Pasar al contenido principal

ESTRATEGIAS DE OPTIMIZACION DE PROCESOS DE OBTENCION DE BIOPRODUCTOS A PARTIR DE RESIDUOS ORGANICOS MEDIANTE FERMENTACION EN ESTADO SOLIDO

CTM2015-69513-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDAD AUTONOMA DE BARCELONA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 27
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

2-phenylethanol (rose aroma) production potential of an isolated pichia kudriavzevii through solid-state fermentation

  • Martínez Ávila, Óscar Mauricio|||0000-0001-7561-4013
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Barrena, Raquel|||0000-0002-6077-7765
2-phenylethanol (2-PE) is a higher alcohol widely used in industry that can be obtained by solid-state fermentation (SSF) using low-cost raw materials. This report describes the 2-PE production potential of an indigenous Pichia kudriavzevii isolated from solid-state fermented sugarcane bagasse that possesses attractive characteristics for processing waste streams such as its low-pH tolerance, high growth rate and temperature resistance. Besides, 2-PE production was optimized in batch-SSF using sugarcane bagasse supplemented with L-phenylalanine as substrate. Full factorial design allowed identifying the pH adjustment, micronutrient addition, inoculum and co-substrate load effects, and response surface methodology served to identify the maximum production based on temperature, initial moisture content (MC0) and specific airflow rate (SAFR). While the pH adjustment and micronutrient addition did not affect the 2-PE production, temperature and MC0 resulted critical for the process. After optimization, the maximum 2-PE content was 27.2 ± 0.2 mg per gram of dry substrate at 31 °C, 76 % MC0 and 0.129 L h-1 g-1 SAFR. This result was 23.8 % higher than the sub-optimal condition, and it is the highest 2-PE production via SSF reported so far. These results confirm the ability of P. kudriavzevii for producing 2-PE, and its potential for using waste streams as substrate.
Dipòsit Digital de Documents de la UAB
Publicación Artículo de revisión (ReviewArticle)

Bioprocesses for 2-phenylethanol and 2-phenylethyl acetate production, current state and perspectives

  • Martínez Ávila, Óscar Mauricio|||0000-0001-7561-4013
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Barrena, Raquel|||0000-0002-6077-7765
2-Phenylethanol (2-PE) and 2-phenethyl acetate (2-PEA) are valuable generally recognized as safe flavoring agents widely used in industry. Perfumes, pharmaceuticals, polishes, and personal care products, are some of the final products using these compounds as additives due to their rose-like odor. Also, 2-PE is used in disinfectants, pest control, and cleaning products due to its biocide capability. Although most of these additives production are derived from chemical synthesis, the current trend of consumers to prefer natural products has contributed to the development of biotechnological approaches as an alternative way to obtain natural 2-PE and 2-PEA. The most efficient route to bioproduce these compounds is through the bioconversion of L-phenylalanine via the Ehrlich pathway, and most of the advances have been focused on the development of this process. This review compiles the most recent developments in the biotechnological production of 2-PE and 2-PEA, indicating the most studied strains producing 2-PE and 2-PEA, the current advances in the in situ product recovery in liquid systems, an overview of the strain developments, and the progress in the use of residue-based systems. Future research should address the need for more sustainable and economic systems such as those using wastes as raw materials, as well as the scale-up of the proposed technologies.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Valorization of agro-industrial wastes by producing 2-phenylethanol via solid-state fermentation, influence of substrate selection on the process

  • Martínez Ávila, Óscar Mauricio|||0000-0001-7561-4013
  • Muñoz-Torrero, Patricia
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Barrena, Raquel|||0000-0002-6077-7765
2-phenylethanol (2-PE) is a value-added compound widely used in industry due to its rose-like odor and antibacterial properties that can be bioproduced using wastes as raw materials. This study presents the valorization of nine agro-industrial wastes as potential substrates for 2-PE production using an isolated 2-PE producer Pichia kudriavzevii, and the solid-state fermentation (SSF) technology as an alternative approach. The assessed substrates comprised wastes of varied traits such that each of them provided different characteristics to the fermentation. Thus, by using a principal component analysis (PCA), it was possible to identify the most significant characteristics associated with the substrates affecting the 2-PE production. Results show that L-phenylalanine biotransformation was more efficient than de novo synthesis for producing 2-PE. Besides, from the evaluated set, the maximum 2-PE production was achieved with red apple pomace, reaching 1.7 and 25.2 mg2PE per gram of used waste through de novo and L-phenylalanine biotransformation, respectively. In that scenario, volumetric productivity and precursor yield were 39.6 mg2PE L-1h-1 and 0.69 g2PE per gram of L-phenylalanine added, respectively. From the PCA, it was identified that the reducing sugars content of the substrate, the air-filled porosity of the bed and the L-phenylalanine availability were the most critical parameters (associated with the substrates) influencing the microbial activity and 2-PE production. These results suggest that the desirable traits a solid media needs for promoting 2-PE production via SSF could be reached by using a combination of wastes in a synergistic approach.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Fed-batch and sequential-batch approaches to enhance the bioproduction of 2-Phenylethanol and 2-Phenethyl Acetate in Solid-State Fermentation Residue-Based Systems

  • Martínez Ávila, Óscar Mauricio|||0000-0001-7561-4013
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Barrena, Raquel|||0000-0002-6077-7765
This study describes the use of alternative operational strategies in the solid-state fermentation of the agro-industrial leftover sugar cane bagasse (SCB) supplemented with l-phenylalanine, for bioproducing natural 2-phenylethanol (2-PE) and 2-phenethyl acetate (2-PEA) using K. marxianus. Here, fed-batch and sequential-batch have been assessed at two scales (1.6 and 22 L) as tools to increase the production, as well as to enhance the sustainability of this residue-based process. While in the reference batch strategy a maximum of 17 mg of 2-PE+2-PEA per gram of added SCB was reached at both scales, the implementation of fed-batch mode induced a production increase of 11.6% and 12.5%, respectively. Also, the production was increased by 16.9% and 2.4% as compared to the batch when a sequential-batch mode was used. Furthermore, the use of these strategies was accompanied by lower consumption of key resources like the inoculum, air, and time, promoting savings between 22% and 76% at both scales.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Solid-State Fermentation as a Novel Paradigm for Organic Waste Valorization, a Review

  • Abu Yazid, Noraziah|||0000-0002-8759-5435
  • Barrena, Raquel|||0000-0002-6077-7765
  • Komilis, Dimitrios|||0000-0002-6606-300X
  • Sánchez, Antoni|||0000-0003-4254-8528
The abundance of organic solid waste throughout the world has become a common issue that needs complete management at every level. Also, the scarcity of fuel and the competition between food and substance as an alternative to a petroleum-based product has become a major problem that needs to be properly handled. An urge to find renewable substances for sustainable development results in a strategy to valorize organic solid waste using solid state fermentation (SSF) and to manage the issue of solid wastes in a green approach. This paper reviews management of solid wastes using SSF, with regard to its current application, advantages and challenges, downstream processing in SSF, economic viewpoint, and future perspectives.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Production of sophorolipids from winterization oil cake by solid-state fermentation, optimization, monitoring and effect of mixing

  • Jiménez Peñalver, Pedro|||0000-0001-8923-3051
  • Gea, Teresa|||0000-0003-2523-4797
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
Sophorolipids (SLs) are a group of extracellular biosurfactants produced by the yeast Starmerella bombicola. The present study explored the use of winterization oil cake (WOC), a residual oil cake that comes from the oil refining industry, as a substrate for the production of SLs by solid-state fermentation (SSF). Sugar beet molasses (MOL) was used as a co-substrate and S. bombicola ATCC 22214 as the inoculum. Fermentation was performed on the 100-g scale and was optimized in terms of the ratio of substrates and the aeration rate using response surface methodology. The optimized SSF process (1:4 MOL:WOC mass ratio and 0.30 L kg⁻¹ min⁻¹ aeration rate), carried out under static conditions, was monitored for 10 days with a maximum SL yield of 0.179 g per g DM (dry matter). The effect of intermittent mixing on the process was also investigated. Mixing caused a 31% increase in SL production, with a total yield of 0.235 g per g DM. The Oxygen Uptake Rate (OUR) and the Cumulative Oxygen Consumption (COC) were used to monitor the biological activity of the fermentation processes. There were significant correlations between the SL yield and the oxygen and fats consumed. The SLs were characterized by FTIR and ¹H NMR analysis.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

The immobilisation of proteases produced by SSF onto functionalized magnetic nanoparticles, application in the hydrolysis of different protein sources

  • Abu Yazid, Noraziah|||0000-0002-8759-5435
  • Barrena, Raquel|||0000-0002-6077-7765
  • Sánchez, Antoni|||0000-0003-4254-8528
Alkaline proteases produced from protein-rich waste (hair waste and soya residues) by solid state fermentation (SSF) were immobilised onto functionalized magnetic iron oxide nanoparticles (MNPs) using glutaraldehyde as a crosslinking agent. The covalent binding method had a better immobilisation yield compared to simple adsorption, retaining 93%-96% (459 ± 106 U/mg nanoparticles, 319 ± 34 U/mg nanoparticles) of hair waste and soya residues proteases, respectively after crosslinking with 5% glutaraldehyde for 6 h. However, the adsorption immobilisation yield was 47%-54% after 8 h for both proteases. MNPs and immobilised proteases were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and electron diffraction. Our results indicated successful crosslinking between the proteases and amino-functionalized MNPs. The operational stability (pH and temperature) and storage stability of free and immobilised enzyme were also analysed. Despite the fact that the optimum pH of free and immobilised proteases was identical in the alkaline region, the immobilised proteases reached their optimum condition at higher temperatures (40 °C-60 °C). After 2 months of storage at 4 °C, the immobilised proteases showed good stability, retaining more than 85% of their initial activity. The high magnetic response of MNPs render an ease of separation and reusability, which contributes to the residual activity of both immobilised proteases on MNPs retaining more than 60% of their initial values after seven hydrolytic cycles. These results showed the enhancement of the stability of the crosslinking interactions between the proteases and nanoparticles. The immobilised proteases were capable of hydrolysing selected proteins (casein, oat bran protein isolate, and egg white albumin). However, differences in the degree of hydrolysis were observed, depending on the combination of the protease and type of substrate used.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Towards a competitive solid state fermentation, cellulases production from coffee husk by sequential batch operation and role of microbial diversity

  • Cerda Llanos, Alejandra Patricia|||0000-0001-8904-1586
  • Gea, Teresa|||0000-0003-2523-4797
  • Vargas-García, María del Carmen|||0000-0002-7647-3395
  • Sánchez, Antoni|||0000-0003-4254-8528
The cost of cellulases is the main bottleneck for bioethanol production at commercial scale. Solid-state fermentation (SSF) is a promising technology that can potentially reduce cellulases cost by using wastes as substrates. In this work, a SSF system of 4.5L bioreactors was operated continuously by sequential batch operation using the fermented solids from one batch to inoculate the following batch. Coffee husk was used as lignocellulosic substrate. Compost was used as starter in the first batch to provide a rich microbiota. Two strategies were applied: using 10% fermented solids as inoculum in 48h batches (SB90) and using 50% solids in 24h batches (SB50). A consistent and robust production process was achieved by sequential batch operation. Similar cellulase activities around 10 Filter Paper Units per gram of dry solids were obtained through both strategies. Microbial diversity in the starting materials and in the final fermented solids was characterized by next generation sequencing. Microbial composition of both fermented solids was similar but the relative abundance of families and species was affected by the operation strategy used. Main bacteria in the final solids came from compost (families Sphingobacteriaceae, Paenibacillaceae and Xanthomonadaceae), while main fungi families came from coffee husk (families Phaffomycetaceae, Dipodascaceae and two unidentified families of the class of Tramellomycetes). There was a high presence of non-identified mycobiota in the fermented solids. Main identified species were the bacteria Pseudoxanthonomas taiwanensis (12.3% in SB50 and 6.1% in SB90) and Sphingobacterium composti (6.1% in SB50 and 2.6% in SB90) and the yeasts Cyberlindnera jardinii and Barnettozyma californica (17.8 and 4.1% respectively in SB50 and 34 and 9.1% in SB90), all four previously described as lignocellulose degraders. The development of these operational strategies and further biological characterization of the end product could eventually benefit the process economics by providing a standard and specialized inoculum for a continuous SSF for cellulases production.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Solid state fermentation and composting as alternatives to treat hair waste, a LCA comparative approach

  • Catalán Campillo, Eva
  • Komilis, Dimitrios|||0000-0002-6606-300X
  • Sánchez, Antoni|||0000-0003-4254-8528
One of the wastes associated with leather production in tannery industries is the hair residue generated during the dehairing process. Hair wastes are mainly dumped or managed through composting but recent studies propose the treatment of hair wastes through solid-state fermentation (SSF) to obtain proteases and compost. These enzymes are suitable for its use in an enzymatic dehairing process, as an alternative to the current chemical dehairing process. In the present work, two different scenarios for the valorization of the hair waste are proposed and assessed by means of life-cycle assessment: composting and SSF for protease production. Detailed data on hair waste composting and on SSF protease production are gathered from previous studies performed by our research group and from a literature survey. Background inventory data are mainly based on Ecoinvent version 3 from software SimaPro® 8. The main aim of this study was to identify which process results in the highest environmental impact. The SSF process was found to have lower environmental impacts than composting, due to the fact that the enzyme use in the dehairing process prevents the use of chemicals traditionally used in the dehairing process. This permits to reformulate an industrial process from the classical approach of waste management to a novel alternative based on circular economy.
Dipòsit Digital de Documents de la UAB
Publicación Artículo de revisión (ReviewArticle)

A state of the art literature review on anaerobic digestion of food waste, influential operating parameters on methane yield

  • Komilis, Dimitrios|||0000-0002-6606-300X
  • Barrena, Raquel|||0000-0002-6077-7765
  • Grando, Rafaela Lora
  • Vogiatzi, Vasilia
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
A thorough literature review was conducted to investigate the behaviour of food waste in anaerobic digestion experiments. The main goal of this literature review was to study the effect of several operating parameters on methane yields and to develop a simplified regression equation to predict methane generation. Using a data prospection methodology, all the papers published within 2013-2015 that contained selected keywords were included in this study (a total of 613 papers). After screening, 167 papers were finally retrieved using the search engines and our methodology. From these papers, data from 231 experiments were recorded and evaluated. The parameters recorded in each paper were: operation mode (batch or continuous), temperature (mesophilic or thermophilic), moisture content (wet or dry), presence or absence of pretreatment, reactor scale (laboratory, bench, pilot, demonstration/full scale), presence or absence of co-substrates (co- or mono-digestion), organic loading rate, hydraulic retention time (HRT) and methane yield. The novelty of the work is that it employed various statistical tools to examine the effect of the above-mentioned factors on food waste methane generation. Most of the experiments were performed at mesophilic temperatures, at a wet system without substrate pretreatment. An equal number of papers described mono-digestion and co-digestion studies, and an equal number of papers described batch and continuous reactor experiments. The mean HRT for the continuous processes was 36.7 days. Statistical analysis indicated that the parameters that significantly affected methane yields were the "operation mode" and "pretreatment". A best reduced regression model was fitted to the methane yield data to describe the above effects. As a general conclusion, with this methodology, that involved the analysis of a large number of studies (with different conditions and set-ups, heterogeneous waste, etc.), correlations between some typical operating parameters of anaerobic digestion and methane yields were not obvious.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Valorization of sugarcane bagasse and sugar beet molasses using Kluyveromyces marxianus for producing value-added aroma compounds via solid-state fermentation

  • Martínez Ávila, Óscar Mauricio|||0000-0001-7561-4013
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Barrena, Raquel|||0000-0002-6077-7765
The growing demand for natural products has favored the development of bioprocesses for obtaining value-added products in the fragrance and flavor sector. Solid-state fermentation (SSF) of agro-industrial residues together with generally recognized as safe (GRAS) strains like Kluyveromyces marxianus appears as a remarkable alternative for producing aroma compounds. In this study, a continuous air supplied system was used for optimizing the production of fruit-like compounds via SSF of a mixture of sugarcane bagasse/sugar beet molasses employing K. marxianus. The main operational parameters were evaluated to identify the best conditions for their biosynthesis. Maximum cumulative volatile production was achieved at 40 °C, 35% molasses (dry basis) and specific air flow rate (SAFR) 0.14 L h⁻¹g⁻¹ITS reaching 161 mgTVOL per gram of initial total solids content (ITS). The main components of the produced volatiles were alcohols (43%) while ester species constituted only 18%. Selectivity to ester species was enhanced working at 30 °C, 25% molasses and SAFR 0.11 L h⁻¹g-1ITS, maximizing the ester content to 47.6 mgEster g⁻¹ITS. In this case, a pleasant fruity odor was perceived thanks to the higher ester content (35%). Stressing conditions for K. marxianus like high temperatures and limiting nitrogen availability seem to be key factors for promoting the production of the volatile compounds.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Technology overview of biogas production in anaerobic digestion plants, a European evaluation of research and development

  • Grando, Rafaela Lora
  • De Souza Antune, Adelaide Maria
  • Da Fonseca, Fabiana Valéria
  • Barrena, Raquel|||0000-0002-6077-7765
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
Anaerobic digestion (AD) technology is used commercially around the world, especially in Europe, which has set some challenging targets to diversify its energy mix with more renewable energy. This study intends to demonstrate, through technology prospecting, the relation between academic research (published articles) and technology development (patent applications) evolved from 1990 to 2015. Published articles were classified under the topics and wastes they cover, which include manure, agricultural and food waste, wastewater, sewage sludge and the organic fraction of municipal solid waste, with the last of these often being associated with co-digestion processes. Meanwhile, the patents in the area are mostly for equipment of the AD process and new methods or means of purifying the biogas obtained. It was found that the patents filed in Europe tend to protect their innovations only occasionally in countries outside the EU. Germany is the clear leader in all the areas of research and the commercial applications of the technologies, followed by Italy, Spain and Sweden. This study also demonstrates the immense potential of biogas throughout Europe, not just for energy generation, but also as a fuel and a by-product of the treatment of different kinds of waste.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

The effect of a short term aerobic pretreatment step on the anaerobic co-digestion of the organic fraction of municipal solid wastes, liquid extract addition versus solid phase addition

  • Martínez-Valdez, Francisco
  • Komilis, Dimitrios|||0000-0002-6606-300X
  • Saucedo-Castañeda, Gerardo
  • Barrena, Raquel|||0000-0002-6077-7765
  • Sánchez, Antoni|||0000-0003-4254-8528
Goal of the work was to study the effect of mixing aerobically pretreated organic municipal solid wastes (OFMSW) with raw OFMSW in an anaerobic digestion process. The optimum time of aerobic pretreatment was found to be five days, as this was indicated via biological activity measurements (oxygen uptake rate, enzymatic activities, temperature). The aerobically pretreated wastes or a liquid extract from those pretreated wastes were, each separately, mixed with simulated OFMSW in various experiments. The mixtures were anaerobically digested for 28 days and five different treatments were performed including the blanks. The methane generation results were fitted to a typical anaerobic model to calculate theoretical maximum methane potential, maximum methane generation rate and theoretical lag time. Results indicated that the addition of 5-day aerobically pretreated OFMSW in solid form to raw OFMSW resulted in a 18 % net increase of the methane production. The Rmax was also increased by 39 % while no significant differences in the lag time of the methanogenic phase were observed. The addition of the liquid extract that was obtained from the 5-day pretreated OFMSW did not result in a statistically significant increase of the net methane production of the raw OFMSW.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Composting of food wastes, status and challenges

  • Cerda Llanos, Alejandra Patricia|||0000-0001-8904-1586
  • Artola, Adriana|||0000-0002-0524-2119
  • Barrena, Raquel|||0000-0002-6077-7765
  • Font, Xavier|||0000-0003-4981-7436
  • Gea, Teresa|||0000-0003-2523-4797
  • Sánchez, Antoni|||0000-0003-4254-8528
This review analyses the main challenges of the process of food waste composting and examines the crucial aspects related to the quality of the produced compost. Although recent advances have been made in crucial aspects of the process, such composting microbiology, improvements are needed in process monitoring. Therefore, specific problems related to food waste composting, such as the presence of impurities, are thoroughly analysed in this study. In addition, environmental impacts related to food waste composting, such as emissions of greenhouse gases and odours, are discussed. Finally, the use of food waste compost in soil bioremediation is discussed in detail.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Cellulase and xylanase production at pilot scale by solid-state fermentation from coffee husk using specialized consortia, the consistency of the process and the microbial communities involved

  • Cerda Llanos, Alejandra Patricia|||0000-0001-8904-1586
  • Mejías, Laura|||0000-0003-0675-0702
  • Gea, Teresa|||0000-0003-2523-4797
  • Sánchez, Antoni|||0000-0003-4254-8528
Solid state fermentation is a promising technology however rising concerns related to scale up and reproducibility in a productive process. Coffee husk and a specialized inoculum were used in a 4.5L and then in 50L reactors to assess the reproducibility of a cellulase and hemicellulase production system. Fermentations were consistent in terms of cellulase production and microbial communities. The higher temperatures achieved when operating at 50L generated a shift on the microbial communities and a reduction of nearly 50% on cellulase production at pilot scale. In spite, an overall enzymatic production of 3.1±0.5FPUg⁻¹DM and 48±4Ug⁻¹DM for FPase and Xyl activities was obtained, respectively, with low deviation coefficients of 16 and 19% for FPase and Xyl production. Gaseous emissions assessment revealed an emission factor of 2.6·10⁻³kg volatile organic compounds per Mg of coffee husk and negligible NH₃, CH₄ and N₂O emissions.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A novel strategy for producing compost with enhanced biopesticide properties through solid-state fermentation of biowaste and inoculation with Bacillus thuringiensis

  • Ballardo, Cindy|||0000-0002-3509-1980
  • Barrena, Raquel|||0000-0002-6077-7765
  • Artola, Adriana|||0000-0002-0524-2119
  • Sánchez, Antoni|||0000-0003-4254-8528
In the framework of a circular economy, organic solid wastes are considered to be resources useful for obtaining value-added products. Among other potential uses, biodegradable wastes from agricultural, industrial, and domestic sources are being studied to obtain biopesticides through solid-state fermentation (SSF), mainly at the laboratory scale. The suitability of biowaste (source-selected organic fraction of municipal solid waste) for use as a substrate for Bacillus thuringiensis (Bt) growth under non-sterile conditions in a 10 L SSF reactor was determined in this study. An operational strategy for setting up a semi-continuous process yielding a stabilised organic compost-like material enriched with Bt suitable for use as a soil amendment was developed. Concentrations of 1.7·10⁷-2.2·10⁷ and 1.3·10⁷-2.1·10⁷ CFU g⁻¹ DM for Bt viable cells and spores, respectively, were obtained in the final material. As the results confirmed, Bt-enriched compost-like material with potential biopesticide properties can be produced from non-sterile biowaste.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Production and characterization of sophorolipids from stearic acid by solid-state fermentation, a cleaner alternative to chemical surfactants

  • Jiménez Peñalver, Pedro|||0000-0001-8923-3051
  • Castillejos, Marta
  • Koh, Amanda
  • Gross, Richard
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Gea, Teresa|||0000-0003-2523-4797
In this manuscript, we approach the production of biosurfactants as a cleaner alternative to the chemically-produced surfactants currently used in a wide range of industries. Sophorolipids are microbially produced biosurfactants of the glycolipid type that have entered the market in select applications such as detergent or cosmetic formulation ingredients. This study focuses on sophorolipid production by the yeast Starmerella bombicola from stearic acid (C18:0), a low-cost carbon source that is difficult to work with in submerged fermentation since it remains a solid due to its high melting temperature. Consequently, optimizations of solid-state fermentation inoculated with Starmerella bombicola were studied for conversions of stearic acid and molasses to sophorolipids. Polyurethane foam functioned as the inert support. The effect of polyurethane foam density and water holding capacity was assessed and the process was optimized in terms of substrate and inoculum ratio. The best conditions were: foam with a density of 32 kg m-3 at 75% water holding capacity, 1.17:1 molasses/stearic acid (w/w) and 5% (v/w) inoculum, to obtain a yield of 0.211 g sophorolipids per g of substrates. Mass spectrometry revealed that the sophorolipids produced herein had high concentrations of diacetylated acidic and lactonic C18:0 forms. The results of interfacial properties studies revealed that C18:0 sophorolipids had promising surface tension lowering capacity and emulsification behavior. This study describes a new strategy to produce biosurfactants using low environmental impact technologies as an alternative to traditional ways to produce chemical detergents.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A life cycle assessment on the dehairing of rawhides, chemical treatment versus enzymatic recovery through solid state fermentation

  • Catalán Campillo, Eva
  • Komilis, Dimitrios|||0000-0002-6606-300X
  • Sánchez, Antoni|||0000-0003-4254-8528
The leather industry needs to switch from the traditional chemically based dehairing process to an environmentally friendly one so that the overall burdens to the environment are reduced. The primary goal of the work was thus to compare the chemical leather dehairing process to an enzymatically based one using the enzymes that are extracted after the application of solid state fermentation (SSF) on hair wastes generated after dehairing. The environmental burdens of the dehairing stage were determined using a life cycle assessment (LCA) approach by comparing the two aforementioned management scenarios. The first scenario was the commonly used technology in which hair is removed via a chemical process and then composted in open piles. This scenario included two subscenarios where hair waste is either incinerated or landfilled. In the second scenario, the proteolytic enzymes extracted during the SSF of the residual hair are used to dehair the new rawhides instead of chemicals. Industrial and laboratory data were combined with international databases using the SimaPro 8.0 LCA software to make comparisons. The environmental impacts associated with the enzymatic dehairing were significantly lower than the ones associated to the conventional chemical dehairing process. This difference is attributed to the impacts associated with the original production of the chemicals and to the electricity consumed in the conventional method. A sensitivity analysis revealed that the results are affected by the amounts of chemicals used during dehairing.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Production of proteases from organic wastes by solid-state fermentation, downstream and zero waste strategies

  • Marín, Maria
  • Artola, Adriana|||0000-0002-0524-2119
  • Sánchez, Antoni|||0000-0003-4254-8528
Production of enzymes through solid-state fermentation (SSF) of agro-industrial wastes reports high productivity with low investment. The extraction of the final product from the solid waste and solid disposal represent the main cost of the process. In this work, the complete downstream processes of SSF of two industrial residues for the production of proteases, soy fibre (SF) and a mixture of hair and sludge (HS), were studied in terms of activity recovery, using different extraction parameters (extracting solvent, ratio solid: solvent and extraction mode). Activity after lyophilisation was tested. Solid waste valorisation after extraction was studied using respiration techniques and biogas production tests, as part of a zero waste strategy. Results showed a maximum extraction yield of 91% for SF and 121% for HS, both in agitated mode and distilled water as extraction agent. An average activity recovery of 95 ± 6 and 94 ± 6% for SF and HS, respectively, was obtained after lyophilisation and redissolution. To reduce the cost of extraction, a ratio 1:3 w:v solid-solvent in static mode is advised for SF, and 1:2 w:v extraction ratio in agitated mode for HS, both with distilled water as extracting agent. Both composting and anaerobic digestion are suitable techniques for valorisation of the waste material.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Bioproduction of 2-phenylethanol and 2-phenethyl acetate by Kluyveromyces marxianus through the solid-state fermentation of sugarcane bagasse

  • Martínez Ávila, Óscar Mauricio|||0000-0001-7561-4013
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Barrena, Raquel|||0000-0002-6077-7765
2-Phenylethanol (2-PE) and 2-phenethyl acetate (2-PEA) are important aroma compounds widely used in food and cosmetic industries due to their rose-like odor. Nowadays, due to the growing demand for natural products, the development of bioprocesses for obtaining value-added compounds has become of great significance. 2-PE and 2-PEA can be produced through the biotransformation of L-phenylalanine using the generally recognized as safe strain Kluyveromyces marxianus. L-phenylalanine bioconversion systems have been typically focused on submerged fermentation processes (SmF), but there is no information about other alternative productive approaches. Here, the solid-state fermentation (SSF) of sugarcane bagasse supplemented with L-phenylalanine was investigated as a sustainable alternative for producing 2-PE and 2-PEA in a residue-based system using Kluyveromyces marxianus as inoculum. An initial screening of the operational variables indicated that air supply, temperature, and initial moisture content significantly affect the product yield. Besides, it was found that the feeding strategy also affects the production and the efficiency of the process. While a basic batch system produced 16 mgproducts per gram of residue (dry basis), by using split feeding strategies (fed-batch) of only sugarcane bagasse, a maximum of 18.4 mgProducts g-1residue were achieved. Increase in product yield was also accompanied by an increase in the consumption efficiency of nutrients and precursor. The suggested system results as effective as other more complex SmF systems to obtain 2-PE and 2-PEA, showing the feasibility of SSF as an alternative for producing these compounds through the valorization of an agro-industrial residue.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhancing the bioproduction of value-added aroma compounds via solid-state fermentation of sugarcane bagasse and sugar beet molasses, operational strategies and scaling-up of the process

  • Martínez Ávila, Óscar Mauricio|||0000-0001-7561-4013
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Font, Xavier|||0000-0003-4981-7436
  • Barrena, Raquel|||0000-0002-6077-7765
Bioproduction of generally recognized as safe (GRAS) products starting with low-cost raw materials has become significant in the biorefinery concept. Thus, the solid-state fermentation (SSF) of agro-industrial residues using GRAS strains appears as alternative to obtain aroma compounds. Here, the SSF of the mixture sugarcane bagasse/sugar beet molasses was used for producing a mixture of value-added fruit-like compounds. The study aimed to enhance the production and ester selectivity evaluating three operational strategies at three scales (0.5, 4.5 and 22 L) using non-sterilized residues. While the average total volatile production was 120 mgVol per gram of dry substrate (g⁻¹ITS), fed-batch operation promoted the highest increases in the ester content up to 57 mgEst g⁻¹ITS, an 88 and 59% more than in the static-batch and intermittent mixing modes respectively. Alternative operational strategies have compensated the scale-up adverse effects in the bioproduction, moving towards a sustainable large-scale application in a circular economy scheme.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Optimization of down-stream for cellulases produced under solid-state fermentation of coffee husk

  • Marín, Maria
  • Artola, Adriana|||0000-0002-0524-2119
  • Sánchez, Antoni|||0000-0003-4254-8528
This work systematically studies the downstream process of the solid state fermentation (SSF) of a mixture of coffee husk and wood chips, inoculated with compost, for cellulase production. Downstream of SSF (at pilot scale) remains as one of the less studied stages of the process, being critical in technical, environmental and economic terms. In this study, the specific downstream points considered were: (i) enzyme extraction yield, in terms of extraction ratio solid:solvent, agitation mode and solvent type; (ii) enzymatic activity recovery of the lyophilised extract and (iii) efficiency of consecutive extractions. Results indicate a maximum activity recovery of 108 ± 30% in the extraction performed at ratio 1:5 solid-solvent, in static mode and with distilled water. Statistical analysis revealed a high dispersion of the results and needs to be considered to extract consistent conclusions in any downstream of SSF. Lyophilisation demonstrated to be an adequate technology for enzymatic activity preservation. Regarding consecutive extractions, yield recovery in the first and second extraction maintain a similar value. In a framework of a zero-waste enzyme production process, different strategies have been tested for the remaining solid after extraction. Respirometric tests reveal that it is possible to aerobically stabilize the remaining solid obtaining a compost like material, whereas anaerobic digestion resulted in low methane yields (51 ± 3 mL methane g-1 VS).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Long term enhanced solid-state fermentation, inoculation strategies for amylase production from soy and bread wastes by Thermomyces sp. in a sequential batch operation

  • Cerda Llanos, Alejandra Patricia|||0000-0001-8904-1586
  • El-Bakry, Mamdouh|||0000-0002-7523-3795
  • Gea, Teresa|||0000-0003-2523-4797
  • Sánchez, Antoni|||0000-0003-4254-8528
The effect of two thermophilic amylase producing strains was evaluated using different mixtures of soy and bread wastes. Thermomyces sp. was found to be better inoculum than Geobacillus sp. for a soy and bread waste mixture (90:10 w/w respectively) producing a maximum enzyme activity of 39.9·103 U g-1 dry substrate. Three strategies (a, b, c) were evaluated for solid-state fermentation (SSF) operation in sequential batches. Fermented solids from each batch were used to inoculate the following batch: (a) solids at the moment of maximum biological activity; (b) final solids (end of the process, maximum amylase production); (c) final solids after enzymatic extraction. The evaluated strategies led to an increase in amylase production of 50, 500 and 98% for each strategy, respectively. This indicates the suitability of fermented solids to act as inoculum and the enhancement of amylase production compared to traditional batches. As one of the main challenges of SSF is the maintenance of a productive process along time, these results confirm SSF as an excellent option to produce amylases from organic wastes.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Glutamic acid independent production of bioflocculants by bacillus subtilis UPMB13

  • Zulkeflee, Zufarzaana
  • Shamsuddin, Zulkifli
  • Aris, Ahmad Zaharin
  • Yusoff, Mohd Kamil
  • Komilis, Dimitrios|||0000-0002-6606-300X
  • Sánchez, Antoni|||0000-0003-4254-8528
Bacillus subtilis UPMB13 was found to be an L-glutamic acid independent producer of extracellular polymeric substances (EPS) with bioflocculation properties. Optimum production of the bioflocculant was found to be at the early stage of cell propagation of 24-72 h of fermentation. At a limited nutrient input of 100 mL tryptic soy broth, the flocculating activities were found to be negatively correlated (p < 0.01) with growth as it continued to decline after 72 h, while cell growth proliferated further. Ample nutrient supply may prolong bioflocculant production with flocculating activities of 90 % and higher, while excess oxygen supply may promote rapid growth that can lead to poor flocculation due to the re-use of the bioflocculant as a substitute for food during starvation. Bioflocculant production occurred at best at 25-30 °C incubation temperature and at the initial pH medium of 7 to 8. The bioflocculant was proven to be extracellularly produced as the broth and the supernatant possessed the ability to flocculate the suspended kaolin particles. Bioflocculant productions by UPMB13 were hereditarily stable among succeeding progenies, hence, proving genetic competency. About 0.90 g of purified bioflocculant were collected from 1 L culture broth of UPMB13 under the optimized fermentation conditions.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A review on anaerobic digestion of lignocellulosic wastes, Pretreatments and operational conditions

  • Sayara, Tahseen
  • Sánchez, Antoni|||0000-0003-4254-8528
Anaerobic digestion (AD) has become extremely popular in the last years to treat and valorize organic wastes both at laboratory and industrial scales, for a wide range of highly produced organic wastes: municipal wastes, wastewater sludge, manure, agrowastes, food industry residuals, etc. Although the principles of AD are well known, it is very important to highlight that knowing the biochemical composition of waste is crucial in order to know its anaerobic biodegradability, which makes an AD process economically feasible. In this paper, we review the main principles of AD, moving to the specific features of lignocellulosic wastes, especially regarding the pretreatments that can enhance the biogas production of such wastes. The main point to consider is that lignocellulosic wastes are present in any organic wastes, and sometimes are the major fraction. Therefore, improving their AD could cause a boost in the development in this technology. The conclusions are that there is no unique strategy to improve the anaerobic biodegradability of lignocellulosic wastes, but pretreatments and codigestion both have an important role on this issue.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Fungal biopesticide production, process scale-up and sequential batch mode operation with Trichoderma harzianum using agro-industrial solid wastes of different biodegradability

  • Sala, Arnau|||0000-0001-7010-6984
  • Barrena, Raquel|||0000-0002-6077-7765
  • Sánchez, Antoni|||0000-0003-4254-8528
  • Artola, Adriana|||0000-0002-0524-2119
This work presents a sequential batch operational strategy (SBR) for fungal conidia production in solid-state fermentation (SSF) to improve the traditional batch operation, while also aiming to present a robust and scalable process. Trichoderma harzianum was fermented using two substrates with different biodegradability (rice husk and beer draff), scaling from 1.5 L to 22 L bioreactors. Before the SBR operation, the optimum time to get inoculum from each SBR batch was determined as 4 days. While single batch process scale-up was successful with both substrates, SBR strategy was only feasible using beer draff as substrate: conidia production was sustained during 3 consecutive batches in 1.5 L bioreactors and for 5 batches at 22 L. At both scales conidia production was around 2.0x109 conidia g-1dm, achieving maximum specific oxygen consumption rate (sOUR) values close to 4 g O2 kg-1dm h-1 in most reactors. Air filled porosity was found as a key parameter regarding process scale-up, with a minimum value of 80% as necessary to proper scaling up to 22 L. Process robustness was statistically demonstrated as no significant differences in conidia production, moisture and pH were found at different reactor heights using both substrates in most 22 L reactors tests. Consequently, SBR operation has been presented as a reproducible method to overcome traditional packed-bed drawbacks while also improving SSF performance in comparison to traditional industrial SSF processes.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Insights on fungal solid-state fermentation for waste valorization, conidia and chitinase production in different reactor configurations

  • Sala, Arnau|||0000-0001-7010-6984
  • Echegaray, T.
  • Palomas, G.
  • Boggione, M. J.
  • Tubio, G.
  • Barrena, Raquel|||0000-0002-6077-7765
  • Artola, Adriana|||0000-0002-0524-2119
Different reactor configurations are paired with a wide variety of agro-industrial wastes of different biodegradability to produce fungal conidia by solid-state fermentation. This work presents a preliminary comparative study between packed-bed and tray reactor configurations to produce Beauveria bassiana and Trichoderma harzianum conidia using two different substrates in terms of biodegradability: rice husk or beer draff complemented with wood chips. Conidia production, mean temperature and respiration indexes have been analysed in most of the presented reactor configurations. Both strains showed higher conidia production when using beer draff complemented with wood chips as substrate due to the use of a mixture as substrate. When working with beer draff, chitinase analyses obtained similar profiles in both strains but higher overall values using TH. Conidia and chitinase production maximums were not achieved at the same time, having 2-3 days of difference depending on the strain. No significant differences in mean temperature were shown between most of the performed fermentations. As a result of the present work, further scaling of both packed bed and tray configurations using beer draff and wood chips to produce BB or TH conidia would be advisable. More experiments should be performed to optimize both conidia and chitinase productions to enhance the quality of the final product.