Pasar al contenido principal

PROCESADO Y CARACTERIZACION MICROESTRUCTURAL, MECANICA Y ELECTRICA DE COMPUESTOS CERAMICA-GRAFENO

BES-2016-078711

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Contratos Predoctorales
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE SEVILLA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrical performance of orthotropic and isotropic 3YTZP composites with graphene fillers

  • López-Pernía, Cristina
  • Muñoz, Ferreiro, Carmen
  • Moriche, R.
  • Morales-Rodríguez, Ana
  • Gallardo-López, Ángela
  • Poyato, Rosalía
3 mol% yttria tetragonal zirconia polycrystal (3YTZP) composites with orthotropic or isotropic microstructures were obtained incorporating few layer graphene (FLG) or exfoliated graphene nanoplatelets (e-GNP) as fillers. Electrical conductivity was studied in a wide range of contents in two configurations: perpendicular (σꓕ) and parallel (σ//) to the pressing axis during spark plasma sintering (SPS). Isotropic e-GNP composites presented excellent electrical conductivity for high e-GNP contents (σꓕ ∼ 3200 S/m and σ// ∼ 1900 S/m for 20 vol% e-GNP), consequence of their misoriented distribution throughout the matrix. Optimum electrical performance was achieved in the highly anisotropic FLG composites, with high electrical conductivity for low contents (σꓕ ∼ 680 S/m for 5 vol%), percolation threshold below 2.5 vol% FLG and outstanding electrical conductivity for high contents (σꓕ ∼ 4000 S/m for 20 vol%), result of the high aspect ratio and low thickness of FLG., This research was supported by project PGC2018–101377-B-100 funded by MCIN/AEI/ 10.13039/501100011033 (Ministerio de Ciencia e Innovación, Spanish Government, Agencia Estatal de Investigación) and ERDF (European Regional Development Funding) “A way of making Europe”, by the European Union and by project P20_01024 (Junta de Andalucía/FEDER, UE 2014–2020). C. López-Pernía acknowledges the financial support of MINECO (Ministerio de Economía y Competitividad, Spanish Government) through the FPI contract ref: BES-2016- 078711. C. Muñoz-Ferreiro acknowledges the financial support of a VI PPIT-US (Plan Propio Universidad de Sevilla, Spain) fellowship through the contract USE-18740-H., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unravelling the optimization of few-layer graphene crystallinity and electrical conductivity in ceramic composites by Raman spectroscopy

  • Muñoz, Ferreiro, Carmen
  • López-Pernía, Cristina
  • Gallardo-López, Ángela
  • Poyato, Rosalía
Zirconia composites with few-layer graphene (FLG) were prepared by two powder processing routines -ultrasonic agitation or planetary ball milling- and spark plasma sintered at 1250 and 1300 °C. An in-depth study of the crystallinity of FLG, in terms of presence and nature of defects, was performed by Raman spectroscopy, revealing enhanced FLG crystallinity after sintering. This enhancement was more noticeable in the composites sintered at the highest temperature, with lower amount of structural defects and amorphous carbon. However, remaining amorphous carbon was detected in the composites prepared by planetary ball milling even after sintering at the highest temperature, resulting in lower electrical conductivities. Optimum results in terms of electrical conductivity were achieved for the composites prepared by ultrasonic agitation and sintered at 1300 °C, with electrical percolation limit below 2.5 vol% FLG and high electrical conductivity (678 S/m for 5 vol% FLG), as result of the enhanced FLG crystallinity after sintering., This research was supported by the Ministerio de Ciencia, Innovación y Universidades (MCIU) under the project PGC 2018-101377-B-100 (MCIU/AEI/FEDER, UE). C. López-Pernía acknowledges the financial support of MINECO through the FPI contract ref: BES-2016-078711. C. Muñoz-Ferreiro acknowledges the financial support of a VI PPIT-US fellowship through the contract USE-18740-H., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly efficient electrical discharge machining of yttria-stabilized zirconia ceramics with graphene nanostructures as fillers

  • Muñoz, Ferreiro, Carmen
  • López-Pernía, Cristina
  • Moriche, R.
  • Gommeringer, A.
  • Kern, F.
  • Poyato, Rosalía
  • Gallardo-López, Ángela
Electrical-discharge machining (EDM) of advanced ceramics allows the miniaturization of parts with complex shapes. Since electrical conductivity is required, non-conductive ceramics need a conductive second phase. This work assesses the feasibility of industrial EDM in advanced yttria-stabilized tetragonal zirconia (3YTZP) composites with 20 vol% graphene nanostructures with different morphology using different EDM energies. The structural integrity of the graphene nanostructures, the roughness of the machined surfaces and the geometrical tolerances have been evaluated by Raman spectroscopy, confocal microscopy and scanning electron microscopy, showing that it is possible to obtain a stable and efficient EDM process in these composites using low electrode energies. The use of the largest and thickest graphene nanostructures led to the best performance in terms of EDM machinability, the smallest nanostructures produced the best surface finish for low electrode energy and the thinnest nanostructures allowed the highest material removal rate at medium energy in the composites., This research was supported by the projects PGC2018-101377-B-100 funded by MCIN/AEI/ 10.13039/501100011033 (Ministerio de Ciencia e Innovación, Spanish Government, Agencia Estatal de Investigación) and ERDF (European Regional Development Funding) “A way of making Europe”, by the European Union and project P20_01024 (Junta de Andalucía/FEDER, UE 2014–2020). C. López-Pernía acknowledges the financial support of MINECO (Ministerio de Economía y Competitividad, Spanish Governmet) through the FPI contract ref: BES-2016- 078711. C. Muñoz-Ferreiro acknowledges the financial support of a VI PPIT-US (Plan Propio Universidad de Sevilla, Spain) fellowship through the contract USE-18740-H. R. Moriche acknowledges the financial support of MINECO through the Juan de la Cierva Postdoctoctoral Program (FJCI-2017-32502)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ageing-resistant zirconia/graphene-based nanostructures composites for use as biomaterials

  • Morales-Rodríguez, Ana
  • González-Orellana, C.
  • Pérez-García, Antonio A.
  • López-Pernía, Cristina
  • Muñoz, Ferreiro, Carmen
  • Poyato, Rosalía
  • Gallardo-López, Ángela
This work explores the incorporation of graphene-based two-dimensional nanostructures as moisture barriers to delay hydrothermal ageing of yttria-stabilized zirconia and strengthen its use in biomedical applications. Two sets of highly dense zirconia composites incorporating multilayered graphene with very different lateral dimensions, few layer graphene and exfoliated graphene nanoplatelets, were prepared. The effect of the addition of graphene nanostructures on zirconia ageing was investigated by conducting accelerated hydrothermal degradation experiments in an autoclave. An improved resistance to low-temperature degradation and a high tolerance to damage were achieved in the composites compared to those of monolithic zirconia. The incorporation of 1 vol% multilayered graphene was very effective in restricting the hydrothermal degradation. In particular, the composite incorporating exfoliated graphene nanosheets exhibited outstanding resistance to ageing because of their fine dispersion throughout the matrix, which effectively seemed to restrict grain growth and slow the propagation of the transformation front to the ceramic bulk., This research was supported by the Ministerio de Ciencia, Innovación y Universidades (MCIU) under the project PGC 2018-101377-B-100 (MCIU/AEI/FEDER, UE) and by the Universidad de Sevilla (US) under the contract 2018/00000663 VI PPIT-US USO SSGG. C. López-Pernía acknowledges the financial support of MINECO through the FPI contract ref: BES-2016-078711. C. Muñoz-Ferreiro acknowledges the financial support of a VI PPIT-US fellowship through the contract USE-18740-H., Peer reviewed