurized conditions, which could inhibit the generation of PAHs by condensation and polymerization. The outstanding results obtained from the phytotoxicity assessment for three plant species (barley, watercress, and basil) suggest that PAHs were not the major responsible for the observed short-term phytotoxic effects of biochars, since a considerable part of the phytotoxic compounds in biochar can be removed by a simple water washing step.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Wheat-straw-derived activated biochar as a renewable support of Ni-CeO2 catalysts for CO2 methanation

  • Di Stasi C.
  • Renda S.
  • Greco G.
  • González B.
  • Palma V.
  • Manyà J.J.
Ceria-and urea-doped activated biochars were used as support for Ni-based catalysts for CO2 methanation purposes. Different materials were prepared and tested to find the best catalytic formulation. After several CO2 methanation experiments—carried out at 0.35–1.0 MPa and 300–500¿C—it was found that the most suitable catalyst was a wheat-straw-derived activated biochar loaded with 30 wt.% of CeO2 and 20 wt.% of Ni. Using this catalyst, a CO2 conversion of 65% with a CH4 selectivity of 95% was reached at 1.0 MPa, 400¿C, and 13, 200 h-1 . From the study of the influence of the gas hourly space velocity, it was deduced that the most likely reaction mechanism was a reverse water–gas shift reaction, followed by CO hydrogenation. N-doping of the carbon support as an alternative to the use of ceria was also investigated. However, both CO2 conversion and selectivity toward CH4 values were clearly lower than those obtained for the ceria-containing catalyst cited above. The outcomes of this work indicate that a renewable biomass-derived support can be effectively employed in the catalytic conversion of CO2 to methane. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Biomass-derived carbons physically activated in one or two steps for CH4/CO2 separation

  • Greco, G.
  • Canevesi, R.L.S.
  • Di Stasi, C.
  • Celzard, A.
  • Fierro, V.
  • Manyà Cervelló, J. J.
The present study aims at evaluating the suitability of producing activated carbons (ACs) derived from wheat straw by a one-step synthesis approach, as an alternative to more conventional two steps production processes (i.e., pyrolysis and subsequent activation). The performance of the produced ACs, in one or two steps, as sustainable and selective CO2 adsorbents for CH4/CO2 separation is compared. In addition, the influence of pyrolysis conditions on the properties of the resulting two-step ACs is carefully analyzed. We show that the biochar-based precursors of ACs presenting the best textural properties were obtained under mild conditions of maximum temperature and absolute pressure during pyrolysis. The one-step ACs were fully comparable —in terms of textural properties as well as CO2 uptake and selectivity— to those produced by the more conventional two-step synthesis process. In addition, results obtained from breakthrough curve simulations highlight that the best AC in terms of CH4 recovery under dynamic conditions was produced by a one-step activation. Therefore, the one-step process appears to be as an attractive route for the production of engineered carbon materials, which can lead to significant cost savings in large-scale production systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Part 1-Impact of Pyrolysis Temperature and Wood Particle Length on Vapor Cracking and Char Porous Texture in Relation to the Tailoring of Char Properties

  • Maziarka, Przemyslaw
  • Kienzl, Norbert
  • Dieguez-Alonso, Alba
  • Fierro, Vanessa
  • Celzard, Alain
  • Arauzo, Pablo J.
  • Hedin, Niklas
  • Prins, Wolter
  • Anca-Couce, Andrés
  • Manyà, Joan J.
  • Ronsse, Frederik
Pore size distribution is a key parameter in the performance of biobased pyrolytic char in novel applications. In industrial-scale production, the size of feedstock particles typically exceeds a few millimeters. For such particle sizes, it is a challenge to tailor the final properties of the char based only on the process conditions (experimental and modeling-wise). Pyrolysis studies of single particles larger than a few millimeters provide data sets useful for modeling and optimization of the process. Part 1 of this research focused on the pyrolysis of single particles of beech wood, secondary cracking, and its effect on the char porous texture. It contains a quantitative assessment of the effects of five conversion temperatures (from 300 to 840 °C) and two particle dimensions (Ø8 × 10 mm and Ø8 × 16 mm) on the composition of the pyrolysis vapors and pore morphology of the char. Results from real-time temperature and mass changes are presented along with release profiles of 15 vapor constituents measured by infrared spectroscopy. Furthermore, characterization of the collected bio-oil (using GC-MS/FID) and the textural hierarchical structured char (through N2 and CO2 adsorption, Hg porosimetry, and scanning electron microscopy (SEM)) was performed. Cracking of vapors above 500 °C was compound-specific. The polyaromatic hydrocarbons (PAHs) yield, between 680 and 840 °C, increased 5 times for 10 mm particles and 9 times for 16 mm ones. Besides temperature, PAH yield was suspected to correlate with particle length and PAHs/soot deposition in the micropores. Results showed that the macropores accounted for over 80% of the total pore volume, regardless of the temperature and particle length. Increasing the particle length by 60% caused a reduction in the specific surface area (ca. 15% at 840 °C) of the resulting char, mainly due to a reduction in microporosity. Based on the findings, the production conditions for a specific char application are suggested. The obtained data will be used in Part 2 of this research, devoted to subsequent CFD modeling of the process.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Part 2 - Tailoring of pylolytic char properties with a single particle CFD model with a focus on the impact of shrinking, vapor cracking, and char permeability

  • Maziarka, Przemyslaw
  • Kienz, Norbert
  • Dieguez-Alonso, Alba
  • Prins, Wolter
  • Arauzo, Pablo J.
  • Skreiberg, Øyvind
  • Anca-Couce, Andrés
  • Manyà, Joan J.
  • Ronsse, Frederik
The prediction of the structural properties of biobased carbonaceous materials of pyrolytic origin (chars) with only base feedstock properties and process conditions still poses a challenge that hinders char tailoring for novel applications. CFD modeling of single biomass particle conversion can help solve this issue since it allows for the quantification of relations between parameters that are difficult to measure. A model for char tailoring must include a validated representation of the structural changes coupled to all other relevant phenomena occurring during conversion. Part 2 of this study focuses on finding the description of the mentioned aspects to achieve the highest precision of prediction of the structural changes in char by a CFD model. The investigation in Part 2 is composed of three cases focused on accurate description and prediction of (1) bulk density and porosity, (2) secondary vapor reactions on yields and soot formation, and (3) permeability, as well as the outflux and conversion of evolved vapors. The experimental results from Part 1 and the literature data were used to find appropriate descriptions of phenomena and assess the accuracy of the model. The model results indicate that for both particle lengths (10 and 16 mm), a high accuracy of prediction of base structural parameters was achieved. The average prediction error for temperatures between 400 and 840 °C of bulk density was 31 ± 15 kg/m3, and the porosity was 1.8 ± 1.1 vol %. The results also show a low error in the prediction of bulk product yields (dry basis) over the mentioned temperature range, which were: for char 2.8 ± 1.1 wt %, for the condensable fraction 6.5 ± 3.3 wt %, and for the pyrolysis gas 4.1 ± 1.9 wt %. The distribution of secondary char formation was found to be nonuniform below 500 °C. The changes in permeability had a minor influence on the vapor outflux but a non-negligible effect on the soot formation, especially at 840 °C. The results indicate a need for further improvement of the primary degradation model to increase the accuracy of the effect of soot formation on the char structure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Optimization of the operating conditions for steam reforming of slow pyrolysis oil over an activated biochar-supported Ni–Co catalyst

  • Di Stasi, C.
  • Cortese, M.
  • Greco, G.
  • Renda, S.
  • González, B.
  • Palma, V.
  • Manyà, J.J.
Highly performing activated biochar-based catalysts were produced for steam reforming of slow pyrolysis oil. The raw biochar obtained from the slow pyrolysis step was physically activated with CO2 at 700 °C and 1.0 MPa and then employed as support. Preliminary tests on steam reforming of acetic acid at 600 °C showed that using activated biochar-supported catalysts containing 10 wt % Ni and 7 wt % Co led to a conversion above 90% with a relatively slow deactivation rate. When a representative organic model compounds mixture was used as feed, relatively fast deactivation of the catalyst was observed, probably due to the adsorption of heavy organic compounds, which could subsequently react to form not easily desorbable reaction intermediates. However, the dual Ni–Co catalysts exhibited a good performance during the steam reforming of a real slow pyrolysis oil at 750 °C, showing long stability and a constant carbon conversion of 65%.