Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Experimental and Numerical Study of the Thermo-Fluid Dynamics of Borehole Heat Exchangers Incorporating Advanced Materials to be Optimized for use as Thermal Energy Storage (BTES)

  • Javadi, Hossein|||0000-0002-2059-7145
[ES] El sistema de bomba de calor geotérmica (GSHP) es una tecnología prometedora para utilizar la energía geotérmica somera (EGS). En este sistema, un intercambiador enterrado de calor de perforación (BHE) desempeña un papel principal e influye directamente en el coeficiente de rendimiento estacional (SCOP) de este sistema geotérmico poco profundo. Se han llevado a cabo diferentes estudios para mejorar el rendimiento del BHE, incluyendo el uso de materiales avanzados para el plástico de las tuberías, uso de fluido caloportador (o de transferencia de calor) y de relleno/grouting, de mayor transferencia de calor, diseño de nuevas geometrías, y la optimización del BHE para ser utilizado como sistemas de almacenamiento de energía térmica (BTES). Los costes de perforación, el consumo eléctrico de las bombas de calor y la resistencia térmica de las perforaciones pueden reducirse utilizando materiales con propiedades termofísicas adecuadas, como los nanofluidos y los materiales de almacenamiento térmico. De este modo, no sólo se produce una transferencia de calor más significativa entre el fluido caloportador, el relleno y el terreno, sino que también se reduce el efecto térmico sobre el entorno. El fluido de transferencia de calor es uno de los factores de optimización de la BHE que se utilizará para el almacenamiento de energía térmica (TES). Una mayor conductividad térmica en el fluido de transferencia de calor mejora la eficacia de la transferencia de calor entre el fluido y los materiales alrededor, lo que lleva a alcanzar con mayor rapidez la temperatura de cambio de fase en los materiales de almacenamiento. Cuando se usa un fluido de transferencia de calor con una conductividad térmica superior, la temperatura del material de almacenamiento de calor experimenta fluctuaciones más rápidas, lo que reduce significativamente la duración necesaria para un cambio de fase completo. Además, usar materiales de cambio de fase (PCM) para almacenar calor en lugar del relleno convencional permite aprovechar el BHE como sistema BTES. Además de disminuir considerablemente la profundidad de perforación necesaria, el sistema BTES puede almacenar y liberar energía diaria y estacionalmente para reducir la carga durante las horas punta. Sin embargo, hay un vacío notable en la bibliografía sobre la exploración y aplicación de nuevos materiales de almacenamiento de calor y fluidos de transferencia de calor en las BHE para hacerlas aptas para fines de BTES. Aunque se han aplicado diversas innovaciones para mejorar el rendimiento de los BHE, como el uso de materiales plásticos avanzados y la optimización del diseño, la mayor parte de la investigación se ha centrado en el uso convencional de los BHE. Debería prestarse más atención a las ventajas potenciales del aprovechamiento de los intercambiadores de calor mediante la aplicación de nanofluidos y PCM como fluidos de transferencia de calor y medios de almacenamiento de calor, respectivamente. Como ya se ha mencionado, estos materiales poseen propiedades termofísicas superiores que pueden dar lugar a una transferencia de calor más eficiente, una reducción de los costes de perforación, un menor consumo de electricidad en las bombas de calor y una disminución de la resistencia térmica de la perforación. Esta laguna en la investigación hace necesaria una investigación en profundidad para determinar la viabilidad y factibilidad de la aplicación de estos materiales avanzados en las BHE, facilitando en última instancia su transformación en sistemas BTES fiables. Por lo tanto, los principales objetivos de esta tesis doctoral son estudiar experimental y numéricamente los impactos del uso de materiales avanzados para el fluido caloportador y el relleno/grouting tales como nanofluidos y PCMs, en el rendimiento del BHE como sistemas BTES. El estudio pretende seleccionar los materiales más favorables, convirtiéndose en una referencia práctica y fiable para futuros proyectos y sectores industriales., [CA] El sistema de bomba de calor geotèrmica (GSHP, en anglès) és una tecnologia prometedora per a utilitzar l'energia geotèrmica succinta (EGS). En este sistema, un bescanviador enterrat de calor de perforació (BHE, en anglès) exercix un paper principal i influïx directament en el coeficient de rendiment estacional (SCOP) d'este sistema geotèrmic poc profund. S'han dut a terme diferents estudis per a millorar el rendiment del *BHE, incloent-hi l'ús de materials avançats per al plàstic de les canonades, ús de fluid termòfor (o de transferència de calor) i de grouting, de major transferència de calor, disseny de noves geometries, i l'optimització del BHE per a ser utilitzat com a sistemes d'emmagatzematge d'energia tèrmica (BTES, en anglès). Els costos de perforació, el consum elèctric de les bombes de calor i la resistència tèrmica de les perforacions poden reduir-se utilitzant materials amb propietats termo-físiques adequades, com els nanofluids i els materials d'emmagatzematge tèrmic. D'esta manera, no sols es produïx una transferència de calor més significativa entre el fluid termòfor, el farciment i el terreny, sinó que també es reduïx l'efecte tèrmic sobre l'entorn. El fluid de transferència de calor és un dels factors d'optimització de la *BHE que s'utilitzarà per a l'emmagatzematge d'energia tèrmica (*TES). Una major conductivitat tèrmica en el fluid de transferència de calor millora l'eficàcia de la transferència de calor entre el fluid i els materials al voltant, la qual cosa porta a aconseguir amb major rapidesa la temperatura de canvi de fase en els materials d'emmagatzematge. Quan s'usa un fluid de transferència de calor amb una conductivitat tèrmica superior, la temperatura del material d'emmagatzematge de calor experimenta fluctuacions més ràpides, la qual cosa reduïx significativament la duració necessària per a un canvi de fase complet. A més, usar materials de canvi de fase (PCM, en anglès) per a emmagatzemar calor en lloc del farciment convencional permet aprofitar el BHE com a sistema BTES. A més de disminuir considerablement la profunditat de perforació necessària, el sistema BTES pot emmagatzemar i alliberar energia diària i estacionalment per a reduir la càrrega durant les hores punta. No obstant això, hi ha un buit notable en la bibliografia sobre l'exploració i aplicació de nous materials d'emmagatzematge de calor i fluids de transferència de calor en les BHE per a fer-les aptes per a fins de BTES. Encara que s'han aplicat diverses innovacions per a millorar el rendiment dels BHE, com l'ús de materials plàstics avançats i l'optimització del disseny, la major part de la investigació s'ha centrat en l'ús convencional dels BHE. Hauria de prestar-se més atenció als avantatges potencials de l'aprofitament dels bescanviadors de calor mitjançant l'aplicació de nanofluids i PCM com a fluids de transferència de calor i mitjans d'emmagatzematge de calor, respectivament. Com ja s'ha esmentat, estos materials posseïxen propietats termo-físiques superiors que poden donar lloc a una transferència de calor més eficient, una reducció dels costos de perforació, un menor consum d'electricitat en les bombes de calor i una disminució de la resistència tèrmica de la perforació. Esta llacuna en la investigació fa necessària una investigació en profunditat per a determinar la viabilitat i factibilitat de l'aplicació d'estos materials avançats en les BHE, facilitant en última instància la seua transformació en sistemes BTES fiables. Per tant, els principals objectius d'esta tesi doctoral són estudiar experimental i numèricament els impactes de l'ús de materials avançats per al fluid termòfor i el grouting com ara nanofluids i PCMs, en el rendiment del BHE com a sistemes BTES. L'estudi pretén seleccionar els materials més favorables, convertint-se en una referència pràctica i fiable per a futurs projectes i sectors industrials., [EN] Due to severe environmental pollution and worldwide energy deficiency, exploiting renewable energies has become more critical than ever. Shallow geothermal energy (SGE) is considered a sustainable and renewable energy source with significant advantages in space heating and cooling, industrial applications, greenhouses, electricity production, agriculture industry devices, and hot water production, among others. The ground source heat pump (GSHP) system is a promising technology for utilizing SGE. In this system, a borehole heat exchanger (BHE) plays an important role and directly influences the coefficient of performance (COP) of this shallow geothermal system. Different approaches have been carried out to enhance the performance of the BHE, including using advanced materials for pipes, heat transfer fluids, and backfill/grout, designing new geometries, and optimizing the BHE to be used as borehole thermal energy storage (BTES) systems. Drilling costs, heat pump electricity consumption, and borehole thermal resistance can be reduced using materials with appropriate thermo-physical properties like nanofluids and heat storage materials. This results in not only a more significant heat transfer between the heat transfer fluid, the backfill/grout, and the soil but also lessens the thermal effect on the surroundings. Heat transfer fluid is one of the factors in optimizing the BHE to be used for thermal energy storage (TES). Increased thermal conductivity in the heat transfer fluid enhances heat transfer efficiency between the fluid and the heat storage materials, leading to a more rapid attainment of the phase change temperature in the storage materials. In essence, when employing a heat transfer fluid with superior thermal conductivity, the temperature of the heat storage material experiences quicker fluctuations, resulting in a significant reduction in the duration required for a complete phase change. Moreover, the use of phase change material (PCM) as a heat storage medium instead of conventional backfill/grout enables the BHE to be beneficial and applicable as a BTES system. In addition to decreasing the required borehole depth considerably, the BTES system can store and release energy daily and seasonally to reduce the load during peak hours. However, there is a notable gap in the literature concerning exploring and applying new heat storage and heat transfer fluid materials in BHEs to render them suitable for TES purposes. While various approaches have been undertaken to enhance BHE performance, including using advanced materials and design optimizations, most research has concentrated on the conventional goal of BHEs. More attention should be given to the potential advantages of these heat exchangers by applying nanofluids and PCMs as heat transfer fluids and heat storage media, respectively. As mentioned above, these materials possess superior thermo-physical properties that can lead to more efficient heat transfer, reduced drilling costs, lower electricity consumption in heat pumps, and diminished borehole thermal resistance. This research gap necessitates an in-depth investigation to determine the feasibility and practicality of implementing these advanced materials in BHEs, ultimately facilitating their transformation into reliable BTES systems. The outcomes of such research endeavors hold the promise of addressing environmental concerns and global energy deficiencies by advancing the utilization of renewable energy sources like SGE sustainably and effectively. Therefore, the main objectives of this doctoral dissertation are to study experimentally and numerically the impacts of using advanced materials for heat transfer fluid and backfill/grout, such as nanofluids and PCMs, on the performance of the BHE as BTES systems. The study aims to select the most favorable materials, making it a practical and reliable reference for future projects and industry sectors., This research has received funding from the European Union’s Horizon 2020 Research and Innovation program named GEOCOND under grant agreement No [727583].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the Influence of Operational and Control Parameters in Thermal Response Testing of Borehole Heat Exchangers

  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Lemus Zúñiga, Lenin Guillermo|||0000-0002-6361-6019
  • Saiz Mauleón, María Begoña|||0000-0002-8650-0916
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
[EN] Thermal response test (TRT) is a common procedure for characterization of ground and borehole thermal properties needed for the design of a shallow geothermal heat pump system. In order to investigate and to develop more accurate and robust procedures for TRT control, modelling, and evaluation in semi-permeable soils with large water content, a pilot borehole heat exchanger was built in the main campus of the Universitat Politècnica de València. The present work shows the results of the experiments performed at the site, analysing the improvements that have been introduced both in the control of the heat injected during TRTs and in the methods to infer the ground thermal parameter. Three models are compared: two based on the infinite-line source theory and one based on the finite-line source scheme. The models were tested under two possible configurations of the equipment, i.e., with and without strict control of injected heat. Our results show the importance of heat injection control for a robust parameter assessment and the existence of additional heat transfer processes that the used models cannot completely characterize and that are related to the presence of significant groundwater flow at the site. In addition, our experience with the current installation and the knowledge about its strengths and weaknesses have allowed us to design a new and more complete test-site to help in the analysis and validation of new ground heat exchanger geometries., This work has received funding from the European Union’s Horizon 2020 Research and Innovation program under grant agreement Nos. (657982) and (727583).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Spatial analysis of indicators affecting the exploitation of shallow geothermal energy at European scale

  • Ramos-Escudero, Adela
  • Garcia-Cascales, M. Socorro
  • Cuevas Castell, José Manuel
  • Sanner, Burkhard
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
[EN] Shallow Geothermal Energy (SGE) exploited by vertical close loop Ground Source Heat Pumps (GSHP) is a proven, reliable, and widespread renewable heating and cooling technology. However, in many regions there is still a lack of awareness among policy makers and end users, constituting a major constraint to wider deployment of SGE. In order to contribute to its market consolidation, this work focuses on bringing to light relevant spatial information affecting the suitability of SGE exploitation. This information is the result of the systematization of geological, climatic, and environmental open and available data translated into performance indicators. A set of thematic maps was created using Geographic Information Systems (GIS) comprising the European Member States and other European countries. The relative area and the amount of population affected per indicator was spatially analyzed to determine the most common values found and the affected population. The relationship between area percentage and population affected percentage per indicator was also analyzed and allowed to identify the most common indicators values in areas where high energy demands are expected. Additionally, an example of how this data can be used into a Multi-Criteria Decision-Making (MCDM) framework is shown. (c) 2020 Elsevier Ltd. All rights reserved., This work was partially supported by the Spanish Ministry of Economy and Competitiveness (MINECO), reference TIN2017-86647-P. The authors also acknowledge the support of the Fundacion Seneca (Region of Murcia, Spain through the Grant 19882-GERM-15.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Adapted composite two-region line source methods for evaluation of borehole heat exchangers with advanced materials

  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Javadi, Hossein|||0000-0002-2059-7145
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Armengot-Carbó, B.|||0000-0001-7424-2975
[EN] The results of a large number of Thermal Response Tests (TRTs) performed on four different borehole heat exchangers (BHEs) were analyzed to explore the effect of the novel grouting and plastic pipe materials developed in a previous project on their thermal performance. For this purpose, two versions of the composite two-region line source approach have been adapted for its use for evaluating BHEs in practical situations, allowing us to obtain more comprehensive and consistent information on key thermal parameters of ground and fillers. We develop a scheme that combines the composite two-region model with unsteady TRT injection data to avoid some shortcomings that have appeared in previous implementations of this approach. Our new method enables us to obtain parameters otherwise difficult to obtain, such as the diffusivities, heat capacities, and conductivities of ground and grout. In comparison with standard line source based analysis, it allows to improve and enrich TRT execution, with a reduction in the test time required, lower uncertainties of the parameters obtained, and a deeper understanding of the thermal properties of the grout, ground, and borehole heat exchanger as all estimates are correlated to actual physical, mensurable soil and ground properties, which allows independent critical revision and check against alternative estimation methods.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Optimización teórico-experimental de sondas de calor para intercambio geotérmico (SGE) según condiciones hidrogeológicas, características geométricas y propiedades de sus materiales

  • Badenes Badenes, Borja|||0000-0002-3469-9265
[ES] Uno de los mayores retos para el mercado de bombas de calor geotérmicas es el alto coste asociado a la perforación de los intercambiadores de calor geotérmicos. Conseguir unos intercambiadores de calor geotérmicos más eficientes reduciría dicho coste, ya que sería necesaria una menor longitud de intercambiador para obtener las mismas temperaturas de trabajo en él (misma eficiencia de la bomba de calor). La eficiencia térmica de un intercambiador de calor geotérmico está caracterizada por su resistencia térmica. Dicha resistencia térmica depende de una serie de elementos entre los que se encuentran: propiedades y caudal del fluido que recorre el intercambiador de calor, diámetro de la perforación geotérmica, geometría y materiales de la tubería del intercambiador de calor y las propiedades del material de relleno de la perforación (grouting). Cuanto mayor sea la resistencia térmica del intercambiador de calor, menor será el calor transferido entre el fluido caloportador y el terreno, traduciéndose en una necesidad mayor de longitud de intercambiador enterrado. Por lo tanto, es necesario una reducción de este parámetro al mínimo posible. En consecuencia, el objetivo principal de esta tesis doctoral consiste en, a partir de un modelo analítico comprensivo de cuantificación del impacto de los parámetros anteriores, realizar un estudio detallado para analizar su influencia combinada en la resistencia térmica del intercambiador geotérmico, pero también examinando dicho efecto en otros planos, como costes económicos de ejecución del intercambiador y de explotación (consumo eléctrico de la bomba de calor y costes de bombeo asociados)., [CA] Un dels majors reptes per al mercat de bombes de calor geotèrmiques és l'alt cost associat a la perforació dels bescanviadors de calor geotèrmics. Aconseguir uns bescanviadors de calor geotèrmics més eficients reduiria aquest cost, ja que seria necessària una menor longitud de bescanviador per a obtenir les mateixes temperatures de treball en ell (mateixa eficiència de la bomba de calor). L'eficiència tèrmica d'un bescanviador de calor geotèrmic està caracteritzada per la seva resistència tèrmica. Aquesta resistència tèrmica depèn d'una sèrie d'elements entre els quals es troben: propietats i cabal del fluid que recorre el bescanviador de calor, diàmetre de la perforació geotèrmica, geometria i materials de la canonada del bescanviador de calor i les propietats del material de farciment de la perforació (grouting). Com més gran sigui la resistència tèrmica del bescanviador de calor, menor serà la calor transferida entre el fluid termòfor i el terreny, traduint-se en una necessitat major de longitud de bescanviador enterrat. Per tant, és necessari una reducció d'aquest paràmetre al mínim possible. En conseqüència, l'objectiu principal d'aquesta Tesi Doctoral consisteix en, a partir d'un model analític comprensiu de quantificació de l'impacte dels paràmetres anteriors, realitzar un estudi detallat per a analitzar la seva influència combinada en la resistència tèrmica del bescanviador geotèrmic, però també examinant aquest efecte en altres plans, com a costos econòmics d'execució del bescanviador i d'explotació (consum elèctric de la bomba de calor i costos de bombament)., [EN] One of the biggest challenges for the ground source heat pump market is the high cost associated with drilling geothermal borehole heat exchangers. Achieving more efficient geothermal heat exchangers would reduce this cost, since a shorter exchanger length would be required to obtain the same working temperatures in it (same efficiency of the heat pump). The thermal efficiency of a geothermal heat exchanger is characterized by its borehole thermal resistance. This borehole thermal resistance depends on a number of parameters, mainly: properties and flow rate of the working fluid that flows through the borehole heat exchanger, diameter of the geothermal borehole, geometry and materials of the heat exchanger pipe and the properties of the borehole grouting material. The higher thermal resistance of the heat exchanger, the less heat is transferred between the heat carrier fluid and the ground, resulting in an increased requirement for the length of the buried heat exchanger. Consequently, it is essential to reduce this parameter to the minimum possible. Therefore, the main objective of this Ph. Doctoral Thesis is to carry out, based on a comprehensive analytical model of quantification of the impact of the above mentioned parameters, a detailed study to analyze their combined influence on the thermal resistance of the geothermal borehole, but also exploring this effect in other less researched areas, such as economic costs of running the exchanger and operating it (electricity consumption of the heat pump and associated pumping costs)., This research has received funding from the European Union’s Horizon 2020 Research and Innovation program under grant agreement No [657982], [727583] and [792355].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical Study on the Thermal Performance of a Single U-Tube Borehole Heat Exchanger Using Nano-Enhanced Phase Change Materials

  • Javadi, Hossein|||0000-0002-2059-7145
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mousavi Ajarostaghi, Seyed Soheil
[EN] To investigate the impacts of using nano-enhanced phase change materials on the thermal performance of a borehole heat exchanger in the summer season, a three-dimensional numerical model of a borehole heat exchanger is created in the present work. Seven nanoparticles including Cu, CuO, Al2O3, TiO2, SiO2, multi-wall carbon nanotube, and graphene are added to the Paraffin. Considering the highest melting rate and lowest outlet temperature, the selected nano-enhanced phase change material is evaluated in terms of volume fraction (0.05, 0.10, 0.15, 0.20) and then the shape (sphere, brick, cylinder, platelet, blade) of its nanoparticles. Based on the results, the Paraffin containing Cu and SiO2 nanoparticles are found to be the best and worst ones in thermal performance improvement, respectively. Moreover, it is indicated that the increase in the volume fraction of Cu nanoparticles could enhance markedly the melting rate, being 0.20 the most favorable value which increased up to 55% the thermal conductivity of the nano-enhanced phase change material compared to the pure phase change material. Furthermore, the blade shape is by far the most appropriate shape of the Cu nanoparticles by considering about 85% melting of the nano-enhanced phase change materia, This research work has been supported financially by the European project GEOCOND (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No 727583) and by the European project GEO4CIVHIC (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No 792355).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of advanced materials guided by numerical simulations to improve performance and cost-efficiency of borehole heat exchangers (BHEs)

  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Lemus Zúñiga, Lenin Guillermo|||0000-0002-6361-6019
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Sanner, Burkhard
  • Cuevas, José Manuel
  • Bartoli, Flavia
  • Ciardelli, Francesco
  • González, Rosa M.
  • Ghafar, Ali Nejad
  • Fontana, Patrick
[EN] One promising way to improve the efficiency of borehole heat exchangers (BHEs) in shallow geothermal applications is to enhance the thermal properties of the materials involved in its construction. Early attempts, such as using metal tubes in the 1980s or the utilization of thin-foil hoses, did not succeed in being adopted by the market for diverse reasons (cost, corrosion, fragility, etc...). In parallel, the optimization of pipe size, the use of double-U-tubes, thermally enhanced grout, etc. were able to bring the measure for the BHE efficiency, the borehole thermal resistance, from 0.20 to 0.15 K/(Wm) down to 0.08-0.06 K/(Wm) in the best solutions today. A further improvement cannot be expected without development of new, dedicated materials, combining the versatility of plastic like PE with an increased thermal conductivity that matches the respective properties of the rock and soil. This goal was included in the Strategic Research and Innovation Agenda of the European Technology Platform on Renewable Heating and Cooling in 2013. Within an EU supported project, both BHE pipes and grouting materials have been produced prototypically in small amounts, suitable for the first tests in the intended environment. The present work explains the research pathways envisaged and the resulting sensitivity analysis to highlight the influence of some of the most critical parameters that affect the overall performance of a GSHP system. The results have allowed guiding the real development of more efficient new advanced materials for different scenarios representative of different European regions. Finally the developed materials and their properties are discussed, including a comparative assessment about their compliance with reference material properties as currently seen in the BHE market., This article is part of a project that has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 727583.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Laboratory and numerical study on innovative grouting materials applicable to borehole heat exchangers (BHE) and borehole thermal energy storage (BTES) systems

  • Javadi, Hossein|||0000-0002-2059-7145
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Lemus Zúñiga, Lenin Guillermo|||0000-0002-6361-6019
  • Ghafar, Ali Nejad
  • Arun Chaudhari, Ojas
  • Zirgulis, Giedrius
[EN] In this study, a laboratory-scale prototype of a borehole field has been designed and built to assess various innovative grouting products in a fully controlled environment. Three novel grout formulations are developed and evaluated: enhanced grout, a mixture of enhanced grout and microencapsulated phase change material, and a mixture of enhanced grout and shape stabilized phase change material. The objective is to evaluate the enhancement in their thermal properties (i.e., thermal conductivity and thermal energy storage capacity) compared to those using a commercial reference grout. Besides, threedimensional numerical modeling is performed to provide a better understanding of the heat transfer and phase transition inside and outside the grout columns and to study the capability of the developed grouts to be used in a borehole heat exchanger or as borehole thermal energy storage system. To the best of the authors' knowledge, there have been just a few numerical studies on using phase change materials inside borehole heat exchangers to assess thermal energy storage applications. The experimental and numerical results showed much higher efficiency of the grout developed with a high thermal conductivity than the reference grout in terms of heat transfer in both the grout column and the surrounding sand. Furthermore, the results indicated the noticeable influence of the microencapsulated phase change material's presence in the grout formulation in terms of heat absorption/storage during the phase transition (from solid to liquid). However, it is concluded that reengineering shape stabilized phase change material should be conducted to make it more appropriate for thermal energy storage applications, This article is part of a project that has received funding from the European Union's Horizon 2020 research and innovation pro-gramme under grant agreement No 727583.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Use of advanced pipe and grout materials in an experimental Single-U BHE: Installation procedure assessment and thermal properties comparison using C2RLSM

  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Armengot-Carbó, B.|||0000-0001-7424-2975
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Cuevas-Castell, José Manuel
  • Sanner, Burkhard
[EN] The performance of a Shallow Geothermal Energy System (SGES) is significantly influenced by the materials that conform its borehole heat exchangers (BHEs). Traditionally, plastic pipes and cement-based grouts, originally developed for other applications, have been employed in these systems due to their accessibility and ease of installation. However, these materials impose certain efficiency limitations. This article reports the installation process of two BHEs using new grout and pipe materials designed to increase their suitability for SGE systems. The validation process included material characterization tests during installation. Once installed, the new boreholes were compared with a reference BHE (based on standard pipes and grout) by performing standard Thermal Response Tests (TRT) on each borehole at the same thermal power injection rate. The Composite 2 Region Line Source Model (C2RLSM) has been used to analyse the TRT data. C2RLSM gives plausible estimates on the thermal properties of the ground and the BHE, including a comparable borehole thermal resistance R*b. We report improved R*b from 0.15 mK/W for standard materials to 0.1 mK/W for new materials. The use of these materials could imply CAPEX reductions of more than 20% in common BHE., This work has received funding from the European Union s Horizon 2020 Research and Innovation program under grants agreement No [792355] and No [727583].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

How Reliable Are Standard Thermal Response Tests? An Assessment Based on Long-TermThermal Response Tests Under Different Operational Conditions

  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Lemus Zúñiga, Lenin Guillermo|||0000-0002-6361-6019
  • Oliver Villanueva, José Vicente|||0000-0003-2842-7834
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Cuevas-Castell, José Manuel
[EN] In this contribution, we analyze the results of a number of thermal response test (TRT) experiments performed during several years at the same location at our university campus in Valencia (Spain), a permeable saturated soil area with possible groundwater flow conditions. A combination of different heat injection rates, TRT operation times of up to 32 days, and various methods for parameter estimation of ground thermal properties have been applied to study their influence on the result and accuracy of TRTs. Our main objective has been to experimentally quantify the influence of groundwater flow heat advection using moving infinite and finite line-source theories, as well as to analyze the influence of factors such as test duration, sensor accuracy, and external thermal influences. We have shown that the traditionally used infinite and finite line-source models, as well as the moving line-source models, can accurately represent experimental temperature evolution, but that there are many caveats regarding the significance parameters extracted and its reproducibility and stability. These features can be improved if data from the first test days are disregarded for the analysis, obtaining a much faster convergence to the definitive soil parameter estimates, including the effective Peclet number that represents groundwater flow in our particular case., This research was funded by the European Union's Horizon 2020 Research and Innovation program under grant agreement No [657982] and [727583].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Impact of Employing Hybrid Nanofluids as Heat Carrier Fluid on the Thermal Performance of a Borehole Heat Exchanger

  • Javadi, Hossein|||0000-0002-2059-7145
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Ajarostaghi, Seyed Soheil Mousavi
[EN] In this numerical study, 4 types of hybrid nanofluid, including Ag-MgO/water, TiO2-Cu/water, Al2O3-CuO/water, and Fe3O4-multi-wall carbon nanotube/water, have been considered potential working fluid in a single U-tube borehole heat exchanger. The selected hybrid nanofluid is then analyzed by changing the volume fraction and the Reynolds number. Based on the numerical results, Ag-MgO/water hybrid nanofluid is chosen as the most favorable heat carrier fluid, among others, considering its superior effectiveness, minor pressure drop, and appropriate thermal resistance compared to the pure water. Moreover, it was indicated that all cases of Ag-MgO/water hybrid nanofluid at various volume fractions (from 0.05 to 0.20) and Reynolds numbers (from 3200 to 6200) could achieve better effectiveness and lower thermal resistances, but higher pressure drops compared to the corresponding cases of pure water. Nevertheless, all the evaluated hybrid nanofluids present lower coefficient of performance (COP)-improvement than unity which means that applying them as working fluid is not economically viable because of having higher pressure drop than the heat transfer enhancement., This research work has been supported financially by the European project GEOCOND (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No 727583) and by the European project GEO4CIVHIC (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No 792355).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

New trilobular geometry using advanced materials for experimentally validated enhanced heat transfer in shallow geothermal applications

  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Armengot-Carbó, B.|||0000-0001-7424-2975
  • Javadi, Hossein|||0000-0002-2059-7145
[EN] The Adapted Conductivity Trilobular (ACT) design, comprising an up -flow central pipe and three satellite downward pipes, represents a novel configuration of a borehole heat exchanger. The novelty lies not only in the geometry of the heat exchanger, but also in the use of materials perfectly adapted to the thermal use for which they have been specified. The central pipe is constructed of a composite bilayer material with very low thermal conductivity, whereas the satellite pipes are based on a novel highly conductive plastic material. The primary objective behind this design was to simplify installation, by using essentially the same drilling and grouting methods used for conventional single -U or double -U borehole heat exchangers. In response to the rising demand for more efficient and affordable ground heat exchangers to be connected to Ground Source Heat Pump (GSHP) systems, this innovation was one of the promising outcomes of the GEOCOND European project. To assess ACT performance, the Geothermal Laboratory on the campus of the Universitat Politecnica de Valencia conducted a number of thermal response tests (TRTs), the experimental results of which are collected and analyzed in this paper. Additionally, a modified version of the Composite Two Region Line Source modeling scheme is described and used to assess the experimental data. A total of four demonstration boreholes - two single -U baseline and two ACT boreholes - have been tested. The experimental investigation using the C2RLS methodology reveals that the ACT configuration has a significantly lower thermal than the typical BHE arrangement and allows a greater specific heat injection rate. Specifically, a borehole resistance drop from 0.149 (m.K)/W to 0.07 (m.K)/W allowing higher injection rates to be achieved without an unsustainable increase in ground temperature. These findings may have significant implications for the development of more efficient and cost-effective GSHP systems., This work was developed within the European project GEOCOND and continued with the European project GEO4CIVHIC, funded by the European Union's Horizon 2020 research and innovation program, under grant agreement s No 727583 and No 792355, respectively.Acknowledgment to the support from the Program for the Re-qualification of the Spanish university system for 2021-2023 (in the framework of the call of the Universitat Politecnica de Valencia) , subsidized by the European Recovery Instrument (financed by the European Union by Next Generation EU) in the framework of the Spanish Recovery, Transformation and Resilience Plan, through the Ministry of Universities, regulated by RD 289/2021 and Order UNI/551/2021.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thermodynamic Performance Analysis of High Thermal Conductivity Materials in Borehole Heat Exchangers in the European Climate

  • Khattak, Sanober
  • Sanner, Burkhard
  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
[EN] While heat pumps have been acknowledged as a key enabling technology to achieve Net Zero goals, their uptake is limited by their performance and cost. In this paper, a simulation-based study is conducted to analyse the performance of ground source heat pumps (GSHPs) utilising high thermal conductivity materials for the borehole heat exchanger (BHE) pipe (1 W/mK) and grouting (3 W/mK) developed in the GEOCOND project. Exergy analysis is conducted to account for energy quantity and quality with a focus on BHE performance. An annual hourly simulation was performed using DesignBuilder V5.4 and Earth Energy Designer (EED4) for representative cool and hot locations in Europe-Stockholm and Valencia, respectively. For a constant BHE length, the results for Stockholm show that the high conductivity materials result in an increase of about 13% BHE exergy extraction compared to the standard grout and pipe, but no such improvement was observed for Valencia. The difference between outdoor temperature and its dynamic variation from the indoor setpoint is identified as a key factor in the overall GSHP exergetic performance. In future research, we propose a thorough life cycle analysis across diverse locations and varying indoor comfort criteria to pinpoint areas where the high thermal conductivity material can enable cost-effective, sustainable heating and cooling., This research work has been supported financially by the European project GEOCOND (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No. 727583) and by the European project GEO4CIVHIC (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No. 792355).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Theoretical and experimental cost-benefit assessment of borehole heat exchangers (BHEs) according to working fluid flow rate

  • Badenes Badenes, Borja|||0000-0002-3469-9265
  • Mateo Pla, Miguel Ángel|||0000-0002-8059-6996
  • Magraner, Teresa|||0000-0001-5292-1432
  • Soriano Olivares, Javier|||0000-0003-1649-102X
  • Urchueguía Schölzel, Javier Fermín|||0000-0002-3054-3431
[EN] In ground-source heat-pump systems, the heat exchange rate is influenced by various design and operational parameters that condition the thermal performance of the heat pump and the running costs during exploitation. One less-studied area is the relationship between the pumping costs in a given system and the heat exchange rate. This work analyzes the investment and operating costs of representative borehole heat-exchanger configurations with varying circulating flow rate by means of a combination of analytical formulas and case study simulations to allow a precise quantification of the capital and operational costs in typical scenario. As a conclusion, an optimal flow rate minimizing either of both costs can be determined. Furthermore, it is concluded that in terms of operating costs, there is an operational pumping rate above which performance of geothermal systems is energetically strongly penalized., This research work has been supported financially by the European project GEOCOND (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No 727583) and by the European project GEO4CIVHIC (funded by the European Union's Horizon 2020 research and innovation program under grant agreement No 792355).