Pasar al contenido principal

TECNICAS NO CONVENCIONALES PARA LA LIMPIEZA DE MEMBRANAS DE ULTRAFILTRACION APLICADAS EN LA INDUSTRIA ALIMENTARIA

CTM2010-20186

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2010
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fouling mechanisms of ultrafiltration membranes fouled with whey model solutions

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
In this work, three ultrafiltration (UF) membranes with different molecular weight cut-offs (MWCOs) and made of different materials were fouled with several whey model solutions that consisted of bovine serum albumin (BSA) (1% w/w), BSA (1% w/w) and CaCl2 (0.06% w/w in calcium) and whey protein concentrate (WPC) with a total protein content of 45% w/w at three different concentrations (22.2, 33.3 and 44.4 g·L− 1). The influence of MWCO and membrane material on the fouling mechanism dominating the UF process was investigated. Experiments were performed using two flat-sheet organic membranes and a ceramic monotubular membrane whose MWCOs were 5, 30 and 15 kDa, respectively. Hermia's models adapted to crossflow UF, a combined model based on complete blocking and cake formation equations and a resistance-in-series model were fitted to permeate flux decline curves. The results demonstrated that permeate flux decline was accurately predicted by all the models studied. However, the models that fitted the best to permeate flux decline experimental data were the combined model and the resistance-in-series model. Therefore, complete blocking and cake formation were the predominant mechanisms for all the membranes and feed solutions tested., The authors of this work wish to gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation through the project CTM2010-20186.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of the hydraulic cleaning efficiency as a function of the operating conditions in the ultrafiltration of BSA solutions

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
This work was supported by the Spanish Ministry of Science and Innovation through the project CTM2010-20186 and by the Polytechnic University of Valencia under its program PAID.06-10
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Utilization of NaCl solutions to clean ultrafiltration membranes fouled by whey protein concentrates

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
  • Lora-García, Jaime|||0000-0003-1699-5404
In this work, whey protein concentrate (WPC) solutions at different concentrations (22.2, 333 and 150 g L-1) were used to foul three ultrafiltration (UF) membranes of different materials and molecular weight cut-offs (MWCOs): a polyethersulfone (PES) membrane of 5 kDa, a ceramic ZrO2-TiO2 membrane of 15 kDa and a permanently hydrophilic polyethersulfone (PESH) membrane of 30 kDa. NaCl solutions at different salt concentrations, temperatures and crossflow velocities were used to clean the UF membranes tested. The cleaning efficiency was related to the MWCO, membrane material and operating conditions during fouling and cleaning steps. NaCl solutions were able to completely clean the membranes fouled with the WPC solutions at the lowest concentration tested. As WPC concentration increased, the hydraulic cleaning efficiency (HCE) decreased. The results demonstrated that an increase in temperature and crossflow velocity of the cleaning solution caused an increase in the HCE. Regarding NaCl concentration, the HCE increased up to an optimal value. As the concentration was greater than this value, the cleaning efficiency decreased. In addition, an equation that correlates the cleaning efficiency to the operating parameters studied in this work (temperature, NaCl concentration, crossflow velocity in the cleaning procedure and WPC concentration during the fouling step) was developed and then, an optimization analysis was performed to determine the values of the parameters that lead to a 100% cleaning efficiency., The authors of this work wish to gratefully acknowledge the financial support from the Spanish Ministry of Science and Innovation through the project CTM2010-20186.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic Cleaning Of Ultrafiltration Membranes Fouled With BSA Solution

  • Lujan Facundo, Maria Jose|||0000-0001-6871-0584
  • Mendoza Roca, José Antonio
  • Cuartas Uribe, Beatriz Elena|||0000-0003-2835-900X
  • Alvarez Blanco, Silvia
The objective of this work was to investigate the effect of ultrasounds (US) on the flux recovery of ultrafiltration (UF) membranes fouled with bovine serum albumin (BSA) solution. Chemical cleaning was carried out with NaOH solution. The effect of ultrasonic frequency in the cleaning step was evaluated. Tests were performed in a laboratory plant equipped with a flat sheet module for two membranes. The membranes used were UH030 and UP005. Results showed that the lowest US frequency was the most effective one, producing an enhancement of 9 12% in the flux recovery of the membranes. On the other hand, neither pH nor temperature proved to be significant factors on the flux recovery. The use of US technique is an effective and promising approach to clean UF membranes after being fouled with BSA solution and may have a relevant influence on the overall process efficiency, This work was supported by the Spanish Ministry of Science and Innovation (CTM 2010-20.186).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Membrane fouling in whey processing and subsequent cleaning with ultrasounds for a more sustainable process

  • Lujan Facundo, Maria Jose|||0000-0001-6871-0584
  • Mendoza Roca, José Antonio
  • Cuartas Uribe, Beatriz Elena|||0000-0003-2835-900X
  • Alvarez Blanco, Silvia
[EN] Cost reduction and minimization of environmental impacts, based on by-product recovery, is the objective of applying the ultrafiltration technology for the treatment of cheese whey. In this work, ultrafiltration process was studied in an integrated way (filtration and membrane cleaning), focusing especially on the membrane cleaning. Membrane cleaning experiments were carried out with and without ultrasounds to evaluate the effect of ultrasounds on the membrane cleaning efficiency and, as a result, to reduce the consumption of chemicals. Tests were performed with two ultrafiltration polymeric membranes with molecular weight cut-offs of 30,000 Da (UH030) and 5000 Da (UP005). Fouling experiments were carried out with Renylat whey protein concentrate solutions and CaCl2 addition at a transmembrane pressure of 2 bar and cross flow velocity of 2 m/s during 2 h. Results showed that the presence of calcium increased the membrane fouling of both membranes. For UH030 membrane the reversible fouling prevailed over the irreversible fouling, meanwhile for UP005 membrane the irreversible fouling was the predominant one. Cleaning efficiency results demonstrated that ultrasounds application is an effective technique to clean ultrafiltration membranes after being fouled with whey protein concentrate solutions and may have a paramount importance on the overall process efficiency., This work was supported by the Spanish Ministry of Science and Innovation (CTM 2010-20.186).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrafiltration of whey: membrane performance and modelling using a combined pore blocking-cake formation model

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
[EN] BACKGROUNDUltrafiltration has been considered as a green' technique to treat different industrial wastewaters, such as whey in the dairy industry. However, fouling is one of the major drawbacks in the industrial implementation of this process. Thus, in this work, the performance of ultrafiltration membranes was investigated in terms of permeate flux and protein rejection when treating different whey model solutions. Modelling of permeate flux was performed combining two main fouling mechanisms (complete pore blocking and cake formation) by a time-dependent pore blocking parameter. RESULTSResults demonstrated that high protein concentration and the presence of calcium salts in the feed solution favoured permeate flux decline. The combined model was appropriate to describe the main fouling mechanisms, with fitting accuracies higher than 0.960. Model parameters were correlated with both calcium and protein concentration and the developed model was successfully validated with an additional fouling test. CONCLUSIONAll the membranes tested were suitable for carrying out whey protein separation, with rejection indexes greater than 99%. The combined model and the statistical correlation of model parameters with calcium and protein concentrations were useful to predict permeate flux decline when the ultrafiltration of a new whey model solution was performed. (c) 2017 Society of Chemical Industry, This work was supported by the Spanish Ministry of Science and Innovation (project CTM2010-20186).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of membrane cleaning with and without ultrasounds application after fouling with three model dairy solutions

  • Lujan Facundo, Maria Jose|||0000-0001-6871-0584
  • Mendoza Roca, José Antonio
  • Cuartas Uribe, Beatriz Elena|||0000-0003-2835-900X
  • Alvarez Blanco, Silvia
The aim of this study was to investigate the behavior of two ultrafiltration (UF) membranes after their fouling with different fouling solutions and cleaning with a surfactant, including the application of ultrasounds (US). Thus,two UF membranes (UH030 and UP005) were fouled with three different whey model solutions that consisted of bovine serum albumin (BSA) with a concentration of 1% (w/w), BSA (1%, w/w) plus CaCl2 with a concentration of 0.17% (w/w) and whey solution (Renylat 45) with a concentration of 2.22% (w/w). Chemical cleaning was carried out with P3 Ultrasil 115 solution at temperatures between 25 ◦C and 45 ◦C and concentrations in the range between 0.5% (v/v) and 0.9% (v/v). US were applied in some ofthe tests at a frequency of 20 kHz and nominal power of 300W. The results demonstrated that US cleaning was effective to enhance the permeability recovery, although this enhancement was only up to 9%. Concerning fouling, results from resistances calculations showed that for UH030 membrane prevails the reversible fouling whereas for UP005 membrane predominate irreversible fouling, This work was supported by the Spanish Ministry of Science and Innovation (CTM 2010-20.186).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of cleaning efficiency of ultrafiltration membranes fouled by BSA using FTIR–ATR as a tool

  • Lujan Facundo, Maria Jose|||0000-0001-6871-0584
  • Mendoza Roca, José Antonio
  • Cuartas Uribe, Beatriz Elena|||0000-0003-2835-900X
  • Alvarez Blanco, Silvia
The goal of this paper was to study the cleaning of two polyethersulfone (PES) membranes of different molecular weight and fouled with BSA solution. Ultrafiltration (UF) membranes were tested in a flat sheet module. Fouling experiments were carried out at a transmembrane pressure of 2 bar and cross flow velocity of 2 m/s during 2 h. Cleaning experiments were performed at 1 bar and 2.2 m/s. To compare the efficiency of different cleaning solutions (NaOH and P3-Ultrasil 115), quantification of residual pro-teins on the membrane was carried out by FTIR ATR. To have a better understanding of the cleaning pro-cess, characteristics of the feed solution and of the membranes were considered and contact angle of the membranes before and after the cleaning was measured. Membrane resistances were also calculated at the different stages. Results from resistances showed that reversible fouling prevail over irreversible fouling for both membranes. P3-Ultrasil 115 was a better cleaning agent than NaOH solution since cleaning efficiencies (CE) of 100% for both membranes were achieved for P3-Ultrasil 115 solution. Residual pro-teins on the membrane after the cleaning were measured both by FTIR ATR and Pierce-BCA method. Results showed that 100% of permeability recovery did not imply the complete BSA removal from the membrane. However, these measurements corroborated that P3-Ultrasil 115 had removed a higher amount of proteins than NaOH solution., This work was supported by the Spanish Ministry of Science and Innovation (CTM 2010-20.186).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of fouling resistances during the ultrafiltration of whey model solutions

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
[EN] In the last decades, the ultrafiltration of whey has grown in importance as a "green" technique. However, since fouling is an important drawback, researchers focused on its prediction by mathematical models. In this work, three ultrafiltration membranes of different molecular weight cut-offs and materials were used to ultrafilter whey model solutions of different protein concentrations. As a novelty, a resistance-in-series model that accounts for the time evolution of the fouling resistances was considered. The results demonstrated that the higher the protein and salt concentrations in the feed solutions were, the greater the fouling degree was. The resistance-in-series model was accurately fitted to the experimental data for each membrane and feed solution used. The results showed that the resistance due to adsorption dominated the first minutes of operation, while the membrane characteristics (surface roughness and hydrophilicity/hydrophobicity) played an important role in the growth of the cake layer. (C) 2017 Elsevier Ltd. All rights reserved., The authors of this work wish to gratefully acknowledge the financial support provided by the Spanish Ministry of Science and Innovation through its project CTM2010-20186.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Cleaning efficiency enhancement by ultrasounds for membranes used in dairy industries

  • Lujan Facundo, Maria Jose|||0000-0001-6871-0584
  • Mendoza Roca, José Antonio
  • Cuartas Uribe, Beatriz Elena|||0000-0003-2835-900X
  • Alvarez Blanco, Silvia
Membrane cleaning is a key point for the implementation of membrane technologies in the dairy industry for proteins concentration. In this study, four ultrafiltration (UF) membranes with different molecular weight cut-offs (MWCOs) (5, 15, 30 and 50 kDa) and materials (polyethersulfone and ceramics) were fouled with three different whey model solutions: bovine serum albumin (BSA), BSA plus CaCl2 and whey protein concentrate solution (Renylat 45). The purpose of the study was to evaluate the effect of ultrasounds (US) on the membrane cleaning efficiency. The influence of ultrasonic frequency and the US application modes (submerging the membrane module inside the US bath or applying US to the cleaning solution) were also evaluated. The experiments were performed in a laboratory plant which included the US equipment and the possibility of using two membrane modules (flat sheet and tubular). The fouling solution that caused the highest fouling degree for all the membranes was Renylat 45. Results demonstrated that membrane cleaning with US was effective and this effectiveness increased at lower frequencies. Although no significant differences were observed between the two different US applications modes tested, slightly higher cleaning efficiencies values placing the membrane module at the bottom of the tank were achieved., This work was supported by the Spanish Ministry of Science and Innovation (CTM 2010-20.186).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Cleaning of ultrafiltration membranes fouled with BSA by means of saline solutions

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
In this work, four ultrafiltration (UF) membranes with molecular weight cut-offs (MWCOs) of 5, 15, 30 and 50 kDa, respectively, were fouled with 1% BSA aqueous solutions and cleaned with different saline solutions. The influence of MWCO, membrane material and operating conditions on the cleaning effi- ciency was investigated. Saline solutions were able to clean the 5, 15 and 30 kDa membranes, but not the 50 kDa membrane. NaCl, NaNO3, NH4Cl and KCl were the most effective salts. The cleaning tests demonstrated that the higher the temperature of the saline solution was, the higher the cleaning efficiency was also. In addition, an increase in the crossflow velocity resulted in an increase in the hydraulic cleaning efficiency (HCE). However, there was an optimum value of salt concentration to clean the membrane effectively. Response Surface Methodology was used to investigate the relationship between salt concentration and temperature in the cleaning process., The authors of this work wish to gratefully acknowledge the financial support from the Spanish Ministry of Science and Innovation through the project CTM2010-20186 and the Generalitat Valenciana through the program "Ayudas para la realizacion de proyectos I+D para grupos de investigacion emergentes GV/2013".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Destabilization and removal of immobilized enzymes adsorbed onto polyethersulfone ultrafiltration membranes by salt solutions

  • Corbatón Báguena, María José
  • Gugliuzza, A.
  • Cassano, A.
  • Mazzei, R.
  • Giorno, L.
In this work the effectiveness of two saline solutions (NaCl and Na2SO4) to clean a permanently hydrophilic polyethersulfone (PESH) ultrafiltration (UF) membrane with a molecular weight cut-off (MWCO) of 30 kDa previously fouled with enzymatic solutions was investigated. The influence of protein concentration in the enzymatic solution during the fouling step and the effect of salt type during the cleaning procedure were studied. The protein aggregation was analyzed in solution and onto the membrane surface by using several techniques including Dynamic Light Scattering (DLS), Atomic Force Microscopy (AFM) and Infrared Spectroscopy with Attenuated Total Reflectance (ATR-FTIR). In addition, mechanisms that dominate membrane fouling were studied by fitting some mathematical models (Hermia's models adapted to crossflow filtration, a combined model based on the complete blocking and cake formation equations and a resistance-in-series model) to the experimental data. Fouling results showed that the complete blocking/adsorption on membrane surface was the predominant fouling mechanism. Regarding the cleaning results, higher cleaning efficiency and low residual protein concentration was obtained with NaCl solutions for all the feed solutions tested due to the favorable interaction between Cl and proteins., Maria-Jose Corbaton-Baguena wishes to gratefully acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness through the grant EEBB-I-14-09011 (project CTM2010-20186). The authors acknowledge the European Union, Fondo Europeo di Sviluppo Regionale, The Ministero dell'Istruzione, dell'Universita e della Ricerca - MIUR, The Ministero dello Svilupppo Economic - MSE - for the financial support to the project "Sistemi tecnologici avanzati e processi integrati della filiera olivicola per la valorizzazione dei prodotti e dei sottoprodotti, lo sviluppo di nuovi settori e la creazione di sistemi produttivi Eco-compatibili" (PON Olio Piu, PON01_01545), within the framework PON Ricerca e Competitivita 2007-2013.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Application of electric fields to clean ultrafiltration membranes fouled with whey model solutions

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
In this work, the effectiveness of electric fields to clean two ZrO2 TiO2 ultrafiltration (UF) membranes fouled with three types of whey model solutions was investigated. Membranes tested had different molecular weight cut-offs (MWCOs) (15 and 50 kDa). Whey model solutions consisted of aqueous solutions of bovine serum albumin (BSA) at 10 g/L, a mixture of BSA (10 g/L) and CaCl2 (1.65 g/L) and whey protein concentrate (WPC) (total protein content 45%) solutions at different concentrations (22.2, 33.3 and 150.0 g/L). The hydraulic cleaning efficiency (HCE) achieved by means of the application of the electric fields was evaluated as a function of the membrane MWCO and the operating conditions of the cleaning technique (applied potential, temperature of the cleaning solution and concentration of NaCl). The results demonstrated that the presence of NaCl favoured the removal of protein deposits on the membrane layer. On the other hand, the higher the temperature of the cleaning solution and the applied potential were, the higher HCE was achieved. Regarding the membrane MWCO, the permselective properties of the 15 kDa membrane were completely recovered after the cleaning procedure by electric field for all the feed fouling solutions tested, whereas this technique could not completely remove the protein deposits on the 50 kDa membrane when BSA solutions were used as feed., The authors of this work wish to gratefully acknowledge the financial support from the Spanish Ministry of Science and Innovation through the project CTM2010-20186 and the company MAGNETO Special Anodes B.V. for supplying the Ti-Ir electrode.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of two ultrafiltration fouling models and estimation of model parameters as a function of operational conditions

  • Corbatón Báguena, María José
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
  • Alvarez Blanco, Silvia
  • Lora-García, Jaime|||0000-0003-1699-5404
This work analyses the measure of fit of experimental data of permeate flux decline with time for ultrafiltration experiments performed with polyethylene glycol aqueous solutions to two different ultrafiltration models. A feed solution of 5 kg/m of polyethylene glycol and a monotubular ceramic membrane of - were used in the experiments. The first model considered was developed by Ho and Zydney and it considers two different fouling mechanisms: pore blocking and gel layer formation. The second model was proposed by Yee et al. It is an exponential model that considers three stages: concentration polarization, molecule deposition on the membrane surface and long-term fouling. The results show that both models give very accurate predictions for the severe fouling conditions (high transmembrane pressures and low crossflow velocities). However, both models cannot explain the experimental results obtained for all the experimental conditions tested. An equation for Ho and Zydney's model parameters as a function of operating conditions was obtained by means of multiple regression analysis., The authors of this work wish to gratefully acknowledge the financial support of the Universidad Politecnica de Valencia through the Project No. 2010.1009 and the Spanish Ministry of Science and Technology through the project CTM2010-20186.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Salt cleaning of ultrafiltration membranes fouled by whey model solutions

  • Corbatón Báguena, María José
  • Alvarez Blanco, Silvia
  • Vincent Vela, Maria Cinta|||0000-0001-8493-0165
In this work, three ultrafiltration (UF) membranes were fouled with whey model solutions that contained BSA (1% w/w) and CaCl2 (0.06% w/w). These membranes were cleaned with NaCl solutions. Temperature, crossflow velocity and concentration were varied. The membranes considered were a polyethersulfone (PES) membrane, a ceramic ZrO2–TiO2 membrane and a permanently hydrophilic polyethersulfone (PESH) membrane. Their molecular weight cut-offs (MWCOs) are 5, 15 and 30 kDa, respectively. The cleaning efficiency was related to the MWCO, membrane material and operating conditions. The results obtained demonstrated that NaCl solutions were able to clean the membranes tested. In addition, the higher the temperature and the crossflow velocity of the cleaning solution, the higher the cleaning efficiency was. However, there was an optimum value of NaCl concentration to clean the membranes effectively. When concentration was higher than the optimum, the cleaning efficiency decreased. The relationship between the cleaning efficiency and the operating conditions was obtained with statistical and optimization analysis., The authors of this work wish to gratefully acknowledge the financial support from the Spanish Ministry of Science and Innovation through the project CTM2010-20186 and the Generalitat Valenciana through the program "Ayudas para la realizacion de proyectos I+D para grupos de investigacion emergentes GV/2013".