Pasar al contenido principal

DISEÑO, GESTION Y CONTROL MEDIOAMBIENTAL DE REGADIOS MODERNIZADOS POR ASPERSION EN EL VALLE DEL EBRO

AGL2013-48728-C2-1-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Surface eddy fluxes and friction velocity estimates taking measurements at the canopy top

  • Castellví Sentís, Francesc
  • Medina, Eva T.
  • Cavero Campo, José
Agricultural engineers, crop physiologists and hydrologists are often forced to deploy instrumentation close to the canopy top to estimate surface eddy fluxes. This is a widely recognized problem either at farm-level or research-level. The eddy covariance (EC) method is grounded on hypothesis, simplifications and relationships valid in the inertial sublayer and alternative methods may require either calibration or inputs that are not commonly available. The present study enables a method that combines similarity, transilient and surface renewal theories in conjunction with the analysis of small eddies (Surface renewal of small eddies, SRSE, method) to estimate the friction velocity and surface fluxes of different scalars (sensible heat, latent heat and carbon dioxide) taking measurements at the canopy top. SRSE minimizes estimation of canopy parameters (only the zero-plane displacement is involved), allows implementing a primary flux quality control and to guide instrumentation deployment. For a mature maize crop, SRSE and EC surface energy balances indicated that EC was slightly more reliable than SRSE during daytime. For unstable cases, the normalized mean absolute error (MAE) to the available net surface energy (ANSE), MAE/ANSE, obtained by the EC and SRSE methods were 9% and 13 %, respectively. For stable cases during the day, 10 % and 11 %, respectively. For stable cases at night SRSE performed better than EC, MAE/ANSE were 23 % and 16 %, respectively. Regardless of the half-hourly eddy flux (including the friction velocity), the EC and SRSE were highly correlated (the minimum coefficient of determination was 0.91) and, in average (for all data) flux of scalars nearly matched including water-use-efficiency. To avoid acquisition of expensive and stringent instrumentation, the closure of the surface energy balance equation was forced to derive affordable approaches to estimate the latent heat flux for different stability cases., This work was supported under projects AGL2013-48728-C2-1-R and RTI2018-098693-B-C31 Ministerio de Economía y Competitividad of Spain.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación

Characterization and Simulation of a Low-Pressure Rotator Spray Plate Sprinkler Used in Center Pivot Irrigation Systems

  • Robles Rovelo, Octavio
  • Zapata Ruiz, Nery
  • Burguete Tolosa, Javier
  • Félix Félix, Jesús Ramiro
  • Latorre Garcés, Borja
Spray sprinklers enable to operate at low pressures (<103 kPa) in self-propelled irrigation machines. A number of experiments were performed to characterize the water distribution pattern of an isolated rotator spray plate sprinkler operating at very low pressure under different experimental conditions. The experiments were performed under two pressures (69 kPa and 103 kPa) and in calm and windy conditions. The energy losses due to the impact of the out-going jet with the sprinkler plate were measured using an optical technique. The adequacy to reproduce the measured water distribution pattern under calm conditions of two drop size distribution models was evaluated. A ballistic model was used to simulate the water distribution pattern under wind conditions evaluating three different drag models: (1) considering solid spherical drops; (2) a conventional model based on wind velocity and direction distortion pattern, and (3) a new drag coefficient model independent of wind speed. The energy losses measured with the optical method range from 20% to 60% from higher to lower nozzle sizes, respectively, for both evaluated working pressures analyzing over 16,500 droplets. For the drop size distribution selected, Weibull accurately reproduced the water application with a maximum root mean square error (RMSE) of 19%. Up to 28% of the RMSE could be decreased using the wind-independent drag coefficient model with respect to the conventional model; the difference with respect to the spherical model was 4%., This research was funded by MICINN of the Government of Spain through the grants AGL2013-48728-C2-1-R and AGL2017-89407-R. Octavio Robles received a scholarship granted by the Minister of Economy and Competitiveness of the Spanish Government.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Self-calibrated ballistic model for sprinkler irrigation with a field experiments data base

  • Robles Rovelo, Octavio
  • Latorre Garcés, Borja
  • Zapata Ruiz, Nery
  • Burguete Tolosa, Javier
56 Pags.- 5 Tabls.- 8 Figs. The definitive version is available at: https://www.sciencedirect.com/science/journal/03783774, Simulation models of sprinkler irrigation are a valuable tool to improve the irrigation water management at plot scale. Ballistic theory has been commonly used to simulate drop dynamics in sprinkler irrigation models. A number of experiments on sprinkler irrigation performed in previous studies in the Ebro Valley Spain were analyzed and integrated in a data base. The evaluations were performed on six sprinkler types with different nozzle sizes, operating pressures under different meteorological conditions and spacings. The data base includes 40 isolated and 167 solid-set experiments that were processed with a self-calibrated model to calibrate and validate the ballistic parameters. The ballistic model used in this research was improved with respect to a previous model, moreover some novelties were added. These modifications were done in the phases of: the numerical solution, a wind drift and evaporation losses model, simulations considering slope in the terrain, drop generation (using regular and random methods), the size of the terrain cells where the drops are simulated and considering two drop size distributions, upper limit lognormal and Weibull. The results indicated larger and significant differences of Christiansen´s Uniformity Coefficient measured and simulated when considering a constant wind velocity (9%) and no differences when the wind velocity is defined for intervals equal to or less than 30 min (6%). Regarding the effect of the slope in the terrain, differences between both uniformity coefficients are relevant (11%) when the wind velocity is larger than 4 m s−1. Both drop size distributions were similar in accuracy however, the upper limit lognormal was more suitable to simulate a sprinkler especially designed to operate under low pressure. The predictive ability of the model once calibrated and validated was satisfactory (99% and 75%, respectively). The new model improves the accuracy with respect to previous research and minimizes the computing time for the calibration and validation processes using the cluster Trueno-CSIC., This research was funded by MICINN of the Government of Spain through grant AGL2013-48728-C2-1-R and AGL2017-89407-R. Octavio Robles received a scholarship granted by the Minister of Economy and Competitiveness of the Spanish Government., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Surface eddy fluxes and friction velocity estimates taking measurements at the canopy top

  • Castellví, F.
  • Medina Pueyo, Eva Teresa
  • Cavero Campo, José
50 Pags.- 2 Tabls.- 10 Figs. The definitive version is available at: https://www.sciencedirect.com/science/journal/03783774, Agricultural engineers, crop physiologists and hydrologists are often forced to deploy instrumentation close to the canopy top to estimate surface eddy fluxes. This is a widely recognized problem either at farm-level or research-level. The eddy covariance (EC) method is grounded on hypothesis, simplifications and relationships valid in the inertial sublayer and alternative methods may require either calibration or inputs that are not commonly available. The present study enables a method that combines similarity, transilient and surface renewal theories in conjunction with the analysis of small eddies (Surface renewal of small eddies, SRSE, method) to estimate the friction velocity and surface fluxes of different scalars (sensible heat, latent heat and carbon dioxide) taking measurements at the canopy top. SRSE minimizes estimation of canopy parameters (only the zero-plane displacement is involved), allows implementing a primary flux quality control and to guide instrumentation deployment. For a mature maize crop, SRSE and EC surface energy balances indicated that EC was slightly more reliable than SRSE during daytime. For unstable cases, the normalized mean absolute error (MAE) to the available net surface energy (ANSE), MAE/ANSE, obtained by the EC and SRSE methods were 9% and 13 %, respectively. For stable cases during the day, 10 % and 11 %, respectively. For stable cases at night SRSE performed better than EC, MAE/ANSE were 23 % and 16 %, respectively. Regardless of the half-hourly eddy flux (including the friction velocity), the EC and SRSE were highly correlated (the minimum coefficient of determination was 0.91) and, in average (for all data) flux of scalars nearly matched including water-use-efficiency. To avoid acquisition of expensive and stringent instrumentation, the closure of the surface energy balance equation was forced to derive affordable approaches to estimate the latent heat flux for different stability cases., This work was supported under projects AGL2013-48728-C2-1-R and RTI2018-098693-B-C31 Ministerio de Economía y Competitividad of Spain., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mycotoxins and crop yield in maize as affected by irrigation management and tillage practices

  • Herrera, Marta
  • Cavero Campo, José
  • Franco-Luesma, Samuel
  • Álvaro-Fuentes, Jorge
  • Ariño, Agustín
  • Lorán, Susana
11 Pags.- 4 Tabls. Data Availability Statement: The data presented in this study are available in the article. © 2023 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license., In addition to the weather conditions, agronomic practices can have a major influence on maize crop yield and contamination with mycotoxins. In this work, the effect of different irrigation systems (flood vs. sprinkler irrigation), sprinkler irrigation management (low vs. high frequency, daytime vs. nighttime irrigation) and tillage practices (conventional tillage, no tillage with or without crop stover) on crop yield and the contamination with aflatoxins (AFs), fumonisins (FUM) and deoxynivalenol (DON) were evaluated in the maize grain from two experimental maize fields. No aflatoxins were detected in any of the samples analyzed. DON and FUM levels were significantly higher when the sprinkler irrigation was performed at nighttime (0.54 and 1.21 mg kg−1, respectively) as compared to daytime (0.38 and 0.45 mg kg−1). Likewise, DON and FUM were greater when irrigation frequency was low (0.61 and 1.09 mg kg−1, respectively) in comparison with high frequency (0.30 and 0.57 mg kg−1). DON concentrations were significantly higher in fields with sprinkler irrigation (0.53 mg kg−1) as compared to flood irrigation (0.19 mg kg−1), while the levels of FUM were very similar regardless of the maize irrigation system. Mycotoxin concentrations were not affected by the different soil tillage practices. This highlights the importance of implementing crop management practices to minimize the risk of mycotoxin contamination in maize., This research was funded by the Spanish Agencia Estatal de Investigación (grant numbers PID2019-106877RA-I00, AGL2013-48728-C2-1-R, AGL2013-49062-C4-4-R) and the Government of Aragón (grant Grupo AESA)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Characterization and simulation of a low-pressure rotator spray plate sprinkler used in center pivot irrigation systems

  • Robles Rovelo, Cruz Octavio
  • Zapata Ruiz, Nery
  • Burguete Tolosa, Javier
  • Félix-Félix, Jesús Ramiro
  • Latorre, Borja
Spray sprinklers enable to operate at low pressures (<103 kPa) in self-propelled irrigation machines. A number of experiments were performed to characterize the water distribution pattern of an isolated rotator spray plate sprinkler operating at very low pressure under dierent experimental conditions. The experiments were performed under two pressures (69 kPa and 103 kPa) and in calm and windy conditions. The energy losses due to the impact of the out-going jet with the sprinkler plate were measured using an optical technique. The adequacy to reproduce the measured water distribution pattern under calm conditions of two drop size distribution models was evaluated. A ballistic model was used to simulate the water distribution pattern under wind conditions evaluating three different drag models: (1) considering solid spherical drops; (2) a conventional model based on wind velocity and direction distortion pattern, and (3) a new drag coeffcient model independent of wind speed. The energy losses measured with the optical method range from 20% to 60% from higher to lower nozzle sizes, respectively, for both evaluated working pressures analyzing over 16,500 droplets. For the drop size distribution selected, Weibull accurately reproduced the water application with a maximum root mean square error (RMSE) of 19%. Up to 28% of the RMSE could be decreased using the wind-independent drag coeffcient model with respect to the conventional model; the dierence with respect to the spherical model was 4%.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Mycotoxins and crop yield in maize as affected by irrigation management and tillage practices

  • Herrera, Marta
  • Cavero, José
  • Franco-Luesma, Samuel
  • Álvaro-Fuentes, Jorge
  • Ariño, Agustín
  • Lorán, Susana
In addition to the weather conditions, agronomic practices can have a major influence on maize crop yield and contamination with mycotoxins. In this work, the effect of different irrigation systems (flood vs. sprinkler irrigation), sprinkler irrigation management (low vs. high frequency, daytime vs. nighttime irrigation) and tillage practices (conventional tillage, no tillage with or without crop stover) on crop yield and the contamination with aflatoxins (AFs), fumonisins (FUM) and deoxynivalenol (DON) were evaluated in the maize grain from two experimental maize fields. No aflatoxins were detected in any of the samples analyzed. DON and FUM levels were significantly higher when the sprinkler irrigation was performed at nighttime (0.54 and 1.21 mg kg−1, respectively) as compared to daytime (0.38 and 0.45 mg kg−1). Likewise, DON and FUM were greater when irrigation frequency was low (0.61 and 1.09 mg kg−1, respectively) in comparison with high frequency (0.30 and 0.57 mg kg−1). DON concentrations were significantly higher in fields with sprinkler irrigation (0.53 mg kg−1) as compared to flood irrigation (0.19 mg kg−1), while the levels of FUM were very similar regardless of the maize irrigation system. Mycotoxin concentrations were not affected by the different soil tillage practices. This highlights the importance of implementing crop management practices to minimize the risk of mycotoxin contamination in maize.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Low-pressure sprinkler irrigation in maize: differences in water distribution above and below the crop canopy

  • Zapata, N.
  • Robles, O.
  • Playán, E.
  • Paniagua, P
  • Romano, C.
  • Salvador, R.
  • Montoya, F.
Reducing the working pressure at the sprinkler nozzles is one of the alternatives to reduce energy requirements in solid-set sprinkler irrigation systems. Previous studies reported ≈10% lower seasonal Christiansen uniformity coefficient (CUC) for low-pressure treatments than for standard treatments, but no differences in maize yield. This research analyses the effect of maize canopy water partitioning on irrigation performance indexes (CUC and wind drift and evaporation losses, WDEL). Three irrigation treatments were considered, based on the working pressure: 1) A standard brass impact sprinkler operating at a pressure of 300 kPa (CIS300); 2) A standard brass impact sprinkler operating at a pressure of 200 kPa (CIS200); and 3) A modified plastic impact sprinkler (with a deflecting plate attached to the drive arm) operating at a pressure of 200 kPa (DPIS200). Irrigation performance was measured using a catch-can network located above the maize canopy (CUCac, WDELac) along the whole crop season and using stemflow and throughfall devices below the maize canopy (CUCbc, WDELbc) in eight irrigation events. Maize growth, yield and its components were measured. Under low-wind and fully developed canopy conditions (a frequent situation for maize irrigation), CUCbc resulted higher than CUCac for the low-pressure treatments, while the opposite was observed for the standard pressure treatment. Maize canopy partitioning reduces the differences in irrigation performance indexes between pressure treatments, explaining why there are no differences in grain yield between them. Caution should be used when measuring sprinkler irrigation performance above tall canopies, since the elevation of the catch-cans and the crop canopy partitioning affect performance estimations.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Surface eddy fluxes and friction velocity estimates taking measurements at the canopy top

  • Castellví Sentís, Francesc
  • Medina, Eva T.
  • Cavero Campo, José
Agricultural engineers, crop physiologists and hydrologists are often forced to deploy instrumentation close to the canopy top to estimate surface eddy fluxes. This is a widely recognized problem either at farm-level or research-level. The eddy covariance (EC) method is grounded on hypothesis, simplifications and relationships valid in the inertial sublayer and alternative methods may require either calibration or inputs that are not commonly available. The present study enables a method that combines similarity, transilient and surface renewal theories in conjunction with the analysis of small eddies (Surface renewal of small eddies, SRSE, method) to estimate the friction velocity and surface fluxes of different scalars (sensible heat, latent heat and carbon dioxide) taking measurements at the canopy top. SRSE minimizes estimation of canopy parameters (only the zero-plane displacement is involved), allows implementing a primary flux quality control and to guide instrumentation deployment. For a mature maize crop, SRSE and EC surface energy balances indicated that EC was slightly more reliable than SRSE during daytime. For unstable cases, the normalized mean absolute error (MAE) to the available net surface energy (ANSE), MAE/ANSE, obtained by the EC and SRSE methods were 9% and 13 %, respectively. For stable cases during the day, 10 % and 11 %, respectively. For stable cases at night SRSE performed better than EC, MAE/ANSE were 23 % and 16 %, respectively. Regardless of the half-hourly eddy flux (including the friction velocity), the EC and SRSE were highly correlated (the minimum coefficient of determination was 0.91) and, in average (for all data) flux of scalars nearly matched including water-use-efficiency. To avoid acquisition of expensive and stringent instrumentation, the closure of the surface energy balance equation was forced to derive affordable approaches to estimate the latent heat flux for different stability cases., This work was supported under projects AGL2013-48728-C2-1-R and RTI2018-098693-B-C31 Ministerio de Economía y Competitividad of Spain.