Pasar al contenido principal

DESARROLLO DE CATALIZADORES BASADOS EN OXIDOS METALICOS NO ESTEQUIOMETRICOS DE MO Y W CON PROPIEDADES ACIDAS Y/O REDOX PARA PROCESOS DE QUIMICA SOSTENIBLE

CTQ2009-14495

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2009
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Selective oxidative dehydrogenation of ethane over SnO2-promoted NiO catalysts

  • Solsona Espriu, Benjamin Eduardo
  • Demicol, B.
  • Hernández Morejudo, Selene
  • Delgado, J. J.
  • Calvino, J. J.
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] Ni-Sn-O mixed oxides catalysts have been investigated for the oxidative dehydrogenation of ethane. The catalysts were prepared through the evaporation of aqueous solutions of nickel nitrate and tin oxalate and finally calcined in air at 500 degrees C for 2 h. These materials have been characterized by several techniques (N-2-adsorption, X-ray diffraction, High-Resolution Electron Microscopy, temperature programmed reduction, X-Ray Photoelectron Spectroscopy, Fourier Transformed Infrared Spectroscopy of adsorbed CO and O-18/O-16 isotope exchange). The addition of just a tiny amount of tin highly increases the selectivity to ethylene (from ca. 40% to 80-90%). Thus, high selectivity to ethylene (near to 90%) is observed on samples with high Ni/Sn atomic ratios (3 < Ni/Sn <50), in which no influence of ethane conversion on selectivity to ethylene is observed (suggesting high stability of ethylene on these catalysts). Additionally, for low Sn-loadings, an increase in the catalytic activity has also been observed. The enhanced catalytic properties have been explained in terms of changes in the nature of Ni species on the catalyst surface, which can be considered as the active sites. The nature of Ni species is related to changes in the crystal size of NiO particles (and surface area) of catalysts as well as to the presence of SnOx crystals. In addition, the role of the presence of acid sites on the catalyst surface on the selectivity to ethylene is also discussed. (C) 2012 Elsevier Inc. All rights reserved., The authors would like to thank the DGICYT in Spain (Project CTQ2009-14495 and MAT2008-00889-NAN) for financial support. SH thanks a fellowship from DGICYT.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tungsten-Vanadium mixed oxides for the oxidehydration of glycerol into acrylic acid

  • Soriano Rodríguez, Mª Dolores|||0000-0002-1799-895X
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • López Nieto, José Manuel|||0000-0002-6960-3219
  • Cavani, Fabrizio
  • Guidetti, Stefania
  • Trevisanut, C.
[EN] In this paper we report on the one-pot transformation of glycerol into acrylic acid, catalyzed by W/V mixed oxides, with hexagonal tungsten bronze (HTB) structure. The reaction requires two different catalyst functions, i.e., an acid one, which is given by W oxide, and an oxidizing one, given by the V ions incorporated within the WO3 lattice. W¿O bronze is very active and moderately selective in acrolein formation, but yields only traces of acrylic acid. The incorporation of increasing amounts of V inside the hexagonal tungsten bronze structure, with the development of a monophasic compound, allows the consecutive oxidation of acrolein into acrylic acid. An optimal atomic ratio between W and V equal to V/(W + V) = 0.12¿0.21 made it possible to obtain an acrylic acid yield of 25% (with selectivity to residual acrolein of 11%). However, during reaction under the oxygen-containing feed, the V4+ incorporated into the hexagonal bronze structure underwent a slow oxidation into V5+, which caused a progressive decline of selectivity to acrylic acid and a concomitant increase of COx formation; the hexagonal structure however was stable during lifetime experiments. On the other hand, in the absence of oxygen a very rapid deactivation of the catalyst occurred, with a decrease in selectivity to acrolein and increase in heavy by-products., The Spanish authors would like to thank the DGICYT in Spain (Project CTQ2009-14495) for financial support. MIUR (Ministerro dell'Universita e della Ricerca) is acknowledged for the PhD grant to SG. M. D. S. thanks the Programa de Apoyo a la Investigacion y Desarrollo (PAID-00-10, Universidad Politecnica de Valencia, Spain) by concession of a short stay grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Oxidative dehydrogenation of ethane over Ni-W-O mixed metal oxides catalysts

  • Solsona Espriu, Benjamin Eduardo
  • Dejoz, A.
  • Ivars Barceló, Francisco
  • Vazquez, M. I.
  • López Nieto, José Manuel|||0000-0002-6960-3219
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
Ni-W-O mixed oxides were prepared through the evaporation of aqueous solutions of nickel nitrate and ammonium tungstate and calcined in air at 500 degrees C for 2 h. The catalysts were characterized by several techniques (N(2) adsorption, X-ray diffraction, temperature-programmed reduction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy of adsorbed CO, and (18)O/(16)O isotope exchange) and tested in the oxidative dehydrogenation of ethane. The catalytic activity and catalyst reducibility decrease when the W content increases. Thus, nickel sites seem to be the active centers for ethane activation in these catalysts. However, the selectivity to ethylene strongly changes depending on the Ni/W ratio. In W-rich catalysts, in which NiWO(4) and WO(3) are mainly observed, a strong influence of ethane conversion on the selectivity to ethylene is observed. However, in Ni-rich catalysts, in which NiO crystallites and WO(x) nanoparticles are mainly observed, ethane conversion hardly influences the selectivity to ethylene. It has been demonstrated that the nature of the Ni sites and the characteristics and number of the acid sites determine the catalytic behavior of these catalysts. The presence of Lewis acid sites with high acid strength in W-rich catalysts facilitates the decomposition of ethylene during ethane oxidation. (C) 2011 Elsevier Inc. All rights reserved., Financial support from DGICYT in Spain (Project CTQ-2009-14495) and Generalitat Valenciana (ACOMP/2010/091) is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Catalytic VOCs elimination over copper and cerium oxide modified mesoporous SBA-15 silica

  • Tsoncheva, Tanya
  • Issa, Gloria
  • Dimitrov, M.
  • Popova, Margarita
  • Hernández Morejudo, Selene
  • Kovacheva, Daniela
  • Atanasova, Genoveva
  • Blasco Lanzuela, Teresa|||0000-0002-8115-4241
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] Copper and cerium oxide bi-component materials with different Cu/Ce ratio were prepared using ordered SBA-15 silica as a support and compared with their bulk analogs. The samples were characterized by nitrogen physisorption, XRD, UV-Vis, FTIR, XPS, Raman spectroscopy and TPR with hydrogen. Cyclohexanol conversion was used as a catalytic test to obtain more information for the surface properties of the supported materials. The catalytic properties of the samples were studied in VOCs oxidation using toluene and ethyl acetate as probe molecules. A strong effect of mesoporous silica support and samples composition on the formation of catalytic sites was established. (C) 2012 Elsevier B.V. All rights reserved., Financial support of Bulgarian Academy of Science and National Scientific Fond of Ministry of Education Projects DTK 02/64 and ДНTC/Киtай 01/8, financial support from DGICYT in Spain (Project CTQ-2009-14495) and bilateral project Bulgarian-Spain Inter-academic Exchange Agreement (Project 2009BG0002) are acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Oxidative dehydrogenation of ethane over NiO-CeO2 mixed oxides catalysts

  • Solsona Espriu, Benjamin Eduardo
  • Hernández Morejudo, Selene
  • Demicol, Benjamin
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] In this paper we present the synthesis, characterization and catalytic behaviour in the oxidative dehydrogenation of ethane of NiO-CeO2 mixed oxides. The addition of cerium oxide to NiO strongly modifies its catalytic performance, although the changes in the catalytic behaviour depend on the catalyst composition. The incorporation of low amounts of cerium oxide to NiO multiplies the productivity to ethylene in the oxidative dehydrogenation of ethane by a factor of ca. 7, which is the result of an increase in both catalytic activity and selectivity to ethylene. The enhanced activity has been related to the remarkable increase of the surface area of catalyst and the low crystal sizes of NiO that takes place when a tiny amount of cerium oxide is incorporated to the NiO. The higher selectivity to ethylene has been related to the modification of the nature of Ni-O species, which implies a lower production of carbon oxides. On the other hand, high activity and selectivity is also observed over catalysts rich in cerium ( with Ni/ Ce ratios between 0.2 and 3). In this case, a different mechanism can be proposed in which the high capacity of CeO2 to bomb oxygen from bulk to surface and the partial formation of NiO and Ce1-xNixO2 facilitates a faster reoxidation of active Ni-sites by a synergic effect improving catalytic activity. (C) 2011 Elsevier B.V. All rights reserved., The authors would like to thank the DGICYT in Spain (Project CTQ2009-14495) for financial support. SH thanks a fellowship from DGICYT.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Glycerol oxidehydration into acrolein and acrylic acid over W-V-Nb-O bronzes with hexagonal structure

  • Chieregato, Alessandro
  • Basile, Francesco
  • Guidetti, Stefania
  • Liosi, Giuseppe
  • Trevisanut, Cristian
  • Cavani, Fabrizio
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • Soriano Rodríguez, Mª Dolores|||0000-0002-1799-895X
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] This paper deals with an investigation of hexagonal W-Nb-O and W-V-Nb-O bronzes as catalysts for the one-pot oxidehydration of glycerol into acrylic acid. In a previous work, we reported that the best yield to acrylic acid obtained with the W-V-O bronze was 25%; in the current work, the incorporation of Nb in the tri-component bronze structure allowed us to obtain the best acrylic acid yield of 34%. The W-Nb-O bronze was an efficient acid catalyst for the dehydration of glycerol into acrolein - more selective than WO3 at temperatures lower than 300 degrees C -, whereas in the tri-component system the presence of V conferred to the catalyst the redox properties for the partial oxidation of acrolein into acrylic acid. The characterization of the catalysts confirmed the incorporation of Nb5+ in the hexagonal structure, and the generation of acid sites with enhanced strength compared to the bi-component W-V-O system. This also enhanced the stability of catalytic performance during short-term lifetime experiments. (C) 2012 Elsevier B.V. All rights reserved., CIRI (Centro Interdipartimentale per la Ricerca industriale, Universita di Bologna) Energia e Ambiente is acknowledged for the research grant assigned to Alessandro Chieregato. MIUR (Ministero dell'Universita e della Ricerca Scientifica) is acknowledged for the PhD grant to Stefania Guidetti (Progetto Giovani). MIPAAF (Ministero delle Politiche Agricole Alimentari e Forestali) is acknowledged for partially financing the project (Progetto Extravalore, PNR 2005-2007). Financial support from DGICYT in Spain (Project CTQ-2009-14495) and Generalitat Valenciana (ACOMP/2010/091) is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Iron-containing SBA-15 as catalyst for partial oxidation of hydrogen sulfide

  • Reyes-Carmona, Alvaro
  • Jones, Deborah J.
  • Jimenez-Jimenez, Jose
  • Jimenez-Lopez, Antonio
  • Rodriguez-Castellon, Enrique
  • Soriano Rodríguez, Mª Dolores|||0000-0002-1799-895X
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] A family of Fe-containing SBA-15 silica synthesized by a simple one-pot hydrothermal method was synthesized and tested in the hydrogen sulfide partial oxidation for sulfur production at 200 degrees C and atmospheric pressure. All these materials maintain the porous hexagonal structure of SBA-15 showing a good chemical and mechanical stability. Isolated Fe3+ species are mainly observed at high Si/Fe ratio (ca. 40). However, extra framework iron oligomers and/or aggregated iron oxide clusters are mainly observed for samples with Si/Fe ratio lower than 10. High H2S conversion and high selectivity to sulfur (higher than 99%), with very low selectivity to SO2 (lower than 0.5% at H2S conversion between 60 and 80%), have been achieved. Moreover, the TOF decreases when increasing the amount of iron in the catalysts. (C) 2012 Elsevier B. V. All rights reserved., Financial support from MINECO in Spain through Project MAT2009-10481 and FEDER funds and Project CTQ2009-14495 are gratefully acknowledged. Junta de Andalucía through excellence project P09-FQM 5070 is also acknowledged. MDS thanks a fellowship from the Universidad Politécnica of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structural Characterization of Zeolites by Advanced Solid State NMR Spectroscopic Methods

  • Mafra, Luis
  • Vidal Moya, José Alejandro
  • Blasco Lanzuela, Teresa|||0000-0002-8115-4241
[EN] This review overviews the application of solid state NMR spectroscopy to the structural characterization of silicate, and acidic aluminosilicate and borosilicate zeolites focusing on the utilization of new developed methods. We summarize recent results on the investigations of the distribution of silicon atoms into the zeolite framework, as well as the location of F¿ anions and formation of pentacoordinated silicon species in zeolites synthesized in fluoride medium. Special attention is paid here to the characterization of framework and extraframework boron and most specially aluminium species and the acid sites in zeolites. In Section 6 of this review, we present the basis and practical aspects of advanced NMR experiments used in the characterization of microporous solids paying special attention to quadrupolar nuclei and other methods based on dipolar interactions., J. A. V.-M. and T. B. acknowledge Spanish MICINN (Projects MAT-2009-14528-C02-01; CTQ-2009-14495), Consolider-Ingenio 2010-Multicat and Generalitat Valenciana (GV PROMETEO/2008/130) for financial support during the elaboration of this chapter. L. M. thanks FCT, QREN, COMPETE, and EU for financial support. The Portuguese NMR Network (RNRMN) is acknowledged. F. C. T. is also acknowledged for other funding, R&D Project PTDC/QUI-QUI/100998/2008. L. M. also greatly acknowledges the Campus de Excelencia Internacional Ad Futurum de la Universidad de Oviedo (FUTTALENT Program).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Lignocellulosic-derived mesoporous materials: an answer to manufacturing non-expensive catalysts useful for the biorefinery processes

  • Guerrero-Perez, M. O.
  • Valero-Romero, M. J.
  • Hernández Morejudo, Selene
  • Rodriguez-Mirasol, J.
  • Cordero, T.
  • López Nieto, José Manuel|||0000-0002-6960-3219
The synthesis procedure and characterization of a mesoporous carbon obtained from biomass waste by a simple method, generating a low-cost material, with the corresponding waste revaluation are described. The use of phosphoric acid during the activation of the waste material induces the presence of stable phosphate groups, with acid characteristics, on the surface of the mesoporous carbon, which could find many applications as an acid solid catalyst. In addition, such phosphate groups increase the stability of the carbon material under oxidizing conditions at relatively high temperatures, increasing the range of catalytic applications in which this material could be used. This paper also shows how the redox functionality can be incorporated on the surface of this carbon material by impregnation with vanadium oxide species. The corresponding carbon supported vanadium oxide catalyst is active and relatively selective in the propylene partial oxidation to oxygenates. It is also discussed how the catalytic behavior of such vanadium-containing catalysts can be improved by the use of Zr as dopant. (C) 2012 Elsevier B. V. All rights reserved., This work was supported by the Spanish Ministry of Education and Science (CTQ-2009-14262 and CTQ-2009-14495). M.J.V.-R. thanks the Spanish Ministry of Science and Innovation for her FPI predoctoral fellowship; and M.O. G.-P. is indebted to Junta de Andalucia (Incentivos Estancias de Excelencia 2/2009) for financial support during her stay at ITQ-CSIC. Thanks are extended to the organizers of the CatBior Conference and guest editors of this special issue, Profs. Manuel Lopez-Granados and Pedro Maireles.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Alkali-promoted V2O5 catalysts for the partial oxidation of H2S to sulphur

  • Soriano Rodríguez, Mª Dolores|||0000-0002-1799-895X
  • López Nieto, José Manuel|||0000-0002-6960-3219
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • Ivars Barceló, Francisco
  • Rodriguez-Castellon, E.
[EN] Present paper describes the influence of the incorporation of alkali metal cations (AM = Li, Na, K, Cs; and an AM/V ratio of 0.04) and Na-content (Na/V ratio of 0.02-0.30) in alkali metal promoted V2O5 catalyst on both the catalyst structure and the catalytic performance in H2S partial oxidation reactions. The catalytic activity depends on the alkali metal and the amount of alkali metal added, although Na-containing catalysts seem to be the more active ones. However, selectivity to sulphur higher than 98% is achieved in the main of catalysts when working at reaction temperature lower than 220 degrees C. According to the characterization results of used catalysts, V4O9 is selectively formed during the catalytic tests on catalysts presenting V2O5 crystallites. In catalysts with Na/V ratios higher than 0.04, V4O9 and Na0.33V2O5 are observed, the presence of Na0.33V2O5 increasing when increasing the Na/V ratio. Accordingly, V4O9 and Na0.33V2O5 can be proposed as the active and selective crystalline phase in Na-containing catalysts. The role of the presence of V4+-O-V5+ pairs in partial oxidation of H2S is also discussed. (c) 2012 Elsevier B.V. All rights reserved., Financial support from DGICYT in Spain through Project CTQ2009-14495 and Project MAT2009-10481 and FEDER funds are gratefully acknowledged. MDS thanks a fellowship from the Universidad Politecnica of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Partial Oxidation of H(2)S to Sulfur Over Mo and/or W-Containing Bronzes with a TTB-Structure

  • Soriano Rodríguez, Mª Dolores|||0000-0002-1799-895X
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • BOTELLA ASUNCION, PABLO|||0000-0003-2141-3069
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] Mo- and W-based oxidic bronzes, with and without Te-atoms in framework positions are active and selective, for the partial oxidation of H2S to sulfur in the 160–220 C temperature range. The catalysts have been prepared by a hydrothermal synthesis and heat-treated in N2 at 600 C, and characterized by several physico-chemical techniques, i.e. AAS, SBET, XRD, SEM–EDX, DR UV–vis and XPS. Te-free catalysts are active, selective and stable for the partial oxidation of H2S to sulfur. V-atoms in Mo– O–V pairs can be proposed as the active sites. Moreover, Te-containing materials show fast catalyst decay. This catalyst deactivation can be related to the presence of Te0 and MoS2, which are observed in used catalyst., Financial support from DGICYT in Spain through Project CTQ2009-14495 is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Reflux Method as a Novel Route for the Synthesis of MoVTeNbOx Catalysts for Selective Oxidation of Propane to Acrylic Acid

  • Ramli, Irmawati
  • Ivars Barceló, Francisco
  • Meng, Woi Pei
  • Zawawi, Siti Murni Mohamad
  • Ahangar, Hossein Abbastabar
  • Hernández Morejudo, Selene
  • BOTELLA ASUNCION, PABLO|||0000-0003-2141-3069
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] This work reports the applicability of reflux to the synthesis of Mo-V-Te-Nb-O metal oxide catalysts for the first time. The well-formed and defined orthorhombic M1 phase, i.e. Te2M20O57 (M = Mo, V, Nb), was found to be better developed when a longer time was used to reflux the mixed metal clusters. The catalysts efficient for propane selective oxidation to acrylic acid, reaching ca. 60% of selectivity to acrylic acid at propane conversion of ca. 50% and at a reaction temperature of 693 K. In addition, a parallel between catalytic activity and catalyst reducibility is also concluded. (C) 2011 Elsevier B.V. All rights reserved., The authors would like to thank the Malaysian government (Science Fund 03-01-04-SF0642 and research fellowship grants) and DGICYT in Spain (Project CTQ2009-14495) for their financial support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Catalytic abatement of trichloroethylene over Mo and/or W-based bronzes

  • Blanch Raga, Neus
  • Soriano Rodríguez, Mª Dolores|||0000-0002-1799-895X
  • Palomares Gimeno, Antonio Eduardo|||0000-0002-6480-6607
  • Concepción Heydorn, Patricia|||0000-0003-2058-3103
  • Martínez-Triguero, Joaquín|||0000-0003-4590-724X
  • López Nieto, José Manuel|||0000-0002-6960-3219
[EN] In this paper we present the results of the synthesis, characterization and catalytic behaviour of Mo(W)¿Nb¿V¿O mixed metal oxides bronzes for the catalytic oxidation of trichloroethylene. The catalysts were prepared hydrothermally with different Mo/W/Nb/V/P atomic ratio and heat-treated at 500 and 700 °C. They were characterized by several techniques as N2-adsorption, X-ray diffraction, FTIR, SEM-EDS, temperature programmed desorption, temperature programmed reduction, UV¿vis, Fourier transformed infrared spectroscopy of adsorbed pyridine and 18O/16O isotope exchange. X-ray diffraction patterns (XRD) of samples heat-treated at 500 °C suggest the presence of a semi-crystalline material with a diffraction peak at ca. 2¿ = 22.2°, while XRD patterns of samples heat-treated at 700 °C show the formation of a tetragonal tungsten bronze (TTB) structure. The activity for the catalytic abatement of trichloroethylene strongly depends on the heat-treatment temperature and the catalyst composition. Thus, samples with W/(Mo + W) atomic ratios of 0.25-0.75 and heat-treated at 500 °C are the most active ones. The enhanced activity has been related to the remarkable higher surface area of the catalyst and to the catalyst composition which influences the acid characteristics as well as the reducibility and reoxidation of the catalysts. The importance of the oxygen dissociation on the catalyst surface and the diffusion of oxygen species through the catalyst are also discussed., The authors wish to thank DGICYT in Spain (Project CTQ2009-14495 and CSD2009-00050-CONSOLIDER/INGENIO 2010) and Universitat Politecnica de Valencia for the financial support. N.B.R. acknowledges Catedra Cemex Sostenibilidad (UPV) for a fellowship. M.D.S. acknowledges Universitat Politecnica de Valencia for a fellowship.